Upload
internet
View
116
Download
5
Tags:
Embed Size (px)
Citation preview
PROJECTS THEMES SUGGESTIONS
2014
Ranque–Hilsch vortex tube:spot cooling device with no moving parts
The vortex tube, also known as the Ranque-Hilsch vortex tube, is a mechanical device that separates a compressed gas into hot and cold streams. It has no moving parts. Vortex tubes have lower efficiency than traditional air conditioning equipment. They are commonly used for inexpensive spot cooling, when compressed air is available.
Ref #1Ref #2
COAXIAL TURBULENT JETS• Turbulent coaxial jets are employed on several industrial processes including
combustion chambers, mixing tanks, cooling systems and premixed burners, for example.
• Project’s objective: compare the numerical results against the experimental jet velocity profiles.
Reference
Drag Reduction in Cylinders• Flow control is a technique that can be used to improve the
efficiency of moving objects by changing the airflow over the boundary surface of the structure’s wall, or the free shear flow.
Reference (1) Watch mythbuster episode car drag reduction
Flow Past Cylinders: Vortex Shedding• Flow over cylindrical bodies shed periodic vortices which change the drag and lift
forces. The fluid-cylinder interaction is relevant to mechanical design of structures (Tacoma mov) and mixing applied to chemical reactors, combustion and in heat transfer equipments.
Reference (1)
See also TG works of Durante 2013 (2) and Panza 2013 (3)
See oscillating cylinder (2)
See elliptical cylinder (5)
See paired cylinders (6)
Pipeline start up of crude oil transport• Oil produced from offshore production platforms can be
transported to the mainland either by oil-tanker. When a tanker is chosen to transport the oil, it is necessary to accumulate oil in some form of storage tank such that the oil tanker is not continuously occupied during oil production, and is only needed once sufficient oil has been produced to fill the tanker.
Semi-SubmersibleW.D. 1650m
FPSOW.D. 1000m
Oil 16 API
12” - 20 km
Pipeline start up• Initial time: the pipeline is full of oil at 4oC. • One has to specify a pump to work with high pressure at low flow
rates at the initial time. • But at steady state the flow rate is high and the pressure is low!
May be OK for Steady State...but not able to reach it
Pipeline start up
• Use CFD to study the pipeline start up and estimate:• The inlet pressure x time for a range of constant flow rates• The heat transfer rate for a range of constant flow rates
• Consider a fixed pressure at the inlet• Determine the inlet volume flow rate with time• Determine how long it takes to get steady state
Carneiro Hidráulico• Veja link no globo rural:
http://g1.globo.com/economia/agronegocios/noticia/2013/06/bomba-de-agua-de-facil-execucao-promete-ajudar-o-produtor-rural.html
• Referencias (1) e (2)
VACU
UM
EJE
CTO
R P
UM
P
A steam ejector is a type of pump that uses the Venturi effect of a converging-diverging nozzle to convert the pressure energy of a motive fluid to velocity energy which creates a low pressure zone that draws in and entrains a suction fluid. After passing through the throat of the injector, the mixed fluid expands and the velocity is reduced which results in recompressing the mixed fluids by converting velocity energy back into pressure energy. The motive fluid may be a liquid, steam or any other gas. The entrained suction fluid may be a gas, a liquid, a slurry, or a dust-laden gas stream. (from wikipedia)
WATCH YOU TUBE MOVIE
Reference (1)
Wave Propagation in an Explosion• Fundamental study in compressible flow. Interesting to investigate
the wall interaction. Also in compressible flow there are the following topics: shock tube and axi-symmetric flow nozzle. (Stadke)
Turbulent B.L. over an Elevation• Fundamental problem applied to atmospheric
phenomena and also to grain transport in form of dunes. (BFC + Turbulent Flow)
http://link.springer.com/article/10.1007%2Fs40430-013-0024-z
Ref (1)Ref (2)Ref (2a)Ref (2b)Ref (3)Ref (4)
Orifice Plates Flow Meter• Orifice plates are used as a flow meter for being simple and relatively
cheap. They are the first option for most industrial applications. Objective of the project is to determine de discharge coefficient using CFD.
Ref (1)Ref (2)
Flow over a Backward-Facing Step• A numerical bench mark solution (in Griebel)
Ref (1)
Ref (2)
Flow in a diffuser for water turbine• The use of diffusers around of the horizontal-axis water turbines have
been widely studied, since the diffuser causes an improvement in the power coefficient of a turbine and are often called Diffuser Augmented Wind Turbines (DAWT’s).
Ref (2)
Flow in a diffuser for a wind turbine• The use of diffusers around of the horizontal-axis wind turbines have
been widely studied, since the diffuser causes an improvement in the power coefficient of a turbine and are often called Diffuser Augmented Wind Turbines (DAWT’s).
Ref (1)
Couette Flow• Turbulence model test. Flow prediction in a channel where one wall
is smooth and the other is rough.
Ref (1)
Deslocamento de ar em túneis devido a passagem de trem.
• A passagem do trem em túneis causa um deslocamento de ar que pode causar um aumento de pressão e arrasto, desconforto para passageiros (trens alta velocidade) e constituir um dos principais mecanismos de renovação de ar em linhas metroviarias (subterrâneas).
• Este tema deverá ser abordado como uma continuação do trabalho desenvolvido pelo Leonardo e Marcelo (2º Sem 2013).
Plate Heat Exchanger & Flow over wavy walls
• Compact heat exchanger composed by parallel plates with groved channels (hering bone) to enhance heat transfer. Applied to the food industry.
