ProCurve MSM765zl Mobility Controller - 群環科技 … docu… · · 2009-05-20HP ProCurve MSM765zl Mobility Controller J9370A HP ProCurve Switch 5406zl J8697A ... The HP ProCurve

ProCurve MSM765zl Mobility Controller Installation and Getting Started Guide

MSM765-IGSG-5992-5964.book Page 1 Thursday, April 2, 2009 6:48 PM


HP ProCurve MSM765zlMobility Controller

Installation and Getting Started Guide

MSM765-IGSG-5992-5964.book Page i Thursday, April 2, 2009 6:48 PM

Hewlett-Packard Company8000 Foothills Boulevard, m/s 5552Roseville, California 95747-5552http://www.procurve.com

© Copyright 2009 Hewlett-Packard Development Company, L.P.

Publication Number

5992-5964 April 2009

Applicable Products

Software Credits and Notices

SSL on HP ProCurve Switches is based on the OpenSSL software toolkit. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. For more information on OpenSSL, visit www.openssl.org.

Disclaimer

HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard.

Warranty

See the Customer Support/Warranty booklet included with the product.

A copy of the specific warranty terms applicable to your Hewlett-Packard products and replacement parts can be obtained from your HP Sales and Service Office or

Safety

Before installing and operating these products, please read the “Installation Precautions” in chapter 1, and the safety statements in Appendix A, “EMC Regulatory Statements”.

Web Version of this Document

The printed version of this document that was shipped with the HP ProCurve MSM765zl contains the latest information at time of printing. To view or download the latest version of this document and other documentation, visit: www.procurve.com/customercare/support/manuals/index.htm.

HP ProCurve MSM765zl Mobility Controller J9370A

HP ProCurve Switch 5406zl J8697A

HP ProCurve Switch 5406zl-48G J8699A


HP ProCurve Switch 5412zl-96G J8700A


MSM765-IGSG-5992-5964.book Page ii Thursday, April 2, 2009 6:48 PM

http://www.hp.com/go/hpprocurve

1

Contents

1 Hardware Installation

MSM765zl Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Installing the MSM765zl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Verifying the MSM765zl is Installed Correctly . . . . . . . . . . . . . . . . . . . . 1-4

Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

2 Getting Started

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Connect to the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Verify Switch Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Activate the MSM765zl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Obtain the Activation Hardware ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Register the MSM765zl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Install the Product License Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Configure the Switch for the MSM765zl . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

About MSM765zl Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Initial MSM765zl Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Determine Switch Index of the MSM765zl . . . . . . . . . . . . . . . . . . . . . . 2-10

Assign an IP Address to the MSM765zl LAN Port . . . . . . . . . . . . . . . . 2-11

Configure the MSM765zl Internet Port . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Additional Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Restarting and Resetting the MSM765zl . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Restarting the MSM765zl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Resetting an MSM765zl to Factory Defaults . . . . . . . . . . . . . . . . . . . . 2-16

3 Troubleshooting

HP Customer Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1


2

A EMC Regulatory Statements

U.S.A. - FCC Class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Australia/New Zealand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Japan - VCCI Class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Korea . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Taiwan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

B Waste Electrical and Electronic Equipment (WEEE)

Statements

C Hardware Components

Front Panel Port and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Serial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2

Switch LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4

Replacing or Removing an MSM765zl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4

Replacing the Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5

Replacing the Flash Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6

Index


1-1

1

Hardware Installation

MSM765zl OverviewThe HP ProCurve Networking MSM765zl Mobility Controller is a Services zl Module-based WLAN controller. It plugs in to either the 5400zl or 8212zl switches. The MSM765zl Mobility Controller is referred to in this document as the MSM765zl. New switches need to be prepared according to their supplied documentation.

A maximum of four MSM765zls can be installed in the same chassis. Under certain conditions, a maximum of three MSM765zls are supported in the 5406zl chassis. See “Environmental Specifications” on page 1-5.

Figure 1. Front panel of the MSM765zl

See also “Front Panel Port and LEDs” on page C-1.

N o t e This manual contains the basic information needed to get you started using the MSM765zl. It also contains EMC Regulatory Statements (Appendix A) and Waste Electrical and Electronic Equipment (WEEE) Statements (Appendix B). Appendix C provides hardware component information.

For more information on working with the MSM765zl, see the MSM7xx

Controllers Management and Configuration Guide. The latest version of this and all HP ProCurve Networking documentation is available at: www.procurve.com/customercare/support/manuals/index.htm.

MSM765zl Locator LED

HDD and CF Status LEDs

HDD and Network activity LEDs USB port

Module Status LED


http://www.procurve.com/manuals

1-2

Hardware InstallationInstalling the MSM765zl

Installing the MSM765zl

To install the MSM765zl into a switch, the switch can be powered on or off. The following procedure assumes the switch is powered on.

Installation Procedure

1. Use a Torx T-10 or flat-bladed screwdriver to unscrew the screws in the cover plate over the slot where the MSM765zl is to be installed. Remove the cover, and store the cover plate for possible future use.

2. Hold the MSM765zl by its bulkhead—taking care not to touch the metal connectors or components on the board.

3. Open the extractor handles.

Installation Precautions

■ Static electricity can severely damage the electronic components on the MSM765zl. When handling and installing the MSM765zl, follow these procedures to avoid damage from static electricity:

• Handle the MSM765zl by its bulkhead or edges and avoid touching the components and the circuitry on the board.

• When installing the MSM765zl, equalize any static charge difference between your body and the switch by wearing a grounding wrist strap and attaching it to the switch’s metal body, or by frequently touching the switch’s metal body.

■ The MSM765zl has “low-force”, high-performance connectors. High insertion forces are not necessary to install the MSM765zl, and should not be used.

■ Ensure the MSM765zl is fully inserted. Press the MSM765zl into the slot until the bulkhead on the MSM765zl contacts or is very close to contacting the front face of the switch chassis.

■ Once the MSM765zl is fully inserted, screw in the two retaining screws to secure the MSM765zl in place.

