Rationale and objective- Same as in theory

SCHEME OF TEACHING AND EXAMINATION FOR 3RD SEMESTER OF 3 YEARS DIPLOMA IN DRILLING TECHNOLOGY -DT

This scheme is valid for the student taking admission in academic session 2009-10 & 2010-11

Duration of Semester : Sixteen weeks (15+1#)

Student Contact Hours : 34hrs (Per week) Theory & Practical is of period 60 minutes each

Total Marks : 750

Sl. No Name of SubjectSubject Code

Nature of Subject

Teaching Scheme

Examination Scheme

L T PHours of

ExamFull

Marks of Subject

Internal Assessment

Final/ExternalExam/*Committee

Marks

Pass marks/Ext

Exam

Pass marks in Subject

1. Engg. Mathematics-III 301A Theory 4 0 0 3 100 20 80 28 35

2. GIS and Auto CAD DT302 Theory 4 1 0 3 100 20 80 28 35

3. Drilling Machine Drawing DT303 Theory 4 1 0 3 100 20 80 28 35

4. Electrical & Electronic Technology DT304 Theory 4 0 0 3 100 20 80 28 35

5. Geology- I DT305 Theory 4 0 0 3 100 20 80 28 356. GIS and Auto CAD DT306 Practical o o 3 3 50 10 40 16 207. Electrical & Electronic Technology DT307 Practical 0 0 3 3 50 10 40 16 208. Geology- I DT308 Practical 0 0 3 3 50 10 40 16 20

9. Drilling Machine Drawing DT309 Sessional 0 0 3 50 20 30 - 25

10. PTR (In Plant Training) DT310 Sessional One Month 50 20 30 - 25

Total Hours of Teaching per week 20 2 12Total Marks Theory : 500 Practical : 150 Sessional : 100

L : Lecture T : Tutorials P : Practical

* Committee Marks1. The practical subjects (external examination) will be evaluated by an internal committee for 40% of the full marks and 40% of the full marks by an

external committee.2. The Sessional subjects will be evaluated by an internal committee for 30% of the full marks and 30% of the full marks by an external committee.

# one week is assigned for internal assessment examinations.

ENGINEERING MATHS -III

L T P Curri. Ref. No. 301A

4 0 0

Total Contact Hours : 60 Total Marks : 100 Theory :

Theory : 60 End Term Exam : 80

I.A. : 20

RATIONALE :

Engineering Mathematics is most important for engineering students. Without this subject, it will very difficult to understand the other Engineering subjects.

Professional Mathematics is one of the subjects which is widely used in modern times. The techniques of this subject are being applied in finding an approximate value, optimal value and to develop the managing system in Industry. It will also help to develop attitude towards cost effectiveness, selection of most effective alternative methods. The Mathematical technique and modeling are so used in Industry, so it will not wrong to say that professional mathematics is an industrial mathematics.

OBJECTIVES :

On completion of subject students will be able to

1. The course will provide a student to develop

2. Managerial skill based on mathematical footing.

3. To understand the techniques and methods for Solving.

4. Engineering problems such as differential equations of higher orders in the fields of Electrical circuits, LRC Circuits etc. using Lap lace transformation and others.

TOPICS WISE DISTRIBUTION OF PERIODS

Sl. No. Topics Period

1. Numerical Technique 20

2. Statistical Technique 10

3. Fourier series 07

4. Laplace transform 07

5. Management Techniques (Linear models) 16

TOTAL 60

COURSE CONTENT :

1.0 Numerical Technique1.1 Finite Difference :-

1.1.1 Forward and backward differences,1.1.2 Kinds of operators , , , , and their relations, Factorial notation.1.1.3 Finite difference interpolation / extrapolation formulae.1.1.4 Newton’s forward formulae and Newton’s backward formulae

1.2 Numerical differentiation :-1.2.1 Newton’s forward and backward differentiation formulae.

1.3 Numerical integration :-1.3.1 Newton’s cotes quadrature formulae1.3.2 trapezoidal rule, simpson’s 1/3rd rule and Simpson’s 3/8 rule.

