FalconStor® Hardware QuickStart Guide

Gateway Appliances (G)

www.falconstor.com

This guide supports the following models:

FS7FDSGA700F* FS7FDSCA800F*

FS7VTLGA700F* FS7VTLCA800F* FS7VTLCA801F*

FS7NSSGA700F* FS7NSSGA720F* FS7NSSGA740F*

1. Unpack the FalconStor appliance.

2. Verify the box contents. The box should contain the correct appliance, required power cords, rail kit, cable management arm kit, rack-mounting instructions, product keycode certificates, the FalconStor Software QuickStart Guide, and the CDP/NSS v7.00 Addendum for SCI Setup.The FalconStor ID and service tag are located on the Express Service Tag [EST] pullout on the appliance front panel; the service tag is also on the back panel. The Software QuickStart Guide describes how to use the Web Setup wizard to set up network configuration and passwords and enter license keys, as well as install/download client software, management consoles, and guides.

Notes: h FalconStor product keycode certificates may be shipped separately. h A monitor, keyboard, and mouse are not provided. h Two nodes are required in order to configure high availability (HA)

Contacting FalconStor Customer Support: h Support policy documents (pdfs) for your system are available at http://www.falconstor.com/support and on the FalconStor Customer Support portal (FSCS). The Technical Support Handbook describes the services available on FSCS.

h Create an account on FSCS in order to open support tickets and access all services provided by your purchased support plan.

h Open a support ticket to report damaged or missing items, as well as any problems you encounter during setup and configuration.

h Do not remove/replace hard drives or open components except under guidance from a FalconStor Technical Support representative.

1 Unpack and verify shipped materials

2 Install components in a rackInstall the rails and their respective components in a rack according to the rack-installation instructions. Allow 2 rack-mount units (2U) of vertical space for the appliance.

If your system includes Fibre Channel, connect Fibre Channel cables between your switch and the FC ports on the rear of the appliance. The Fibre Channel switch name server indicates whether or not the switch port is online.

Use two power cords to connect your appliance to a power source. Secure each cord in the nearby clip.

Use another Ethernet cable to connect your network switch to the Remote Access Controller (DRAC) connector.

Connect your network switch to the eth0 LAN port using an Ethernet cable.On CDP/NSS appliances, eth2 and eth3 are reserved for use in HA configurations and named sci0 and sci1. If you plan to configure HA, connect one end of an Ethernet cable to the sci0 port. (For HA, you will connect the servers in the cluster between sci0 and sci1 ports using two Ethernet cables.)

Connect a monitor and USB keyboard to the labeled connectors on the rear of the appliance. Tighten all screws on cable connectors.

Connect hardware components3

FS7SIRCA810F* FS7SIRCA820F* FS7SIRCA830F*

FS7CDPGA700B* FS7CDPGA720B*

This QuickStart Guide describes how to complete initial setup and configuration of your FalconStor® Gateway Appliance. Due to differences between systems, this guide may refer to components and configuration steps that do not apply to your system.

Video connector

Serial connector

USB connectors

PCIe expansion slots Power supplies and cord clips

Power supply status indicators

Service tag Fibre Channel LEDs

Optional: Connect the status indicator extension cable between the system status indicator connector and the cable management arm.

To identify an appliance in the rack, press the system ID button (7 on the front panel or on the back panel). The LCD panel (front) and system status indicator LED on the back panel flash blue until the ID button is pressed again.

Copyright © 2011 FalconStor Software. All Rights Reserved.FalconStor Software is a registered trademark of FalconStor Software, Inc. in the United States and other countries. All other brand and product names are trademarks or registered trademarks of their respective owners.FalconStor Software reserves the right to make changes to the information contained in this publication without prior notice. The reader should in all cases consult FalconStor to determine whether any such changes have been made.HQSG-G103111-EZ5-v7.00

2 Huntington QuadrangleSuite 2S01Melville, NY 11747+1 631 777 3332

www.falconstor.com

FalconStor Hardware QuickStart Guide / Gateway Appliances (G)

Thank you for purchasing a FalconStor solution!

4 Perform initial appliance configurationTo continue system configuration, open a browser from a computer that is on the same network as your appliance and go to the Web Setup address (i.e., http://10.0.0.2 or the IP address you set for eth0). The FalconStor Web Setup wizard guides you through the process of entering license keys, changing the administrator password, setting the network configuration for your appliance, and other steps that apply to the installed FalconStor solution. Depending on the solution, you will also confirm the RAID configuration for your system or choose the RAID configuration and LUN size that are appropriate for your needs.Use the FalconStor Software QuickStart Guide to help you complete the wizard, download/install client software and management consoles, and download user guides and other documentation. While in Web Setup, launch or install the FalconStor Management Console, then use the console to enable and configure additional Ethernet or SCI ports (if necessary) and configure advanced features for your software solution.

5 FalconStor Web Setup

Configure network (recommended for all products). The Network Configuration dialog is displayed on the monitor connected to the appliance. You can change the default IP address, netmask, and gateway for eth0 and IPMI/DRAC to match your existing subnets. If you do nothing, the defaults will not change. Before you continue, obtain two IP addresses from your network administrator. For eth0, the default IP address is 10.0.0.2, with the user ID root and the password IPStor101 (both are case-sensitive).

For IPMI/DRAC, the default IP address is 192.168.168.1xx, where xx repeats the last two digits of the FalconStor appliance ID (FSxxxxx), located on the EST pullout on the front panel. The default user ID is admin and the default password is falcon101 (both are case-sensitive).

When you are done, make a note of the final IP addresses.

Two command buttons are available: Reset clears any settings you may have changed, allowing you to start over. Exit displays the login prompt; use default user ID root and default password IPStor101 to log into the appliance and manually configure advanced network settings and/or network connectivity or to perform troubleshooting using standard Linux network tools.

Network Configuration Changes (after initial start-up) h For eth0 and other ethernet ports, change network/login information using Web Setup or the FalconStor Management Console.

h For a CDP or NSS appliance that will be in an HA configuration, replace default network information for sci0 and sci1 as described in the shipped CDP/NSS v7.00 Addendum for SCI Setup and the CDP/NSS Administration Guide.

h Enter the IPMI/DRAC IP address in your browser to connect to the Remote Access Controller console, where you can change network/login information and display information about appliance activity.

Power-on your system. A scan will run automatically. If any error is found, the scan will terminate and a message describing the error will be displayed. Shut down the appliance, review and repeat all connection steps, and then power-on again. If the error repeats, contact Technical Support.

Make sure all connections are secure.

Check connection indicators. If you are using Fibre Channel, the FC LEDs for your link speed (solid orange, green, or yellow) should be lit. If otherwise, contact Technical Support.

Gateway Appliance

8

9

10

1 Power-on button/indicator2 NMI button (use only if directed by Technical Support)3 Auxiliary USB connectors4 Auxiliary video connector5 LCD menu buttons < Left - Moves cursor back. Selects highlighted menu item. > Right - Moves cursor forward. To scroll messages: - Press once to increase scroll speed. - Press again to stop. - Press again to return to default scroll speed.6 LCD panel7 System ID - Turns system ID mode on and off.8 Express Service Tag (EST) pull-out9 Hard drive LEDs Upper - green = normal status; if amber, call Technical Support. Lower - blinking green = data activity. 10 Hard drives (2-6)

1 2 3 4 5 6 7