■ For safe operation, proper switch cooling, and reduction of electromag-netic emissions, ensure that a slot cover is installed on any unused MSM765zl slot. For safety, no more than one slot should be uncovered at a time when the switch is powered on.

■ Respect the temperature specifications for the MSM765zl.


1-3


4. Insert the MSM765zl aligning with the guides in the slot, and slide it into the slot until it is fully inserted.

5. Once the contacts have engaged, use the extractor handles to seat the MSM765zl completely.

6. Tighten the screws.

Figure 2. MSM765zl being installed

Insert MSM765zl into the guides and slide in until fully inserted.

Open extractor handles


1-4


Verifying the MSM765zl is Installed Correctly

When the MSM765zl is installed properly, it undergoes a self test that takes a few seconds. This happens both when the switch is powered on after installing the MSM765zl, and when the MSM765zl is installed while the switch already has power. The LEDs help determine if the MSM765zl has passed the self test, as described in the following table.

Error Conditions

Error conditions indicated by the MSM765zl LEDs are described in “Front Panel Port and LEDs” on page C-1.

N o t e Allow sufficient time for the MSM765zl to start up, or you will receive an error message.

LED Location of LED

Display for a Properly Installed MSM765zl

Test Switch ON briefly while the MSM765zl is undergoing self test, then OFF.

Note: If the MSM765zl was installed with the switch powered off, and then the switch was powered on, the Test LED will stay ON for the duration of the switch self test.

Figure 6 on page C-4 and Figure 7 on page C-4 show the location of the Test, Fault, and MSM765zl Status LEDs on a 5400zl or 8212zl series switch, respectively.

Fault Switch OFF

Module Status

Switch The LED goes ON as soon as the MSM765zl is installed and the switch is powered on, and stays ON steadily.

Module Status

MSM765zl The LED blinks green during initialization. Solid green means that MSM765zl is operational.Figure 1 on page 1-1 shows the location of all MSM765zl LEDs.

HDD and CF Status

MSM765zl The LED goes ON when HDD/CF initialization was successful. It is OFF by default.


1-5

Hardware InstallationEnvironmental Specifications

Environmental Specifications

Temperature Operating

0°C to 40°C (32°F to 104°F)a, b

a. The maximum operating temperature specification of the chassis is affected by the number and location of the MSM765zls installed in the chassis. For the 5400zl chassis, if all four (the maximum number of MSM765zls allowed in a switch) MSM765zls are installed in the left hand side of the chassis, the maximum operating temperature spec-ification is set to 50°C for the chassis. If any MSM765zls are installed on the right hand side of the chassis, then the temperature specifica-tion for the chassis is 40°C.

A 5406zl chassis has only three slots on the left. To stay within the 50°C temperature specification, only three MSM765zls are supported in this chassis.

b. For the 8212zl chassis, the maximum operating temperature specification is 40°C.

Non-Operating

-10°C to 65°C (-10°F to 149°F)

Relative humidity(non-condensing)

15% to 90% at 40°C (104°F) 15% to 90% at 65°C (149°F)

Maximum altitude 3.0 km (10,000 ft) 4.6 km (15,000 ft)


1-6

Hardware InstallationEnvironmental Specifications


2-1

2

Getting Started

Overview

This chapter describes how to connect to the switch, activate an MSM765zl, configure the switch for the MSM765zl, and then perform initial MSM765zl configuration. Finally, information on restarting and resetting the MSM765zl is provided.

Connect to the Switch

Although full information on the switch command line interface (CLI) is provided in the switch documentation, the basic switch CLI commands needed to work with the MSM765zl are provided in this document.

N O T E Although not described in this document, it is also possible to perform switch configuration via a telnet session with an Ethernet connection to the switch.

1. Using a null-modem (crossover) serial cable, connect a computer to the serial port of the switch Management Module.

2. On the computer, configure a serial terminal program in VT100 mode, with Baud rate 9600, 8 data bits, no parity, 1 stop bit, and no flow control.


2-2

Getting StartedConfigure the Controller

3. Open a terminal session with the switch and press Enter several times until the welcome screen appears. (A different screen may appear if another session was already open.)

4. Press any key to continue. The switch CLI prompt appears. It looks similar to this:

ProCurve Switch 5406zl#

5. If instead, the switch menu is shown, return to the top-level menu and then exit to the CLI by choosing Command Line (CLI) on the Main

Menu.

The switch CLI prompt appears.

Verify Switch Software Version

Before configuring the MSM765zl, verify that the switch software version is compatible with the MSM765zl which requires at least version K.13.51 on the switch.


2-3


At the switch CLI prompt, enter:

show version

The software version information is displayed like this:Image stamp: ...<date, time>K.13.XX...

If the switch software is out-of-date, update it according to the directions in your switch documentation.

Activate the MSM765zl

The MSM765zl must be activated and booted before its own CLI can be used.

The MSM765zl uses the Service OS CLI on the MSM765zl for activation.

The MSM765zl ships with an HP ProCurve MSM765zl Software Activation

License Registration Card in the box. The License Registration ID is printed on this card.

Obtain the Activation Hardware ID

This procedure is performed starting at the switch CLI prompt that looks like this:


N o t e The MSM765zl Service OS CLI is available once the MSM765zl Module Status LED stays on green.

To obtain the activation hardware ID:

1. Change to the switch CLI configuration context:

config

2. Launch the Service OS CLI:services <slot-id> 1

Where <slot-id> identifies the slot containing the MSM765zl. Here is an example with an MSM765zl in slot B:


2-4


Note how the prompt changes to indicate that you are now in the Service OS CLI.

3. Obtain and record the MSM765zl Activation Hardware ID:

licenses hardware-id activation

The Activation Hardware ID is displayed. Record this string precisely as displayed, including the dashes.

Register the MSM765zl

1. Go to the My ProCurve portal https://my.procurve.com.

2. If you are a new user, click, Customer account or Partner account under Create an account and follow the prompts to set up an account.