1.4 Numerical solution of non linear and transcendental Equations.1.4.1 Iteration method, Bisection method, Regula-Falsi method, and Newton-Raphson’s

method.1.5 Solution of linear simultaneous equation :-

1.5.1 Guassian Elimination method1.5.2 Gauss-jordan method.

2.0 Statistical Techniqe2.1 Introduction to statistics, measure of central tendencies.2.2 Mean deviation standard deviation and varience of discrete and grouped data, Assumed mean

and step deviation method.2.3 Correlation :-

2.3.1 Introduction, Correlation coefficient.2.4 Regression :-

2.4.1 Introduction, coefficient of regression.2.4.2 The two lines of regression (cases of two variables only)

2.5 Probability distribution :-2.5.1 Binomial distribution, Poisson’s distribution and normal distributions, their means, standard deviation and variances.

3.0 Fourier Series3.1 Periodic function, fourier series, even and odd function3.2 Fourier cosine and sine series, fourier series expansion of the period function.

4.0 Laplace Transform4.1 Introduction, general laplace transforms of algebric, trigonometrical and other function.4.2 Inverse laplace transformation.4.3 Application of laplace transformation in solving differential equation of second order.

5.0 Management Techniques5.1 Introduction to operations research (O.R.), steps of O.R.5.2 Linear programming problems : steps in formulation of a LPP.5.3 Mathematical modeling and solution procedure, graphical solution, examples.5.4 Solution by simplex method :-

5.4.1 Basic feasible solution (degenerate and non-degenerate) procedure including Big-M method, examples.

5.5 Transportation problem :-5.5.1 Introduction and solution procedure, finding the initial basic feasible solution by N-W

corner rule and vogels approximation method (VAM)

5.6 Assignment problem :-5.6.1 Introduction and solution, procedure fundamental theory underlying Hungarian

method.5.7 Network analysis :-

5.7.1 CPM and PERT, Introduction, basic activities, various time calculation.5.7.2 CPM to determine the optimal project schedule.5.7.3 PERT, Definition, difference CPM and PERT.5.7.4 Pessimistic time, Optimistic times, most likely times of various activities.

RECOMMENDED BOOKS:

1. Higher Engineering Mathematics by B. S. Grewal, Khanna Publisher.2. Engineering Mathematics by H. K. Das, S. Chand & Sons, New Delhi.3. Introduction to Numerical Analysis by S. S. Sastry, Prentice Hall of India.4. Operations Research by Kanti Swaroop, P. K. Gulta and Manmohan,

S. Chand & Sons, New Delhi.5. Fundamental of Mathematical Statistics by S. C. Gupta and V. K. Kapoor,

S. Chand & Sons, New Delhi.

GIS and Auto CADL T P Curri. Ref. No.: DT3024 1 0

Total Contact Hours: 75 Total Marks: 100Theory : 60Tutorial: 15 End Term Exam: 80

I.A.: 20

Rationale:

Like drawing and workshop practice, knowledge and practice of computation skill are necessary for development of professional competencies of a technician-engineer.

After learning this subject a student will be able to handle a Micro Computer independently and perform Digital transformation of raw drilling data in order to quick decision making. Students will be able to generate 3D spatial information of a drilling site in a complex geo environmental set up

Objective:

The Course will impart to the students application of computer to understand the uses of AutoCAD and GIS in drilling for decision making and to understand the spatial set up of a drilling site

PART -I- Fundamental of Geographic Information System (GIS) 30 Hrs

UNIT TOPIC/SUB-TOPIC .

1. Introduction of GIS

Define GIS, Describe benefit of GIS

Describe main function of GIS-

Mapping and visualization

Geographic data management

Data compilation and editing

Data analysis

Component of GIS-

Hardware-CPU, Monitor, Keyboard , Mouse, Printer, Digitizer, scanner

Software- data input, editing, digitizing, storage, output

2. Map

Define map,

Explain basic concept of Map

Explain classification of map

Define scale of map and its importance

Describe Method of expressing the scale

Simple statement method

Representative fraction

Graphical method

Describe method of Conversion of scale

Define Graphical scale and kind of graphical scale-plain scale, comparative scale, Diagonal scale, special SCALE

Topographical map, Nomenclature and numbering of Topographical sheet, Symbol of Cultural and administrative feature on toposheet

3. Deference between Paper Map and GIS map

Elements of GIS Data model - point, line, polygons, Attributes, vector, raster

4. Input/output- data conversion DXF,SHIP,DVD,BMP.SHAP

Map edit

Registration/digitization / vectorisation of map on the screen by opening an image / map at the background.

