Upload
duongthuy
View
249
Download
0
Embed Size (px)
Citation preview
PumPs and accessories 2016 catalog
not all irrigation products are listed. if you are looking for something you don’t see, please ask!3 stocked at most stores * mTi Best sellers . . . Best availability
Prices subject to change without notice.
accessories
PumPs
and
Berkeley “B” series Pumps (Inquire for proper pump sizing)MTI Part Number Description
B1WPS-3 3HP, 1PH, 230V Pump, can wire tri-voltage 208/230V/360 3* B1WPS-5 5HP, 1PH, 230V Pump, can wire tri-voltage 208/230V/360
B1WPS-71/2 7 1/2 HP, 1PH, 230V Pump, can wire tri-voltage 208/230V/360
B2TPMS-3-S 3HP, 1PH, 230V Pump B2TPMS-5 5HP, 1PH, 230V Pump
B82456-01 2HP, 1PH, Centrifugal Self-priming Pump, SSHM-2 See chart on page 125 of the catalog
Note: Amp ratings for pumps are on the next few pages.
www.berkeleypumps.com
Berkeley Replacement PartsMTI Part Number Description
3 BKS05126 Gasket for most B Series Pumps BKS07445 C Series Gasket
BKS32014 Seal, Mechanical Shaft BKS32015 Seal, Mechanical Shaft
NOTE: We offer a full line of Berkley pumps for special order situations.
Flint and Walling PumpsMTI Part Number Description
High Pressure Pumps - Lake Systems FWCJ101-3/4 F & W 3/4 HP, 115/230V, 1 PH Cent Pump** 3* FWCJ101-10 F & W 1HP, 115/230V, 1PH Cent Pump**
FWCJ101-15 F & W 11⁄2 HP, 115/230V, 1PH Cent Pump** FWCJ101-20 F & W 2HP, 115/230V, 1PH Cent Pump**
FWCJ101-23S F & W 2HP, 1PH, 3-Stage Pump** FWCJ101-30 F & W 3HP, 1PH, 230V, 3-Stage Pump** Booster Pumps
FWCJ103-1/3 F & W 1/3 HP, 115/230,V 1PH Pump** FWCJ103-05 F & W 1/2 HP, 115/230V, 1PH Pump** FWCJ103-3/4 F & W 3/4 HP, 115/230V, 1PH Pump**
3* FWCJ103-10 F & W 1HP, 115/230V, 1PH Pump** FWCJ103-15 F & W 11⁄2 HP, 115/230V, 1PH Pump**
3 FWCJ103-20 F & W 2 HP, 115/230V, 1PH Pump** ** 1 1/2" suction, 1 1/4" discharge.
3* FWEKO5S-1/2 F & W 1/2 HP, Jet Pump, 1 1/4" suction, 3/4" discharge
MTI Part Number Description 3 FW-130968 Gasket for 3/4–2 HP F & W Pump
FW-135279A Shaft, CJ101, 3/4 HP–2 HP, 2-Stage Pump Impeller for 1 HP CJ101 Impeller for 11⁄2 HP CJ101
FW-135281A FW-126900A FW-126901A Impeller for 2 HP CJ101
3 FW-131239B Int. Stage for 3/4–2 HP CJ101 3 FW-131100 Rotary Seal for 3/4–2 HP CJ101 Note: For pump wire sizing, see Technical Data, section 22.
www.flintandwalling.com
Pressure relief Valve by WattsMTI Part Number Description WA05Bp45-100 1/2" Pressure Relief 45–100 psi
Note: See picture on next page.
www.watts.com
“B” Series Pump
B82456
CJ101
CJ103
“EK” Series 1/2 HPShallow Well Jet Pump
Pressure Relief Valve
Performance curves may be found on the following pages.
▲▲
▲
33
333
3
Flint and Walling Repair Parts
18
PUMPS AND ACCESSORIES 2016 Catalog
Burnsville, mn maple Grove, mn Fargo, nd Grimes, ia Berkeley, mo763-592-5701 763-592-5703 701-365-4260 515-661-6800 314-506-4100
accessories
PumPs
and
WA05BP45-100
KF101
18
not all irrigation products are listed. if you are looking for something you don’t see, please ask!3 stocked at most stores * mTi Best sellers . . . Best availability
Prices subject to change without notice.
accessories
PumPs
and
suction Lift installation• Pipingrunandconnectionfittingsshouldbeproperly
aligned and independently supported to reduce strain on pump case.
• Suctionpipesizeshouldbeatleastonecommercialpipe size larger than opening of pump inlet. Flowvelocity should not exceed 8 ft./sec.
• Suctionscreenmustscreenoutsolidsthatcouldclog pump impeller.
• Suctionscreenareamustbeatleastfourtimessuction pipe area.
• Allsuctionpipingmusthaveacontinuousrisetothepump suction inlet. A 1/4 inch per foot minimumslope is recommended.
motor data
PUMPS AND ACCESSORIES 2016 Catalog
18
SSHM-2 PERFORMANCE at 3,450 RPM
Pump Performance curves
Berkeley ssHm-2 self-Priming,High-Pressure Performance230V single Phasesuction: 1 1/2" • Discharge: 1 1/4"Weight: 95 lbs. B82456
accessories
PumPs
and
230V 1 PHASE SELF PRIMING CONVENIENCE AND HIGH-PRESSURE PERFORMANCEThe Berkeley SSHM-2 Self-Priming Pump delivers high-pressure performance without priming problems and delays. Designed for minimal electrical consumption and quiet operation, the SSHM-2 meets the high-flow and high-pressure challenges of the most demanding applications.
SSHM-2 Design FeaturesSelf-Priming Design Once initially primed, the SSHM-2 will automatically re-prime cycle after cycle.Cast-Iron Motor Bracket & 11⁄4" NPT discharge connection, stable heavy-duty designIntegral Pedestal for rigid pipe connections and base mounting.Cast-iron Suction Flange 11⁄2" NPT suction connection, heavy-duty durable cast-iron suction bracket.Outer Shell Polished 304 stainless steel.Noryl® Impellers & Diffusers Precision molded extra-smooth ports to maximize efficiency and performance.Shaft 303 stainless steel.Mechanical Seal High-pressure seal, carbon-ceramic seal faces, Buna-N elastomers.Priming Valve Special brass priming valve, patented for trouble-free operation during the priming cycle.A. O. Smith Motor 2HP, 3450 rpm, 230 volt, high-service factor open drip-proof motor, suitable for continuous duty operation.
Includes auto reset.
