Embed Size (px)
DESCRIPTION
Bluetooth setup with KCE-400BT and CDE units
Citation preview
PRODUCTINFORMATION
ALPINE ELECTRONICS (Europe) GmbHQC/Service Department
Address : Wilhelm-Wagenfeld-Str 1-3, 80807 Munich, GermanyPhone : +49 (0) 89 324264-0 FAX : +49 (0) 89 324264-456
Date:
ALPINE ELECTRONICS (Europe) GmbHService/QC Department
Address: Wilhelm-Wagenfeld-Str 1-3, 80807 Munich, GermanyTele: +49 (0) 89 324264 456 FAX : +49 (0) 89 324264-777 456E-mail: [email protected]
KCE-400BT Installation and Setup. Page 1/423.03.2010
CDE-101R-RM/102Ri
Mute-cable:(Pink/Black)
This cable MUST be connected
System cable
KCE-400BT
Connection and Setup for CDE-101R/102Ri + KCE-400BT
AI NETRCAVideoSpeakerSystem Cable (RGB)RemoteMute
PRODUCTINFORMATION
ALPINE ELECTRONICS (Europe) GmbHQC/Service Department
Address : Wilhelm-Wagenfeld-Str 1-3, 80807 Munich, GermanyPhone : +49 (0) 89 324264-0 FAX : +49 (0) 89 324264-456
Date:
ALPINE ELECTRONICS (Europe) GmbHService/QC Department
Address: Wilhelm-Wagenfeld-Str 1-3, 80807 Munich, GermanyTele: +49 (0) 89 324264 456 FAX : +49 (0) 89 324264-777 456E-mail: [email protected]
2. Firstly connect the earth wire of the KCE-400BTthen you can connect the ACC/BATT cables.
3. Now you can connect the KCE-400BT to the headunit with the supplied 13 pin system cable
1. Completely disconnect the head unit from the 12vpower (ACC and BATT).
4. Now connect the Pink/Black mute cable of the 400BTwith the Pink/Black mute cable of the head unit..
NOTE: As soon as the KCE-400BT is connected to BATT it is active and will be visable to other bluetooth devices, this needs to be avoided because the setup is not yet complete, it is better to make sure that there are no active bluetooth devices within range of the KCE-400BT.
Connection and Setup for CDE-101R/102Ri + KCE-400BT
NOTE: The ACC cable of the KCE-400BTshould ONLY be connect to the sameACC supply as the head unit!!!!!!!!!!
To be 100% sure of this it is recommended to connect the ACC cable of the KCE-400BT to the very same cable as the head unit....
5. Make sure there are no active bluetooth devices nearby (see note below) before you connect to 12volts..
KCE-400BT Installation and Setup. Page 2/423.03.2010
AI NETRCAVideoSpeakerSystem Cable (RGB)RemoteMute
PRODUCTINFORMATION
ALPINE ELECTRONICS (Europe) GmbHQC/Service Department
Address : Wilhelm-Wagenfeld-Str 1-3, 80807 Munich, GermanyPhone : +49 (0) 89 324264-0 FAX : +49 (0) 89 324264-456
Date:
ALPINE ELECTRONICS (Europe) GmbHService/QC Department
Address: Wilhelm-Wagenfeld-Str 1-3, 80807 Munich, GermanyTele: +49 (0) 89 324264 456 FAX : +49 (0) 89 324264-777 456E-mail: [email protected]
1. Turn the head unit ON. (If “INTERRUPT”is not shown in the display go to step 3)…
4. Turn the volume knob until the “INT MUTE”is displayed, if this is not found go to step 7.
10. Now remove the nose unit and carry out a“RESET” by pressing the reset switch.Replace the nose unit and turn the headunit ON again. Press and hold the
“FUNC-SETUP” button to get into the setupmenu again.
7. Turn the volume knob until “BT IN” is shown in the display, then press the “ENTER” button.
3. Press and hold the “FUNC-SETUP” button (+2 seconds) to get into the setup menu.
5. If “INT MUTE” is listed, press the “ENTER” buttonto get into the mute setup menu.
6. Turn the volume knob until “MUTE OFF” isdisplayed, now press the “ENTER” button.
9. Turn the volume knob until “BT ADAPTER” is shown in the display then press the “ENTER”button. Use the “RETURN” button to exit thesetup menu.
2. If “INTERRUPT” is shown in the display, disconnect the Pink/black mute cable and carryout steps 3 to 6, then reconnect the mute cable.
8. Now “BT” is “OFF” should be shown in thedisplay (factory setting ).
Connection and Setup for CDE-101R/102Ri + KCE-400BT
KCE-400BT Installation and Setup. Page 3/423.03.2010
PRODUCTINFORMATION
ALPINE ELECTRONICS (Europe) GmbHQC/Service Department
Address : Wilhelm-Wagenfeld-Str 1-3, 80807 Munich, GermanyPhone : +49 (0) 89 324264-0 FAX : +49 (0) 89 324264-456
Date:
ALPINE ELECTRONICS (Europe) GmbHService/QC Department
Address: Wilhelm-Wagenfeld-Str 1-3, 80807 Munich, GermanyTele: +49 (0) 89 324264 456 FAX : +49 (0) 89 324264-777 456E-mail: [email protected]
11. Turn the volume knob and if everything as workedcorrectly after the “BT IN“ entry there should be morebluetooth set entries such as “PAIRED DEV“,
“VISIBLE M“ und CLEAR DEV“.NOTE: If this is not the case carry steps 1 to 10 again!!!
13. Now “PAIRING“ should be shown in the display ofthe KCE-400BT to shown that a connection attemptis being made.
18. Once updating is complete the following optionsshould be available: “PHONE BOOK“,“MISSED CALLS“, “DIALED CALLS“, “RECEIVED CALLS“ (Depending on compatibility)..
14. The “CODE 0000“ will be shown in the display of the head unit, this is the code you have to enter inthe pop up message shown on the phone.
17. Once all the above steps have been successfullycompleted, press the “PHONE“, and “UPDATING“will be displayed, the lenght of time “UPDATING“is displayed varies from phone to phone..
12. Now turn ON the bluetooth feature in the menu ofthe phone you want to connect with the 400BT.
And then carry out the “Search for BT devices“from the BT menu of the phone, KCE-400BTwill be shown in the list given, confirm that youwant to connect to the 400BT.
NOTE: Phone menus can differ from phone to phoneplease check the user manual for your phone!!
15. Once the code is entered (Step 14) the displayof the head unit will show “CONNECTING“
16. When the connection is successfully completed“CONNECTED” will be shown in the display of Head unit.
Connection and Setup for CDE-101R/102Ri + KCE-400BT
KCE-400BT Installation and Setup. Page 4/423.03.2010