3. Log into the My ProCurve portal using your My ProCurve user ID and password.

4. Under My Licenses:

a. Select Device Software License.

b. Enter the License Registration ID from the registration card and select Next.

c. The Generate license key for ProCurve device page displays. Enter the Activation Hardware ID, and select Next.

d. Review and accept the License Agreement text.

e. Complete the service information fields.

f. The product license key is generated and displayed, and a confirmation e-mail is sent to you.


https://my.procurve.com

2-5


Install the Product License Key

The starting point for this procedure is the Service OS CLI prompt for the MSM765zl you are activating. If you do not have this prompt available, follow the directions in “Obtain the Activation Hardware ID” on page 2-3.

1. Install the product license key:

licenses install activation <license key>

Where <license key> is the product license key just provided by the My ProCurve portal. The key must be entered precisely as received including the dashes. If possible, copy and paste the string as received. For example:

2. Boot the MSM765zl product:

boot product

The boot image is verified.

3. At prompt:

System will be rebooted.Do you want to continue [y/n]?

Respond with “y”.

The product reboots.

For example:

Configure the Switch for the MSM765zl

The switch must be configured to work properly with the MSM765zl.

This procedure assumes that there are Ethernet port modules installed in slot A, and that the MSM765zl is installed in slot C. Sample VLAN IDs and names are used. You will need to adjust the procedure according to slots chosen and VLAN IDs and names used.


2-6


About MSM765zl Ports

The MSM765zl features two ports, Internet and LAN. These ports do not have RJ-45 Ethernet jacks. Instead, these ports connect through the switch backplane and are mapped to specific RJ-45 jacks on an Ethernet module by VLAN configuration in the switch. The switch references the Internet and LAN ports according to the switch slot in which the MSM765zl is installed. For example, if the MSM765zl is installed in slot C, the first port (C1) corresponds to the Internet port, and the second port (C2) corresponds to the LAN port.

Define and Assign VLANs

1. At the switch CLI prompt, enter:

menu

2. Press Enter. Select Switch Configuration.

3. From the Switch Configuration menu, select VLAN Menu:


2-7


1. Select VLAN Names.

2. Add two VLANs, one for the Internet port and another for the LAN port. For example VLAN ID 10 with name MSM765_Int for the Internet port and VLAN ID 20 with name MSM765_LAN for the LAN port:

3. Select Back to return to the VLAN Menu.

4. Select VLAN Port Assignment.

N o t e In addition to DEFAULT_VLAN, columns are now present for the two VLAN names (MSM765_Int and MSM765_LAN) you defined above. In our example, the MSM765zl Internet port will be assigned to Ethernet port A1 and the MSM765zl LAN port will be assigned to Ethernet port A2.


2-8


5. Select Edit and then use the arrow keys to move the highlight down to the DEFAULT_VLAN column of port C1. Ports C1 and C2 respectively define the VLAN assignment for the MSM765zl Internet and LAN ports.

6. Use the space bar to change values and the arrow keys to move between items. Moving from left to right, set port C1 to No, Untagged, No. Set port C2 to No, No, Untagged. Ports C1 and C2 should now look like this:

7. Use the arrow keys to move the selection highlight to the DEFAULT_VLAN cell for port A1.


2-9


8. Assign ONLY MSM765_Int to port A1, and ONLY MSM765_LAN to port A2. Use the space bar to change values and the arrow keys to move between items. Moving from left to right, set port A1 to No, Untagged, No. Set port A2 to No, No, Untagged. Ports A1 and A2 should now look like this:

9. Consider reserving additional ports for connecting access points to the MSM765zl LAN port. For example, you could set ports A3 and A4 to use the same VLAN as the LAN port, VLAN MSM765_LAN in this example. You could then connect access points to ports A3 and A4 of the Ethernet module.

10. Select Save when done, and then select 0. Return to Main Menu.


2-10


Initial MSM765zl Configuration

Determine Switch Index of the MSM765zl

The starting point for this procedure is the switch CLI prompt that looks like this:


Before you can launch the MSM765zl CLI you must first determine the switch-assigned index of the MSM765zl. Each product type that is based on the Services zl Module (J9154A) like the MSM765zl, gets an index of at least 2 assigned to it by the switch at installation time.

For example, If two MSM765zl modules are installed in a switch with no other Services zl Module-based products already installed, both MSM765zl blades will be assigned an index of 2 by the switch. Later, when a Services zl Module-based blade with a different product is installed in the same switch, it will be assigned an index of 3. Installation sequence per product type determines the index value.

1. To determine the index of your MSM765zl, enter the following at the switch CLI prompt (config should be skipped if you are already in the switch CLI config context):

config services

The Services zl Module products and their assigned indexes are listed like this:

In this example, there is only one type of Services zl Module installed, the MSM765zl. The modules are installed in slots A, B, and C. All three MSM765zl modules have been assigned an index of 2. Take note of the index value.

N o t e Index 1 is reserved for the Service OS CLI for all Services zl Module-based products.

2. Exit the switch CLI config context by typing Control-z. The switch CLI prompt changes so that it now looks like this:



2-11


Assign an IP Address to the MSM765zl LAN Port

The starting point for this procedure is the CLI prompt that looks like this:


To set the MSM765zl LAN port IP address:

1. Select the MSM765zl of interest, specifying the slot and index determined earlier.

services <slot-id> <index>

2. Enable the chosen MSM765zl CLI and select its config context:

enableconfig

3. Select the MSM765zl LAN port interface:

interface ip lan

4. Assign it an IP address of 192.168.1.1 and a subnet mask of 255.255.255.0.

ip address 192.168.1.1/24

The following sample screen shows the commands from the above 4-step procedure, using slot C with an index of 2:

Configure the MSM765zl Internet Port

The procedures in this section are performed with the MSM765zl management tool and a web browser on your computer.

This is an initial configuration procedure for the MSM765zl, enabling you to establish a wired connection through the MSM765zl to the Internet. The MSM765zl is managed via its Web-based management tool using at least Microsoft Internet Explorer 7.0 or Mozilla Firefox 2.0.