Note: One-year warranty for defects from date of installation.
REPAIR PARTS LIST Key No. No. Part Description Used B82456 1 Motor 1 B85740
2 Socket Head Capscrew 4 U30-104ZP
3 Slinger 1 17351-0009
4 Bracket 1 M13784
5 Impeller Repair Kit 1 B85604(includes Key Nos. 6–8 and 10–14)
6 Shaft Seal* 1 U9-6
7 Spacer 1 121P1710
8 O-Ring 2 111P2700
9 Sleeve 1 251A4310
10 Diffuser 4 101P4790
11 Impeller 4 101P2070
12 Washer, Flat 1 121P1760
13 Washer, Toothed 5 M13975
14 Impeller Nut 1 U36-204SSW
15 Pump Body (Suction) 1 751S4800
16 Washer 2 121P0810
17 Pipe Plug 2 171P1180
18 Capscrew 4 121P1690
19 Recirculation Valve Complete 1 ZBR05820 (includes O-Ring)
*To order shaft seal as a separate part, order Part No. U109-6A.
REPAIR PARTS
PUMPS AND ACCESSORIES 2016 Catalog
Burnsville, mn maple Grove, mn Fargo, nd Grimes, ia Berkeley, mo763-592-5701 763-592-5703 701-365-4260 515-661-6800 314-506-4100
18
not all irrigation products are listed. if you are looking for something you don’t see, please ask!3 stocked at most stores * mTi Best sellers . . . Best availability
Prices subject to change without notice.
accessories
PumPs
and
Note: We also carry centrifugal pumps for Golf Course Applications such as 20, 30, 40, or 60 HP. Call for more information.
Note: Pump can be used as a booster and a centrifugal.
Full Load amp ratings for single-Phase and Three-Phase motorsThis is only a guide to be used when actual full-load current is not listed on the motor faceplate.
Single Phase Three PhaseHorsepower 120 Volt 230 Volt 230 Volt 460 Volt3 34 amps 17 amps 9.6 amps 4.8 amps5 55 amps 28 amps 15.2 amps 7.6 amps7 1/2 80 amps 40 amps 22 amps 11 amps10 100 amps 50 amps 26 amps 14 amps15 42 amps 21 amps
Pump Performance curves
Berkeley Type “B” rating curvesTypical curve for B1WPs
suction: 1 1/2" • Discharge: 1"
PUMPS AND ACCESSORIES 2016 Catalog
18
Pump Performance curves
Berkeley Type “B” rating curvesTypical curve for B2TPms
suction: 2 1/2" • Discharge: 2"
accessories
PumPs
and
Note: Pump can be used as a booster and a centrifugal.
Full Load amp ratings for single-Phase and Three-Phase motorsThis is only a guide to be used when actual full-load current is not listed on the motor faceplate.
Single Phase Three PhaseHorsepower 120 Volt 230 Volt 230 Volt 460 Volt3 34 amps 17 amps 9.6 amps 4.8 amps5 55 amps 28 amps 15.2 amps 7.6 amps7 1/2 80 amps 40 amps 22 amps 11 amps10 100 amps 50 amps 26 amps 14 amps15 42 amps 21 amps
PUMPS AND ACCESSORIES 2016 Catalog
Burnsville, mn maple Grove, mn Fargo, nd Grimes, ia Berkeley, mo763-592-5701 763-592-5703 701-365-4260 515-661-6800 314-506-4100
18
not all irrigation products are listed. if you are looking for something you don’t see, please ask!3 stocked at most stores * mTi Best sellers . . . Best availability
Prices subject to change without notice.
accessories
PumPs
and
Pump Performance curves
Berkeley Type “c” rating curvesTypical curve for c2mPs
suction: 2 1/2" • Discharge: 2"
Full Load amp ratings for single-Phase and Three-Phase motorsThis is only a guide to be used when actual full-load current is not listed on the motor faceplate.
Single Phase Three PhaseHorsepower 120 Volt 230 Volt 230 Volt 460 Volt3 34 amps 17 amps 9.6 amps 4.8 amps5 55 amps 28 amps 15.2 amps 7.6 amps7 1/2 80 amps 40 amps 22 amps 11 amps10 100 amps 50 amps 26 amps 14 amps15 42 amps 21 amps
PUMPS AND ACCESSORIES 2016 Catalog
18
Pump Performance curves for the Brass impeller modelsFlint and Walling Pump (High Pressure) for Lake systems
cJ101 series rating curves
CJ101 Brass Impellers
To Figure Total Head in Feet:
Take the Pressure required to run system
(Multiply by) x 2.31
(add) + vertical lift,
(add) + friction loss in worst zone
= Total Head in Feet
To Convert from Total Headin Feet to P.S.I.:
Take Head in Feet x .433 = P.S.I.
accessories
PumPs
and
Single Phase Three PhaseHorsepower 115/230 Volt 208–230/460 Volt3/4 14.0/7.0 amps 3.5/1.75 amps1 18.0/9.0 amps 4.5/2.25 amps1 1/2 21.00/10.5 amps 5.7/2.85 amps2 25.00/12.5 amps 7.4/3.7 amps3 –/13.5 amps 9.8/4.9 amps
Flint and Walling Pumpmax amp chartsThis is only a guide to be used when actual full-load current is not listed on the motor faceplate.
www.flintandwalling.com/ProductBenefit.aspx?ProductID=110
▲
Tota
l Hea
d
39 34 29 21 5 38 33 26 18 31 29 23 12 42 38 33 26 18 40 36 31 24 14 32 31 28 21 48 44 39 34 27 17 44 42 37 31 24 10 34 33 32 29 20 56 52 47 41 34 24 50 49 45 39 31 19 37 36 35 34 27 49 47 43 40 36 32 28 22 12 45 44 42 39 35 31 26 19 35 34 33 32 31 29 23 15 56 54 51 48 44 39 33 27 18 50 49 48 46 42 37 31 24 37 36 36 35 34 33 29 20
MTI PartNumber1 Phase
SuctionLift ft.
10 20 30 40 50 60 70 80 90
Capacity U.S. GPM
Discharge Pressure PSI
Manufacturer Model No.
FWCJ101-3/4
FWCJ101-1O
FWCJ101-15
FWCJ101-20
FWCJ101-23S
FWCJ101-30
CJ101B071
CJ101B101
CJ101B151
CJ101B201
CJ101C201
CJ101C301
CJ101B073
CJ101B103
CJ101B153
CJ101B203
CJ101C203
CJ101C303
1 Phase 3 PhaseHP Stages
3/4
1
11⁄2
2
2
3
2
2
2
2
3
3
54
62
69
70
98
95
160 psig
160 psig
160 psig
160 psig
160 psig
160 psig
200ºF
200ºF
200ºF
200ºF
200ºF
200ºF
515255
15255
15255
15255
15255
1525
Max.Press.
