Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Component Checklist
Installation Instructions
A. Use this configuration with a standard 50mm pole(No inserts required)
B. Use this configuration with aVisidec 42mm extrusionpole
C. Use this configuration with astandard 42mm pole
Step 1. Install Quickshift Donut
42mm Front Donut Insert (x1)
Visidec GrooveLock (x1)
42mm Rear Donut Insert (x1)
5mm AllenKey (x1)
Hardware MountingScrews
M4x10mmScrew (x4)
M4x12mmScrew (x4)
M4x16mmScrew (x4)
Select your correct product configuration: A, B, or C.
Rear Donut Insert
Rear Donut InsertFront Donut
InsertFront Donut
InsertGrooveInsert
Check you have received all parts against this Component Checklist prior to installation.
3mm AllenKey (x1)
Slide the Quickshift Donut onto the pole(with the lever open), removing the EndCap if necessary.Rear groove insert must align with slot inthe Pole.
(Visidec 42mm pole shown)
TIGHTEN
LOOSEN
Once in place, close the leverto lock the Quickshift Donutin the desired position.
Slide the Quickshift Donut into the desired position.If necessary, adjust the tension between theQuickshift Donut and the Pole using the 5mm AllenKey supplied.
Slot
OR OR
GrooveInsert
SecurityScrew (x1)(optional)
CLOSE
WARNING: Be careful not to overtighten
! The Spacedec Display Quickshift Donut is to be used on 42mm and 50mm diameter poles only.! The Manufacturer accepts no responsibility for incorrect installation.
NOTE: Phillips-headscrewdriver not supplied
Display | Quickshift Donut
QuickshiftDonut (x1)
Note: Ensure inserts are fittedin correct orientation.
Arrows pointto top surface
SD-DO
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 26.09.11 ©
Step 2. Remove VESA plate from Quickshift Donut
Step 5. Adjusting the VESA Ball Mount
Position your Display to the desired viewing angle, using the 40°angular movement allowed by the VESA Ball Mount.
Depending on the weight of the display, it may be necessary to makeadjustments to the VESA Ball Mount. If the display does not hold its position, or is too resistant, adjust the Tension Plate located at therear of the VESA Ball Mount (see diagram right).
To make any adjustments tension evenly using the 3mm Allen Key supplied. Apply half a turn at a time to each screw on the TensionPlate to adjust evenly.
Check the display, and then adjust again if necessary.
Installation Complete
Step 4. Attach your Display to the Quickshift Donut
Press and hold the Release Buttons (one on either side).
ReleaseButton
Whilst holding the Release Buttons, remove the VESA Plate.
LIFT
TIGHTEN
Hook the top of the VESA plate onto the Quickshift Mount.
(optional) Insert the Security Screw, and tighten using a Phillips-head Screwdriver.
Back of Display
VESA Plate
Loosen (-Kg)
Tighten (+Kg)
ReleaseButtons
3mm Allen Key
TensionPlate
Step 3. Attach the VESA plate to your Display
There are two mounting hole configurations:• 75 x 75mm• 100 x 100mm
Choose appropriate Mounting Screwsfrom the Hardware supplied to suityour Display. Top of
Display
Mounting Screws (x4)
VESA Plate
Back of Display
75mm(3”) 100mm
(4”)75mm
(3”)100mm
(4”)
VESA plate
Phillips-headScrewdriver
ReleaseButton
Press and hold the Release Buttons. Gentlyinsert bottom of VESA Plate into QuickshiftMount. ReleaseButtons to lockin place.