Pricelist valid September. 01, 2006 valid September. 01, 2006 HAWEKA USA, INC . 2 Table of contens Description Page ... Notes 19 . 3 Brand Models HAWEKA-Code Shaft-Ø Code

Pricelist valid September. 01, 2006

HAWEKA USA, INC www.haweka.com

2

Table of contens

Description Page Overview Models 4 – 6 DuoMatic 7 DuoExpert 7 Cones 8 ProGrip Nuts / Shafts 9 Centering Sleeves / Flange Plates / Shafts 10 Flange Plates / Studs 11 WorldKit US 12 QuickPlates 13 UniLug / ProBike II 14 ProClamp Standard / Syncro / Airgolift 15 Centering Kits / Trolley 16 General Accessories / ProTork 17 – 18 Notes 19

3

Brand Models HAWEKA-Code Shaft-Ø

Code Only UL + MCD)

5100 / 5223 / 5500 / 5600 (serial-# 51-0001 – 51-0622) 597 28,55 mm 280 1060 / 6100 / 6600 / 6700 / 6800 507 36 mm 360 5100 / 5600 (serial-# 51-0623 – 51-1457) 5800 / 6000 999 40 mm 400

1200 / 1400 / 1500 958 40 mm 400 1250 / 1450 / 1550 / 1650 589 40 mm 400 8902 460 46 mm - 1850 988 40 mm 400

AMMCO 1030 508 36 mm 360

92 / 920 / 921 (truck-balancer) 957 40 mm 280 9200 (truck-balancer) 818 40 mm 280 Balco 900-series 957 40 mm 280 Balco 9000-series 958 40 mm 280 VPI System / VPI System II 958 40 mm 280 3.2 / 3.3 / 5.1 / 6.6 / 7.5 / 7.6 999 40 mm 818

8.5 / 8.6 / 8.7 818 40 mm 818

80-303 838 40 mm 300

80-1010 / 80-1011 / 80-1012 / 80-1013 40 mm 400

All 818 40 mm 400

4


Code Only UL + MCD)

old 588 36 mm 360

new 589 40 mm 400

700 / 850 / 1001 / 1004 (all with stub shaft) 1025 / 1050 / 1055 / 1250 (all with stub shaft) 938 28,55 mm 280

700 / 850 / 1001 / 1004 (all with over-shaft) 1025 / 1050 / 1055 / 1250 (all with over-shaft) 938 40 mm 400

XR 1750 / XR 1800 / XR 1850 40 mm 400 6200 HS 28,55 mm 280 6401 50,8 mm -

All 907 38 mm 380

All Trucks 46 mm -

All 508 36 mm 360

U 47 / U 87 / U 97 978 40 mm 400

5


Code Only UL + MCD)

All 907 38 mm 380

4100 / 5800 828 40 mm 400

4300 / 5800 MCD 999 40 mm 400

All 818 40 mm 400

GSP 9700 999 40 mm 818

DSP 9200 40 mm 400

MT 1000 – 8000 657 40 mm 400 MT 1000 – 8000 (with 40 mm connection) 658 40 mm 400

MT 800 658 40 mm 400

All 907 38 mm 380

All 589 40 mm 400

6

Drawing Description Part-# MSRP $ Springless Mid Centering Device

DuoMatic (only for wheel balancers with a conical-connection)

• Shaft-Ø 40 mm • Fully adjustable centering from 54 – 115 mm • No additional power required for centering • No counteracting of spring tension • Faster than pneumatic or electro-mechanical clamping systems • Exact centering, tolerance free • Only one centering sleeve • Option to pre-adjust the wheel-hub diameter • Little wear due to nickel-plated surface • HAWEKA Quality – Made in Germany

105 818 000

1,380.00

DuoExpert Shaft-Ø

DuoExpert System. 2 collets in a case 54-75mm. (Ø 28 mm) DuoExpert System. 2 collets in a case 54-75mm. (Ø 36 mm) DuoExpert System. 2 collets in a case 54-75mm. (Ø 38 mm) DuoExpert System. 2 collets in a case 54-75mm. (Ø 40 mm)

164 280 500 164 360 500 164 380 500 164 400 500

725.00

DuoExpert collet 54-65 mm clamping range (Ø 28 mm) DuoExpert collet 54-65 mm clamping range (Ø 36 mm) DuoExpert collet 54-65 mm clamping range (Ø 38 mm) DuoExpert collet 54-65 mm clamping range (Ø 40 mm)

(recommended by Volkswagen AG – VAS 5271)

164 280 501 164 360 501 164 380 501 164 400 501

375.00



164 280 502 164 360 502 164 380 502 164 400 502

.