PSI
Max.CasePress.
Max.LiquidTemp.
To convert to feet of head, multiply by 2.31. Do not exceed the maximum case pressure and maximum liquid temperature rating of the pump. Suction & Discharge Tapping: 1 1/2" x 1 1/4"Motor Voltage: Single Phase: 1/3 HP – 115 V; 1/2 thru 2 HP – 115-230 V; 3 HP – 230 V, 60 HZ
Three Phase: 1/2 thru 3 HP – 208-230/460 V, 50/60 HZ
PUMPS AND ACCESSORIES 2016 Catalog
Burnsville, mn maple Grove, mn Fargo, nd Grimes, ia Berkeley, mo763-592-5701 763-592-5703 701-365-4260 515-661-6800 314-506-4100
18
not all irrigation products are listed. if you are looking for something you don’t see, please ask!3 stocked at most stores * mTi Best sellers . . . Best availability
Prices subject to change without notice.
accessories
PumPs
and
centrifugal Pump repair Parts–cJ101 series
Note: Old style gasket beforesquare cut ring FW139123.
HP 3/4 1 1 1/2 2 2 3STAGE 2 2 2 2 3 3
CJ101B071 CJ101B101 CJ101B151 CJ101B201 CJ101C201 CJ101C301
CJ101B073 CJ101B103 CJ101B153 CJ101B203 CJ101C203 CJ101C303
CJ101P071 CJ101P101 CJ101P151 CJ101P201 CJ101D201 CJ101D301
CJ101P073 CJ101P103 CJ101P153 CJ101P203 CJ101D203 CJ101D303
1 Motor, Nema J - 1 PH 98J107 98J110 98J115 98J120 98J120 98J6301 Motor, Nema J - 3 PH 98J307 98J310 98J315 98J320 98J320 98J330
Motor Access Cover w/screws 021301R 1 1 1 1 1 1‡ Screws only, Access Cover 021302 2 2 2 2 2 2
‡ Slinger Washer 126905 1 1 1 1 1 1 2 Shaft 135279A 135279A 135279A 135279A 136612A 136612A 3 Mounting Ring 125204 1 1 1 1 1 1 4 Hex Hd. Cap Screws 3/8 x 3/4" * 2 2 2 2 2 2
5 Seal, Rotary w/ Spring 131100 1 1 1 1 1 16 Impeller - Brass †135280A †135281A †126900A †126901A †139126A †136951A6 Impeller - Thermoplastic †133425 †133427 †139180 †128472 †139221 †139104
7 Spacer, Shaft 133380 1 1 1 1 2 2 8 Gasket 130968 2 2 2 2 3 3 9 Intermediate Stage Assembly** 131239B 1 1 1 1 2 2
‡ Suction Clearance Ring 130957 1 1 1 1 2 2‡ Hub Clearance Ring 131282 1 1 1 1 2 2‡ Square Cut Ring Interm. Stg. 020240 1 1 1 1 2 210 Suction Flange Assembly 125227A 1 1 1 1 1 1‡ Suction Clearance Ring 130957 1 1 1 1 1 1‡ Suction Bearing 020053 1 1 1 1 1 111 Pump thru Bolts 3/8 x 3-1/4" * 4 4 4 4 -- --11 Pump thru Bolts 3/8 x 5" -- -- -- -- 4 412 Base w/ Bolts 3/8 x 1-1/4" 020054 1 1 1 1 1 1
13 1/4" NPT Plug * 4 4 4 4 4 4* Standard hardware item † For quantity required, see number of stages‡ Not shown **Includes two castings, square cut ring, suction and hub clearance ring. See detail drawing.( ) Kit includes: Access cover, screws and wiring diagrams
SINGLE PHASEBRASS IMPELLER
THREE PHASEBRASS IMPELLER
SINGLE PHASEPLASTIC IMPELLER
THREE PHASEPLASTIC IMPELLER
DESCRIPTION
MODELNO.
PART NO. QUANTITY
ITEM
PUMPS AND ACCESSORIES 2016 Catalog
18
Flint and Walling Pump (Booster Pump)cJ103 series rating curves
Pump Performance curves for the Brass impeller models
CJ103 Brass Impellers
To Figure Total Head in Feet:
Take the Pressure required to run system
(Multiply by) x 2.31
(add) + vertical lift,
(add) + friction loss in worst zone
= Total Head in Feet
To Convert from Total Headin Feet to P.S.I.:
Take Head in Feet x .433 = P.S.I.
accessories
PumPs
and
Single Phase Three PhaseHorsepower 115/230 Volt 208–230/460 Volt1/3 8.6/4.3 amps –/– amps1/2 13.0/6.5 amps 3.5/1.75 amps3/4 14.0/7.0 amps 3.5/1.75 amps1 18.0/9.0 amps 4.5/2.25 amps1 1/2 21.0/10.5 amps 5.7/2.85 amps2 25.0/12.5 amps 7.4/3.7 amps
Flint and Walling Pumpmax amp chartsThis is only a guide to be used when actual full-load current is not listed on the motor faceplate.
www.flintandwalling.com/ProductBenefit.aspx?ProductID=111
▲
42 34 21 36 26 28 50 47 37 25 43 40 29 9 33 30 15 71 62 51 36 11 66 54 40 19 57 43 25 76 69 61 50 36 16 73 65 54 41 24 66 57 45 29 94 88 80 70 59 44 18 92 85 75 63 49 27 74 72 66 52 34 109 103 96 86 75 61 39 109 103 94 82 67 45 90 89 85 71 51
MTI PartNumber1 Phase
SuctionLift ft.
10 15 20 25 30 35 40 45 50
Capacity U.S. GPM
Discharge Pressure PSI
Manufacturer Model No.
FWCJ103-1/3
FWCJ103-05
FWCJ103-3/4
FWCJ103-10
FWCJ103-15
FWCJ103-20
CJ103031
CJ103051
CJ103071
CJ103101
CJ103151
CJ103201
CJ103053
CJ103073
CJ103103
CJ103153
CJ103203
1 Phase 3 PhaseHP Stages
1/3
1/2
3/4
1
11⁄2
2
1
1
1
1
1
1
27
32
32
39
43
44
100 psig
100 psig
100 psig
100 psig
100 psig
100 psig
200ºF
200ºF
200ºF
200ºF
200ºF
200ºF
515255
15255
15255
15255
15255
1525
Max.Press.
