Quadratec Automatic Power Mirror Movers · The Trusted Source ® 3 Put on safety glasses. In order to install your Quadratec Powered Automatic Mirror Movers you will need to remove

The Trusted Source

®

REQUIRED TOOLS:Safety Glasses3mm Hex Key (Supplied)T40 Torx® Wrench (Supplied)Phillips ScrewdriverT20 Torx® DriverNon Marring Pry Tool Or Screwdriver6mm Hex Wrench17mm Socket & Ratchet

KIT CONTENTS LIST:Mirror Movers with Heads (L&R) Rubber Gaskets For Pillars (2)Door Fill Plate With Bumper (2) Vehicle Adapter Harness - Year Specific (2)Cable-Ties (10)

Quadratec®AutomaticPower Mirror Movers

for Jeep® Wrangler JK 2011-CurrentUS PATENT 9573526

Installation and Instruction Manual: Item #13125.023X

2011-2013 JK

2014-Current JK

Q_MIR_MVR_POWER_INST.qxp_A4 4/18/17 2:23 PM Page 1

04182017142515

The Trusted Source

®

2

READ ALL SAFETY MESSAGES AND ALWAYS WEARSAFETY GLASSES WHEN WORKING WITH TOOLS.

Before You Begin Installation: Congratulations on your purchase ofPowered Automatic Mirror Movers foryour Wrangler JK. These custom fit mir-rors have been designed for convenienceand long life. Though constructed ofonly the finest materials, these mirrorsmust be maintained and cleanedto retain their looks while performingunder the toughest conditions.

Thank you again for your purchase andlet’s start the installation process.

When unpacking, check to make sure allparts are included and not damaged dueto shipping. If any part is missing orbroken, please call us at QuadratecCustomer Service at 800-745-6037as soon as possible.

A Few Words About Product Safety: Your Powered Automatic Mirror Moversare intended to enhance the utility andof your off road capable vehicle. Beforeinstallation, please take a moment toreview the following safety

information and installation instruc-tions. Important safety information isgenerally preceded by one of threesignal words indicating the relativerisk of injury. The signal words mean:

a hazardous situation which, if not avoided, could result in death orserious injury. You CAN be KILLED or SERIOUSLY HURT if you don’tfollow instructions.

a hazardous situation which, if not avoided, could result in minor ormoderate injury. You CAN be moderately HURT and also may sufferproperty damage if you don’t follow instructions.

Careful attention is required to this instruction or operation but doesgenerally not relate to personal injury. Damage to your Quadratec®

product or other property may result if you don’t follow instructions.

Passenger Side Mirror & Fill Plate Driver Side Mirror & Fill Plate

Q_MIR_MVR_POWER_INST.qxp_A4 4/18/17 11:07 AM Page 2

04182017111031

The Trusted Source

®

3

Put on safety glasses. In order to installyour Quadratec Powered AutomaticMirror Movers you will need to removeyour factory power mirrors. Start byopening your Jeep’s driver’s side door.Locate the inner door panel. You willneed to remove this panel in order todisconnect your factory mirrors. Pleaseconsult our website for detailedinstruction on door panel removal.

A helpful video guide is available at:www.quadratec.com/power-mirror-mover-install

With door panel removed, locate thepower wires for the factory mirror,disconnect them and remove them fromany retaining clips. Your connectorsmay vary depending on the year of yourvehicle. (See FIG2)

Fig1 Fig2

Locate Two T40 Torx bolts on the insidedoor panel. Remove bolts with the sup-plied Torx wrench. Take care to supportthe mirror on the outside of door to pre-vent damaging factory mirror. Removemirror. Retain factory bolts for installa-tion of filler plates. Factory mirrors will

not be re-used. Reinstall the door panel.Locate the filler plate with bumper asshown in FIG4. The longer extensiontube goes into the bottom hole on thedoor. Insert through door into the stockmirror location. Reinstall T40 MirrorBolts into filler plate and tighten.

Fig3 Fig4

Powered Automatic Mirror Movers: Installation


04182017111031

The Trusted Source

®

4

Locate the 6 T40 Torx bolts that hold onthe windshield hinge plate. Remove all 6bolts with supplied T40 Torx wrench.Carefully remove the hinge plate and setaside. Locate the Driver’s Side PoweredMirror Mover with Wiring Harness.

You will now need to route the attachedwire harness and connector behindvehicle’s cowl as shown (Fig6). Due tomanufacturing tolerances you may needto gently pry the panel gap apart usinga non-marring pry tool or a flat bladescrewdriver wrapped in tape.