375.00


164 280 505 164 360 505 164 380 505 164 400 505

375.00

7

Drawing Description Part-# MSRP $

Spacers / Clamping hoods …

Distance ring with magnets for Off-Road cone from the back incl. Pins and Plastic spacer (donut) for Off-Road 190e008 049 210.00

Clamping hood fits ALL Haweka wing nuts 190 008 002 32.00

Pressure ring, fits ALL Haweka wing nuts 190 008 027 7.00

Large diameter (220mm) clamping hood for alloy rims. Fits ALL Haweka wing nuts 190 008 021 62.00

8


Cones Shaft-Ø

Centering cone 1,69” – 2,56” 42 – 64,5 mm (Ø 28 mm) Centering cone 1,69” – 2,56” 42 – 64,5 mm (Ø 36 mm) Centering cone 1,69” – 2,56” 42 – 64,5 mm (Ø 38 mm) Centering cone 1,69” – 2,56” 42 – 64,5 mm (Ø 40 mm)

150 280 008 150 360 008 150 380 008 150 400 008

39.00

Centering cone 2,44” – 3,06” 54 - 79,5 mm (Ø 28 mm) Centering cone 2,44” – 3,06” 54 - 79,5 mm (Ø 36 mm) Centering cone 2,44” – 3,06” 54 - 79,5 mm (Ø 38 mm) Centering cone 2,44” – 3,06” 54 - 79,5 mm (Ø 40 mm)

150 280 009 150 360 009 150 380 009 150 400 009

49.00

Centering cone 2,91” – 4,39” 75 – 111,5 mm (Ø 28 mm) Centering cone 2,91” – 4,39” 75 – 111,5 mm (Ø 36 mm) Centering cone 2,91” – 4,39” 75 – 111,5 mm (Ø 38 mm) Centering cone 2,91” – 4,39” 75 – 111,5 mm (Ø 40 mm)

150 280 012 150 360 012 150 380 012 150 400 012

65.00

Centering cone 3,46” – 5,20” 89 - 132mm (Ø 28 mm) Centering cone 3,46” – 5,20” 89 - 132mm (Ø 36 mm) Centering cone 3,46” – 5,20” 89 - 132mm (Ø 38 mm) Centering cone 3,46” – 5,20” 89 - 132mm (Ø 40 mm)

150 280 049 150 360 049 150 380 049 150 400 049

99.00

3-Centering cone set 1,34” – 4,55” 34-111,5 mm (Ø 28 mm) 3-Centering cone set 1,65” – 4,55” 41-100 mm (Ø 36 mm) 3-Centering cone set 1,65” – 4,55” 41-100 mm (Ø 38 mm) 3-Centering cone set 1,65” – 4,55” 41-100 mm (Ø 40 mm)

150 280 085 150 360 021 150 380 021 150 400 021

131.00

Centering Cone 4,80” – 6,85” 122-174mm (Ø 28 mm) with distance spacer Centering Cone 4,80” – 6,85” 122-174mm (Ø 36 mm) with distance spacer Centering Cone 4,80” – 6,85” 122-174mm (Ø 38 mm) with distance spacer Centering Cone 4,80” – 6,85” 122-174mm (Ø 40 mm) with distance spacer

150 280 091 150 360 091 150 380 091 150 400 091

249.00

9

ProGrip quick nut Shaft-Ø

ProGrip quick nut Tr. 28 x 3 (Ø 28 mm) ProGrip quick nut Tr. 36 x 3 (Ø 36 mm) ProGrip quick nut Tr. 38 x 3 (Ø 38 mm) ProGrip quick nut Tr. 40 x 3 (Ø 40 mm)

143 283 003 143 363 003 143 383 003 143 403 003

135.00

ProGrip quick nut Tr. 28 x 4 (Ø 28 mm) ProGrip quick nut Tr. 40 x 4 (Ø 40 mm)

143 285 003 143 404 003 135.00

ProGrip quick nut with turning handles Tr. 28 x 3 (Ø 28 mm) ProGrip quick nut with turning handles Tr. 36 x 3 (Ø 36 mm) ProGrip quick nut with turning handles Tr. 38 x 3 (Ø 38 mm) ProGrip quick nut with turning handles Tr. 40 x 3 (Ø 40 mm)

