Upload
anand-thatvamashee
View
215
Download
0
Embed Size (px)
Citation preview
8/2/2019 Purchase of Tools and Equipment
1/16
CSTI ABUL KHURANA LIST OF TOOLS & EQUIPMENT For the trade of WELDER(GAS AND ELECTRIC) (For a batch of Two Unit of 24 trainees Each)
Sl.
No.
Items Qty Rateper
Item
(in Rs)
Figures
Rate per Item (in Rs) Words
1 Gloves pair leather 13
2 Apron leather 13
3 Screen welding helmet type 13
4 Screen welding hand 13
5 Goggles pair welder 13
6 Hammer Scaling 0.25 kg. with handle 13
7 Chisel cold flat 19 mm 13
8 Centre punch 9 mm X127 mm 13
9 Dividers 20 cm 13
10 Caliper outside 15 cm 13
11
Rule 60 cm two fold brass tipped to read
inches and mm 13
12 Wire brush 15 cm x 3.7 cm 13
13 Spark Lighter 13
14 Chipping screen hand 13
15 Safety boots for welders 26
16 Safety goggles 13
17 Square blade 15 cm 13
18 Scriber 15 cm 13
19 Tongs holing 30 cm 13
SHOP OUTFIT
Sr.
No Item
20 Weld measuring gauge fillet and butt. 2
21
Heavy duty cutting and sqouging blow
pipe with 1 set
cutting and sqouging nozzles
22
Welding rubber hose, oxygen and
acetylene 8 mm
65
metres
each
23 Pressure regulator oxygen double stage 8 nos.
24 Pressure regulator acetylene Regulators 8 nos.
25 Rubber hose pipe black and red 5 mm 30 mt.
GENERAL INSTALLATION
26
Welding cables to carry 350 amps with
flexible rubber
45
meter
27 Lugs for cables (Copper)
24
nos.
28
Bench shear hand capacity upto 5 mm
(High Carbon) 1
29 Power hacksaw 1
8/2/2019 Purchase of Tools and Equipment
2/16
30
Electrode driving over-thermostatically
controlled 1no.
temperature 0-250 C 10 KG/Cap.
31
Braze weld equipment Erazer which can
be used 1 no.
with existing welding transformer
32 Metal rack 182 cm x 152 cm x 45 cm 1
33 Steel lockers with 8 Pigeon holes 2 nos.
8/2/2019 Purchase of Tools and Equipment
3/16
LIST OF TOOLS AND EQUIPMENTS FOR THE TRADE OF PLUMBER
TWO UNITS OF 32 TRAINEES
Sl.
No.
Items Qty Rateper
Item(in Rs)
Figures
Rate per Item (in Rs) Words
1 Rule steel 300 mm both in inch
and mm.
17
2 Rule wooden 4 fold 600 mm. 17
3 Hacksaw frame adjustable for 250
to 300 mm.
17
4 Scriber 200 mm. 17
5 Centre punch 100 mm. 17
6 Chisel cold flat 20 x 250 mm. 17
7 Hammer ball pein 800 gms. 17
8 Hammer ball pein 300 gms. 17
9 Flie flat rough 300 mm. 17
10 Level spirit wooden 300 mm. 1711 Plumb bob 50 gms. 17
12 Traowel 125 IS : 6013. 17
13 Stillson wrench 200 & 350 mm. 17
14 Screw driver 250 mm. 17
15 Wooden mallet small IS : 2022. 17
16 Cutting pliers 200 IS : 365 17
17 Steel tape. 17
TOOLS, MEASURING INSTRUMENTS, SHOP OUTFIT & GENERAL INSTALLATIONS
18 Surface plate 400 x 400 mm grade
1.