Editing a digitized map by adding segments or points and deleting a segments or points, joining segments, moving a vertex or a point on the segment and labeling the polygons, segments, and points.

Create database linked to the point, segment or the polygon layers of the map. The database linked to these map elements is in MS access MDB format.

5. Raster analysis

Analysis of a raster file.

basic arithmetic functions (like addition, subtraction

, etc), regrouping (class and range) of raster files and various other operations can be carried out.

Vector analysis

Display the point, segment and polygon layer of a vector map and provides various utilities to query the map, display the output on map, generate thematic and statistical maps.

6. Terrain model

Generation of DTM from contour map and calculation of slope, aspect and generates relative relief map using DTM. Point interpolation techniques: Cressman and Inverse Square Distance.

Part II Computer aided drawing & drafting 30Hrs

Computer aided drawing & drafting with reference to a well-known package like AutoCAD etc.

Workstation – stand-alone and networked, CAD packages – menu driven and easy to learn. Drawing sizes & ISO range of paper sizes, A3 argument, Advantages of CADD – speed, accuracy, neatness and easy in alteration, associatively.

CADD techniques: Subassemblies, blocks, inserts and components; nesting; parametric; layer; hierarchical approach to drawing. Drawing library.

2 – D Drawing: Drawing of elements in incremental steps line, rectangles, circles, chamfers, solid infill, cross-hatching, automatic dimensioning, removal of construction lines, Editing functions: moving, reflection, rotation, cloning, zoom and pan.

3 – D drawing: 3- D modeling-wire frame, surface, solid and general modeling, Transformation techniques – swing, till, spin, turn.

2 – D & 3 – D common features for manipulation – extension, contraction, rotation, reflection and moving.

CAD – Generated Drawing and DTP.

REFERENCE BOOKS :

Object Oriented Programming – by E. Balaguruswamy, TMH Software Engineering – by Roger S. Pressman, PHI Object Oriented Modeling & Design – by James Rumbaugh, Michael

Blaha, William Premerlani, Frederick Eddy, William Lorensen

Drilling Machine Drawing

L T P Curri. Ref. No.: DT3034 1 0

Total Contact Hours: 75 Total Marks: 100Theory : 60Tutorial: 15 End Term Exam: 80

I.A.: 20

RATIONAL:

For a technician to work efficiently he must have good knowledge of drawing so that he will be able to read, understand and draw drawing with fare skill. He will be able to draw free hand and communicate with works through drawing. The main objective of framing syllabus of machine drawing is to make the technician will train in any industry, department of sales or services, related with drilling and exploration organization.

OBJECTIVE: -

By going through the contents, a student will be able to read and understand drawing. Develop primary knowledge. Produce orthographic drawings of different machine parts. Develop skill to produce assembly drawing. Develop skill to produce detailed drawing of machine parts from assembly drawing. Drawing, to that he may be able to work in different field such as in drilling & exploration

industry/organization. Develop skill to of free land sketch.

SR. NO. Unit PERIODS

01. Representation of tolerance allowance & Fits as per I.S.I. codes 8

02. Orthographic projections of different Machine parts 8

03. Sectional views of different machine Parts (assembled) 8

04. Sectional views of different assembled Machine from supplied dissembled parts 8

05. Rivets and Riveted joints 8 06. Free hand sketching. 20

CONTENTS:

Unit -01: Representation of tolerance allowance & fit as per I. S.I codes.01.01. Types of limits, fits & tolerances.01.02. Deviations.

Unit -02: Orthographic projections of different machine parts. 02.01. Journal bearing02.02. J-hanger bearing.02.03. Wall bracket.02.04. Footstep bearing.02.05. I. C. engine parts.