143 283 006 143 363 006 143 383 006 143 403 006 147.00

ProGrip quick nut with turning handles Tr. 28 x 4 (Ø 28 mm) ProGrip quick nut with turning handles Tr. 40 x 4 (Ø 40 mm)

143 285 006 143 404 006

147.00

ProGrip nut Metal-Version 40 x 8(only Hunter)

140 408 022 240.00

ProGrip nut Metal-Version 40 x 3

140 403 033 220.00

ProGrip nut Metal-Version 40 x 4

140 404 033 220.00

Repair Kit ProGrip 28 x 3 Repair Kit ProGrip 36 x 3 Repair Kit ProGrip 38 x 3 Repair Kit ProGrip 40 x 3 Repair Kit ProGrip 40 x 4

141e285 310 141e363 310 141e383 310 141e403 310 141e404 310

105.00

Threaded pieces for ProGrip 28x 3 Threaded pieces for ProGrip 36x 3 Threaded pieces for ProGrip 38x 3 Threaded pieces for ProGrip 40x 3 Threaded pieces for ProGrip 40x 4

141e285 302 141e363 302 141e383 302 141e403 302 141e404 302

86.00


10


Centering Sleeves (recommended by car manufacturers) Shaft-Ø

Centering sleeve BMW 57 / 72,5 / 74 mm (Ø 28 mm) Centering sleeve BMW 57 / 72,5 / 74 mm (Ø 36 mm) Centering sleeve BMW 57 / 72,5 / 74 mm (Ø 38 mm) Centering sleeve BMW 57 / 72,5 / 74 mm (Ø 40 mm)

160 280 031 160 360 031 160 380 031 160 400 031

87.00

Centering sleeve Mercedes Benz 66,5 / 84 / 85 mm (Ø 28 mm) Centering sleeve Mercedes Benz 66,5 / 84 / 85 mm (Ø 36 mm) Centering sleeve Mercedes Benz 66,5 / 84 / 85 mm (Ø 38 mm) Centering sleeve Mercedes Benz 66,5 / 84 / 85 mm (Ø 40 mm)

160 280 051 160 360 051 160 380 051 160 400 051

87.00

Centering sleeve Toyota / Nissan / Off-Road (Ø 28 mm) Centering sleeve Toyota / Nissan / Off-Road (Ø 36 mm) Centering sleeve Toyota / Nissan / Off-Road (Ø 38 mm) Centering sleeve Toyota / Nissan / Off-Road (Ø 40 mm)

160 280 053 160 360 053 160 380 053 160 400 053

150.00

Flange Plates Shaft-Ø

Flange Plate Adaptor 4x100/ 5x120, BMW (spring-loaded studs needed) (Ø 28 mm) Flange Plate Adaptor 4x100/ 5x120, BMW (spring-loaded studs needed) (Ø 36 mm) Flange Plate Adaptor 4x100/ 5x120, BMW (spring-loaded studs needed) (Ø 38 mm) Flange Plate Adaptor 4x100/ 5x120, BMW (spring-loaded studs needed) (Ø 40 mm)

211e201 280 211e201 360 211e201 380 211e201 400

162.00

Flange Plate Adaptor 3x112/ 5x112/ 130/ 140 Mercedes Benz (Ø 28 mm) Flange Plate Adaptor 3x112/ 5x112/ 130/ 140 Mercedes Benz (Ø 36 mm) Flange Plate Adaptor 3x112/ 5x112/ 130/ 140 Mercedes Benz (Ø 38 mm) Flange Plate Adaptor 3x112/ 5x112/ 130/ 140 Mercedes Benz (Ø 40 mm)

201e402 280 201e402 360 201e402 380 201e402 400

162.00

Plug-in stud 80 mm long, long taper (Ø 12 mm – for BMW / MB Plate) 271 804 014 21.00 Plug-In Stud, spring-loaded, 100 mm long (Ø 12 mm - for BMW / MB Plate) 271 994 008 34.00

Threaded Shafts Threaded Shaft – Super long Corghi / Faip Sice 212 mm longTr. 38 x 3 170 907 004 173.00Threaded Shaft – Super long Coats Tr. 28,55 x 3 170 937 001 112.00Enlargement Shaft – Super long Coats 850 / 950 / 1050 Tr. 40 x 3 170 937 002 162.00Threaded Shaft – Super long Balco / Sun / Snap On 200 mm Tr. 28,55 x 3 170 957 002 154.00Threaded Shaft – Super long Balco / Sun / Snap On 200 mm Tr. 28,55 x 3,5 170 957 011 154.00Enlargement Shaft – Super long Balco Tr. 40 x 3 170 958 001 162.00Enlargement Shaft – Super long JBC USA / Snap On Tr. 40 x 4 170 958 002 162.00

