Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
ONE
REV.: 20160531
ADDENDUM - SUGGESTED WIRING CONFIGURATION ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ
NOTESNOTE Hood Status : functional if equipped with a factory hood switch.
HOOD STATUS : fonctionnel si équipé d’un commutateur de capot d’origine.
Vehicle DATA functions supported (Functional if equipped)Fonctions du véhicules supportés en DATA (Fonctionnelle si est équipé)
Vehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule sup-portées dans ce diagramme (fonctionnelles si équipé)
VEHICLEVEHICULES
YEARS ANNÉES Im
mob
ilize
rby
pass
Lock
Unl
ock
Arm
Dis
arm
Hor
n
Park
ing
Ligh
ts
RA
P co
ntro
l
Tach
omet
er
Doo
r Sta
tus
Trun
k S
tatu
s
Hoo
d S
tatu
s
Han
d-B
rake
S
tatu
s
Foot
-Bra
ke
Sta
tus
Push
-to-S
tart
Con
trol
OEM
Rem
ote
Mon
itorin
g
R.S
. OEM
re
mot
e S
tand
Alo
ne
com
patib
le
INFINITIQ50 Push-to-start 2014-2016 • • • • • • • • • • • • • • • • •
Guide # 33241
ADDENDUM - SUGGESTED WIRING CONFIGURATION
SCHÉMA DE BRANCHEMENT SUGGÉRÉ
2014
INFINITIQ50 Push-to-start
Q50
(-)Security LED (-)Start/Stop
(-)UnlockDisarm
BCM Green 40-Pin connectorBCM Connecteur Vert de 40-pins
BCM located in passengerkick panel | BCM Situé dansle panneau latéral côté passager
BCM Black 40-Pin connectorBCM Connecteur Noir de 40-pins
(~)CAN HIGH (~)CAN LOW
(-)Trunk Release
(-)LockArm
(-)Ignition2
(+)Ignition1
(+)Accessory1
(-)Starter
BCM Grey 24-Pin connectorBCM Connecteur Gris de 24-pins
(-)Driver door Pin
BCM Black 24-Pin connectorBCM Connecteur Noir de 24-pins
(+)Accessory2
(+)12V(-)Starter1
IPDM-E/R Engine compartment.IPDM-E/R Situé Sous le capot
located
(+)Neutral
(+)Starter2 Output
PUSHSTART
REGULAR INSTALLATIONINSTALLATION RÉGULIÈRE
Program bypass option:Programmez l’option du contournement:
UNIT OPTIONOPTION UNITE DESCRIPTION
C1OEM Remote status (Lock/Unlock) monitoringSuivi des status (Verrouillage/Déverrouil-lage) de la télécommande d’origine
Program remote starter option:
Programmez l’option démarreur à distance:
FUNCTIONFONCTION MODE DESCRIPTION
31 4(+) Parking Light (E1)(+) Accessory (E2)
(+) Feux de stationnement (E1)(+) Accessoire (E2)
Program remote starter option for R.S. OEM REMOTE STAND
ALONE:Programmez l’option démarreur à distance
pour TÉLÉCOMMANDE D’ORIGINE STAND
ALONE:
FUNCTIONFONCTION MODE DESCRIPTION
38 2Enable Press 3x Lock to remote start with the OEM remote.
ActivéAppuyez x3 sur Verrouille de la télécommance d’origine pour démarrer à distance le véhicule.
Program remote starter option:
Programmez l’option démarreur à distance:
FUNCTIONFONCTION MODE DESCRIPTION
6 6Desarm before shut down
Désarme avant la fermeture du moteur
Parts required (Not included) Pièce(s) requise(s) (Non incluse(s))AUTOMATIC TRANSMISSION1X 30 Amp Relay3X 1 Amp Diode1X 15 Amp Fuse1X FuseMANUAL TRANSMISSION1X 15 Amp Fuse 2X 1 Amp Diode
TRANSMISSION AUTOMATIQUE1X Relais 30 Amp3X Diode 1 Amp1X fusible 15 Amp1X FusibleTRANSMISSION MANUELLE1X fusible 15 Amp2X Diode 1 Amp
HARDWARE VERSIONVERSION MATÉRIELLE
REMOTE STARTER FIRMWARE VERSION
VERSION LOGICIELLE DU DÉMARREUR À DISTANCE
BYPASS FIRMWARE VERSION
This manual may change without notice. www.fortinbypass.com for latest version.