N o t e Some prompts only appear when the MSM765zl is in its factory-default state.

1. Disconnect any cable from your computer LAN port, and disable any wireless connection.


2-12


2. Configure the computer to use a static IP address in the range 192.168.1.2 to 192.168.1.254. If necessary, enter the subnet mask. For example, in MS Windows, the subnet mask of 255.255.255.0 is entered automatically when you tab through the field. Set the default gateway to 192.168.1.1, and DNS server to 192.168.1.1.

For example, in Windows XP, select Control Panel > Network

Connections > Local Area Connection > Properties > Internet

Protocol (TCP/IP) > Properties.

3. Connect your computer to the Ethernet port (A2) you assigned to the MSM765zl LAN port.

4. Open a command prompt and confirm that the MSM765zl LAN port can now be pinged at the address to which it was set:

ping 192.168.1.1

5. In a web browser, launch the management tool at the LAN port address https://192.168.1.1.

6. You may be prompted to accept a security certificate. To continue, proceed as follows: At the security certificate prompt, in Microsoft Internet Explorer 7, select Continue to this website; in Firefox 2, select Accept this certificate temporarily for this session and OK.

For information on how you can replace the Secure Sockets Layer (SSL) certificate that ships with the MSM765zl with one of your own, see Managing certificates in the MSM7xx Controller Management and

Configuration Guide.

7. On the Login page, enter admin for Username and Password and then select Login.

8. If presented with a License Agreement page, read the agreement and select Accept License Agreement. This will not appear if you already accepted the agreement on the CLI.

9. If presented with a registration page, register now, or if desired, register later by selecting Service Controller >> Maintenance > Registration.

10. If presented with a Country prompt, choose the country in which this product will be used and select Save.

C a u t i o n The country in which the MSM765zl is operating must be accurately set.


2-13


11. At the password prompt it is recommended that you change the password. Enter the new password and select Save. The management tool home page opens.

12. In the Network Tree select Service Controller, and then in the menu select Network > Ports. Notice how the Internet Port does not yet have an IP address.

13. In this example, the MSM765zl_Int VLAN is on the 192.168.30.x subnet. We enable the MSM765zl DHCP client on the Internet Port and allow the DHCP server on the 192.168.30.x segment to assign an IP address to the MSM765zl.

In the Port configuration table (above), select the Internet Port link. The Internet port configuration page opens.


2-14


14. Select DHCP Client and Configure. The Internet port - DHCP client

configuration page opens.

15. Optionally assign an alternative DHCP Client ID to the MSM765zl. Select Save.

16. The MSM765zl requests an IP address from the DHCP server. You are returned to the Internet port configuration page. Select Save, and then select DHCP Client, Configure again.

17. In the Assigned by DHCP server box, verify that an IP address has been assigned to the MSM765zl Internet port, 192.168.30.141 in this example.

Select Cancel twice to return to the Ports page. The Internet port IP address is now shown.


2-15


18. Assuming that the Internet port (MSM765zl_Int VLAN) has a connection to the Internet, you can test the connection with the management tool Tools > Ping command. Ping a site that is known to permit ping.

Additional Documentation

For detailed information on managing and configuring the MSM765zl, see the MSM7xx Controllers Management and Configuration Guide.

The latest version of this and all HP ProCurve Networking documentation is available at: www.procurve.com/customercare/support/manuals/index.htm.

Restarting and Resetting the MSM765zl

Restarting the MSM765zl

It is recommended that you use the management tool to restart an MSM765zl. In the management tool, select Services Controller >> Maintenance >

System > Restart.

Alternatively, the switch CLI can be used:

1. Enter the switch CLI configuration context:

config

2. Initiate an MSM765zl restart:

services <slot-id> reload

Where <slot-id> identifies the switch slot containing the MSM765zl. A confirmation message appears. Respond with “y” to continue.

The following sample screen shows the commands from the above 2-step procedure for an MSM765zl in slot A:

The MSM765zl can also be restarted, by shutting it down, removing, and reinserting the module.



2-16


Resetting an MSM765zl to Factory Defaults

Use the management tool to reset an MSM765zl to factory defaults. In the management tool, select Service Controller >> Maintenance > Config file

management > Reset configuration > Reset.

When you reset the MSM765zl to factory defaults, it loses its LAN port IP address and Internet port configuration. Once the MSM765zl reboots and the Status LED stays on, type Ctrl-z to return to the switch CLI. Then follow the directions in “Assign an IP Address to the MSM765zl LAN Port” on page 2-11 and “Configure the MSM765zl Internet Port” on page 2-11.


3-1

3

Troubleshooting

Detailed information for the MSM765zl is available in the MSM7xx Controllers

Management and Configuration Guide at www.procurve.com/customercare/support/manuals/index.htm. The latest information for your switch is available from the same web location.

HP Customer Support Services

HP offers support 24 hours a day, seven days a week through the use of a number of automated electronic services. See the Customer Support/Warranty booklet that came with the product for information on how to use these services to get technical support. The HP ProCurve Web portal, at www. procurve.com also provides up-to-date support information.

Additionally, HP ProCurve authorized network resellers can provide assistance, both with services they offer and with services offered by HP ProCurve.



http://www.procurve.com

3-2

TroubleshootingHP Customer Support Services


A-1

A

EMC Regulatory Statements

U.S.A. - FCC Class A

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference when the equipment is used in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. Operation of this equipment in a residential area may cause interference in which case users are required to correct the interference at their own expense.

Canada

This product complies with Class A Canadian EMC requirements.

Australia/New Zealand

This product complies with Australia/New Zealand EMC Class A require-ments.


