Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
r a d i a n t H e a t i n g a n d c o o l i n g s y s t e m s
r a d i a n t r e a d y 3 0 e t M
inStrUCtiOn Sheet
1. Unpack the Unit
remove the radiant ready 30e from the box. take off the cover and remove the thermostat and thermostat wire.
2. Mount on the Wall
measure a minimum of 48" from the floor for the bracket location. Using a level, mount the bracket into the studs with the screws provided. note: do not use sheetrock anchors.
lift the radiant ready 30e onto the bracket and secure the unit to the wall with the screws provided.
Radiant Ready 30ETM Instruction Sheet
3. Connect the tubing
Use either the ProPeX®, Qs-style or multi-layer composite (mlc) tubing fitting method (supplied separately) to connect the tubing supply and return lines to the manifold.
note: example at left shows a Qs-style connection. For other fitting options, refer to the radiant ready 30e installation guide.
isolation Valve
manual drain Valve
4. Fill and Purge
connect the water supply to the supply manifold and connect the drain line to the return manifold. ensure all isolation valves are open. open the manual drain valve on the return manifold. ensure the supply manifold valves are open. turn each manifold valve clockwise until completely closed and then open one loop at a time to run water through and purge air from the lines. run water approximately one minute per loop or until drain water is free of air bubbles.
Uponor, inc. 5925 148th street West apple Valley, mn 55124 Usa tel: 800.321.4739Fax: 952.891.2008Web: www.uponor-usa.com
Uponor Ltd. 2000 argentia rd., Plaza 1, ste. 200mississauga, on l5n 1W1 canadatel: 888.994.7726Fax: 800.638.9517Web: www.uponor.ca
rr
30e_
is_H
214_
0511
, cop
yrig
ht ©
2011
Upo
nor.
Prin
ted
in t
he U
nite
d st
ates
m
Kt1
0007
_aa
max open
6mm3 mm 5x
5
close
max close
3 4
close
Raum-Heizkreis-DatenRoom heating circuit dataRuimte- en verwarminggroepsgegevensDonnées des pièces - circuits de chauffageDati circuito riscaldamento locale
Raum-NrRoom No.Ruimte-Nr
N° de la pièceNum. locale
Heizkreis-NrHeating circuit No.
Verwarmingsgroep nrN° du circuits de
chauffageNum. circuito
riscaldamento locale
Uponor FußbodenheizungsberechnungUponor floor heating calculationsUponor vloerverwarmingsberekeningCalculation du chauffage par le sol UponorCalcolo riscaldamento a pannelli radianti Uponor
11234
12345
485
11
4,5
VentileinstellungValve adjustment
VentielvoorinstellingRéglage de la vanneTartura della valvola
485
111,5
WassermengeQuantity of waterHoeveelheid water
Quantité d’eauQuantità di acqua
l/min
1 2 3
RohrnetzberechnungPipe system calculationsLeidingnetberekeningCalculation des circuits de tuyau
Strang 1Riser pipe 1Strang 1Conduit principal 1
Verteiler 1Distributor 1Verdeler 1Collecteur 1
Verteiler 2Distributor 2Verdeler 2Collecteur 2
Strang 2Riser pipe 2Strang 2Conduit principal 2
Verteiler 1Distributor 1Verdeler 1Collecteur 1
Verteiler 2Distributor 2Verdeler 2Collecteur 2
Ventileinstellung
Valve adjustmentVentielvoorinstelling
8
5
Ventileinstellung
Valve adjustmentVentielvoorinstelling
8
5
5
Massenstrom m in [kg/h]
Dru
ckve
rlus
t Δ
p in
[mba
r]
10
20
30
40
50
60
80
100
200
3
2,5
2
5 6
4
8
[kP
a]
300
400
500
1
2
3
4
5
6
8
10
20
30
40
50
300200 500 1000 2000 3000100
7
Medium: WasserMedium: Wasser
2
1
max open
6mm3 mm 5x
5
close
max close
3 4
close
Raum-Heizkreis-DatenRoom heating circuit dataRuimte- en verwarminggroepsgegevensDonnées des pièces - circuits de chauffageDati circuito riscaldamento locale
Raum-NrRoom No.Ruimte-Nr
N° de la pièceNum. locale
Heizkreis-NrHeating circuit No.
Verwarmingsgroep nrN° du circuits de
chauffageNum. circuito
riscaldamento locale
Uponor FußbodenheizungsberechnungUponor floor heating calculationsUponor vloerverwarmingsberekeningCalculation du chauffage par le sol UponorCalcolo riscaldamento a pannelli radianti Uponor
11234
12345
485
11
4,5
VentileinstellungValve adjustment
VentielvoorinstellingRéglage de la vanneTartura della valvola
485
111,5
WassermengeQuantity of waterHoeveelheid water
Quantité d’eauQuantità di acqua
l/min
1 2 3
RohrnetzberechnungPipe system calculationsLeidingnetberekeningCalculation des circuits de tuyau
Strang 1Riser pipe 1Strang 1Conduit principal 1
Verteiler 1Distributor 1Verdeler 1Collecteur 1
Verteiler 2Distributor 2Verdeler 2Collecteur 2
Strang 2Riser pipe 2Strang 2Conduit principal 2
Verteiler 1Distributor 1Verdeler 1Collecteur 1
Verteiler 2Distributor 2Verdeler 2Collecteur 2
Ventileinstellung
Valve adjustmentVentielvoorinstelling
8
5
Ventileinstellung
Valve adjustmentVentielvoorinstelling
8
5
5
Massenstrom m in [kg/h]
Dru
ckve
rlus
t Δ
p in
[mba
r]
10
20
30
40
50
60
80
100
200
3
2,5
2
5 6
4
8
[kP
a]
300
400
500
1
2
3
4
5
6
8
10
20
30
40
50
300200 500 1000 2000 3000100
7
Medium: WasserMedium: Wasser
2
1
5. Connect Power
Use a strain relief to connect the power cable to the unit. connect ground, l1, l2 and neutral wires. note: all wiring must comply with electrical codes and standards. Caution: disconnect electrical power to the system to prevent electrical shock and damage.
6. Wire the thermostat
connect both thermostat wires to the tt terminals on the unit.
7. Balance the Loops
Unlock and turn all manifold valves counterclockwise to fully open all loops. manually adjust the thermostat to call for heat and activate the pump. Visually check the flow meters to ensure there is flow. adjust all loops to correspond to the flow dictated by the system design by turning the individual valves clockwise.
8. Wire Outdoor reset (Optional)
if using outdoor reset, wire outdoor sensor to the ss terminals on the unit.
9. adjust Boiler Settings
the boiler can be configured for an output temperature between 85°F and 180°F (29°c and 82°c). adjust the output targets by selecting an application icon and adjusting the corresponding temperature setting (refer to the radiant ready 30e installation guide for details on the application icons and corresponding temperature settings for each application). enable outdoor reset by simply installing the outdoor temperature sensor (included with the unit) before powering the system on. When the system detects the sensor, the system will adjust its target temperature based on the outdoor temperature.
10. ensure Proper System Operation
manually adjust thermostat setting to create a call for heat.
• Verify boiler is operating. • Verify pump is operating. • Verify flow on visual flow meters. • Verify temperature on supply tubing.
11. adjust thermostat Settings
adjust thermostat to desired setpoint temperature.
terminal rh
terminal W
For details on loop balancing, boiler control settings, customization options and troubleshooting guidelines, refer to the radiant ready 30e installation Guide.