PSI
Max.CasePress.
Max.LiquidTemp.
To convert to feet of head, multiply by 2.31. Do not exceed the maximum case pressure and maximum liquid temperature rating of the pump. Suction & Discharge Tapping: 1 1/2" x 1 1/4"Motor Voltage: Single Phase: 1/3 HP – 115 V; 1/2 thru 2 HP – 115-230 V; 3 HP – 230 V, 60 HZ
Three phase: 1/2 thru 3 HP – 208-230/460 V, 50/60 HZ
PUMPS AND ACCESSORIES 2016 Catalog
Burnsville, mn maple Grove, mn Fargo, nd Grimes, ia Berkeley, mo763-592-5701 763-592-5703 701-365-4260 515-661-6800 314-506-4100
18
not all irrigation products are listed. if you are looking for something you don’t see, please ask!3 stocked at most stores * mTi Best sellers . . . Best availability
Prices subject to change without notice.
accessories
PumPs
and
Centrifugal Pump repair Parts–cJ103 series, Booster Pump
HP 1/3 1/2 3/4 1 1 1/2 2STAGE 1 1 1 1 1 1
CJ103031 CJ103051 CJ103071 CJ103101 CJ103151 CJ103201
CJ103053 CJ103073 CJ103103 CJ103153 CJ103203
CJ103P031 CJ103P051 CJ103P071 CJ103P101 CJ103P151 CJ103P201
CJ103P053 CJ103P073 CJ103P103 CJ103P153 CJ103P203
1 Motor, Nema J - 1 PH 98J103 98J105 98J107 98J110 98J115 98J1201 Motor, Nema J - 3 PH -- 98J305 98J307 98J310 98J315 98J320
Motor Access Cover 021301R 1 1 1 1 1 1 Screws, Access Cover 021302 2 2 2 2 2 2
‡ Slinger Washer 126905 1 1 1 1 1 1 2 Mounting Ring 134107 1 1 1 1 1 1 3 Hex Hd. Cap Screws 3/8 x 3/4" * 4 4 4 4 4 4
4 Seal, Rotary w/ Spring 131100 1 1 1 1 1 15 Impeller - Brass 130403A 126900A 127805 127804 127806 127848
5A Impeller - Plastic 133426 139222 021280 135248 021279 N/A5B Clearance Ring N/A 138138 134240 134240 134240 N/A6 Ring, Square Cut † 132583 1 1 1 1 1 1
7 Body Assembly-Brass Impeller 127870 127870 127780 127780 127780 127780 Body Assembly-Plastic Impeller 021439 1 1 1 1 1 1
‡ Suction Clearance Ring-Brass 127869A 127869A N/A N/A N/A N/A8 Pipe Plugs, 1/8" NPT * 4 4 4 4 4 49 Hex Hd. Cap Screws 3/8 x 1" * 4 4 4 4 4 4
10 Base 125855 1 1 1 1 1 1* Standard hardware item‡ Not shown† For pumps with paper gasket, replace with part number 127782( ) Kit includes: Access cover, screws and wiring diagrams
SINGLE PHASEBRASS IMPELLER
THREE PHASEBRASS IMPELLER
SINGLE PHASEPLASTIC IMPELLER
THREE PHASEPLASTIC IMPELLER
DESCRIPTION
MODELNO.
PART NO. QUANTITY
ITEM
PUMPS AND ACCESSORIES 2016 Catalog
18
Pump Performance curves
Flint and Walling PumpFWeK05s-1/2
1/2 HP motor rating curves“EL” 1/2 HP Shallow Well Capacities
PSI B
oost
GPMPump Rated at 5’ Suction Lift
74 PSIShut-Off
MTI Part Model #/ Suction Number Voltage Lift Ft.
accessories
PumPs
and
Float switchMTI Part Number Description
UE1OMWE-NO** Normally open single float. Float control switch, when water level rises too much,it shuts off the pump.
UE1OMWE-NC Normally closed, single float. When water level drops, it shuts the pump off.
3
20–40 401-1/4" x 3/4"60FWEK055-1/2
5 10.5 9.5 5.8 4.0
15 7.6 7.3 4.5 2.5
25 4.5 4.2 3.5 2.0
EK05S115/230V
1/2 HP
Includes: Pump, Motor, Shallow Well Ejector and Pressure Switch, Factory Preset at 30/50 PSI.
PumpShippingWeight
PressureSwitchSetting
Suction &Discharge
Shut-OffPress. @
0 lift (PSI)?
Capacities GPM at Discharge Pressure PSIG
20 30 40 50
PUMPS AND ACCESSORIES 2016 Catalog
Burnsville, mn maple Grove, mn Fargo, nd Grimes, ia Berkeley, mo763-592-5701 763-592-5703 701-365-4260 515-661-6800 314-506-4100
18
*UE1017670 Double float master switch, w/o cord, lead free. Includes bothof the above switches.
UE1017670Double Float Master Switch ** Discontinued when inventory is depleted, contains Mercury that is not allowed in Minnesota.
not all irrigation products are listed. if you are looking for something you don’t see, please ask!3 stocked at most stores * mTi Best sellers . . . Best availability
Prices subject to change without notice.
accessories
PumPs
and
Foot Valves/check ValvesMTI Part Number Description
FV15 1 1/2" Check Valve FV2 2" Check Valve 3 FV6 1 1/2" Foot Valve 3* FV8 2" Foot Valve 3 FV8105 2" Foot Valve O-Ring 3 FV8104 1 1/2" Foot Valve O-Ring PFV8 2" Plastic Foot Valve Additional parts available on request.