Threaded Shaft – Super long Corghi / Faip Pneu. QL-Version Tr. 38 x 3 173 907 005 135.00

11


Flange Plates Shaft-Ø

Flange Plate Adaptor , color-coded, without studs 3x98/ 3x112/ 3x114,3/ 3x115/ 3x127/ 6x135/ 6x139,7/ 4x165,1 (Ø 28 mm) (Ø 36 mm) (for Ø 11 mm studs) (Ø 38 mm) (Ø 40 mm)

231e901 289 231e901 369 231e901 389 231e901 409

208.00

Flange Plate Adaptor, color-coded, without studs 4x95,25/ 4x98/ 4x100/ 4x101,6/ 4x108/ 4x114,3/ 7x150/ 4x170 (Ø 28 mm) (Ø 36 mm) (for Ø 11 mm studs) (Ø 38 mm) (Ø 40 mm)


241e801 289 241e801 369 241e801 389 241e801 409

196.00

Flange Plate Adaptor, color-coded, without studs 5x98/ 5x108/ 5x110/ 5x115/ 5x120,65/ 5x135/ 5x154,95 (Ø 28 mm) (Ø 36 mm) (for Ø 11 mm studs) (Ø 38 mm) (Ø 40 mm)

251e701 289 251e701 369 251e701 389 251e701 409

196.00

Flange Plate Adaptor, color-coded, without studs 5x100/ 5x112/ 5x114,3/ 5x120/ 5x127/ 5x130/ 5x139,7/ 5x150/ 5x165,1 (Ø 28 mm) (Ø 36 mm) (for Ø 11 mm studs) (Ø 38 mm) (Ø 40 mm)


251e901 289 251e901 369 251e901 389 251e901 409

219.00

Studs

Plug-in stud "I" 100 mm long (Ø 11 mm) 271 994 117 21.00 Plug-In Stud "III" 90 mm long, rounded head (Ø 11 mm) 271 904 119 21.00

Plug-In Stud "V" 100mm long, short taper (Ø 11 mm) 271 994 121 21.00

Plug-In Stud "IV" 80 mm long, Range Rover (Ø 11 mm) (recommended for WorldKit US) 271 804 120 27.00

Plug-In Stud "II" 80 mm long, short taper ( (Ø 11 mm) 271 804 118 21.00

Plug-In Stud "B" 66 mm long, (Ø 11 mm) 271 664 103 21.00

12


WorldKit US-Version Shaft-Ø

Set of 4 Flange Plate Adaptors WorldKit US, professional US set with 3 sets of studs, color-coded, 1 wall board, wallchart, CD-Rom

1 x Flange Plate Adaptor , color-coded, 3x98/ 3x112/ 3x114,3/ 3x115/ 3x127 / 3 x 130/ 6x135/ 6x139,7/ 4x165,1 1 x Flange Plate Adaptor, color-coded, 4x95,25/ 4x98/ 4x100/ 4x101,6/ 4x108/ 4x114,3/ 7x150/ 4x170 1 x Flange Plate Adaptor, color-coded, 5x98/ 5x108/ 5x110/ 5x115/ 5x120,65/ 5x135/ 5x154,95 1 x Flange Plate adaptor, color-coded, 5x100/ 5x112/ 5x114,3/ 5x120/ 5x127/ 5x130/ 5x139,7/ 5x150/ 5x165,1

6 x Plug-in stud "I" 100 mm long 5 x Plug-In Stud "III" 90 mm long, rounded head 7 x Plug-In Stud "V" 100mm long, short taper

WorldKit US without wallboard

Ø 28 mm: 200 209 285 Ø 36 mm: 200 209 365 Ø 38 mm: 200 209 385 Ø 40 mm: 200 209 405

200 219 xx5

1,199.00

1,099.00

WorldKit US with trolley 200 229 xx5 1,199.00

13


QuickPlates Shaft-Ø Set of QuickPlates (4-, 5 and 6-hole-plates) (Ø 28 mm) (Ø 36 mm) (Ø 38 mm) (Ø 40 mm)

200 456 285 200 456 365 200 456 385 200 456 405

2,399.00

QuickPlate 4-holes with standard-heads (4 pcs.) (Ø 28 mm) (Ø 36 mm) (Ø 38 mm) (Ø 40 mm)