1
19 Scribing block universal 300 mm. 2
20 Hand vice jaw 50 mm. 2
21 File half round rough 300 mm. 2
22 File square rough 250 mm. 2
23 File square smooth 200 mm. 2
24 File triangular rough 250 mm 2
25 File flat rasp 250 mm. 2
26 File triangular smooth 200 mm. 2
27 Chisel cross cut 6 x 150 mm IS :
402
2
28 Chisel round nose 3 x 150 mm IS :402
2
29 Tap and die set to cut BSP thread. 1
30 Punch number set. 1
31 Chase wedge 50 mm. 2
32 Dresser lead 350 x 50 mm. 2
33 Stick setting in 350 x 50 mm. 2
34 Saw plumber 300 mm. 2
35 Spanner monkry upto 50 mm. 2
8/2/2019 Purchase of Tools and Equipment
4/16
36 Cutter, pipe wheel type 6 mm to25 mm.
1
37 Pipe jointer, lead, universal. 1
38 Oil stone 150 mm x 50 mm x 25
mm.
2
39 Soldering iron, copper fit, fireheated, hatched, straight 500 gms.
4
40 Snip straight 250 mm 2
41 Inside caliper 150 mm. 242 Caliper outside 150 mm. 2
43 Odd leg caliper 200 mm. 2
44 Tenon saw. 2
45 Handsaw. 2
46 Mortice chisel. 2
47 Firmer chisel. 2
48 Jack plane 2
49 Pipe opener. 1
50 Washer cutter. 1
51 Pressing stick. 1
52 Mandrel. 253 Plumber kit containing tam pin,
Bent pin, plumbers hammers
dressers, mallets, chase wedges,
draw knife and step turner.
2
54 Bobbin and follower. 2
55 Bend bolt. 2
56 Sheet lead knife. 2
57 Chipping knife. 2
58 Mirror 100 x 150 mm. 2
59 Splash stick 2
60 Soil pot with brush 161 Pot hook. 1
62 Turn pin. 1
63 D.E. spanners 7 x 8, 10 x 11, 13, x17, 19 x 22, 24 x 27, IS: 2028
(Drop Forged)
2
64 Branch gimlets. 2
65 Bending spring. 1
66 Long dummy. 2
67 Short dummy. 2
68 Plumbers ladle. 2
69 Joining cramp. 2
70 Plumbers metal melting pot 10 kg. 1
71 Tool caulking set of 2. 2
72 Stillson pattern pipe wrenches 450
mm to take pipe up to 52 mm diaIS : 4003
2
73 Anvil 50 or 63 km. IS : 510. 1
74 Vice leg 75 mm, jaw on stand IS :
2588.
1
8/2/2019 Purchase of Tools and Equipment
5/16
75 Drill twist (Strainght shank) 3 mmto 6 mm.
1
76 Portable forge 450 mm with handblower.
1
77 Flat smithy tong. 2
78 Bath tub small size. 1
79 Step tap water 20 mm IS : 781. 4
80 Water heater 2 litres. 1
81 Water closet Indian type completewith over hand cistern. 1
82 Urinal wall type complete withautomatic system.
1
83 Watermeter 2
84 Steel lockers with 8 drawers. 285 Metal rack 1800 x 1500 x 4500
mm1
86 Katehel brack with post and clampflat drill 6 to 35 mm by 0.2 mm.
1
87 PVC welding plant. 1
88 Electric pump 1 HP. 189 D.E. pedestal grinder with two
wheels 175 rough and smooth.
1
90 Hydraulic pressure machines for
testing leakage in GI pipe fittingsetc.
1
91 Sight rail and banning rod. 1
92 Ratchet pipe die 15 mm to 32 mm. 1
93 Bench Drilling machine with
chuck and key up to 15 mm cap
1
94 Double face hammers. 2
95 Dormat,Pickle, Spade, Girmale. 196 Pipe bender (Hydraulic type) 1
97 Mankey Plier (Gas pliers) 4
8/2/2019 Purchase of Tools and Equipment
6/16
List of Tools & Equipment for the Trade of Electrician( For a batch one unit of 16 trainees)
Sl.
No.
