Upload
dinhlien
View
221
Download
0
Embed Size (px)
Citation preview
RAAR Enterprises, Inc.
S. California Sales Office PO Box 3476 Redondo Beach, CA 90277 USA Ph: 310-487-3800 Fx: 702-947-6320 Director: Rick Schotts Email: [email protected] DUNS #: 079-275-790 Established Since 1985/Veteran Owned www.raarenterprises.net
Okuma MILLAC 853PF-5X # 50 Taper Precision 5 Axes Vertical Profiler
Machining Center, complete with FANUC Series 31i-A5 and 120" table in
accordance with the following specifications:
Machine Specifications
Capacities: Table Size 125.95” x 33.46”
Maximum Load on Table 6,614 lbs
Spindle Nose to Table Surface 5.91” – 33.46”
Floor to Table Surface 42.52”
Spindle Center to Column Slideway 36.61”
Axis Drives: X-Axis Travel 120.1”
Y-Axis Travel 33.46”
Z-Axis Travel 27.56”
A-Axis Travel ±35°
B-Axis Travel ±35°
X-Axis Ball Screw Diameter/Pitch 2.48” / 0.42”
Y-Axis Ball Screw Diameter/Pitch 1.97” / 0.63”
Z-Axis Ball Screw Diameter/Pitch 1.97” / 0.47”
X, Y, & Z Axis Thrusts 3,527 lbs
X, Y & Z Axis Cutting Feedrates 0.039-945 ipm
A & B Axis Cutting Feed 2,400°/min
X & Y Axis Rapid Traverse Rate 1,181 ipm
Z Axis Rapid Traverse Rate 945 ipm
A & B Axis Rapid Traverse Rate 3,600°/min
Spindle: Spindle HP Rating 75 HP
Spindle Bore Taper CAT 50
Spindle Speed Range 60-12,000 RPM
Spindle Speed Change Double Wound Motor
Spindle Bearing I.D. 3.54”
Automatic Tool Changer: Magazine Capacity 30 Tools
Applicable Tool Shank CAT 50
Pull Stud P50T-II
Maximum Tool Diameter (with adjacent tools) 4.92”
Maximum Tool Diameter (without adjacent tools) 7.87”
Tool Change Time (tool to tool) 9 seconds
Tool Change Time (chip to chip) 16 seconds
Electrical: Total Power Required 116 kVA
Spindle Drive Motor AC 45/55 kW
Feed Motor X/Y/Z/A- Axis AC 7 kW
Feed Motor B-Axis (2 units) AC 3 kW
Hydraulic Pump Motor AC 2.8kW
Slideway Pump Motor AC 17 W
Coolant Pump Motor AC 1.1 kW
Chip Flushing Pump Motor AC 1.5kW
Reservoirs:
Hydraulic Tank 2.64 gallons
Spindle Lubrication Tank 10.57 gallons
Slideway Lubrication Tank 3.17 gallons
Coolant Tank 317 gallons
Machine Dimensions & Weight: Height 10.83’ (129.92”)
Floor Space (Length x Depth) 28.22’ x 15.1’ (338.58” x 181.1”)
Weight 44,093 lbs3
FANUC 31i-A5 CONTROL SPECIFICATIONS
Specifications PF Series/ 31i-A5 ○: Standard
Item Specifications Drawing # Series 31i-
A5
Controlled Axes
Controllable axes expansion (each path) (including PMC axes
and Cs axes) Max 12 axes J801 O
Simultaneously controlled axes expansion (each path Max 5 axes J803 O Increment System C 0.0001mm, 0.0001°, 0.00001" J805 ■
Controlled Axes continued
Inch/Metric conversion J876 O Stored stroke check 1 O
Mirror image each axis O
Operation
Program number search O Sequence number search O
Program restart J838 O
Operation continued
Dry run O Single block O Manual reference position return O Reference position setting without DOG O Manual handle feed 1-unit 1 unit J835 O 3-dimensional manual feed S679 O
Incremental feed x1, x10, x100, x1000, x10000 O
Interpolation Functions
Nano interpolation O
Positioning G00 (Linear Interpolation type positioning
is possible) O
Single direction positioning G60 J812 O Exact stop mode G61 O Tapping mode G63 O Cutting mode G64 O Exact stop G09 O Linear interpolation O Circular interpolation O
Dwell (Second designation)
Dwell in seconds and dwell in revolution
(In case of dwell in revolution for M
system, threading, synchronous cutting
option is required)
O
Helical interpolation Circular interpolation plus max. 2 axes
linear interpolation J819 O
Smooth interpolation J777 O Nano smoothing Al contour control I or II is required S687 O
Nano smoothing 2 Al contour control I or II is required R512 O
Reference position return G28 O Reference position return check G27 O 2nd reference position return O
Item Specifications Drawing # Series 31i-
A5
Interpolation Functions continued
3 dimensional circular interpolation S673 O
Feed Function
Rapid traverse override Fo, 24,50, 100% or 0~100% (1% step) O Feed per minute O
Automatic acceleration/deceleration Rapid traverse: linear, Cutting feed:
exponential, linear O
Rapid traverse bell-shaped acceleration/deceleration O Bell-Shaped acceleration/deceleration after cutting feed
interpolation J829 O
Feedrate override 0-254% O 2nd feedrate override 0-254% J810 O Inverse time feed J715 O Jog override 0-655.34% O Automatic corner deceleration included in Al contour control I or II O
Al contour control II Look-ahead block no. is Max. 200 (Path # <=4 and axes number <=20)
S808 O
High-speed processing
Look-ahead block no. is Max. 600 Al
contour control II is required. (Path # <=2 and axes number <=12)
S809 O
Jerk control Al contour control II is required S678 O
Program Input
Optional block skip 1 O Optional block skip 9 J955 ■
Max. programmable dimension ±9 digit (R,I,J and K is ±12 digit) O Program file name 32 characters O Sequence number N8 digit O Absolute/incremental programming Combined use in the same block O Decimal point programming/pocket calculator type decimal
point programming O
