Quick Start Assembly/Install Instructions CLEARSTREAM 2 ™ WITH MOUNT Before attaching the antenna to any surface, TEST RECEPTION in that area. Connect the antenna to the TV or receiver and run a full channel scan. If reception is not as desired move the antenna and rescan TV/receiver. 1 2 3 4 5 6 7 8 9 10 11 12 Indoor Wall / Outdoor Roof Mount Tools Required: Adjustable Wrench, Power Drill, 5/16” Drill Bit, Medium-sized Cross Point Screwdriver. Thread coaxial cable through reflector (1) then hole in loop element base (2) and connect cable to connector on back of loop element (3). Secure reflector, base and loop together with 3 ½” bolt. Thread coaxial cable through reflector (1) then hole in loop element base (2) and connect cable to connector on back of loop element (3). Secure reflector, base and loop together with 3 ½” bolt. Free-Standing Indoor Use Tools Required: Adjustable Wrench 3 4 5 Place mast (4) into middle of mast base (5) and secure with 2 hex bolts. 4 1. Reﬂector 2. Loop Element Base 3. Loop Element 4. J Mount Mast 5. Mast Base 6. Plastic Base Cover 7. Circular Base 8. Hex Bolts 9. 3 ½” Bolt 10. Expansion Mounting Bolts 11. Weather Boot 12. J-mount Mast End Cap Call Our HELP LINE at 877-825-5572 One of our specialists can talk you through any problems you may have. Install antenna on mast (4) by positioning clamp on to mast. Install wing nuts but do not tighten them completely. Mark mast base position on your surface. Adjust mast so it is vertical and tighten nuts. Drill a 5/16” hole, 1½ inches deep for each mounting bolt. Insert expansion bolts and tap into position. Place base over mounting bolts, then tighten nuts to secure bolts and base to your surface. Point antenna in direction of your TV stations’ transmission towers, (to locate your towers, go to antennapoint.com or contact your local tv stations). Fully tighten wing nuts. Connect opposite end of coaxial cable to your TV or receiver. Perform channel scan and check reception. NOTE: For outside installation, we have included a weather boot (12) which can be cut to cable connector size. 1 1 2 4 Place mast (4) into middle of mast base (5) then adjust mast to vertical position and secure with 2 hex bolts. 2 4 3 3 4 Slip plastic base cover (6) over mast, nesting metal base into plastic base cover. Place mast /plastic base cover assembly on circular base (7) and snap together. 6 7 Install antenna on mast (4) by slipping clamp on back of reflector (1) over mast pipe and tighten wing nuts. Point antenna in direction of your TV stations’ transmission towers, (to locate your towers, go to antennapoint.com or contact your local tv stations). Connect the opposite end of coaxial cable to your TV or receiver. Perform channel scan and check reception. Before beginning assembly, make sure all pieces needed are present. 1 5 2 3 1 2

Quick Start Assembly/Install Instructions CLEARSTREAM 2 · of your TV stations’ transmission towers, (to locate your towers, go to antennapoint.com or contact your local tv stations)

Download PDF Report

Upload
others
View
2
Download
0

Embed Size (px)

Citation preview

Quick Start Assembly/Install Instructions

CLEARSTREAM 2™ WITH MOUNTBefore attaching the antenna to any surface, TEST RECEPTION in that area.

Connect the antenna to the TV or receiver and run a full channel scan. If reception is not as desired move the antenna and rescan TV/receiver.

Indoor Wall / Outdoor Roof MountTools Required: Adjustable Wrench, Power Drill, 5/16” Drill Bit,Medium-sized Cross Point Screwdriver.

Thread coaxial cable through reflector (1) then hole in loop element base (2) and connect cable to connector on back of loop element (3). Secure reflector, base and loop together with 3 ½” bolt.

Free-Standing Indoor UseTools Required: Adjustable Wrench

Place mast (4) into middle of mast base (5) and secure with 2 hex bolts.

1. Re�ector2. Loop Element Base3. Loop Element4. J Mount Mast5. Mast Base6. Plastic Base Cover7. Circular Base8. Hex Bolts9. 3 ½” Bolt

10. Expansion Mounting Bolts

11. Weather Boot12. J-mount Mast End Cap

Call Our HELP LINE at 877-825-5572One of our specialists can talk you through

any problems you may have.

Install antenna on mast (4) by positioning clamp on to mast. Install wing nuts but do not tighten them completely.

Mark mast base position on your surface. Adjust mast so it is vertical and tighten nuts. Drill a 5/16” hole, 1½ inches deep for each mounting bolt. Insert expansion bolts and tap into position. Place base over mounting bolts, then tighten nuts to secure bolts and base to your surface.

Point antenna in direction of your TV stations’ transmission towers, (to locate your towers, go to antennapoint.com or contact your local tv stations). Fully tighten wing nuts. Connect opposite end of coaxial cable to your TV or receiver. Perform channel scan and check reception. NOTE: For outside installation, we have included a weather boot (12) which can be cut to cable connector size.

1 1

4Place mast (4) into middle of mast base (5) then adjust mast to vertical position and secure with 2 hex bolts.

Slip plastic base cover (6) over mast, nesting metal base into plastic base cover. Place mast /plastic base cover assembly on circular base (7) and snap together.

Install antenna on mast (4) by slipping clamp on back of reflector (1) over mast pipe and tighten wing nuts.

Point antenna in direction of your TV stations’ transmission towers, (to locate your towers, go to antennapoint.com or contact your local tv stations). Connect the opposite end of coaxial cable to your TV or receiver. Perform channel scan and check reception.

Before beginning assembly, make sure all pieces needed are present.