Ce Guide peut faire l’objet de changement sans préavis. www.fortinbypass.com pour la
récente version. 3 1.[19] 72.[22]
MINIMUM NISSAN/INFINITI MINIMUM
Page 1 / 7
REGULAR INSTALLATIONINSTALLATION RÉGULIÈRE
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DESCRIPTION | DESCRIPTION
(-)Security LED (-)Start/Stop
(-)UnlockDisarm
BCM Green 40-Pin connectorBCM Connecteur Vert de 40-pins
BCM Black 40-Pin connectorBCM Connecteur Noir de 40-pins
BCM Grey 24-Pin connectorBCM Connecteur Gris de 24-pins
BCM Black 24-Pin connectorBCM Connecteur Noir de 24-pins
(+)Accessory2
BCM White 15-Pin connectorBCM Connecteur Blanc de 15-pins
(+)12 Volts
(+)12V
(+)Starter1
IPDM-E/R located Engine compartmentIPDM-E/R Situé Sous le capot
(-)Driver door Pin
(+)Parking Lights
Back of glove boxDerrière la boîte à gants
BCM located in passengerkick panel | BCM Situé dansle panneau latéral côté passager
(+)Neutral
(-)Starter2
(~)CAN HIGH (~)CAN LOW
(-)Trunk Release
(-)LockArm
(-)Ignition2
(+)Ignition1
(+)Accessory1
(-)Starter1
Page 2 / 7
Yellow In A1 Purple Out A2
Purple/White Out A3 Green Out A4 White Out A5
Orange Out A6 Orange/Black Out A7
Dk.Blue Out A8 Red/Blue In A9
Lt.Blue/Black In/ Out A10 Black In A11 Pink Out A12
Yellow/Black Out A13 Brown/White In A14
Pink/Black In A15 Purple/Yellow In /Out A16 Green/White In /Out A17
Green/Red In /Out A18 White/Black Out A19
Lt.Blue In /Out A20
C5 Brown C4 Gray/Black C3 Gray C2 Orange/Brown C1 Orange/Green
D6 White/Red D5 White/Blue D4 White/Green D3 Yellow/Red D2 Yellow/Blue D1 Yellow/Green
White Out E1 Orange Out E2
Red In E3 Black In E4 Pink In/ Out E5
Yellow Out E6
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
WIRING CONNECTION | GUIDE DE BRANCHEMENTS
Yellow In A1Purple Out A2
Purple/White Out A3Green Out A4White Out A5
Orange Out A6Orange/Black Out A7
Dk.Blue Out A8Red/Blue In A9
Lt.Blue/Black In/Out A10Black In A11Pink Out A12
Yellow/Black Out A13Brown/White In A14
Pink/Black In A15Purple/Yellow In/Out A16Green/White In/Out A17
Green/Red In/Out A18White/Black Out A19
Lt.Blue In/Out A20
C5 Brown C4 Gray/Black C3 Gray C2 Orange/Brown C1 Orange/Green
D6 White/Red D5 White/Blue D4 White/Green D3 Yellow/Red D2 Yellow/Blue D1 Yellow/Green
White Out E1Orange Out E2
Red In E3Black In E4Pink In/Out E5
Yellow Out E6
HOOD PIN CONTACT CAPOT
(-) Hood pin
CUT LOOP FOR AUTOMATIC TRANSMISSION MODE.COUPEZ LA BOUCLE POUR LE MODE TRANSMISSION AUTOMATIQUE.