Items Qty Rateper
Item(in Rs)
Figures
Rate per Item (in Rs) Words
Tool Kit
1 Rule wooden 4 fold 60 mm 17
2 Pller Insulated 150 mm 11
3 Plier side cutting 150mm 14
4 Screw driver 100 mm 11
5 Screw driver 150 mm 11
6Electriclan conncelor, sciew driver
100mm
17
7 Heavy duty screw driver 200mm 14
8Electrician screw driver 250mm
thin stem insulated handle
14
9 Punch center 150mm x 9mm 16
10 Knife double bladed electcian 16
11 Ruler steel 300mm 17
12 Saw tenon 250mm 17
13Hammer, closs pein 115 grams
with handle
15
14Hammer ball pein 0,75 kg with
handle
17
15 Flrmer chisel wood 12mm 15
16 Gimlet 6mm 17
17 Bradawl 17
18Scriber 150 mm x 4mm (knurledcenter position)
17
19 Pincer 150 mm 17
Shop Tools, Instruments &
Machiner
Sr.No
Item
20C. Clnmps 200 mm, 150 mm, 100mm
02
21 Melting Pot 01
22 Ladle 2
23Chisel wood firmer 25 mm and 6
mm
4
24Pillnr elcetrle drill Machino 12 mm
eapacity
1
25 Oll can 0.12 lltre 2
26 Grease gun (1kg) 1
27 Out side micrometer 0 to 25 mm 1
28 Bench grinder motorised 1
29 Rawl Plug tool and bit 2
8/2/2019 Purchase of Tools and Equipment
7/16
30 Bearing puller 1
31 Hygro Meter 2
32Thermometer 0 to 100 Deg.
Centigrade
1
33 Scissors blade 150 mm 4
34 Chisel cold flat 12 mm 2
35 Mallct hard wood 0.50 kg. 4
36 Hammer exetor type 0.40 Kgs 8
37 Hexsaw Frame 200 mm 300mmadjustable 2
38 Square try 150 mm blade 3
39Dlvlder 150 mm outside & inside
callper
2
40 Plier flat nose 100 mm 4
41 Plier gas round nose 100 mm 4
42 Pller Gas 150 mm 4
43 Tweezer 100 mm 4
44 Snip strnight 150 mm 2
45 Snip 150 mm 2
46 Sppnner D.E.W/W standard set 247 Deill hand inace 0 to 100 mm 4
48Drill S.S Twist block 3mm. 5.mm0.mm set of 3
4
49 Plane smoothing cullers, 50 mm 4
50 Gauge, wire imperial 1
51 File flat 200mm 2nd cut 7
52 File half round 200 mm 2nd cut 3
53 File round 200 mm 2nd cut 3
54 File flat 150 rough 4
55 File Flat 250 mm Bastard 4
56 File flat 250 mm smooth 457 Rasp, half round 200 bastard 4
58 Copper bit soldering iron 0.25 Kgs 4
59 Desoldering gun 4
60 Vice hand 50 mm Jaw 3
61 Vice table jaw 100 mm 7
62 Vice hand 50 mm jaw 3
63Pipe cutter to cut pipes up to 5 cmdia
4
64Pipe cutter to cut pipes above 5 cmdia
1
65Stock and dies set for 20 mm to 50
mm GI pipe
1
66 Stock and dies conduit 1
67Multi meter 0 to 1000 m Ohins to2.5 to 500 volt
5
68Mill.Voltmerer center zero 100-0-
100 m volt
1
69 DC Ammeter MC 0-1 A 1
70 Ammeter MC 0-5 A 0
71 Ammeter MC 0-15-25 A 1
8/2/2019 Purchase of Tools and Equipment
8/16
72 AC Ammeter MI 0-5A 1
73 AC Ammeter MI0-15-25A 1
74 KW meter 0-1-3 KWE 2
75A.C Energy meter (single phase 5
amp 230 V)