A-2

EMC Regulatory Statements

Japan - VCCI Class A

Korea

Taiwan


B-1

B

Waste Electrical and Electronic Equipment (WEEE) Statements

Disposal of Waste Equipment by Users in Private Household in the European UnionThis symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Bortskaffelse af affald fra husstande i den Europæiske UnionHvis produktet eller dets emballage er forsynet med dette symbol, angiver det, at produktet ikke må bortskaffes med andet almindeligt husholdningsaffald. I stedet er det dit ansvar at bortskaffe kasseret udstyr ved at aflevere det på den kommunale genbrugsstation, der forestår genvinding af kasseret elektrisk og elektronisk udstyr. Den centrale modtagelse og genvinding af kasseret udstyr i forbindelse med bortskaffelsen bidrager til bevarelse af naturlige ressourcer og sikrer, at udstyret genvindes på en måde, der beskytter både mennesker og miljø. Yderligere oplysninger om, hvor du kan aflevere kasseret udstyr til genvinding, kan du få hos kommunen, den lokale genbrugsstation eller i den butik, hvor du købte produktet.

Seadmete jäätmete kõrvaldamine eramajapidamistes Euroopa LiidusSee tootel või selle pakendil olev sümbol näitab, et kõnealust toodet ei tohi koos teiste majapidamisjäät-metega kõrvaldada. Teie kohus on oma seadmete jäätmed kõrvaldada, viies need elektri- ja elektroon-ikaseadmete jäätmete ringlussevõtmiseks selleks ettenähtud kogumispunkti. Seadmete jäätmete eraldi kogumine ja ringlussevõtmine kõrvaldamise ajal aitab kaitsta loodusvarasid ning tagada, et ringlussev-õtmine toimub viisil, mis kaitseb inimeste tervist ning keskkonda. Lisateabe saamiseks selle kohta, kuhu oma seadmete jäätmed ringlussevõtmiseks viia, võtke palun ühendust oma kohaliku linnakantselei, majapidamisjäätmete kõrvaldamise teenistuse või kauplusega, kust Te toote ostsite.

Likvidace zařízení soukromými domácími uživateli v Evropské unii Tento symbol na produktu nebo balení označuje výrobek, který nesmí být vyhozen spolu s ostatním domácím odpadem. Povinností uživatele je předat takto označený odpad na předem určené sběrné místo pro recyklaci elektrických a elektronických zařízení. Okamžité třídění a recyklace odpadu pomůže uchovat přírodní prostředí a zajistí takový způsob recyklace, který ochrání zdraví a životní prostředí člověka. Další informace o možnostech odevzdání odpadu k recyklaci získáte na příslušném obecním nebo městském úřadě, od firmy zabývající se sběrem a svozem odpadu nebo v obchodě, kde jste produkt zakoupili.


B-2


Laitteiden hävittäminen kotitalouksissa Euroopan unionin alueellaJos tuotteessa tai sen pakkauksessa on tämä merkki, tuotetta ei saa hävittää kotitalousjätteiden mukana. Tällöin hävitettävä laite on toimitettava sähkölaitteiden ja elektronisten laitteiden kierrätyspisteeseen. Hävitettävien laitteiden erillinen käsittely ja kierrätys auttavat säästämään luonnonvaroja ja varmista-maan, että laite kierrätetään tavalla, joka estää terveyshaitat ja suojelee luontoa. Lisätietoja paikoista, joihin hävitettävät laitteet voi toimittaa kierrätettäväksi, saa ottamalla yhteyttä jätehuoltoon tai liikkee-seen, josta tuote on ostettu.

Élimination des appareils mis au rebut par les ménages dans l'Union européenneLe symbole apposé sur ce produit ou sur son emballage indique que ce produit ne doit pas être jeté avec les déchets ménagers ordinaires. Il est de votre responsabilité de mettre au rebut vos appareils en les déposant dans les centres de collecte publique désignés pour le recyclage des équipements électriques et électroniques. La collecte et le recyclage de vos appareils mis au rebut indépendamment du reste des déchets contribue à la préservation des ressources naturelles et garantit que ces appareils seront recyclés dans le respect de la santé humaine et de l'environnement. Pour obtenir plus d'informations sur les centres de collecte et de recyclage des appareils mis au rebut, veuillez contacter les autorités locales de votre région, les services de collecte des ordures ménagères ou le magasin dans lequel vous avez acheté ce produit.

Entsorgung von Altgeräten aus privaten Haushalten in der EUDas Symbol auf dem Produkt oder seiner Verpackung weist darauf hin, dass das Produkt nicht über den normalen Hausmüll entsorgt werden darf. Benutzer sind verpflichtet, die Altgeräte an einer Rück-nahmestelle für Elektro- und Elektronik-Altgeräte abzugeben. Die getrennte Sammlung und ordnungs-gemäße Entsorgung Ihrer Altgeräte trägt zur Erhaltung der natürlichen Ressourcen bei und garantiert eine Wiederverwertung, die die Gesundheit des Menschen und die Umwelt schützt. Informationen dazu, wo Sie Rücknahmestellen für Ihre Altgeräte finden, erhalten Sie bei Ihrer Stadtverwaltung, den örtlichen Müllentsorgungsbetrieben oder im Geschäft, in dem Sie das Gerät erworben haben

Απόρριψη άχρηστου εξοπλισμού από χρήστες σε ιδιωτικά νοικοκυριά στην Ευρωπαϊκή Ένωση Το σύμβολο αυτό στο προϊόν ή τη συσκευασία του υποδεικνύει ότι το συγκεκριμένο προϊόν δεν πρέπει να διατίθεται μαζί με τα άλλα οικιακά σας απορρίμματα. Αντίθετα, είναι δική σας ευθύνη να απορρίψετε τον άχρηστο εξοπλισμό σας παραδίδοντάς τον σε καθορισμένο σημείο συλλογής για την ανακύκλωση άχρηστου ηλεκτρικού και ηλεκτρονικού εξοπλισμού. Η ξεχωριστή συλλογή και ανακύκλωση του άχρηστου εξοπλισμού σας κατά την απόρριψη θα συμβάλει στη διατήρηση των φυσικών πόρων και θα διασφαλίσει ότι η ανακύκλωση γίνεται με τρόπο που προστατεύει την ανθρώπινη υγεία και το περιβάλλον. Για περισσότερες πληροφορίες σχετικά με το πού μπορείτε να παραδώσετε τον άχρηστο εξοπλισμό σας για ανακύκλωση, επικοινωνήστε με το αρμόδιο τοπικό γραφείο, την τοπική υπηρεσία διάθεσης οικιακών απορριμμάτων ή το κατάστημα όπου αγοράσατε το προϊόν.