Unit -03: Sectional views of different machine parts (assembled). 03.01. Bushed pedestal bearing, flange coupling & flexible couplings.03.02. Fast & Loose pulleys.03.03. Piston of two stokes & four stroke I. C. engine.03.04. Gib cottered joint, knuckle joint.03.05. Plumber blocks.03.06. Fppt-step bearing.

unit-04: Sectional views of different assembled machine from supplied dissembled parts. 04.01. Expansion joint04.02. Cross head and shoes (cross-head guider)04.03. Big end of connecting rod, crane and crane shaft.04.04. Stuffing box and gland.04.05. Boiler safety valves, deal weight, spring loaded type.

Unit -05: Rivets & Riveted joints. Shapes of rivet heads.05.01. Types of riveting, single & Double riveting.05.02. Reamer & Reamer shell.05.03. Diagonal pitch, margin, back pitch, rivet die testing and locking devices, nuts and bolts,

locking pins.

Unit –06: Free hand sketching.

06.01. Drill bits.06.02. Rigs06.03. Schematic diagram of cable drilling.06.04. I. S. engine parts.06.05. Drawing of earthing plate.06.06. Derricks06.07. Clevis and bolt06.08. Pipe wrench06.09. Chain wrench06.10. Fast & Loose pulley06.11. Connecting rod or IC engine06.12. Piston of two stroke & four stroke I. C. engine06.13. Gibe & cottered joint, knuckle joint, universal coupling06.14. Plumber blocks

06.15. Foot step bearing06.16. Schematic diagram of percussive drilling06.17. Single and double core barrels06.18. Drawing of Gate-end-box

Books Recommended :

01. Machine Drawing by P. S. Gill02. Machine Drawing by R. B. Gupta03. Machine Drawing by Nagpal04. Machine Drawing by Parkinson05 Drilling Technology by Chung C P

(4 Volumes)

Reference Books :

01. Machine Drawing by N. D. Bhatt02. Machine Drawing by Mittal & Agrawal03. Handbook of Diamond by J. D. Cummins

Drilling

ELECTRICAL AND ELECTRONICS TECHNOLOGY


Total Contact Hours: 60 Total Marks: 100Theory : 60 End Term Exam: 80

I.A.: 20

Rationale

The technician in dealing in exploration technology encounter many basic problems of electrical and electronics technology. Needless to say about the growing application of electronics to control and operate various equipments drilling and exploration technology this requires a basic knowledge of electronics and electronics technology.

Objective:

To understand the basic principles, mechanism and application of electric circuits, D. C. & A. C. machines and various measuring instruments.

To understand the basic principles of transistor, rectifier etc. To use the electricity and electronics for mining equipment.

PART A: - Electrical Technology.PART B: - Electronics Technology.

SR. NO. TOPICPART –A (Electrical Technology) 30

01. Electric circuits02. D.C. & A. C. Machines03. Measuring instruments.04. Mining Electricity

PART –B (Electronics Technology) 3001. Electronics02. Mining Electronics

CONTENTSPART – AUnit -01 : Electric circuit.

01.01. Revive of electric circuits.01.02. Simple magnetic circuits.

Unit -02 : D. C. & A. C. Machines

02.01. D. C. generators.02.02. Shunt and series & compound generators.02.03. D.C. motors

Torque, emf,, Speed control equations. Starters.

02.04. Transformer:Principle of operation uses of emf equation, losses & efficiency. Autotransformer.

02.05. A.C. Motors.Construction, production of relating magnetic field and operation of a 3- induction Motors relationship between rotor output, rotor input & Rotor copper loss, Application striping Induction and suirred cage induction motor Construction, Principle of operation and its characteristics.

02.06 Alternation Basic Principle and construction, principal of operation.

Unit -03 : Measuring Instrument.

03.01. Watt meter, energy meter.03.02. Frequency meter.03.03. Power factor meter.03.04. Megger.

Unit -04 : Mining Electricity

04.01. Electric cable, Types of cable constructional details of various types of cables, precaution in safe handling of cables.

04.02. Gate-end-box General Principle of working & safety device, Remote control, Electric layout.04.03. Signaling Arrangement – Haulage & shaft signal.

Part –B (Electronics Technology).