1
76 Single phase power factor meter 1
77 Frequency meter 1
78 Techno meter with stop watch 1
79 Current transformer 280 Potential transformer 2
81 Growler 1
82 Megger 500 volts 1
83Wheat stone bridge complete with
galvanometer and battery1
84Relays Over current, under
voltage, etc. 3 volt, 100 amp.2
85Contactor 3phase,440volt,16amp.2
NO &2 NC auxiliary contacts1
86 Limit Switch 2
87 Rotary Switch 16A 288
Load bank- 5 KW( Lamp / heater
Type)2
89Brake test arrangement with two
spring balance of 0 to 25 kg rating2
90Knife switch DPDT fitted with fuse
terminals 16 amp12
91Knife switch TPDT fitted with fuse
terminals 16 amp12
92 DC power supply 0 - 100 volt, 5 amp 2
93Inverter 1 KVA Input 12 volt DC,
Output 220 volt AC with 12 battery1
94Voltage stabilizer- Input 150 230
volt AC, Output 220 volt AC1
95Rheostat 0 1 Ohm, 5 Amp.; 0 10
Ohm., 5 Amp. ; 0 25 Ohm,
1 Amp. ; 0 300 Ohm., 1 Amp.
2
96 Domestic appliances
Electric hot plate 1500 watt. 220 Vwith temperature control
2
Electric kettle, 1000 watts, 230 V
2
Electric iron, 1200 watts, 230V
with temperature control
2
Immersion beater 750/1000/1500W-
230 V
2
Geyser 25 liter 240 V (Storage type)
.1
8/2/2019 Purchase of Tools and Equipment
9/16
97 Flux meter 1
98Laboratory type induction coil 6 volt
to 800-10,000 volt1
99. 3-point D.C. starters 1
100 4-point D.C. starters 1
101Cut out, reverse current, over load,
under voltage relays.1
102Starters for 3-phase, 400 V, 50
cycles, 2 to 5 H.P. A.C. motors
Direct on line starter 1
Star delta starter with manual, semi-
auto and automatic1
Auto transformer type starter 1
103
Electrical machine trainer: -Suitable
for demonstrating the construction
and functioning of different types of
DC machines and AC machines
(single phase and three phase).
Should be completed with friction
brake 1 perdynamo meter, instrument panel and
power supply units
1
104
Motor generator (AC to DC)
consisting of :
Motor induction squirrel cage, 7 HP
400 Volts, 50-cycles, 3-phase with
star delta starter and switch directly
coupled to DC shunt generator 5
KW
440 volts, and switch board mounted
with regulator, air circuit breaker,ammeter, voltmeter knife blade
switches and fuses, set complete
with case
iron and plate, fixing bolts,
foundation bolts and flexible
coupling
1
105
Motor generator(DC to AC) set
consisting of -
Motor shunt 5 HP, 440 Volts with
starting compensator and switch
directly
coupled to generator AC. 3.5 KVA,400/230 Volts, 3-Phase, 4 wire, 0.8
PF
50cyccles with exciter and 1 switch
board mounted with regulator,
circuit
breaker, ammeter, voltmeter
frequency meter, knife blade switch
and fuses etc.
Set complete with cast iron bed
plate, fixing bolts, foundation bolts
1
8/2/2019 Purchase of Tools and Equipment
10/16
and
flexible coupling.
106Used DC generators-series, shunt
and compound type for overhauling
practice
1
107D.C. shunt generator, 2.5 KW, 220
V with control pane1
108
D.C. compound generator, 2.5 K.W.
250 V, with control panel includingfiled
rheostat, voltmeter, ammeter and
circuit breaker
1
109
Diesel generator, 5 KVA, withchange over switch, current circuit
breaker, water cooled with
armature, star-delta connections.
1
110Motor series DC, 220 volt, 0.5 to 2
HP, coupled with mechanical load
1
111
Motor shunt DC 220 VOLT, 2 TO
3 HP.
2
112Motor DC compound- wound, 220volt 2 to 3 HP with starter & switch
2
113
Motor of AC Squirrel cage, 3-phase,
400 volt, 50 cycles, 2 to 3 HP with
star delta starter & triple pole ironcled switch fuse.
1
114Motor AC Phase- wound slip ringtype 5 HP 400 volts, 3-phase, 50
cycles with starter and switch fuse
1
115Motor A.C series type 230 V. 50eyeles. 1/4 HP with starter and
switch
1
116Moter AC single phase 230 volt,50 cycles capacitor type with
starter switch 1 HP.