Készülékek magánháztartásban történő selejtezése az Európai Unió területén A készüléken, illetve a készülék csomagolásán látható azonos szimbólum annak jelzésére szolgál, hogy a készülék a selejtezés során az egyéb háztartási hulladéktól eltérő módon kezelendő. A vásárló a hulladékká vált készüléket köteles a kijelölt gyűjtőhelyre szállítani az elektromos és elektronikai készülékek újrahasznosítása céljából. A hulladékká vált készülékek selejtezéskori begyűjtése és újrahasznosítása hozzájárul a természeti erőforrások megőrzéséhez, valamint biztosítja a selejtezett termékek környezetre és emberi egészségre nézve biztonságos feldolgozását. A begyűjtés pontos helyéről bővebb tájékoztatást a lakhelye szerint illetékes önkormányzattól, az illetékes szemételtakarító vállalattól, illetve a terméket elárusító helyen kaphat.


B-3


Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione EuropeaQuesto simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere smaltito insieme ai rifiuti domestici. È responsabilità dell'utente smaltire le apparecchiature consegnan-dole presso un punto di raccolta designato al riciclo e allo smaltimento di apparecchiature elettriche ed elettroniche. La raccolta differenziata e il corretto riciclo delle apparecchiature da smaltire permette di proteggere la salute degli individui e l'ecosistema. Per ulteriori informazioni relative ai punti di raccolta delle apparecchiature, contattare l'ente locale per lo smaltimento dei rifiuti, oppure il negozio presso il quale è stato acquistato il prodotto.

Verwijdering van afgedankte apparatuur door privé-gebruikers in de Europese UnieDit symbool op het product of de verpakking geeft aan dat dit product niet mag worden gedeponeerd bij het normale huishoudelijke afval. U bent zelf verantwoordelijk voor het inleveren van uw afgedankte apparatuur bij een inzamelingspunt voor het recyclen van oude elektrische en elektronische apparatuur. Door uw oude apparatuur apart aan te bieden en te recyclen, kunnen natuurlijke bronnen worden behouden en kan het materiaal worden hergebruikt op een manier waarmee de volksgezondheid en het milieu worden beschermd. Neem contact op met uw gemeente, het afvalinzamelingsbedrijf of de winkel waar u het product hebt gekocht voor meer informatie over inzamelingspunten waar u oude apparatuur kunt aanbieden voor recycling.

Nolietotu iekārtu iznīcināšanas noteikumi lietotājiem Eiropas Savienības privātajās mājsaimniecībās Šāds simbols uz izstrādājuma vai uz tā iesaiņojuma norāda, ka šo izstrādājumu nedrīkst izmest kopā ar citiem sadzīves atkritumiem. Jūs atbildat par to, lai nolietotās iekārtas tiktu nodotas speciāli iekārtotos punktos, kas paredzēti izmantoto elektrisko un elektronisko iekārtu savākšanai otrreizējai pārstrādei. Atsevišķa nolietoto iekārtu savākšana un otrreizējā pārstrāde palīdzēs saglabāt dabas resursus un garantēs, ka šīs iekārtas tiks otrreizēji pārstrādātas tādā veidā, lai pasargātu vidi un cilvēku veselību. Lai uzzinātu, kur nolietotās iekārtas var izmest otrreizējai pārstrādei, jāvēršas savas dzīves vietas pašvaldībā, sadzīves atkritumu savākšanas dienestā vai veikalā, kurā izstrādājums tika nopirkts.

Vartotojų iš privačių namų ūkių įrangos atliekų šalinimas Europos Sąjungoje Šis simbolis ant gaminio arba jo pakuotės rodo, kad šio gaminio šalinti kartu su kitomis namų ūkio atliekomis negalima. Šalintinas įrangos atliekas privalote pristatyti į specialią surinkimo vietą elektros ir elektroninės įrangos atliekoms perdirbti. Atskirai surenkamos ir perdirbamos šalintinos įrangos atliekos padės saugoti gamtinius išteklius ir užtikrinti, kad jos bus perdirbtos tokiu būdu, kuris nekenkia žmonių sveikatai ir aplinkai. Jeigu norite sužinoti daugiau apie tai, kur galima pristatyti perdirbtinas įrangos atliekas, kreipkitės į savo seniūniją, namų ūkio atliekų šalinimo tarnybą arba parduotuvę, kurioje įsigijote gaminį.

Pozbywanie się zużytego sprzętu przez użytkowników w prywatnych gospodarstwach domowych w Unii Europejskiej Ten symbol na produkcie lub jego opakowaniu oznacza, że produktu nie wolno wyrzucać do zwykłych pojemników na śmieci. Obowiązkiem użytkownika jest przekazanie zużytego sprzętu do wyznaczonego punktu zbiórki w celu recyklingu odpadów powstałych ze sprzętu elektrycznego i elektronicznego. Osobna zbiórka oraz recykling zużytego sprzętu pomogą w ochronie zasobów naturalnych i zapewnią ponowne wprowadzenie go do obiegu w sposób chroniący zdrowie człowieka i środowisko. Aby uzyskać więcej informacji o tym, gdzie można przekazać zużyty sprzęt do recyklingu, należy się skontaktować z urzędem miasta, zakładem gospodarki odpadami lub sklepem, w którym zakupiono produkt.