Yellow/GreenYellow/BlueYellow/Red
White/Blue
Orange/GreenOrange/Brown
Brown
Yellow
Green/RedGreen/White
Purple/Yellow
Brown/White
PinkBlack
Red/BlueDk.Blue
Green
Yellow
1718192021222324
123456789101112
131415161718192021222324
123456789101112161718 131415
2122232526272829303132
23456789101112
3335
16171920 131415
36373839
12345678101112
BCM Grey 24-Pinconnector
BCM ConnecteurGris de 24-pins
BCMGreen 40-Pin
connectorBCM
Connecteur Vertde 40-pins
BCM Black 40-Pin connectorBCM Connecteur Noir de 40-pins
BCM Black 24-Pin connectorBCM Connecteur Noir de 24-pins
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
Autolight Shutdown.Fermeture
des lumièresautomatiques.
34
2123242528293132333536373839
40
1314151634 30 27 26 22
118
1314
1516
1718
1920
2122
2324
1315
1617
1819
2021
2223
24
12
34
56
78
910
1112
12
34
56
78
910
1112
14
1 2 3 4 5 6 7 8 9 10 11 12 16 17 1813 14 15
21 22 23 24 25 26 28 29 30 31 32 33 34 35 36 37 38 39
19
27
2122
2325
2627
2829
3031
32
23
45
67
89
1011
12
3334
35
1617
1920
1314
15
3637
3839
4024
118
40
20
1
10
23
46
87
914
1513
1211
5
D4
CU
T
1920
9
40 34
24
(-)Lock (-)Unlock (-)Driver door Pin
(+)Acces-sory2
(~)CANLOW
(~)CAN HIGH(-)Ignition2 (+)Ignition1 (+)Acces-
sory1(-)Start/Stop
(+)12V
(+)Parking Lights
(-)Trunkrelease
( ) Security LED
BCM White 15-Pin connectorBCM Connecteur Blanc de 15-pin
1
10
2346
8 791415 13 12 11
5 34 1256789101216
1718
131415
23242528293132 192030 27 26 22 21
White32-Pin connector
Back of glove boxConnecteur Blanc
de 32-pinsDerrière la boîte
à gants
PurpleMauve
RedRouge
BlueBleu
BlueBleu
PinkRose
BlackNoir
BlackNoir
White/BlackBlanc/Noir
WhiteBlanc
BlueBleu
Lt.BlueBleu Pâle
RedRouge
Empty pinPin vide
Empty pinPin vide
11
BCM located in passenger kick panel.BCM Situé dans le panneau latéral côté passager.
(-)Starter1
2222For idle mode only
Pour modevéhicule en attente seulement
RedRouge
Q50
22For idle mode only
Pour modevéhicule en attente seulement
CAN HIGHCAN LOW
Security LED
(-) Lock/Arm(-) Unlock
(+) Accessory(+) ParkingLight
(-) Start/Stop
(+) 12VGround
(-) Trunk Release
(-) Ignition2
Security LED
1A Diode
1A Diode
E2
(+) Ignition1
(-) Disarm(-) Horn
A13 A10E5 E2 E2C4 C3E3 A3/A6A19 D6 A20A2
(-) Driver Door Pin
A7(-)HORNGreenVert Steering Column. Yellow 6-Pin
connector at steering column. Pin 3. (test before connecting)
Colonne de direction. A la colonne de direcion, Connecteur
Jaune 6-pins. Pin 3. (tester avant de connecter)
GROUND
E1
CAUTION ! THIS INSTALLATION MUST BE DONE BY A QUALIFIED TECHNICIAN : A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE'S BCM.
ATTENTION ! CETTE INSTALLATION DOIT ÊTRE FAITE PAR UN TECHNICIEN QUALIFIÉ : UN MAUVAIS BRANCHE-MENT PEUT CAUSER DES DOMMAGES PERMANENTS AU BCM DU VÉHICULE.
(-) Starter
A5
15 AmpFuse
Page 3 / 7
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
FUSE
CAUTION: Permanent damage can be done to the vehicle if this relay is not installed.ATTENTION: Des dommages permanents peuvent être causés au véhicule si ce relai n'est pas installé.
Protect the Relay from moisture otherwise damage may occur.Protégez le Relai des intempéries. L'eau peut causer des dommages.