1
117Motor universal 230 volt, 50 cycles
with starter/switch
1
118Stepper Motor with digital
controller
1
119 Fan A.C 230 volt 1200 mm 1
120Transformer three phase, 1 KVA,230/115-50-24-12 volts, 50 cycles,
core type air cooled
3
121
Transformer three phase, 5 KVA
400/230 volts, 50 cycles, delta andstar, shell type oil cooled
2
122Variable auto transformer 0-250 B,5 amps
2
123 Oscilloscope dual trace 30 MHZ 1
124 Function Generator 1
8/2/2019 Purchase of Tools and Equipment
11/16
125 Discrete components trainer 1
126 Linear IC Trainer 1
127 Digital IC Trainer 1
128 Bath Impregnating 1
129 Oven stoving 2
130 Oil testing kit 1
131Battery charger with variable
output 1 KV
1
132 Hydrometer 1133 ACB 5 KVA 1
134
Thyristor/IGBT controlled DC
Moter drive 1 HP with tacho
generator feedback arrangement
1
135
Thyristor/IGBT controlled AC
Moter drive with VVVF control 3phase 2 HP
1
136Lockers with 2 drawers standardsize
2
137Bench working 2.5 x 1.20 x 0.75
meters
4
138 Almirah 2.5 x 1.20 x 0.5 meter 1
139 Instructors table 1
140 Instructors chair 2
141 Fire extinguisher 2
142 Fire buckets 4
143 Metal rack 100x150x45 cm 4
8/2/2019 Purchase of Tools and Equipment
12/16
CSTI ABUL KHURANA
LIST OF TOOLS & EQUIPMENTFor the trade of Carpenter
(For a batch two Units of 32 trainees)
S.
No.
Description Qty Rateper
Item(in Rs)
Figures
Rate per Item (in Rs) Words
1. Rule six 1 meter (inch & mm) 34
2. Marking knife 200 mm length 28
3. Carpenter square 200 mm 29
4. Square bevel 50 mm 34
5. Carpenter marking gauge 22
6. Carpenter mortice gauge 34
7. Saw hand 450 mm 23
8. Saw tenon 300 mm 28
9. Plane jack metal 335 mm x 50
mm
28
10. Plane smoothing Mattel 200 mm x50mm cutter
34
11. Chisel firmer (bevel edge) 6,10,15,20 & 25 mm width (5 Nos)
14
12. Chisel mortice 6,10,15 mm (3Nos)
23
13. Screw driver 300 mm (Cabinetmaker)
34
14. Mallet medium size 23
15. Hammer claw 500 grm 17
16. Oil stone (Carborundum)universal silicon carbitecombination rough & fine 200 x
50 x 25 mm
29
17. Hand brush for bench cleaning
450 mm
34
Tool : Equipment and General
Outfit
18 Contraction scale 1 meter 04
19 Spring caliper inside 150 mm 04
20 Spring caliper out side 04
21 Wing compass 300 mm 0222 Trammel 02
23 Rip saw 600 mm 04
24 Cross cut saw 600 mm 04
25 Key hole saw 250 mm 02
26 Compass saw 350 mm 04
27 Adze 15 kg 04
28 Trying plane meter 450 mm x 60
mm cutter
02
8/2/2019 Purchase of Tools and Equipment
13/16
29 Plane ravvet adjustable 250 x 9mm cutter
04
30 Plough plane with set of 8 cutterup to 12 mm width
04
31 Spoke shaves 50 mm cutter 08
32 Plane adjustable circular 250 mm 04
33 Router plane 04
34 Moulding plane set 04
35 Cabinet scraper 100 mm 0436 Gauge chisel, finner,6,10,12,16,20 mm
08
37 Gauge chisel seriating6,10,12,16,20 mm
08
38 Ball pein hammer 600 grm 03
39 Cross pein hammer 600 grm 04
40 Screw driver 450 mm 04
41 Screw driver 150 mm 02
42 File half round 2nd cut 250 mm 08
43 File slim taper 100 mm 06
44 File slim taper 150 mm 0245 Card file (steel) wire brush for file 04
46 Hand drill 6 mm capacity 08
47 Country drill with bow (balkl
bearing type)
04
48 Ratchet brace 250 mm swap 04
49 Centre bits 6,8,10,12 02
50 Expansion bit sets 02
51 Twist drill bits 6,8,10,12 mm 02
52 Counter sink bit rose type 12 mm 04