Fig5 Fig6

Pull the wire all the way under the cowland under the hood. Leave just enoughharness exposed to allow for installationof the mirror mover. (Fig7)

The next few steps may be betteraccomplished with the help of a friend.

Reinstall the factory hinge plate usingthe factory screws in the upper 4 holes.Snug using the supplied T40 Torxwrench. (Fig8)

Fig7 Fig8



04182017111032

The Trusted Source

®

5

Route the harness wire in the machinedrecess of the mirror mover before instal-lation as shown.

Place the two remaining factory screwsthrough the mounting holes in the mir-ror mover and place the gasket on thebackside of the mounting bracket asshown.

Fig9 Fig10

Tip the assembly into place and tightenthe Torx bolts using the supplied T40Torx wrench. Pull the excess harnesswire from under the cowl so that it isnot visible under the hinge plate or Mir-ror Mover Bracket. Repeat Mirror moverinstallation steps on the passenger side.

Wire harness routing and installation:Locate and remove the factory grommetshown in FIG12. Both the driver andpassenger harnesses will pass throughthis hole in the firewall. Note: FactoryHardtop models use this grommet forrear washer fluid hose.

Fig11 Fig12



04182017142516

The Trusted Source

®

6

Route the Passenger harness along thefactory loom at the back of the firewallas shown in FIG 13 and secure with thesupplied cable ties. Next, route the driv-ers’ harness to the hole in the firewall as

shown in FIG14 and secure with a sup-plied cable tie. Pass both the connectorsand harnesses through the hole in thefirewall and down into the drivers footwell.

Fig13 Fig14

Slit the factory grommet with a razorknife as shown.

Pass the new wires through the slit inthe grommet. Reinstall the grommet inthe firewall. (FIG16)

Move to the inside of the vehicle for therest of the harness installation.

Fig15 Fig16



04182017111048

The Trusted Source

®

7

Disconnect the factory door harnessconnector from underneath the dash inthe left of the driver’s footwell as shownin FIG17.

Locate the other end of the harness andremove it from its mounting location bypulling the “Christmas tree clips” free ofthe mounting holes. See FIG18.

Fig17 Fig18

Install the supplied adapter harnessbetween the factory connectors asshown and connect the Drivers side mir-ror mover harness as shown in FIG19.

Locate the harness back under the dashand install the “Christmas tree connec-tors” on the adapter harness back intothe factory mounting holes. Secure allwiring out of the way with the suppliedzip ties. Take special care not to inter-fere with operation of any of the vehiclepedals or controls.

Fig19 Fig20



04182017111048

The Trusted Source

®

8

RISK OF DEATH: SECURE WIRING HARNESSES TO AVOID INTERFERENCE WITH VEHICLE PEDALS. FAILURE TO DOSO MAY CAUSE LOSS OF VEHICLE CONTROL.

Now route the passenger side mirrormover harness from the driver’s sidefootwell over to the passenger sidefootwell. (Fig21) Remove carpet retain-ing clips and pass the harness behindthe carpet and underneath the retainingstuds. Continue to route the harness

under the carpet and behind the centerconsole. Reinstall the factory carpetand the carpet retaining clips (Fig22).DO NOT allow wiring harness or carpetto interfere with operation of pedals.Such interference could cause lossof vehicle control.

Fig21 Fig22

Continue routing the wires behind thecarpet and under the retaining posts inthe passenger footwell as shown inFIG23.

Disconnect the passenger side Factorydoor connector. Locate the other end ofthe harness & remove it from its mount-ing location by pulling the “Christmastree clips” free of the mounting holes.

Fig23 Fig24


Driver’s Side Footwell

Retaining Clip

Retaining Post

Passenger Side Footwell


04182017142516

The Trusted Source

®

9

Install the supplied adapter harness be-tween the factory connectors as shownand connect the Passenger’s side mirrormover harness as shown in FIG25.

Now locate the harness back under thedash and install the “Christmas treeconnectors” on the adapter harnessback into the factory mounting holes.Secure all wiring out of the way withthe supplied zip ties as shown in FIG26.

See next page for final adjustments.

Fig25 Fig26



04182017111049

The Trusted Source

®

10

In the event you choose to remove yourdoors, there is a convenient block-openfeature built into these mirrors. Swingthe mirror out and locate small hole onthe lower hinge assembly.

Carefully insert the supplied 3mm hexkey as shown in FIG27 and FIG28.