AUTOMATIC TRANSMISSIONTRANSMISSION AUTOMATIQUE
IPDM-E/R
Q50 Lt.Blue
1 2 3 4 5 6 7 8 9 10 11 12 16
17 18
13 14
21 22 23 24 25 26 28 29 30 31 3220 27
IPDM-E/RIPDM-E/R
White 32-Pin connectorConnecteur Blanc
de 32-pins
30
8685 87
87a
IPDM-E/R
IPDM-E/R
Black1-Pin connector
ConnecteurNoir de 1-pins
IPDM-E/RIPDM-E/R
Black 2-Pin connectorConnecteur Noir
de 2-pins
(+) S
tart
er 1
O
utpu
t
(+)1
2V
(+) N
eutr
al S
afet
ySw
itch
15
(-)St
arte
r 2
19
Test de voltage: 3 étatsClé OFF: 0 VoltsClé ON Embreyage aPark 12 VoltsClé On Embreyage aDrive: 0 Volts
Voltage Test: (3 states)Key OFF: 0 VoltsKey ON, Transmissionin Park: 12 VoltsKey ON, Transmissionin Drive: 0 Volts
IPDM-E/Rengine compartment.
sous le capot côtépassager
or passenger side enginecompartment.Sous le capotou
.
30 AMP. RELAYRELAI 30 AMP.
1A Diode
White Red Red
1 2 1
MANUAL TRANSMISSIONTRANSMISSION MANUELLE
(+) STARTRS1 OUTREMOTESTARTER
DÉMARREURÀ DISTANCE
Q50
IPDM-E/R
IPDM-E/R
Black1-Pin connector
ConnecteurNoir de 1-pins
(+) S
tart
er 1
Out
put
Red
1
engine compartment.
sous le capot côtépassager
or passenger side enginecompartment.Sous le capotou
.
WIRING CONNECTION | SCHÉMA DE BRANCHEMENTPage 4 / 7
PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION
Press and hold the programming button:Insert the 6-Pin Main connector. � The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.
Release the programming button when the BLUE LED is ON.
Relâchez le bouton de programmation quand la DEL BLEUE est allumée.
If the BLUE LED is not ON solid disconnect the 6-Pin Main connector and go back to step 1.
Si la DEL BLEUE n'est pas allumée débranchez le connecteur Principal à 6-broches et retournez au début de l'étape 1.
Insert the required remaining connectors.
2
3
4
Do not press the brake pedal.Press the Push-to-Start button twice to turn on the ignition. � The BLUE LED will flash rapidly.
5
Press the Push-to-Start button once to turn off the ignition. � will turn off.
The BLUE LED
The module is now programmed.
1
EVO-ALL_NISSANINFINITI_INDIVIDUEL_Rev3.inddNISSAN INFINIT_ AVEC RELAYS
KIA RIO - PUSH-TO-STARTREMOTE STARTER FUNCTIONNALITY | FONCTIONNALITÉS DU DÉMARREUR À DISTANCE
Remote start the vehicle.
Démarrez à distance.
START
Enter the vehicle with the Intelli-Key.
Entrez dans le véhicule avec la clé intelligente (Intelli-
Key) sur vous
The Push to Start button will turn ON
automatically.
Le bouton démarrage (Push-to-Start) du véhicule se met à Ignition (ON) automatiquement.
IGN ON
The vehicle can now be put in to gear and driven.
Vous êtes maintenant prêt à embrayer et
prendre la route.
Close the driver door.
Refermez la porte côté conducteur.
Appuyez et maintenir le bouton de programmation enfoncé: Insérez le connecteur Principal à 6-broches. � Les DELS alterneront entre un clignotement BLEU, ROUGE, JAUNE & BLEU/ROUGE.
Insérez les connecteurs requis restants.
Ne pas appuyer sur la pédale de frein.Appuyez 2 fois sur le bouton démarrage (Push-to-Start) pour allumer l'ignition. � La DEL BLEUE clignotera rapidement.
Appuyez 1 fois sur le bouton démarrage (Push-to-Start) pour éteindre l'ignition. � s'éteint.