53 Breast drill 6 mm capacity 02
54 Center punch 5 0155 Snip straight 200 mm 01
56 Oil can combination side cutting
pliers
02
57 Plunger saw set/pistol grip type 02
58 Number punch 12 mm 02
59 Slip stone 100 mm 08
60 Round crow bar with chisel andclaw end 1070 x 25 mm
02
61 G Clamp 100 mm 08
62 G clamp 150 mm 08
63 G clamp 250 mm 04
64 T Bar cramp 0.6 meter 08
65 T Bar cramp 1.25 meter 04
66 T Bar cramp 1.75 meter 02
67 Carpenter vice 250 mm jaws 14
68 Saw sharpening vice 250 jaws 02
69 Carving tools set 02
70 Goggles pair 02
71 Glass cutter 02
72 Nail punch 04
8/2/2019 Purchase of Tools and Equipment
14/16
73 Surface plate 600 x 600 mm 01
74 Carpenter work bench 2400 x 900
x 800 mm height
08
75 Oil can 04
76 Steel locker 8 compartments, with
individual locks 1980 x 910- x480 mm depth
02
77 Steel almirah shelves 1980 x 910
x 480 mm depth
02
78 Instructor table (half secretariat) 01
79 Instructor chair 02
80 Stool 01
81 Chalk board with easel 01
82 Meterial rack 01
General Installation and
Accessories
83 Combind surfacer and thickener 01
84 Lathe, wood turning 150 mm
height of centres 1.75 meter bedmotorized complete with a set of
turning tools
03
85 Set of turning tools for abovelathe machine
03
86 Tenoning machine (single ended) 01
87 Mortising machine (Combine
hollow chisel and chain)
01
88 Portable electric drill 6 mmcapacity (woif type)
01
89 Portable disc sander 200 mm dia 01
90 Adjustable saw sharpener 0191 Electric heater 1000/1500 W 01
92 Electric blower (Portable) 01
93 Moisture meter 01
94 Grease gun 1kg 01
95 Electrical drying oven (small
type)
01
96 Band saw machine with provision 01
97 Fire extinguisher 02
98 Fire buckets 04
8/2/2019 Purchase of Tools and Equipment
15/16
LIST OF TOOLS AND EQUIPMENT
For a unit of 16 trainees for the Trade of MASON (Building Constructor)
Sl.
No.
Items Qty Rateper
Item(in Rs)
Figures
Rate per Item (in Rs) Words
1. Bolster 4 (100 mm) Chisel 6
2. Pitching tool (Mason) 17
3 Chisels masons hammer
headed punch
6
4. -do- (12mm) 34
5. -do- 1 (25 mm) 34
6. -do- Cross cut type 17
7. -do- (18 mm) 17
8. -do- 1 (35 mm) 17
9. Hammer mason (club) 1 /1lb
6
10. Hammer brick mason (600-
800 gm)
6
11. Level masons 36 (plumb
level ) (1 meter)
16
12. Pins (line) 16
13. Square (steel) 2'0" x 1'0(.75
m x .5 m)
1
14. Trowel plastering double 16
15. Shovels 316. Measuring tape 100 (50 m) 1
17. Ladders 2 to 4 meter 2
18. Sledge hammer 10 lbs 2
19. GI Pipe 1 dia 100
Mtr
20. GI Pipe 12 mm dia 150
Mtr
21. Cello tax board 01
22. Bar bending tool and cutting
tool
1
23. Screw driver 4
24. Four fold foot rule 2' (60 cm) 16
25. Crow bar 1.5 m long 2
26. Scraper 16
27. Snip straight 10" (25 cm) 4
28. Carpenter tool kit consisting
of 16 set
(a) Hand saw 01
(b) Mortise chisel 01
8/2/2019 Purchase of Tools and Equipment
16/16
(c) Tenion saw 01
(d) Firmer chisel 01
(e) Mallet 01
(f) Carpenter claw hammer 01
(g) Hand brace with bits 01
(h) Plane 01
29. Tubular scaffolding 25mm dia
with coupling and fitting
complete
1
30. Steel measuring boxes 1
31 Adjustable props. Steel 24
32 Flat for 4' x 4' x 6' (1 m x 1.5
m x 2 m)
2
33 Bending rod 2
34 Dumpy level with stand &
staff
2
35 Spanner set (Drop Forged) 1
36 Steel shuttering 400 sq/200 sq.
m
1
37 Bench grinder 1
38 Drill machine 1