Big Foot FiltersMTI Part Number Description
BF-40GFILTER 40-Gallon Irrigation Filter BF-40GSTAND Stand for 40-Gallon Irrigation Filter BF-80GFILTER 80-Gallon Irrigation Filter
www.bigfootmfg.com/filter_stand.html
sure-Flo Foot ValvesMTI Part Number Description
SFVV3FP 3" Threaded Vertical Foot Valve SFVV4FP 4" Threaded Vertical Foot Valve SFVV6FP 6" Threaded Vertical Foot Valve
VFG3A 3" Flapper and Gasket Assembly VFG6A 6" Flapper and Gasket Assembly
VFG8A 8" Flapper and Gasket Assembly VFG10 10" Flapper and Gasket Assembly
NOTE: Other configurations available.
www.sure-flo.com/prod_layout.asp?part=SFVVFP
eccentric reducersMTI Part Number Description
GN2X15TECC 2" x 1 1/2" BK Thd ECC Reducer GN3X2TECC 3" x 2" BK Thd ECC Reducer GN3X25TECC 3" x 2 1/2" BK Thd ECC Reducer GN4X2TECC 4" x 2" BK Thd ECC Reducer GN4X25TECC 4" x 2 1/2" BK Thd ECC Reducer GN4X3TECC 4" x 3" BK Thd ECC Reducer
Kleen-Flo Filters by northern WireMTI Part Number Description
3* KF100 Kleen-Flo Filter (KF15F) 3* KF101 Kleen-Flo Replacement Screen (KFRS) 3 KFAQF Algae Queen Filter, up to 80 gpm each
sea sled, Lake Basket sledMTI Part Number Description
3 KG4000 Sea Sled, Lake Basket Sled
Pressure GaugesMTI Part Number Description
3 AM0-100 Gauge 0–100 PSI AM0-200 Gauge 0–200 PSI AM0-200L Gauge 0–200 (Liquid Filled)
All bronze foot valve with heavy perforated solid brass strainer.
Big Foot Filters
Sure-Flo Foot Valve
Installs quickly; minimum maintenance with rust-protected cylindrical metal cage, screen of fine mesh flexible fiberglass,
replaceable in minutes at low cost, 9 x 28"; up to 6,000 gallons per hour.
Note: 2" galvanized MPT connection
Gauge
▲▲
PUMPS AND ACCESSORIES 2016 Catalog
18
PumpsFull Load Amps
Adjustable Range
Single Phase230 Volt1800/3600 RPM
3 HP 16/16.5 Amps5 HP 24/28 Amps7 1/2 HP 35.2/36.5 Amps10 HP 44/46.7 Amps
Three Phase230 Volt1800/3600 RPM
3 HP 8.4/8.9 Amps5HP 14/14.7 Amps7 1/2 HP 19/21 Amps10 HP 25/28 Amps
NOTE: You can use a 3-phase starter for a single phase.
NOTE: For pump Direct Bury power cable, see technical data.
K-Rain Coil Specifications24 VAC, 60 HzInrush: 60 VASealed: 7 VA, 2.3 WATTSResistance: (±10%): 5.61 OHMSDouble Pole, Single ThrowInductive: 40 AMPResistive: 50 AMPInput: 120 VAC - up to 5 H.P.240 VAC - up to 7.5 H.P.
K-Rain Pump Start Relay
accessories
PumPs
and
Pump startersMTI Part Number Description
3 K-R1552 24V, 60 HZ, 120 VAC–up to 5 HP, 240 VAC–up to 7 HP
The pump start relay enclosure is constructed with a corrosion-resistant, UV resistant and shockproof material. The rain-tight, secure, rustproof enclosure provides a safe and secure connection in a housing built to last. Operation: Pump start relays are U.L. rated and available to operate 2 HP up to 7.5 HP pumps. Dimensions: Height–7", Width–5", Depth–45⁄8"NOTE: For pumps under 2 hp, see IR-SR1 on pages 52 and 136.
General electric Pump startersNOTE: Furnas brand is no longer available, but we can convert to GE. New starters are being sized by full load amps and new starters have adjustable amp reset. Because of the discontinuation of certain size starters/contactors, we are currently using General Electric C-2000 assembled starters, NEMA 1
adjustable solid state starters with overload protection
Size by Amp and Voltage
Single Phase 230V Coil Trip Range GE LAC25A1WTA1AA 3 HP, 16/16.5 amps 24V 17.5–22 A GE LAC04A1WVA1AA 5 HP, 24/28 amps 24V 25–32 A GE LAC06AJWEA1AA 7.5 HP, 36.5/35.2 amps 120V* 30–43 A GE LAC06AJWGA1AA 10 HP, 46.7/44 amps 120V* 42–55 A
Three Phase 230V Coil Trip Range GE LACOOA1WNA1AA 3 HP, 8.4/8.9 amps 24V 8–12.2 A GE LAC02A1WSA1AA 5 HP, 14/14.7 amps 24V 14.5–18 A GE LAC04A1WUA1AA 7.5 HP, 19/21 amps 24V 21–26 A
GE LAC04A1WVA1AA 10 HP, 25/28 amps 24V 25–32 A
Units with 24V Coil wire direct to pump start and common in the controller.*Units with 120V Coil require a Potter-Brumfield Relay - see diagram with relay below.*Starters not rated for 460V. Call MTI to have one sized.
Pressure switch by allen BradleyMTI Part Number Description
UE836-C7 Pressure Switch
relays by Potter-BrumfieldMTI Part Number Description
3 NE8PINSOC 8 Pin-In Socket 3 NE24VREL 24V Relay
Potter & Brumfield relays feature multi-contact arrangement: octal plug termination; clear dust cover. Shown: 24V Relay NE24REL.
NOTE: Use with 120V Coil Starters.
Use #6 and #1 terminals for 120V wires.Use #2 and #7 terminals for 24V wires.
2 1 8 7
3 4 5 6
NE8pinsoc
PUMPS AND ACCESSORIES 2016 Catalog
Burnsville, mn maple Grove, mn Fargo, nd Grimes, ia Berkeley, mo763-592-5701 763-592-5703 701-365-4260 515-661-6800 314-506-4100
18
not all irrigation products are listed. if you are looking for something you don’t see, please ask!3 stocked at most stores * mTi Best sellers . . . Best availability
Prices subject to change without notice.
accessories
PumPs
and
Caution: The relay is to control up to a 2 HP motor only. Do not attach to larger commercial units, or exceed the contact ratings as shown.
MAXIMUM RATINGS:
Contacts rated:1 HP at 120VAC 1 Phase2 HP at 250VAC 1 Phase
Coil rating:24VAC, 3VA
Operating req:Min. 19VACMax. 30VAC
CAUTION: When using electronic controllers:1) Relay should be mounted with a 5 foot minimum space between itself and the controller2) Controller should be 12 feet from the pump3) Controller should be on a separate power source than the pump
IF THESE STEPS ARE NOT TAKEN, MALFUNCTIONS
MAY OCCUR!
Choose a location along the pipe where 10 pipe diameters upstream and five pipe diameters downstream of the sensor provide no flow disturbance. Pipe bends, valves other fittings, pipe enlargements and reductions should not be present in this length of pipe.
