Embed Size (px)
Citation preview
S 0 1 7 6 9 - A 0 0 0
Angle Port Position045 Optional angles: 20 to 45 deg in 5deg Increments A Port @ Pos.1 (Shown)
B Port @ Pos.2Actuator C Port @ Pos.3
01 Welker 150mm Bore w/ NPT Ports D Port @ Pos.402 Welker 150mm Bore w/ G Ports
Switch MountingShroud 0 No switch
0 No Shroud 1 Position 1 (N/A for World Sw)1 Shroud 2 Position 2
3 Position 3 (N/A for World Sw)Mount 4 Position 4
A Mounting Base as ShownB Mounting Base Rotated 180deg Switch Options
00 No Switching Req'dLX See Switch ChartAE World Switch ( See world Switch Chart)
ORDERING INFORMATION
SCALE
TOOL NAME
DRAWN BY LAST EDIT BYDATE
FILE
NAME
DJH 6/2/2017 DJH
S01769L01
LONG STROKE PART EJECTOR
EXCEPT AS NOTED
DECIMAL TOL. SHALL BE:
0 PLACE (FRACTIONS) `.400 [1/64"]
1 PLACE `.200 [0.010"]
2 PLACE `.100 [0.005"]
3 PLACE `.010 [0.0005"]
ALL DOWEL LOC`0.010[.0005"]
BETWEEN HOLES
SHEET 1 OF 3
1/5
BEARING COMPANY
ENG
APPROVAL
EXCEPT AS NOTED, MAXIMUM
ALLOWABLE ROUGHNESS SHALL BE:
1 PLACE FINISH 6 MICRONS (250 MICROINCHES)
2 PLACE FINISH 3 MICRONS (125 MICROINCHES)
3 PLACE FINISH 1.6 MICRONS (63 MICROINCHES)
UNITS ARE MILLIMETERS(i.e.X.XXmm [x.xxx"])
DO NOT SCALE DRAWING
REV REV BY DESCRIPTIONREV DATE
3 DJH 2/14/2017 ADDED MOUNTING POSITION OPTION FOR LX SWITCH
CHK BY
GSK
*
MOUNT "A"MOUNT "B"
NOTE: 15.2mm [.60"] PRIOR TO THE END OF VERTICAL LIFT, PLATE BEGINS TIPPING MOTION*
LOADING CAPACITY:THIS EJECTOR UNIT AT 60psi HAS A VERTICAL LIFTING CAPACITY OF 1000lbs WITH A MAX RECOMMENDED WORKING TORQUE OF 2200in-lbs, RELATIVE TO THE PIVOT POINT. THE LIFT FORCE AND TORQUES ARE DIRECTLY PROPORTIONAL TO THE AIR PRESSURE.
47 [1.8]
0.00
[0.0
00]
75.0
0 [2
.953
]
150.
00 [5
.906
]
0.00 [0.000]
180.00 [7.087]
PIVOT POINT
90.00 [3.543]
20.00 [0.787] KEY X 60.0 LG
0.00 [0.000]
50.00 [1.969]
50.00 [1.969]
388 [15.3]
RETRACTED
10.0 [0.39]
45.00 [1.772]
115.00 [4.528]
125.00 [4.921] CENT
45.00 [1.772] CENT
4X M16x2 TAP x 35.0
15.0 [0.59]
170.00 [6.693]
35.0 [1.38]
218 [8.6]
20.0 [0.79] KEY X 125.0 LG
2X n16.0 P.F. x 32.0
2,200in-lbf MAXRCMD'D WORKING TORQUE
45° MAX TIP
290.6 [11.44] FOR 45°
(SUBTRACT 10.0 [0.39]FOR EVERY 5°)
2X 3
4" NPT PORTS
6" BORE AIR CYLINDER
P2 P4 P1 P3
P1
P3
P2P4
150.0 [5.91]
FOR "B" MOUNTSWITCH NOTE:
CYLINDICATOR READ DEPTH 2.062"
PROVISIONS FOR CYLINDICATOR(CUSTOMER SUPPLIED)
AVAILABLECYLINDER SWITCH (LX)SHOWN IN POSITION 1
OPTIONAL SHROUD
301.5 [11.87]
294.5 [11.59]
8X M16x2 - TAP x 24.0
WORLD SWITCH OPTION
4X n16.0 P.F. x 24.0
TO DETERMINE THE MAXIMUM WEIGHT FOR THIS PART POSITIONER, DETERMINE YOUR DISTANCE FROM THE CENTER OF MASS OF THE TOOLING TO THE PIVOT POINT IN INCHES. THEN DIVIDE 2,200in-lbf BY THAT DISTANCE. THIS WILL RESULT IN THE MAXIMUM ALLOWABLE WEIGHT IN POUNDS.
2,200in-lbfDISTANCE = MAX WEIGHT in POUNDS
Print date: 6/2/17 Please contact Welker for current drawing: [email protected]
Switch
Option
S01 Sensor
Position -
"E"xtended
"R"etracted Manufacturer's Part Number Mfr. Description
A E or R Ni2-Q6.5-AP6-0.1-FS 4.4X3/S304 Turck3-Wire, 4-Pin, DC M12 X 1
(PNP) Quick Disconnect
B E or R Ni2-Q6.5-ADZ32-0.1-FSB 5.4X4/S304 Turck4-Wire, 5-Pin, AC/DC 1/2-20
(N.O.) Quick Disconnect
C E or R NI2-Q6.5-AN6-0.1-FS 4.4X3/S304 Turck3-Wire, 4-Pin, DC M12 X 1
(NPN) Quick Disconnect
D E or R NBN2-F581-100S6-E8-V1Pepperl &
Fuchs
3-Wire, 4-Pin, DC M12 X 1
(PNP) Quick Disconnect
E E or R BES-Z02KR2-PSC20F-P100-S04-V Balluff3-Wire, 4-Pin, DC M12 X 1
(PNP) Quick Disconnect
H E or R Ni2-Q6.5-0.1M-BDS-2AP6X3-H1141/S34 Turck3-Wire, 4-Pin, DC M12 X 1
(PNP) Quick Disconnect
J E or R IN5374 Efector4-Wire, 4-Pin, DC M12 X 1
(PNP) Quick Disconnect
Switch
Option Mfr. Description
L3 Welker4-Wire, 4-Pin, DC (PNP)
M12 X 1 Quick Disconnect
L5 ifm Efector3-Wire, 4-Pin, DC (NPN)
M12 X 1 Quick Disconnect
WO
RL
D S
WIT
CH
ES
CY
LIN
DE
R S
WIT
CH
ES
Standard Switch Option - All other options may affect price and delivery
SWITCH L3
L3 switch is weld field immune, comparable to World
Switches. L3 is a dual sensor, single connector switch: 1
switch required per cylinder
MK5113
Single sensor, single connector switch:
2 switches required per cylinder
Manufacturer's Part Number
Print date: 6/2/17 Please contact Welker for current drawing: [email protected]