La DEL BLEUE
Le module est programmé.
x1HOLD
A
E
F
G
J
I
H
B
C
D
LED may differ depending on the module casing.L’apparence des DELS peut différer selon le boîtier du module.
RELEASE
A
E
F
G
J
I
H
B
C
D
ONBLUE BLEU
A
E
F
G
J
I
H
B
C
D
A
E
F
G
J
I
H
B
C
D
A
E
F
G
J
I
H
B
C
D
A
E
F
G
J
I
H
B
C
D
IGN ON
x2PRESS
OFF
A EFGJ I
H B C D
IGNITION ONx1PRESS
IGNITION OFF
OFF
A
E
F
G
J
I
H
B
C
D
A EFGJ I
H B C D
IGNITION ON
ON
IGNITION OFF
FLASHRAPIDLY
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉPage 5 / 7
Remote start the vehicle.
Démarrez à distance.
All doors must be closed.
Toutes les portes
doivent être fermées
Start
Enter the vehicle with the
SMART-KEY.
Entrez dans le véhicule avec la
clé intelligente (SMART-Key)
sur vous
UNLOCK
Unlock the doors with either:
• The OEM remote • The remote-starter
remote• Or the proximity remote
Déverrouillez les portes avec soit:
• la télécommande d'origine
• la télécomande du démarreur à distance
• ou la télécommande de proximté.
The vehicle can now be put in to gear
and driven.
Vous êtes maintenant prêt à
embrayer et prendre la route.
Press the Push-to-Start button twice to turn ON
the ignition.
Appuyez 2 fois sur le bouton démarrage
(Push-to-Start) pour allumer l'ignition.
ON x2
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
REMOTE STARTER PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION DU DÉMARREUR À DISTANCE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.
RÉFÉREZ-VOUS AU GUIDE D’INSTALLATION RAPIDE INCLUS AVEC LE MODULE POUR LA PROGRAMMATION DU DÉMARREUR À DISTANCE.
REMOTE STARTER FUNCTIONNALITY | FONCTIONNALITÉS DU DÉMARREUR À DISTANCE
Page 6 / 7
Service No : 000 102 04 2536
Date: xx-xx
INTERFACE MODULE
Made in CanadaPATENTS PENDING US: 2007-228827-A1
www.fortinbypass.com
HARDWARE VERSION FIRMWARE VERSION
Module label | Étiquette sur le module
Notice: Updated Firmware and Installation GuidesUpdated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
Notice: Mise à jour microprogramme et Guides d’installationsDes mises à jour du Firmware (microprogramme) et des guides d’installation sont mis en ligne régulièrement. Vérifi ez que vous avez bien la dernière version logiciel et le dernier guide d’installation avant l’installation de ce produit.
WARNINGThe information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
MISE EN GARDE L’information de ce guide est fournie sur la base de représentation (telle quelle) sans aucune garantie de précision et d’exactitude. Il est de la seule responsabilité de l’installateur de vérifi er tous les fi ls et circuits avant d’effectuer les connexions. Seuls une sonde logique ou un multimètre digital doivent être utilisés. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité de l’exactitude de l’information fournie. L’installation (dans chaque cas) est la responsabilité de l’installateur effectuant le travail. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité suite à l’installation, que celle-ci soit bonne, mauvaise ou de n’importe autre type. Ni le manufacturier, ni le distributeur ne se considèrent responsables des dommages causés ou ayant pu être causés, indirectement ou directement, par ce module, excepté le remplacement de ce module en cas de défectuosité de fabrication. Ce module doit être installé par un technicien qualifi é. L’information fournie dans ce guide est une suggestion. Ce guide d’instruction peut faire l’objet de changement sans préavis. Consultez le www.fortinbypass.com pour voir la plus récente version.
Copyright © 2006-2014, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORTTél: 514-255-HELP (4357) 1-877-336-7797
ADDENDUM GUIDEWEB UPDATE | MISE À JOUR INTERNET
www.fortinbypass.com
ONE
Page 7 / 7