B-4


Descarte de Lixo Elétrico na Comunidade Européia Este símbolo encontrado no produto ou na embalagem indica que o produto não deve ser descartado no lixo doméstico comum. É responsabilidade do cliente descartar o material usado (lixo elétrico), encaminhando-o para um ponto de coleta para reciclagem. A coleta e a reciclagem seletivas desse tipo de lixo ajudarão a conservar as reservas naturais; sendo assim, a reciclagem será feita de uma forma segura, protegendo o ambiente e a saúde das pessoas. Para obter mais informações sobre locais que reciclam esse tipo de material, entre em contato com o escritório da HP em sua cidade, com o serviço de coleta de lixo ou com a loja em que o produto foi adquirido.

Eliminación de residuos de equipos eléctricos y electrónicos por parte de usuarios particulares en la Unión EuropeaEste símbolo en el producto o en su envase indica que no debe eliminarse junto con los desperdicios generales de la casa. Es responsabilidad del usuario eliminar los residuos de este tipo depositándolos en un "punto limpio" para el reciclado de residuos eléctricos y electrónicos. La recogida y el reciclado selectivos de los residuos de aparatos eléctricos en el momento de su eliminación contribuirá a conservar los recursos naturales y a garantizar el reciclado de estos residuos de forma que se proteja el medio ambiente y la salud. Para obtener más información sobre los puntos de recogida de residuos eléctricos y electrónicos para reciclado, póngase en contacto con su ayuntamiento, con el servicio de eliminación de residuos domésticos o con el establecimiento en el que adquirió el producto.

Likvidácia vyradených zariadení v domácnostiach v Európskej únii Symbol na výrobku alebo jeho balení označuje, že daný výrobok sa nesmie likvidovať s domovým odpadom. Povinnosťou spotrebiteľa je odovzdať vyradené zariadenie v zbernom mieste, ktoré je určené na recykláciu vyradených elektrických a elektronických zariadení. Separovaný zber a recyklácia vyradených zariadení prispieva k ochrane prírodných zdrojov a zabezpečuje, že recyklácia sa vykonáva spôsobom chrániacim ľudské zdravie a životné prostredie. Informácie o zberných miestach na recykláciu vyradených zariadení vám poskytne miestne zastupiteľstvo, spoločnosť zabezpečujúca odvoz domového odpadu alebo obchod, v ktorom ste si výrobok zakúpili.

Odstranjevanje odslužene opreme uporabnikov v zasebnih gospodinjstvih v Evropski uniji Ta znak na izdelku ali njegovi embalaži pomeni, da izdelka ne smete odvreči med gospodinjske odpadke. Nasprotno, odsluženo opremo morate predati na zbirališče, pooblaščeno za recikliranje odslužene električne in elektronske opreme. Ločeno zbiranje in recikliranje odslužene opreme prispeva k ohranjanju naravnih virov in zagotavlja recikliranje te opreme na zdravju in okolju neškodljiv način. Za podrobnejše informacije o tem, kam lahko odpeljete odsluženo opremo na recikliranje, se obrnite na pristojni organ, komunalno službo ali trgovino, kjer ste izdelek kupili.

Bortskaffande av avfallsprodukter från användare i privathushåll inom Europeiska Unionen Om den här symbolen visas på produkten eller förpackningen betyder det att produkten inte får slängas på samma ställe som hushållssopor. I stället är det ditt ansvar at t bortskaffa avfallet genom att överlämna det till ett uppsamlingsställe avsett för återvinning av avfall från elektriska och elektroniska produkter. Separat insamling och återvinning av avfallet hjälper till att spara på våra naturresurser och gör att avfallet återvinns på ett sätt som skyddar människors hälsa och miljön. Kontakta dit t lokala kommunkontor, din närmsta återvinningsstat ion för hushållsavfall eller affären där du köpte produkten för att få mer information om var du kan lämna ditt avfall för återvinning.


C-1

C

Hardware Components

Front Panel Port and LEDs

This section describes the different buttons and LEDs on the front panel of an MSM765zl.

Figure 3. MSM765 front panel

■ USB Port: This port is used to attach a USB device, such as a flash drive.

■ The following table describes the LEDs on the front panel.

MSM765zl Locator LED

HDD and CF Status LEDs

HDD and Network activity LEDs USB port

Module Status LED

MSM765zl LED State Meaning

Module Status (green/orange)

Blinking greenSolid greenBlinking/solid orange

Initialization was successful. Stays in this state when the MSM765zl is booted to Service OS.MSM765zl is operational.Error condition

This LED is off by default.Blinking cycle (green or orange) is 400ms on – 400ms off.At boot, the Module Status, HDD Status, and CF Status LEDs are solid green for ~2s, then solid orange for ~2s, then back to solid green for ~1s, and finally all are turned off.


C-2

Hardware ComponentsSerial Numbers

Serial Numbers

Serial numbers are required when contacting HP or a reseller for warranty assistance or for coverage under a service agreement. For future reference, record the serial and product numbers in the warranty booklet.

The MSM765zl ships as a bundle. From a warranty perspective, a bundle consists of two separate hardware components:■ MSM765zl■ Disk drive.

Refer to the warranty booklet for warranty coverage details for each hardware component.

Module Locator(blue)

Blinking/solid

Solid during boot only when the MSM765zl is inserted into a chassis, soft reboots do not enable this LED. Used to locate a specific module in an area full of chassis. Enabled by using the following switch CLI command:services <slot ID> locate <blink [duration] | off | on [duration]>This LED is off by default.

CF (Compact Flash)/HDD Status (green/orange)

Solid greenSolid orange

CF/HDD has initialized.

CF/HDD is not detected.

This LED is off by default.At boot, the MSM765zl Status, HDD Status, and CF Status LEDs are solid green for ~2s, then solid orange for ~2s, then back to solid green for ~1s, and finally all are turned off.

HDD Activity (green)

Blinking

Off

The drive is active.

The drive is not active.

Network Activity (green)

Blinking

Off

There is network activity on one or both internal ports.

If either of the ports fails, the MSM765zl Status LED is set to blinking orange.

There is no network activity on either port.

MSM765zl LED State Meaning


C-3

Hardware ComponentsSerial Numbers

The serial number of the disk drive is located under the disk drive.