• Exhaustfan• Microprocessor• Easeofinstallation• Easeofmaintenance
• Oneyearlimitedwarranty
Call for more informationand pricing.
irritrol Pump start relay
MTI Part Number Description
3 IR-SR1 Pump Start Relay NOTE: For pumps 2–7 1⁄2 hp see K-R1552 Relay on page 135.
Toro Flow sensorMTI Part Number Description
TFS-050 Flow Sensor, 1/2", Plastic Tee (Sch 40 PVC), 1.2–12 GPM TFS-075 Flow Sensor, 3/4", Plastic Tee (Sch 40 PVC), 2.7–28 GPM TFS-100 Flow Sensor, 1", Plastic Tee (Sch 40 PVC), 5–50 GPM TFS-150 Flow Sensor, 1.5", Plastic Tee (Sch 80 PVC), 5–100 GPM TFS-200 Flow Sensor, 2", Plastic Tee (Sch 80 PVC), 10–200 GPM TFS-300 Flow Sensor, 3", Plastic Tee (Sch 80 PVC), 20–300 GPM TFS-400 Flow Sensor, 4", Plastic Tee (Sch 80 PVC), 40–500 GPM WT32-002-090 Sensor Cable, 2-Cond., Shielded, Sold by the foot
Toro Compatibility Other CompatibilityTMC-424 Irritrol MC-ETIS-360/480 Rain Master®
SentinelTM Hunter® ACCSitePro® WeatherTRAK® ET Pro2TM
Calsense®
Rain Bird Maxicom2, MDC & SiteControl Note: Flow sensor valves also listed in section 1.
FloBoy Pumping system
This station is for residential, commercial, athletic turf and small golf course irrigation applications. It’s designed for ease of installation and maintenance.
FloBoy is a self-contained, one pump system that can be purchased with City Water Boost or Suction Lift configurations. The pump and controls are housed in a steel box with a lockable, lift-up door. The micro processor panel has low pressure and high pump temperature safeties. The panel starts the pump on a pressure drop and stops it on flow. The steel box also houses the pump starter and overloads for the motor. On the outside of the box is a fused main disconnect switch with fusing and lightning arrestor for the pump motor.
Standard features include:• MotorSizesupto30HP• 3Phase(230/460volt)upto30HP• 1Phase(230volt)upto10HP• Capacityto250GPM• Isolationandcheckvalves
PUMPS AND ACCESSORIES 2016 Catalog
18
Visit their Web site:www.americanhydro.com
Fertile earth™
The Fertile earth ProFeeder makes landscape improvement simple.
The ProFeeder is a precision liquid injection system that automatically delivers the most advanced landscape products through your sprinklers as you water. The unique design eliminates the need for cumbersome and difficult to use tanks. Once installed, simply grab a bottle of Liquid Life plant food, Nature Shield, or Fertile Earth.
• Installsinastandardvalvebox• Auto-regulatingdesign• Waterpressure:25–125psi• Waterflow:1.5–30GPM• Easytoserviceandrepair• Workswithdrip,pop-uporimpact
installed in the same system
Fertile earth™ ProFeederMTI Part Number Description
3 P1X ProFeeder, adapts to ProFeeder Formula bottles
For low flow situations, with new feeder, use the white nozzle.
P1X-LF ProFeeder, Low Flow, .5 to 20 gpm** 3 P1X-5G Feeder w/5-gallon tank, no valve box
P1X-ETC5G ProFeeder w/5-gallon tank w/jumbo box enclosure
• Verylowfrictionloss• Allmechanicaldesign• LiquidLifefertilizer• Easytorefill“quickconnect”bottle• Alsousethesmartfeederasan
all-natural pest control system• Safeforusearoundkidsandpets
accessories
PumPs
and
ProFeeder
www.americanhydro.com
▲
PUMPS AND ACCESSORIES 2016 Catalog
Burnsville, mn maple Grove, mn Fargo, nd Grimes, ia Berkeley, mo763-592-5701 763-592-5703 701-365-4260 515-661-6800 314-506-4100
18
A1X-R-SNAPRING R-Snap Ring for ProFeeder
not all irrigation products are listed. If you are looking for something you don’t see, please ask!3 stocked at Most stores * MtI Best sellers . . . Best availability
prices subject to change without notice.
PumPs
and
accessories
18
PUMPS AND ACCESSORIES 2016 Catalog
MTI Part Number Description
3 P1X-SVCPLUG Service Plug (Winterizing Plug) P1X Siphon Cap, 2012 or newer P1X Siphon Cap, older than 2012**R Snap Ring P1X Tubing Kit P1X internal mechanism
3 A1X-UP
A1X-GTS A1X-TK-1 A1X-R-SNAPRING A1X-UP-R
Accessories for ProFeeder
** Discontinued when inventory is depleted.
ProFeeder Liquid Life Formula, 1 & 21⁄2 Gallon, Proseries FormulaMTI Part Number Description
3 F1G-1C F2G-2.5C 3 F3G-1C F3G-2.5C 3 F6G-1C 3 F7-1C
1 gallon, Green Up Blend, 23-0-0*2 1⁄2 gallon, Summer/Fall Blend, 16-6-4* 1 gallon, Summer/Fall Blend, No Phos, 14-0-7* 21⁄2 gallon, Summer/Fall Blend, No Phos, 14-0-7*1 gallon, Starter Blend, 5-23-5** 1 gallon, Organic Based Fertilizer additive, 1-1-1*
NatureShield A is a blend of essential oils from garlic, cinnamon, cedar, and castor that synergize to make a safe, effective pest barrier when applied through your sprinkler system. NatureShield A effectively controls mosquitos, roaches, ants, aphids, white flies, gnats, snails, slugs, and other landscape pests.
3 NS-1C NatureShield All Purpose, all natural pest control
** By special order only.
NOTE: Other sizes can be special ordered, may require to purchase by box quantity only.