The 3mm hex key acts as a pin to holdthe upper hinge in place. Gently allowmirror to return and contact the hex keyas shown in FIG28. With the mirrorsblocked out of the way, the doors canbe removed without interference.

Fig27 Fig28

Powered Automatic Mirror Movers: Doors-Off Block Open Feature

Installed With Driver Door In Place Installed With Driver Door Removed


04182017142517

If your mirror is not returning properlyto the fully closed position, pull the Mir-ror mover away from the vehicle. Usinga 6mm hex key and a 17mm socket

wrench gently snug the through bolt(Fig29) until the mirror does not returnfreely to it’s resting position. Fig30shows the mirror in the no-return

The Trusted Source

®

11

Fig29 Fig30

position. Next, back off the nut on thethrough-bolt slightly (approximately ¼turn) until the mirror automatically re-turns freely and smoothly to its restingposition.

Figures 31 and 32 show the mirror beingpulled away and automatically return-ing to its resting position.

This adjustment may need to be doneperiodically throughout the life of theproduct.

Fig31 Fig32

Powered Automatic Mirror Movers: Periodic Check and Adjustments


04182017152050

The Trusted Source

®

12

Quadratec® ExclusiveThree Year Limited Warranty

Your Quadratec® branded accessories arecovered by the following Limited Warrantyprovided exclusively by Quadratec, Inc., 1028Saunders Lane, West Chester PA 19380.

This Limited Warranty is the only warrantymade in connection with your purchase.Quadratec neither assumes nor authorizes anyvendor, retailer or other person or entity to as-sume for it any other obligation or liability inconnection with this product or Limited War-ranty. This Limited Warranty does not applyand is not cumulative to any accessory or partdistributed by Quadratec for which the Manu-facturer provides a separate written warranty.

What is Covered: Subject to the terms, exclu-sions and limitations herein and with respectonly to Quadratec branded accessories first soldin the United States, Quadratec warrants to theinitial retail purchaser only that yourQuadratec accessory shall be free of defects inmaterial and workmanship: for a period ofthree (3) years from date of retail purchase.

This Limited Warranty is not assignable andshall terminate upon sale of the vehicle uponwhich the Quadratec accessory is installed orother transfer third persons.

All other warranties are hereby disclaimed, ex-cept to the extent prohibited by applicable lawin which case any implied warranty of mer-chantability or fitness for a particular purposeon this product is limited to 3 year from date ofinitial retail sale. Quadratec reserves the rightsto: (a.) require invoice or other proof your ac-cessory is within the terms of this LimitedWarranty as a condition of warranty serviceand, (b.) make future revisions to this productand Limited Warranty without prior notice orobligation to upgrade your product.

What is Not Covered:Your Quadratec Limited Warranty does notcover products or parts Quadratec determinesto have been damaged by or subjected to:

(a.) installation damage, alteration, modifica-tion, combination with other parts, failure tomaintain or improper repair or service, (b.) nor-mal wear & tear, cosmetic damage or damagefrom moisture or water immersion, (c.) Acts ofGod, accidents, misuse, negligence, inadequatemounting or impact with vehicle(s), obstaclesor other aspects of the environment, (d.) theft,vandalism or other intentional damage.

Remedy Limited to Repair/Replacement:The exclusive remedy provided hereunder shall,upon Quadratec inspection and at Quadratec’soption, be either repair or replacement of prod-uct or parts (new or refurbished) covered underthis Limited Warranty. Customers requestingwarranty consideration should first contactQuadratec to obtain a RGA number(610-701-3336). All labor, removal, shippingand installation costs are customer’s responsibility.

Other Limitations - Exclusion of Damages -Your Rights Under State Law:In consideration of the purchase price paid, nei-ther Quadratec nor any independent Quadratec distributor/licensee are responsible for any timeloss, rental costs, or for any incidental, conse-quential, punitive or other damages you mayhave or incur in connection with any part orproduct purchased. Your exclusive remedyhereunder for covered parts is repair/replace-ment as described above.

This Limited Warranty gives you specific rights.You may also have other rights that vary fromstate to state. For example, some states do notallow limitations of how long an implied war-ranty lasts and /or do not allow the exclusionor limitation of incidental or consequentialdamages, so the limitations and exclusionsherein may not apply to you.

©Quadratec, Inc. 2017. All Rights Reserved.US Patent 9573526

Instructions Part #12999.3069


04182017111051

Documents

Quadratec Automatic Power Mirror Movers · The Trusted Source ® 3 Put on safety glasses. In order to install your Quadratec Powered Automatic Mirror Movers you will need to remove