Figure 4. Locating the disk drive serial number

The serial number for the MSM765zl is located on the back left corner of the MSM765zl.

Figure 5. Locating the MSM765zl serial number

The serial number of the MSM765zl can also be found in the management tool or through the CLI.

Disk drive serial and product numbers

SN: SGxxxxxxxx

MSM765zl serial number

SN: SGxxxxxxxx


C-4

Hardware ComponentsSwitch LEDs

Switch LEDs

The following figures show the Test, Fault, and Module Status LEDs on the switches in which the MSM765zl can be installed.

Figure 6. Test, Fault, and Module Status LEDs on a Series 5400zl switch

Figure 7. Test, Fault, and Module Status LEDs on a Series 8212zl switch

Replacing or Removing an MSM765zl

It is highly recommended that the MSM765zl be shut down before replacing or removing it. The MSM765zl may be shut down using the following MSM765zl CLI command:

services <slot-id> shutdown

Where <slot-id> identifies the MSM765zl slot.

It is possible to “hot-swap” one module for another, that is, replace one module with another while the switch is still powered on, without interrupting the operation of the rest of the switch ports. If the modules are not the same type, the switch may have to be reconfigured.

Module Status LEDsTest LEDFault LED

Module Status LEDsFault LED Test LED


C-5

Hardware ComponentsReplacing the Disk Drive

C a u t i o n A 5-second delay is mandatory between removing an MSM765zl, and either re-installing it, or replacing it with another.

To replace one MSM765zl with another, or to remove a MSM765zl without replacing it, use the following procedure:

1. Unscrew the retaining screws enough to disconnect them from the threaded holes in the switch.

2. Using the extractor handles pull the MSM765zl out from the slot.

3. Do one of the following:

• If installing another module of the same type, go to “Installation Procedure” on page 1-2 and begin with step 2. A switch reset is not required. The current configuration in that slot will apply to the new module.

• If another MSM765zl will not be installed in the slot (that is, the slot will be left empty), re-install the cover plate over the slot opening.

C a u t i o n For proper cooling and reduction of electromagnetic emissions, ensure that a slot cover is installed on any unused slot.

Replacing the Disk Drive

The following procedure describes replacing the Disk Drive in the MSM765zl. The MSM765zl may be removed while the switch is powered on. The numbers in Figure 8 on page C-6 correspond to the first four step numbers below.

1. Using either a flat-bladed or Torx T-10 screwdriver loosen the retaining screws securing the MSM765zl.

2. Using the extractor handles, pull the MSM765zl out from the slot and turn it over.

3. Using a Cross Recess Type 1 No.1 (Philips tip) screwdriver remove the four retaining screws holding the disk drive.

4. Slide the disk drive part way back to disconnect it.

5. Position the disk drive in the middle of the disk drive slot.

6. Using either side of the disk drive bracket, lift the disk drive out.

7. Install the new disk drive and slide it forward to engage the connector.

8. Re-install the four retaining screws.


C-6

Hardware ComponentsReplacing the Flash Card

9. Re-install the MSM765zl into the switch.

10. Use an equal amount of pressure and push both extractor handles closed to completely seat the MSM765zl.

11. Tighten the retaining screws.

Figure 8. Steps for Replacing the MSM765zl Disk Drive

Replacing the Flash CardThe following procedure describes replacing the Flash Card in the MSM765zl. The MSM765zl may be removed while the switch is powered on. The numbers in Figure Figure 9 on page C-7 correspond to the first four step numbers below.

1. Using either a flat-bladed or Torx T-10 screwdriver loosen the retaining screws securing the MSM765zl.

1. 2.

3. 4.

Retaining Screws Extractor Handles

Retaining ScrewsDisconnected


C-7


2. Using the extractor handles, pull the MSM765zl out from the slot and turn it over.

3. Slide out the old flash card by applying slight pressure to the top of the flash card.

4. Position the new flash card properly and slide it in being careful not to bend any connector pins.

5. Re-install the MSM765zl into the switch.

6. Use an equal amount of pressure and push both extractor handles closed to completely seat the MSM765zl.

7. Tighten the retaining screws.

Figure 9. Steps for Replacing the MSM765zl Flash Card

1 2

3 4

Retaining Screws Extractor Handles


C-8



Index – 1

A

Activate the MSM765zl … 2-3Activation Hardware ID … 2-4

C

CLI Commandshutdown … C-4

E

EMC Regulatory Statements … A-1Environmental Specifications … 1-5

H

Hardware ID … 2-4HP Customer Support Services … 3-1

I

Install the Product License Key … 2-5Installing the MSM765zl … 1-2

Precautions … 1-2Procedure … 1-2Verifying correct installation … 1-4

L

LEDBehavior … 1-4Fault … 1-4HDD Activity … C-2HDD and CF Status … 1-4, C-2Meaning … C-1Module Locator … C-2Module Status … 1-4MSM765 Status … C-1Network Activity … C-2State … C-1Switch … C-4Test … 1-4

License Key … 2-4

M

MSM765zl Front Panel … 1-1, C-1MSM765zl Registration and Licensing Card … 2-3My ProCurve … 2-4

R

Register the MSM765zl … 2-4Replacing the Disk Drive … C-5Replacing the Flash Card … C-6Resetting to Factory Defaults … 2-16Restarting … 2-15

S

Serial Numbers … C-2, C-3

T

Troubleshooting … 3-1

W

Waste Electrical and Electronic Equipment (WEEE) Statements … B-1

Z

zl Switch … C-4

Index


2 – Index



Printed in March 2009

Manual Part Number

5992-5964

*5992-5964*

Technology for better business outcomes

To learn more, visit www.hp.com/go/procurve/

© Copyright 2009 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP will not be liable for technical or editorial errors or omissions contained herein.


Documents

ProCurve MSM765zl Mobility Controller - 群環科技 … docu… · · 2009-05-20HP ProCurve MSM765zl Mobility Controller J9370A HP ProCurve Switch 5406zl J8697A ... The HP ProCurve