MTI Part Number Description
Feeder Systems
2670 Complete Rid O' Rust Kit with 30-gallon tank and 5 GPD 110 volt Pump Start Relay
MTI Part Number Description
Metering Pump
2678 Stenner 85MPHP5 fixed rate pump, 110 Volt, 5 GPD(includes 20' of suction/discharge tubing)
2688 Stenner 45MHP10 adjustable feed rate pump, 110 Volt, 10 GPD
* Limited Availability, while supplies last
MTI Part Number Description
NatureShield All Purpose, all natural pest control
NS-8 8oz bottle, use 8oz for 2-gallon sprayer
Burnsville, mN maple Grove, mN Fargo, ND Grimes, IA Berkeley, mo763-592-5701 763-592-5703 701-365-4260 515-661-6800 314-506-4100
PumPs
and
accessories
18
MTI Part Number Description
3 265057-I 30-gallon tank and top for injection system
3 2666 Formula 2000, 1 gallon, hard water blend* 3 2667 Formula 3000, 1 gallon, for rust stains and scaling
3 Test-8 Test kit, iron and hardness AK4010B 100’ 1/4” suction/discharge tubing UCCP201 #1 tube assembly w/ends (S-PSKH01)S-PSKH01 #1 Pump service kit includes 1 tube, ferrules, nuts (For 2678 Stenner pump)
You Can Get Rid of Rust Forever.sTain PreVenTer
www.americanhydro.com
▲
Rid O’ Rust 2000 Rid O’ Rust 3000
PUMPS AND ACCESSORIES 2016 Catalog
Feed Tanks
Rid O' Rust Stain Prevention FormulaMTI Part Number Description RR1 Formula 2000, 64oz, 2x Concentration
Rid O' Rust Stain RemoverMTI Part Number Description
3 2662 Rust Stain Remover, gallon, liquid, 11⁄2 cups to 1 galllon of water
2653 Rid O’ Rust powdered stain remover, 12 oz. bottle12 oz. to each 1 gallon of water
AccessoriesMTI Part Number Description
2810 Pump Start Relay, 110V, 20 Amp
sTain remoVer
Caution: The ingredient in Rust Stain Remover crystallizes at 40 degrees or less. Should be stored in warm area.Note: This product cannot prevent stains caused by ferric iron and tannins.
▲
www.proproducts.com/ourbrands/AmericanHydro/Calculator.aspx
• Premixedtocoverapproximately400squarefeetpergallon.• Removesmoststainswithoutscrubbing;simplysprayonandwashaway.• Safeforapplicationonmostpaintedorunpaintedsurfaces,metalsurfaces,stucco,concret
stonegroutandasphalt;willnotetchconcrete.• Donotapplytomanufacturedpaintstainsorbrickthatcontainsoxidepigment.• Biodegradableandnon-carcinogenic.
• Withnormalapplication,willnotharmgrassorshrubs.
e,
Rid O’ Rust Stain Remover
Rid O' Rust Stain Remover
not all irrigation products are listed. if you are looking for something you don’t see, please ask!3 stocked at most stores * mTi Best sellers . . . Best availability
Prices subject to change without notice.
PumPs
and
accessories
PUMPS AND ACCESSORIES 2016 Catalog
18
*Based on usage of30-gallon tank
PUMPS BY MAXIMUM FEED RATE
dosaGe cHarT For inJecTion sYsTems
MULTIPLIER NUMBERS
5 GPD(.21 GPH)
10 GPD (.42 GPH)or 11 GPD (.46 GPH)
Irrigation system maximum flow rate
in Gallons Per Minute (GPM)
10 GPM15 GPM20 GPM25 GPM30 GPM40 GPM50 GPM60 GPM70 GPM80 GPM90 GPM
100 GPM
FIXED
0.851.291.712.152.57
0.851.291.712.152.57
0.560.841.131.411.69
0.430.640.861.071.29
PERCENT SETTING
NOT RECOMMENDED
50% 75% 100%
Example: Assume a maximum flow rate of 25 GPM, a 10 GPD pump set at 50%, and an iron content of 2.
*Please note: The amount of Rid O’Rust is dosed in gallons forFormulas300,1000,2000and3000;andquartsforFormula500.
10 GPM CALCULATION CHART
PERCENT SETTING
50%
2.1525 GPM➡
2.15 x 2 = 4.30MULTIPLIER X IRON
Amount ofRid O’Rust to add
to the tank*=
Hours of operation before refill
MULTIPLIER NUMBERS5 GPD
(.21 GPH) 10 GPD (.42 GPH)
TANK SIZE
30 GALLON
65 GALLON*2.25 X THE AMOUNT
OF RID O’RUST
100 GALLON*3.33 X THE AMOUNT
OF RID O’RUST
FIXED
143 HOURS 143 HOURS 94 HOURS 71 HOURS
309 HOURS 309 HOURS 203 HOURS 155 HOURS
476 HOURS 476 HOURS 313 HOURS 238 HOURS
PERCENT SETTING50%100% 75% 100%
#2678 - 5 GPD Fixed Rate #2688 = 10 GPD Adjustable Rate
www.americanhydro.com
▲
➡
injection system installation
Irrigation rust stain prevention, for irrigation only.
1. If there is no pressure tank, the metering pump may be connected to the pump start relay for the well pump so that the well pump and the metering pump turn on simultaneously. 2. If there is a pressure tank, the metering pump must be connected to the controller unit for the irrigation system. This can be done using the pump start circuit in the controller unity or by installing a separtate pump start relay and connecting that relay to the controller unit. 3. Plumbing code typically requires a backflow device. The metering pump injection point should be pointed downstream of the backflow device and upstream on the first zone (after the backflow device and before the first zone).
not all irrigation products are listed. if you are looking for something you don’t see, please ask!3 stocked at most stores * mTi Best sellers . . . Best availability
Prices subject to change without notice.
PumPs
and
accessories
PUMPS AND ACCESSORIES 2016 Catalog
18
• Anitrogen-richsolutionthatenhancesgrassgreening.
• Designedtobefedthroughtheirrigationsystemandprovide a steady stream of a small quantity of nutrient.
• Willnotburnyourgrasslikegranularfertilizer.
• Willnotrunoffandpollutebodiesofwater.
GrassSoGreen Fertilizer can be mixed in the same feeder system with Rid O’Rust Rust Stain Prevention Formulas.
MTI Part Number Description
3 2655 GrassSoGreen Fertilizer, Gallon, 19-0-0
CHEMICALSFertilizer for the Irrigation System
Size of Lawn in Gallons of GrassSoGreenSquare Feet to be Applied per Month
1000 0.25 2000 0.5 3000 0.75 4000 1.0 5000 1.25
DETERMINING DOSAGE:Determine how many months or portions of a month it
takes for your feeder system to empty and dose accord-ingly. Example: if it takes two months for your feeder to
empty and you have 2000 sq. ft. of lawn, put two gallons of GrassSoGreen into the tank.
GrassSoGreen Fertilizer
www.americanhydro.com
▲
F4G-1 All Purpose (Organic Based), Gallon, 7-7-7
Water meters by mccrometer from Great PlainsMTI Part Number Description
MW506 6" Water Meter Flg
See Sales Representative for other available styles.