Unit -01 : Electronics

01.01. Introduction to Electronics Engineering, Electronics communication, Entertainment & Industry. Use of Electronics in this branch of studies – Overview in brief.

01.02. Electronic equipments as part of system. Electronic circuits and their elements. Active and passive devices, overview in brief.

01.03. Electronic materials: - Conductor, Insulator and semiconductor, P type and N type of semiconductors PN diode and its characteristics.

01.04. Transistor and CE Amplifier: Simple configuration and working principle characteristics.

01.05. Electronic functions: -Rectification, Amplification, Oscillation, Modulation, Demodulation, Display and counting (with block diagrams only). Input and output waveforms, their applications.

01.06. Elements of communication: Microphone, Receiver (speaker) and transmission media (line and wireless) Radio transmission, Antenna, Ionosphere, satellite communication.

01.07. Logic gates, seven segment display cathodes ray tube.

Unit -2 Drilling Electronics .

02.01. Sensors for Measuring temperature and pressure inside the Earth02.02. Electricity supply system on offshore drilling rig02.03. Telemetering of gases, oil, water in bore hole02.04. Bore hole Logging Devices, Their electronic Components, Circuit Deign, Repair and

Maintenance02.05. GPS, Electronic . Components, Circuit Deign, Repair and Maintenance02.06. (Surveliance) of distance measuring instruments.02.07. Electrometric distance measuring instruments.02.08. MIS system.02.09. Special Instruments.

Geology-I



I.A.: 20

Rationale

Knowledge of the rocks is essential for Drilling Engineering. The rock is the ultimate target to be drilled for various propose. Therefore Knowledge of Physical and mechanical Properties is essential for drilling professional

Objective To provide the knowledge of identification of various rocks, their formation, Structural architecture of rocks and their impact on drilling process

Unit 1 Introduction 101.1. Definition of Geology , branches of geology 1.2. Application of geology in drilling. 1.2 The Effect of rocks on the drilling Process

Unit 2 Introduction of Earth 10 2.1Seismology and interior of Earth

2.2 origin of earth

2.3 Age of Earth.

Unit 3.0 Geomorphology 10

3.1 Definition of Geomorphology

3.2 Weathering & Erosion,

3.3 Geomorphic features produced by River, Glacier, wind, Groundwater & ocean

3.4 introduction, cause, classification and geomorphic features produce by Volcanoes,

3.5 Cause of Earthquakes, seismic zones of india and world, prediction of earth quack

Unit 4 .0 Structural Geology & Geo-Dynamics. 10

4.1 Attitude of bed- Dip and Strike, procedure for measurement of dip and strike

4.2 Definition, Types & classification of Folds, Faults, Joints, Unconformity with neat sketch.

4.3 brief introduction with neat sketch to Plate Tectonics, and plate boundaries. Mid -oceanic Ridges, Trenches, Island Arc, Sea Floor spreading, Geosynclines.

Unit 5.0 Crystallography 10

5.1 Basic concepts of crystallography, including parameter indices, symmetry,

5.2 Laws of crystallography, concepts of crystal system, study of normal classes of each crystal system.

Unit 6 Mineralogy 10

Enumerate and describe the physical properties of minerals. Explain briefly the silicate structures along with diagrams. Describe physical properties of Olivine, Quartz, Feldspar and Pyroxene group of minerals.

Recommended books

1. Rutley’s Elements of Mineralogy -by Prof. H.H. Read.2. Introductions to physical Geology -by Prof. A.K. Dutta.3. Dana’s Manual of Mineralogy -by Hurtburt Cornelius (Jr.), John Wiley and Sons.4. Mineralogy. –By E.H. Kraus, W.F. Hunt and L.S. ramsdell, Mc-Graw Hill Book Co.5. Crystallography -by Wades and Mattox, Oxford and IBH Publishing House Co.6. Basic Concept of Physical Geology. –By E.W. Spencer, Oxford and IBH Publishing Co.7. Principles of Geomorphology. –By W.D. Thornbury, John Wile and Sons.8. Principles of Physical Geology. –By Arthur Holmes.9. Understanding the Earth. –By I.G. Gass, Peter J. Smith, R.C.L. Wilson.10. Physical Geology. –By Sheldon Judson, Kenneth S. Deffeyes, Robert B. Hargranes.