Plane selection G17, G18, G19 O Coordinate system setting O Automatic coordinate system setting O Workpiece coordinate system G52-G59 J894 O
Addition of workpiece coordinate system 48-pairs 48 pairs J895 ■
Programmable data input G10 O
Programmable parameter input O Sub program call 10 folds nested O Custom macro J873 O Addition of custom macro common variables #100- #199, #500-#999 J887 ■
Canned cycle for drilling J890 O Automatic corner override J891 O Coordinate system rotation J893 O 3-dimensional coordinate system conversion J713 O Tilted working plane command S676 ■
Programmable mirror image J880 O
Item Specifications Drawing # Series 31i-
A5
Program Input continued
Tape format for FS15 J882 O
Integrated Operation guidance function
Multiple command of auxiliary function 3 O Spindle orientation 1 spindle J853 O
Rigid tap J828 O
Tool function/ Tool compensation
Tool function T8 digit O Tool offset pairs (99-pairs) 99 J926 O/853PF
Tool offset pairs (200-pairs) 200 J927 O/2040,2565PF
■/853PF
Tool offset memory C Distinction between geometry ad wear, or between cutter and tool length comparison
J937 O
Tool length offset O Tool center point control S677 O Tool radius-Tool nose radius compensation J930 O 3-dimensional tool compensation J727 O Tool geometry/wear compensation J727 O Tool length measurement O Tool length compensation in tool axis direction S670 O 3-dimensional tool radius compensation S667 O Tool life management J935 ■
Addition of tool pairs for tool life management Max. 1024 pairs J936 ■
Accuracy compensation function
Backlash compensation O
Backlash compensation for each rapid traverse and cutting feed O
Smooth backlash compensation O
Stored pitch error compensation J841 O
Editing Operation
Part program storage length
2Mbyte J948 O 4Mbyte J949 ■
8Mbyte J959 ■
Number of Registerable programs expansion 1 Max 1000 programs J953 O
■: Option
Part program editing O Extended part program editing O Background editing J956 O
Memory card program edit & operation
Max 63 programs. The tool on PC is
required to convert and store files to memory card
O
Setting and Display
Current position display O Program comment display Program name 31 characters O
Item Specifications Drawing # Series 31i-
A5
Setting and Display continued
Parameter setting and display O Alarm display O Alarm history display O Operation history display O
Run hour and parts count display J971 O
Actual cutting feedrate display O Servo setting screen O Servo waveform display O Maintenance information screen O Help function O Self-diagnosis function O Periodic maintenance screen O Display of hardware and software configuration O Servo information screen O
Graphic function J972 O
Data input/output
Reader/puncher interface Reader/Puncher (Ch. 1) Interface J900 O
Fast data server Only 1 path control/option board is
required S737 O
Memory card input/output O
Screen hard copy *2 O
Interface function
Embedded Ethernet J381 O
Fast Ethernet Option board is required S707 O
MILLAC-853PF with FANUC-31i-A5 CNC Controller and USA Standard Specifications
Standard Specification - OAC USA Standard Spindle Motor VAC 45/55kw
Spindle Speed 60~12,000min-1
ATC Magazine Capacity 30 Tools Tool Shank CAT50 / Pull Stud CAT50-U Pull Stud Bolt CAT50-U (Thru Coolant Type) - 30 Sets Dual Contact Spindle Nose (BIG-PLUS) Table Size 3,200mm X 850mm Table T Slot Metric Spec. 18mm ATC Air Blow Standard Accessories Tool Release Lever @ Magazine Lubrication for Spindle Bearing: Oil-Mist Spindle Unit Cooling System (Oil Controller) Door Interlock Coolant Tank 2400L Coolant Pump 2.2Kw Extended Capacity Way Lube Tank (12L) Chip Conveyor, Hinge Type Coolant Nozzle Fish-Eye Type (4pcs) Flush Coolant for W-Shaped Stainless Oil Pan Rotary Scale Feed Back (A & B Axis) Work Light: Halogen Type / Fluorescent Light Machine Leveling Pad Full Closed Enclosure Buzzer for Alarm/Cycle Completion Tempered Glass on Front Door Auto Power Off Status Lamp for Spindle High/Low Position Status Lamp for A-Axis Half Brake On Spindle Speed / Load Meter UL Standard NFB/Circuit Protector Chip Air Blow Pre-Arrangement for Spindle Through Coolant (For 7mpa) PL Regulation Machine Lifting Hooks Manuals (Std. Book Set + CD) FANUC-31ia5 Standard Specification AI Contour Control 2 Kit 5-Axis Simultaneous Kit USA Kit Part Program Storage Size 2MB (5,120m) Number of Registered Programs Expansion 1 Inverse Time Feed Tool Offset Memory C Tool Length Compensation In Tool Axis Direction NURBS Interpolation Tilted Working Plane Command High Speed Cutting Function (OCJ Software) Tandem Control
Memory Protect Key Switch
MILLAC-853PF with FANUC-31i-A5 CNC Controller and USA Standard Specifications Interpolation type compensation.……………………………………….Included Abnormal load detection…………………………………………………Included Nano Smoothing………………………………………………………….Included
Transformer 480/220……………………………………………………..Included Including:
All standard equipment outlined in proposal Total List Price (as listed above) ....................................................... $469,000.00