249 008 280 249 008 360 249 008 380 249 008 400

665.00

QuickPlate 5-holes with standard-heads (10 pcs. = 2 Sets) (Ø 28 mm) (Ø 36 mm) (Ø 38 mm) (Ø 40 mm)

259 008 280 259 008 360 259 008 380 259 008 400

804.00

QuickPlate 6-holes with standard-heads (6 pcs.) (Ø 28 mm) (Ø 36 mm) (Ø 38 mm) (Ø 40 mm)

269 008 280 269 008 360 269 008 380 269 008 400

930.00

Heads

Head, short taper, length: (stud and head) 80 mm, Ø 22,5 mm 273e008 002 13.00

Head, long taper, length: (stud and head) 90 mm, Ø 22,5 mm 273e008 003 13.00

Head, short taper, length: (stud and head) 100 mm, Ø 22,5 mm 273e008 004 13.00

Head, rounded, length: (stud and head). 90 mm, Ø 24,5 mm 273e008 006 13.00

Head, rounded, length: (stud and head). 100 mm, Ø 24,5 mm 273e008 007 13.00

Head, Range-/ Land Rover, (stud and head) 80 mm, Ø 34 mm 273e008 008 13.00

Head, long taper, length: (stud and head) 100 mm, Ø 22,5 mm 273e008 011 13.00

14


UniLug Series 405 (incl. 3 Centering rings) UniLug for machines with 28 mm shaft, Mondolfo, Balco, Snap On, 405 280 108 690.00UniLug for machines with 36 mm shaft, Cemb, Ravaglioli / Accu-Turn 405 360 108 690.00 UniLug for machines with 38 mm shaft, Corghi, Faip, Sice 405 380 108 690.00 UniLug for machines with 40 mm shaft, Cemb, Ravaglioli 405 400 108 690.00

UniLug for machines with conical shaft, Beissbarth, Sicam, Facom, Hofmann, etc.

405 818 108

715.00

Motorcycle Clamping Device STANDARD / PROFESSIONAL

ProBike II Modular System STANDARD for conical shaft 805 818 000 929.00 ProBike II Modular System STANDARD for Power Clamp Hofmann 805 995 000 952.00 ProBike II Modular System STANDARD (Ø 28 mm) Mondolfo / Balco / Snap On 805 280 000 929.00

ProBike II Modular System STANDARD (Ø 36 mm) Cemb 805 360 000 929.00 ProBike II Modular System STANDARD Cemb CB 114 / C34 805 768 000 929.00 ProBike II Modular System STANDARD (Ø 38 mm) Corghi 805 380 000 929.00

ProBike II Modular System STANDARD (Ø 40 mm) Cemb / Ravaglioli / Mondolfo (`05 - ) 805 400 000 929.00

ProBike II Upgrade Kit Modular System PROFESSIONAL (conical) 805 818 001 685.00 ProBike II Upgrade Kit Modular System PROFESSIONAL Power Clamp Hofmann 805 995 001 716.00

ProBike II Modular System PROFESSIONAL for cylindrical shaft 805 008 001 685.00

15


ProClamp STANDARD (with spring-loaded feet) Set: (4 pieces) ProClamp for Bear 912 608 543 2,213.00Set: (4 pieces) ProClamp for Hunter 912 618 543 2,213.00Set: (4 pieces) ProClamp for JBC/FMC V3 912 827 543 2,213.00Set: (4 pieces) ProClamp for JBC V6 / V7 912 828 543 2,213.00Set: (4 pieces) ProClamp for John Bean (V501/901 3D) 912 829 543 2,213.00Set: (4 pieces) ProClamp for Corghi 912 907 543 2,213.00Set: (4 pieces) ProClamp for Facom 912 978 543 2,213.00Set: (4 pieces) ProClamp for Cemb / RAV / Space 912 988 543 2,213.00

Set: (4 pieces) ProClamp for Beissbarth 912 998 543 2,213.00

ProClamp SYNCRO Set: (4 pieces) ProClamp Syncro for Hunter incl. attachment shafts 925 618 543 3,222.00Set: (4 pieces) ProClamp Syncro for John Bean JBC2001 incl. attachment shafts 925 829 543 3,222.00Set: (4 pieces) ProClamp Syncro for Corghi incl. attachment shafts 925 907 543 3,222.00

Set: (4 pieces) ProClamp Syncro for Beissbarth incl. attachment shafts

925 998 543 3,222.00

AirgoLift Lifting Device

AirgoLift, wheel lifting device for balancers (incl. air-connection)

The special unit to lift and settle heavy tire service The AirgoLift allows you to achieve the best positioning of the tire on the balancer shaft. The tire is always correctly clamped.