GIS and Auto CAD LAB

L T P Curri. Ref. No. DT306

0 0 3

Total Contact Hours : 45 Total Marks : 50 Practical :

Rationale and objective- Same as in theory

Practical

1) Draw litho log of given data using auto cad software

2) Draw cross section of given contour map using Auto cad Software

3) Draw various drilling tool and equipment using Auto cad software

4) Digitization of scanned map in GIS software

5) Layers generation using GIS software

6) Generation of contour from given data using GIS software

7) Generation of 3D digital Terrain Model of proposed drilling Site using GIS software

8) Prepare a geo environment Map of a proposed drilling site using GIS software

9) Adding GPS data with GIS layers

10) Decision making for selection of appropriate site for drilling using GIS software

End Term Exam : 40(Int. comm. :20,EXt. comm. 20)I.A. : 10

ELECTRICAL & ELECTRONIC LAB


0 0 3


LIST OF EXPERIMENTS:

1. Test Electronics components including switches, fuse, connectors, cable battery etc.2. Perform Soldering Technique in PCB.3. Determine the characteristic of junction diode.4. Determine the characteristic of Zener diode.5. Determine the input and output characteristics of CE & CB transistor configurations.6. Study FET characteristics.7. Construct HWR using different filters and to determine Ripple factor.8. Construct FWR using enter tap and Bridge rectifier different filters and to determine Ripple

factor.9. Construct & test the regulator using Zener diode.10. Construct and test of series regulator using series transistor and Zener diode.11. Study (i) fixed bias. (ii) Emitter bias. (iii) Voltage divider bias

Check and draw output waveform for sinusoidal voltage.12. Study the single stage CE amplifier (RL coupled) and determine frequency response.13. Study multi stage R-C coupled amplifier & to determine frequency response.14. Study (i) Class A Amplifier. (ii) Class B Amplifier. (iii) Class C Amplifier check the output

wave form for sinusoidal input.15. Construct & test push pull amplifier (Transformer coupled or Complementary symmetry

circuits.)16. Study (i) Hartly Oscillator, (ii) Collpit’s Oscillator. (iii) Wein Bridge Oscillator (IV) R-C

phase shift Oscillator.17. Study tuned amplifier.18. Study feedback Amplifier.


Geology –I


0 0 3


Rationale Objective – Same as given in theory

(1) Structural map element exercises—Interpretation of contours, identification in hill and valley in given contour map Cross-section drawing, determination of dip and strike from given structural map Measurement of dip & strike of beds using Brunton compass, (9)

(2) Structural drawing—fold, fault, unconformity, joints, Plate boundary. Mid oceanic Ridge, trench(9)(3) Identification of following minerals using harness scale and other tools and equipment(Stereo

zoom microscope)Quartz, feldspar, olivine, garnet, amphibole, Pyroxene

(4) Structural exercise Exercise 1, 2, 3 as on page 497and 1,2,3,4,5 0n page 505,and 1,2,3 on page 519 and 1,2,3,4 on page 525 & 526 given in structural geology( third Edition ) by M.P.Billings or similar type exercises

(5)Free hand sketch of Landforms made by river, glacial, wind

Recommended books

Same as given in theory


Drilling Machine Drawing

L T S Curri. Ref. No. DT309

0 0 3

Total Contact Hours : 45 Total Marks : 50 Sessional :

RATIONALE:-

For a technician to work efficiently he must have good knowledge of drawing so that he will be able to read. Understand and draw drawing with fare skill. He will be able to draw free hand and communicate with works through drawing. The main objective of framing syllabus of machine drawing is to make the technician will trained in any industry, department of sales or services, related with drilling and exploration organization.

OBJECTIVES:-

By going through the contents, a student will be able to read and understand drawing. Develop primary knowledge. Produce orthographic drawings of different machine parts Develop skill to produce assembly drawing. Develop skill to produce detailed drawing of machine parts from assembly drawing. Drawing, to that he may be able to work in different field such as in drilling & exploration

industry/organization. Develop skill to of free hand sketch.