Flow over wavy walls
• Separating and attaching regions, friction factor and heat transfer coefficients.
• References: Stony & Vanka (1997); Rabel (2012)
Pressure drop and heat transfer in a compact heat exch.
• friction factor and heat transfer coefficients.• Reference: (1), (2)
FLAT PLATE SOLAR PANNEL
Acesse Thermopedia
• Este tema deverá ser abordado como uma continuação do trabalho desenvolvido pelo Ranyer, Mauro e Cassio (projeto 2º Sem 2013).
SOLAR CHYMNEY TO ENHANCE NATURAL VENTILATION
Veja artigo
Solar Chimney to energy production
• For thermal environmental comfort
• For energy generation
Referências:(1); (2); (3); (4); (5)
• Este tema deverá ser abordado como uma continuação do trabalho desenvolvido pelo Adriano e Felipe (projeto 1º Sem 2013).
Friction factor in pulsatile pipe flow• Pulsating flows appear in various areas of engineering and natural sciences.
They not only play an important role in the operations of IC engines, pumps, nuclear power systems, etc., but are also of immense interest for better understanding of human breathing or blood flow through arteries and hence, have received considerable attention over the years.
Ref (1)Ref (2)Ref (3)
Also of Interest• Automotive:
– flow in manifolds, (see (1))– car aerodynamic,– brake heating,
• Environmental: thermal comfort, pollution dispersion• Hydrodynamic bearings• Flow in ducts:
– T branching flows 3D; – L duct with guiding vanes (BFC); – curved duct: friction and heat transfer (see (1))
1 Estudo da distribuição de ar numa sala (auditório do DE)2 Estudo da distribuição de ar no interior de um veículo3 Determinar o arrasto e sustentação num NACA 0012 – 2D, perfil SELIG 12234 Determinar o arrasto num automóvel, simulação 2D (caminhão, camionete, mini-baja, eco-car,
formula SAE)5 Deslocamento de ar em túneis devido ao deslocamento dos trens. Estudar o aumento no arrasto, o
aumento de pressão.6 Dispersão de gases, transiente.7 Medição de vazão utilizando placas com orifícios.8 Bocal de uma turbina hidráulica tipo Pelton.9 Escoamento compressível sub-sonico e supersonico em um bocal convergente-divergente1 Escoamento num tubo curvo 90.1 Transferência de calor num feixe de tubos: escoamento cruzado em arranjo triangular – comparação
com dados da literatura1 Resfriamento de discos rotativos por jatos de ar – aplicação em freios automotivos1 Transferência de calor num tubo aletado – comparação com dados da literatura.1 Escoamento em bifurcações tipo T – branching flows1 Sustentação e distribuição de ar num Hover-Craft.1 Força num amortecedor hidráulico1 Mancal hidrodinâmico incluindo dissipação térmica1 Chaminé Solar para gerar energia:
http://thefraserdomain.typepad.com/energy/2005/06/about_solar_tow.html1 Escoamento induzido pela corrente de gás que impacta normalmente a uma parede (impinging jet)
( arquivo )2 Escoamento transiente em um canal com superfície livre (tema geral aplicado a imundações de rios e
quebra de barragens) método HOL.2 Velocidade de deslocamento de uma bolha alongada dentro de uma tubulação preenchida com
líquido, HOL.2 Escoamento de óleo com resfriamento. Problema de relaminarização e pico de pressão. (veja
arquivo)
THESE ARE PROJECTS’ THEMES ALREADY DONE BY PREVIOUS YEAR STUDENTS OR IN I.C. AND OR T.G.
THEMES NO LONGER AVAILIABLE
Thermal conduction in composite materials
COMMONLY USED POLYMER materials such as polyethylene (PE), polypropylene (PP), polyvinyl chloride (PVC) or polyamide are good electrical and thermal insulators. Recent applications of polymers as heat sinks in electronic packaging require new composites with relatively high thermal conductivity. Improved thermal conductivity in polymers may be achieved either by molecular orientation or by the addition of conductive fillers.
Supersonic Nozzle
The purpose of this project is to simulate the operation of a converging-diverging nozzle, perhaps the most important and basic piece of engineering hardware associated with propulsion and the high speed flow of gases. This device was invented by Carl de Laval toward the end of the l9th century and is thus often referred to as the 'de Laval' nozzle. This project explores the compressible aerodynamics assessing the flow through this type of nozzle at a range of conditions.
Shark-skin Drag Reduction (Turbulence)
• See review work of BRIAN DEAN AND BHARAT BHUSHAN• Also visit:
http://www.csi.tu-darmstadt.de/institute/dcc/forschung_7/skinfriction/index.en.jsp
Flow in the Wake of a Taylor Bubble• Study of slug flow has application in oil production. The flow in the
wake is still poorly understood. The knowledge on the wake flow allow the development of accurate pressure drop model. Objective: model the wake flow numerically.
Design of a flush film height sensor • Using a conduction heat transfer analog design a capacitive sensor
capable to measure liquid film height. The sensor consists of two parallel strips of metal flush to the wall.
Coney – conductance probe
Ceccio – conductance probe
Turbulent Jet Impinging• Turbulent jets impinging onto a rough surface are a simple and effective means
of promoting the heating or cooling of surfaces. In fact, the number of applications an impinging jet encounters in nature and technology is impressively high. The vertical take-off of aircrafts, the cooling of electronic instruments and the tempering and shaping of glass name only a few of numerous applications.