W A T E R P R O O F I N G | E N E R G Y S A V I N G

SHIELDH E A T R E F L E C T I V E C O A T I N G S

RAINO SHIELD is a water-based elastomeric thermal reflective and

insulative coating reducing the heat loading into buildin gs up to 40%. This

highly effective radiant as well as conduction barrier, heat insulation roof

coating paint is designed for maximum thermal efficiency, high reflectivity,

ultra violet resistance and years of trouble free service. It is mo st versatile

product for concrete roof / terrace applications for effective heat reflection

and insulation.

HIGH PERFORMANCE HEAT INSULATION COATING

•

•

•

Typical Reduction in Roof Temperatures

RCC terraces: 10°C to 15°CAsbestos cement sheets: 15°C to 20°C • GI

or powder coated sheets: Up to 25°C

TYPICAL APPLICATIONS : •••••••••••••

Roofs & Terrace Basements Asbestos roofs Aluminum Sheet Roofs Warehouses Corrosion Under Insulation (CUI) Commercial Buildings Sheds Mobile Modular Homes Weather resistant membrane Wood&concrete Air-Conditioned Building Mobile Homes

••

•••

Fabric embeddedmembrane Refrigerated Cold storage Facilities Walking decks&balconies tair ways&pool area Green Buildings

PRODUCT FEATURES :

SHIELDTECHNICAL PROPERTIES :

Properties Unit Standard Values

Surface Preparation

APPLICATION INSTRUTIONS

••••••

Bio-wash for killing fungus where necessary Roughen surfaces by wire brush manually. All surfaces must be clean and free from laitance, dust, dirt, oil and grease. Please check Moisture level and pH level in walls/roof/terrace/ceilings. The moisture levelshould be below 12% and pH should be in the range 7-9.

Brush away loose contamination on the substrate to be coated.

Mixing

•

•

••

become softer andeasier to mix.

Thoroughly mix the contents of containers using stirrer/mixer. Over-Mixing more than 5minutes may destroy particles, thereby reducing insulating capabilities.

Thinning/Dilution of the material using water is not recommended. Stir the paint occasionally before each use.

Turn pails upside down 8 hours prior to application. This will allow coating to

Color

Specific Gravity

Viscosity

Mix Ratio

Ph Value

Functional Cure

Water Absorption

Solid Content

Cured Hardness

Bond Strength /Pull of

Adhesion Strength

Solar Absorption

Solar Reflectance

Thermal Emittance

Solar Reflective Index (SRI)

Thermal Conductivity @20 c

Abrasion Resistance

Accelerated Weathering Test

Coverage

Application Temperature

-

-

cps@25oC

Part by

Weight

-

hrs

%

%

Shore D

N/mm2

%

%

-

-

W/m C

No Cycles

hrs

Kg/Sq.m/

Thic/No. of

Coats

° C

ASTM D 1544

ASTM D 792

ASTM D 1200-10

Manual

ASTM D 1293

ASTM D 1640

ASTM D 570

ASTM D 1353

ASTM D 2240

ASTM D 4541

ASTM E 1549

ASTM E 1549

ASTM C 1371

ASTM E 1980

ASTM E 1125-04

ASTM D 1044

ASTM G-155

-

-

Pastel, Tint, Deep, Accent basses and

brilliant White

1.1

10-15

Single

6-7

24 hrs

0.15

50-55

80

3.5

0.148

0.88

0.913

112

0.09

5000

2000

56Sq.m/20 kg / 100mic / 2 Coats

0-35 C

SHIELDPRODUCT APPLICATION :

•

•••

•

••

•

Coverage: 56 Sq.m / 20 kg / 100 mic / 2 coats

The surface should be moist/water wash before application. However avoidpuddling/ponding of water.

Apply first coat with brush on the cleaned and washed surface. Apply second coat after a gap of 1-2 Hours. After completion of full coating, it should be allowed to cure for 24 hrs. Drying time mayvary due to temperature / humidity and surface condition.

Ensure that the coated area does not come in contact with water for atleast one hour.

Apply with a quality brush, or roller. For best results, Apply when surface and ambient temperatures are above 13°C andbelow 32°C.

After completion of full coating, it should be allowed to cure for 24 hrs. Drying time mayvary due to temperature / humidity and surface condition.

APPLICATION EQUIPMENT :

EQUIPMENT NEEDED FOR SPRAY APPLICATION Application Equipments:

Airless Sprayer:

Brush:

Listed below are the general equipment guidelines for the

application of this product.

Pump Ratio: 33:1 or larger Volume: 1.5 gpm (5.7 lpm) or greater Hose: 3/8" or larger with no more than 3' of 1/4" whip. 1/2" hose recommended for Length above 50'. Tip Size: 0.017" (for tight spots) 0.019─0.023" (normal use) Pressure: Minimum of 3,000 PSI

Small Spray Applications:Please consult Monarch for the Small Application Sprayer. It is excellent for small applications and touch-ups.

Brushing is only recommended for touch-up of less than 0.5 ft2 (0.04 m2). Brushing can inhibit coating performance. Please consult Monarch for detailed brushing instructions.

LIMITATIONS :

•

•

Not recommended for immersion conditions.

Not to apply the product below 15°C and above 40°C

VIDHI GROUP OF COMPANIES603, President House, Ambawadi Circle, Ambawadi, Ahmedabad - 380 006, INDIA. T : +91 79 26420447 F : +91 79 40021283 M : +91 70960 00024 E : info@raino.in