SR. NO. TOPIC PERIODS NO. OF SHEETS

01. Representation of tolerance allowance (01) (0)

& Fits as per I.S.I. codes

02. Orthographic projections of different (5) (03)

Machine parts

03. Sectional views of different machine (10) (02)

Parts (assembled)

End Term Exam : -(Int. comm. :15,EXt. comm.15)I.A. : 20

04. Sectional views of different assembled (10) (04)

Machine from supplied dissembled parts

05. Rivets and Riveted joints (3) (02)

06. Free hand sketching (10) (06)

CONTENTS :

I.S.I. Codes Topic-01: Representation of Tolerance Allowance & fit as per.

01.01. Types of limits, fits & tolerances01.02. Deviations

Topic-02: Orthographic projections of different Machine parts

02.01. Journal bearing02.02. J-hanger bearing02.03. Wall bracket02.04. Foot step bearing02.05. I.C. engine

Topic-03: Sectional views of different machine parts (Assembled).

03.01. Bushed pedestal Dearing, flange coupling & flexible couplings.03.02. Fast & Loose pulleys.03.03. Piston of two stroke & four stroke I.C. Engine03.04. Gibe & collared joint, knuckle joint03.05. Plumber blocks03.06. Foot-step bearing.

Topic-04: Sectional views of different assembled machine from supplied dissembled parts.

04.01. Expansion joint04.02. Cross head04.03. Big end of connecting led04.04. Stuffing box 04.05. Eccentric, cylinder relief valve.04.06. Boiler safety valves.04.07.

Topic-05: Rivets & Riveted Joints.

05.01. Shapes of Rivet heads05.02. Types of riveting05.03. Reamer & Reamer shell05.04. Diagonal pitch, margin, back pitch, rivet die.

Topic-06: Free hand sketching.

06.01. Drill bits06.02. Pigs06.03. Scheme ting diagram of cable drilling06.04. I.C. engine06.05. Drawing of earthling plate 06.06. Derricks06.07. Clevis and bolt06.08. Pipe wrench06.09. Chain wrench06.10. Fast & Loose pulleys06.11. Connecting rod for IC Engine06.12. Piston of two stroke & four stroke I.C. engine06.13. Gibe & Gollared joint, knuckle joint, universal coupling06.14. Plumber blocks06.15. Foot step bearing06.16. Schematic diagram of percussive drilling06.17. Single and double core barrels06.18. Drawing of Gate-end-box

Books Recommended:

01. Machine Drawing by P.S. Gill

02. Machine Drawing by R.B. Gupta

03. Machine Drawing by Nagpal

04. Machine Drawing by Parkinson

05. Drilling Technology by Chung C P

(4 Volume)

Reference Books:

01. Machine Drawing by N.D. Bhatt

02. Machine Drawing by Mittal & Agrawal

03. Handbook of Diamond Drilling by J.D. Chmmins

PTR (In Plant Training )

Sessional Curri. Ref. No. DT310

Teaching scheme

Hours/week Hours/Semester Examination scheme

Full Marks

L 0 0 Internal Assessment

20

T 0 0 Final/ExternalExam/Committee Marks

30

P One Month

Total One Month Total 50

RATIONALE :-

A student is required to develop skill to synthesize the knowledge, skill and attitudes gained while going through different course. It is desirable to expose the students to the world of work to be familiar with the real life situations and understand the problem therein. The “In plant Training” is being introduced for the diploma technicians for Drilling and Exploration Technology with the above objectives in view. This course will help a student to observe how the technical, managerial, quality control, safety and other principles are being applied in real life situation. He will be able to observe how the supervisor performs day-to-day work and co-ordinate shop floor activities. The course will no doubt, be a great help in developing skills required for a diploma holder technician, and will also help in bringing attitudinal change in him.

OBJECTIVES: -

The objective of this course is following: -

A student will be able to: - Understand the working of the machines, tools and equipments more clearly. Write specifications of the machines, tools, and equipments. Learn to maintain office record. Know the process of planning, implementation and monitoring. Understand the drilling technique. Know the skills of quality control. Know the skill of maintenance management. Know the organizational setup and Rig Layout. Find out the characteristics, function, and activities of purpose Industries.

