ET-MINI I/O BOARD SET

D TO A # MCP492212 BIT 2 CH

ET-MINI PWR DUAL 5

ET-MINI PWR DUAL 12

ET-MINI TPIC6B595(P-ET-A-00420)

ET-MINI 74165(P-ET-A-00419)

ET-MINI AUDIO OUT(P-ET-A-00296)

ET-MINI MCP4922 DAC 12 BIT(P-ET-A-00305)

ET-MINI SPI DATA FLASH(P-ET-A-00306)

ET-MINI PWR 3.3(P-ET-A-00289)

(P-ET-A-00308)

ET-MINI PWR 5(P-ET-A-00233)

PRODUCT CATALOG 2011ELECTRONICS TECHNOLOGY TEAM

ET-MINI RELAY2(P-ET-A-00360)

Tel : (66) 02-7121120 Fax : (66) 02-3917216 e-mail : sale@etteam.comบริษัท อีทีที จำกัดETT CO., LTD. www.etteam.com Company reserves the right to change the detail and price of any product without any prior notice.

ET-MINI PWR DUAL 5

ET-MINI PWR DUAL 12

ET-MINI SD/MMC(P-ET-A-00298)

ET-MINI LOGIC LEVEL(P-ET-A-00297)

AT45DB16 2MBYTE FLASH MEMORY

(P-ET-A-00307)

INTE

RFA

CE

BO

ARD

71

Board with small accessaries of circuit that isdivided 1 circuit / 1 board and use can selectfor suitable project board.

• Connect INPUT TTL to be 2 I/O 10 PIN ET Connectors,be able to select Bit by Jumper and 2 sets of 3 PIN INPUTConnector (WAFER 3 PIN 2.54 mm)• 2 Output RELAY Contact that are 2 PIN TERMINAL type• 5VDC Power Supply and 12 VDC Power Supply for CoilRELAY

It is MINI Board version from ETT that uses 2 mini LOW POWER RELAY Circuits on board. • Use 2 mini RELAY 12VDC, 1 CONTACT, 3A/250VDC

It is POWER SUPPLY as Step-Down Voltage Regulator type that uses IC No.LM2575S-3.3. It can receive INPUT DC POWER 5-

35V; can give OUTPUT 3.3VDC. CONNECTOR INPUT isDC JACK TYPE 2.5mm; CONNECTOR OUTPUT is MALEHEADER and FEMALE HEADER.

It is a Board of 2MBYTE FLASH Memory by using ICNo.AT45DB16 from ATMEL, so it can be applied for storingdata or DATA LOGGER.• Use IC No.AT45DB16 DIP TYPE TSOP 28 PIN• 2MBYTE FLASH Memory (4096 PAGES x 528 BYTES)• SPI Interface and using with POWER SUPPLY rangefrom 2.5 to 3.3V• Can be interfaced Pin Signal INPUT with Pin Signal 5V• PCB size 4.4 x 5.6 cm. with User's Manual and ExampleProgram in CD

It is one of ET-MINI BOARD that is Circuit

D TO A 12 BIT 2 CH and use IC No.MCP4922 from MICROCHIP.

• Use IC D TO A No.MCP4922 DIP TYPE 14 PIN• 12 BIT OUTPUT 2 CHANNEL• Can set Reference Voltage from VR that can be adjustedvalue from 0 to +VCC.• SPI Interface and can be used with POWER SUPPLYrange from 2.7 to 5.5V.• Can select expansion interface of signal output as X1 or X2 type• PCB size 4.4 x 5.6 cm. with User's Manual and ExampleProgram in CD

It is Board circuit toconnect signal Logic between 5V components and 3.3 V (or 3V)components and uses IC 74CX245 to be medium of connection.Moreover, there is circuit REGULATOR 3.3V on Board.

Board with both SDand MMC SOCKET MEMORY CARD and Signal Pins arearranged to interface with Board Microcontroller easier.Additionally, it can be used with MINI MP3.

It is a mini amplifier with mini speaker on Board andSTEREO JACK to connect with headphone or externalamplifier set.

This is 8BIT SHIFT REGISTER PARALLEL-TO-SERIALDATA CONVERSION that is PARALLEL-IN,SERIAL-OUTfor SPI Interface. It receives incoming data as parallel typeand it sends out data through OUTPUT as serial type. Itsupports the maximum CLOCK Frequency at 35 MHz. Thisboard uses IC No.74LS165.Pin DATA IN is 10 PIN BLOCK Type; and PIN OUTPUT is8PIN HEADER MALE and FEMALE.

This is 8BIT POWER SHIFT REGISTER that is SERIAL-IN,PARALLEL-OUT for SPI Interface. It receives incomingdata as serial type and it sends out data through OUTPUTas parallel type. OUTPUT in each bit is OPEN DRAIN typethat supports the maximum Load Current at 500mA andthe maximum Load Voltage at 50V.Connector V-OUT is TERMINAL 2PIN Type; ConnectorOUTPUT is 10PIN BLOCK type; Connector INPUT 8PINHEADER MALE and FEMALE.

It is POWER SUPPLY that has positive and negative powersupply from OUTPUT and only positive power supply fromINPUT. In this case, it uses 2 Circuit STEP-DOWN VOLT-AGE REGULATORS; No.LM2575T-5 of DUAL 5 andNo.LM2575T-12 of DUAL 12.• INPUT DC POWER 7 - 24VDC• OUTPUT +5V, -5V Common GND, 1A CURRENT inET-MINI PWR DUAL 5• OUTPUT +12V, -12V Common GND, 1A CURRENT inET-MINI PWR DUAL 12• Connector INPUT DC 2PIN PCB TERMINAL SCREWTYPE• Connector OUTPUT DC 3PIN PCB TERMINAL SCREWTYPE• PCB size 4.5 x 5.6 cm.

It is Power Supply in Step-Down Voltage RegulatorCIRCUIT and uses IC NO.LM2575-5. Be able to receiveINPUT DC Power 9-35V to OUTPUT 5VDC. Port INPUTis DC JACK size 2.5mm. and PORT OUTPUT is HEADERMALE and HEADER FEMALE.