In addition to this, there is no strain from the shaft to the tire during the clamping process. You don´t get any falsified results due to the lack of distortion in the connection. Max. lifting height: 385 mm Max. horizontal range: 460 mm Max. lifting weight: 70kg Weight net: 45 kg

(recommended by Volkswagen AG - VAS 6318)

AirgoLift, wheel lifting device for balancers / black colour (incl. air-connection)

916 000 012 916 000 014

1,412.00

1,412.00

16

Drawing Description Part-# MSRP $ Centering Kits Shaft-Ø

• The solution for rims which can´t be centered easily • Double centering accuracy • High performance design

Ford / GM Multi Kit for 16”-rims (Ø 28 mm) (Ø 36 mm) - Centering Disk 165,1 (Ø 38 mm) - Flange Plate 8 x 165,1 / 6,5“ (Ø 40 mm)

280 280 044 280 360 044 280 380 044 280 400 044

687.00

Ford / GM Adaptor Kit for 19,5”-rims (Ø 28 mm) (Ø 36 mm) - Flange Plate 5 x 184,15 (Ø 38 mm) - Centering Disk 184,15 mm / 133,35 (Ø 40 mm)

280 280 036 280 360 036 280 380 036 280 400 036

412.00

Ford Adaptor Kit for 19” and 16”-rims (Ø 28 mm) (Ø 36 mm) - Centering Disk 169,95 / 170,15 mm (Ø 38 mm) - 4-Arm-Star / PCD: 170 / 225 (Ø 40 mm)

280 280 048 280 360 048 280 380 048 280 400 048

910.00

GM Off Road / Truck Adaptor Kit for 19,5” and 16”-rims (Ø 28 mm) (Ø 36 mm) - Centering Disk 115,88 mm (16”) (Ø 38 mm) - Centering Disk 133,35 mm (Ø 40 mm) - Flange Plate 4 x 165,1

280 280 049 280 360 049 280 380 049 280 400 049

682.00

Flange Plate Storage Facility “Trolley“ with perforated plate and 40 mm Ø pins Flange Plate Storage Facility “Trolley“ with tray and 40 mm Ø pins Flange Plate Storage Facility “Trolley“ with perforated plate and 28 mm Ø pins Flange Plate Storage Facility “Trolley“ with tray and 28 mm Ø pins

900 008 127 900 008 128 900 008 133 900 008 134 155.00

17


General Accessories

Rim width caliper with ears for inside measurement 900 008 005 33.00

Wheel weight plier 900 008 006 29.00

Weightscraper 900e008 089 12.00

ProTork Yellow, 90 Nm, 19 mm 950 008 001 51.00

ProTork red, 110 Nm, 17 mm 950 008 002 51.00

ProTork grey, 135 Nm, 19 mm 950 008 003 51.00

ProTork light brown, 110 Nm, 21 mm 950 008 004 51.00

ProTork blue, 110 Nm, 19 mm 950 008 005 51.00

ProTork dark grey, 135 Nm, 13 / 16“ 950 008 006 51.00

18


General Accessories

ProTork green, 75 Nm, 17 mm 950 008 007 51.00

ProTork black, 80 Nm, 21 mm Best.- 950 008 008 51.00

ProTork white, 160 Nm, 7/8” 950 008 009 51.00

ProTork turquoise, 190 Nm, 7/8” 950 008 010 51.00

ProTork dark brown, 75 Nm, 19 mm 950 008 011 51.00

ProTork beige, 95 Nm, 17 mm 950 008 012 51.00

ProTork orange, 150 Nm, 17 mm 950 008 013 51.00

ProTork beige, 130 Nm, 22 mm 950 008 014 51.00

ProTork fir-green, 85 Nm, 17 mm 950 008 015 51.00

ProTork holding device (for 5 sticks) 950 008 020 16.00

19

Notes

20

Vers. USA_Vc

HAWEKA USA, INC

150 Parkway West Duncan SC 29334

Phone: 18664429352 e-mail: [email protected]

www.haweka.com

Documents

Pricelist valid September. 01, 2006 valid September. 01, 2006 HAWEKA USA, INC . 2 Table of contens Description Page ... Notes 19 . 3 Brand Models HAWEKA-Code Shaft-Ø Code