WYe strainers and screensMTI Part Number Description
GV381-30 3" Y Strainer GV381-40 4" Y Strainer GV381-60 6" Y Strainer GV381-30MS 3" Kitz Mesh Screen Only GV381-40MS 4" Kitz Mesh Screen Only
silent check ValveMTI Part Number Description
GN20SCK 2" Wafer Silent Check Valve GN30SCK 3" Wafer Silent Check Valve GN40SCK 4" Wafer Silent Check Valve GN60SCK 6" Wafer Silent Check Valve GN80SCK 8" Wafer Silent Check Valve
mcdonnell Flow switchMTI Part Number Description
GNFS4-3 1" McDonnell Flow Switch GNFS4-15 1"–6" Paddle Kit
cLa-VaLMTI Part Number Description
CV-68373A Screen filter X42N-2
CRD - Downstream Pressure ReducerCV-C5256H Disc Retainer Assembly 20-300, Brass
(Should replace every year)CV-C8348K Disc Retainer Assembly, 30-300, Stainless Steel CV-9170002b Repair Kit, includes diaphragm
CRL - Pressure SustainingCV-C9158B Disc Retainer, Stainless Steel CV-9170007A Repair Kit
55F - Pump OverflowCV-9170007A Repair Kit, same as on CRL
Water Meter
Strainer
PumPs
and
accessories
PUMPS AND ACCESSORIES 2016 Catalog
Burnsville, mn maple Grove, mn Fargo, nd Grimes, ia Berkeley, mo763-592-5701 763-592-5703 701-365-4260 515-661-6800 314-506-4100
18
not all irrigation products are listed. if you are looking for something you don’t see, please ask!3 stocked at most stores * mTi Best sellers . . . Best availability
Prices subject to change without notice.
accessories
PumPs
and
cLa-VaL (cont’d.)MTI Part Number Description
Limit SwitchCV-00951E O-Ring for stem, need two CV-8004701C Adjustable Collar with set screw** CV-34637K Microswitch only
**Discontinuedwheninventoryisdepleted;useCV-20441701E.
Flanges, PVcMTI Part Number Description
PL854-020 2" Flange Slip Sch 80, Two Piece 3* PL854-030 3" Flange Slip Sch 80, Two Piece 3* PL854-040 4" Flange Slip Sch 80, Two Piece 3* PL854-060 6" Flange Slip Sch 80, Two Piece PL854-080 8" Flange Slip Sch 80, Two Piece
Note: Gaskets, next page.
Flanges, metalMTI Part Number Description
3 GN2X6CF 2" x 6" STD CI Comp Flange 3 GN25X7CF 21⁄2" x 7" BK THD Comp Flg 3* GN3X75CF 3" x 71⁄2" BK THD Comp Flg GN3X9CF 3" x 9" BK THD Comp Flg, Reducing 3* GN4X9CF 4" x 9" BK THD Comp Flg 3* GN6X11CF 6" x 11" BK THD Comp Flg 3 GN8X135CF 8" x 131⁄2" BK THD Comp Flg
3* GN3X75SOWF 3" x 71⁄2" Slip on Weld Flange 3* GN4X9SOWF 4" x 9" Slip on Weld Flange 3* GN6X11SOWF 6" x 11" Slip on Weld Flange 3* GN8X135SOWF 8" x 131⁄2" Slip on Weld Flange
For plastic flanges, see Section 9.
Flange accessories
Pipe Size Diameter of Bolt Number of Bolts Bolt Length§
2" 5/8" 4 3” 3" 5/8" 4 3” 4" 5/8" 8 3” 6" 3/4" 8 3 1/4”
§ 0ther bolt lengths available.
MTI Part Number Description
MI5/8X3 5/8" x 3" Bolt
MI3/4X3 3/4" x 31⁄4" Bolt
MI5/8HX 5/8" Heavy Hex Nut MI3/4HX 3/4" Heavy Hex Nut
PVC Flange
Metal Flange
PUMPS AND ACCESSORIES 2016 Catalog
18
Flange accessories (cont’d.)
PART NUMBERSSize Bolt Hex Nut Ring Gasket Full Face Gasket2" MI5/8X3 MI5/8HX GN20RG or GN20FFG3" MI5/8X3 MI5/8HX GN30RG or GN30FFG4" MI5/8X3 MI5/8HX GN40RG or GN40FFG6" MI3/4X3 MI3/4HX GN60RG or GN60FFG
MTI Part Number Description
GN20RG 2" Ring Gasket GN30RG 3" Ring Gasket GN40RG 4" Ring Gasket GN60RG 6" Ring Gasket GN80RG 8" Ring Gasket GN1ORG 10" Ring Gasket
GN20FFG 2" Full Faced Gasket GN25FFG 21⁄2" Full Faced Gasket GN30FFG 3" Full Faced Gasket 3* GN40FFG 4" Full Faced Gasket GN60FFG 6" Full Faced Gasket GN80FFG 8" Full Faced Gasket GN1OFFG 10" Full Faced Gasket
Note: The sizes above are the inside diameter of the gasket.
Wessels Tanks - diaphragm Pressure TankMTI Part Number Description
PR16T 16-Gallon Tank PR80T 80-Gallon Tank PR132T 132-Gallon Tank
PR16B 16-Gallon Bladder Only PR80B 80-Gallon Bladder Only PR132B 132-Gallon Bladder Only
Hand PumpsMTI Part Number Description
999-99 Larsen Suction Gun
3 XW136PF Chugger Extra-Large Suction Gun 3' Outlet Hose
3 XW136PF-6 Chugger Extra-Large Suction Gun 6' Outlet Hose
3 XWFV1-3/4 Chugger Foot Valve Assembly
We have additional sales information on many items not listed in this catalog including:
• Lakos Sand Separators• Cla-Val Automatic Valves• Pump Station Products
Ring Gasket
Full Faced Gasket
Manufactured by Wessels, these tanks are pre-charged and hydro-pneumatic for well
and water systems.Replacement diaphragms available.
Suction Gun
An excellent pump for removing water from water meter boxes. A general purpose pump that is lightweight PVC construction, easy to operate, won’t rust or corrode, non-sparking,
self-priming, and 35 oz./stroke.
accessories
PumPs
and
PUMPS AND ACCESSORIES 2016 Catalog
Burnsville, mn maple Grove, mn Fargo, nd Grimes, ia Berkeley, mo763-592-5701 763-592-5703 701-365-4260 515-661-6800 314-506-4100
18