CONTENTS:

In plant Training and Visit to work - A student is required to get one months of training in any one of the organizations:

India Bureau of mines Geological Survey of India. Oil and Natural gas commission. Department of mining & Geology, Bihar. Central mine planning & design institute Ltd. Mineral Exploration Corporation. Central Ground water Board. Center of Remote Sensing, Dept. of Sc. & T., Jharkhand Indian School of Mines, Dhanbad. Steel Authority of India Ltd. Drilling and Exploration wing. CIL mines. Any other relevant fields. P.H.E.D

INPLANT TRAINING / FIELD VISIT – SCHEME (Any one of Following):

1. Study of exploratory drilling.2. Study of water-exploration technology.3. Study of Geo-technical investigation.4. Study of Mineral exploration.5. Study of petroleum exploration & drilling.6. Study of tube wells.7. Study of well logging technology.8. Organizing field camp by the Institution using Institution machinery & equipments.

REPORT WRITING FOR IN-PLANT TRAINING

This should include the following:

1. Introduction, purpose, objective.2. Layout and organization (about the organization)3. Operation & Technology lesson acquired.4. Training received (especially those Technology & Machinery which are in the curriculum

but not in the institution).5. Conclusion.

SCHEME OF TEACHING AND EXAMINATION FOR 4th SEMESTER OF 3 YEARS DIPLOMA IN DRILLING TECHNOLOGY -DT

This scheme is valid for the student taking admission in academic session 2009-10 & 2010-11

Duration of Semester : Sixteen weeks (15+1#)

Student Contact Hours : 34hrs (Per week) Theory & Practical is of period 60 minutes each

Total Marks : 750

Sl. No Name of SubjectSubject

CodeNature of Subject

Teaching Scheme

Examination Scheme

L T PHours of

ExamFull

Marks of Subject

Internal Assessment

Final/ExternalExam/*Committee

Marks

Pass marks/Ext

Exam

Pass marks in Subject

1 Mechanical Engineering DT401 Theory 4 0 0 3 100 20 80 28 35

2 Groundwater Exploration & Drilling DT402 Theory 4 0 0 3 100 20 80 28 35

3 Geo-exploration Technology DT403 Theory 4 0 0 3 100 20 80 28 35

4 Drilling Machinery DT404 Theory 4 0 0 3 100 20 80 28 35

5 Geology- II DT405 Theory 4 0 0 3 100 20 80 28 356 Mechanical Engineering DT406 Practical o o 3 3 50 10 40 16 207 Drilling Machinery DT407 Practical 0 0 3 3 50 10 40 16 208 Geology- II DT408 Practical 0 0 2 3 50 10 40 16 20

9 Groundwater Exploration & Drilling DT409 Sessional 0 0 3 - 50 20 30 - 2510 Geo-exploration Technology DT410 Sessional 0 0 3 - 50 20 30 - 25

Total Hours of Teaching per week 20 0 14Total Marks Theory : 500 Practical : 150 Sessional : 100

L : Lecture T : Tutorials P : Practical

*Committee Marks1. The practical subjects (external examination) will be evaluated by an internal committee for 40% of the full marks and 40% of the full marks by an

external committee.2. The Sessional subjects will be evaluated by an internal committee for 30% of the full marks and 30% of the full marks by an external committee.

# one week is assigned for internal assessment examinations.

Mechanical Engineering



I.A.: 20

RATIONALE :-

The technicians in drilling and exploration technology encounter many basic problems of mechanical engineering in their day-to-day life. They have to solve some problems related to mech. Engineering decision regarding mechanical parts on the spot. This requires basic knowledge of mechanical Engineering involving Applied mechanics, Fluid Mechanics etc.

OBJECTIVES :-

Since basic knowledge of thermal Engineering has been already studied in first year, so students should be able to fulfill the following objectives in this year.

Understand the applied mechanics and strength of materials and solve problems related with statics, center of Gravity, power transmission, beams, torsion etc.

Understand the Hydraulics and fluid mechanics, so that he is able to define, explain the terms related with the topics and solve simple problems.

SR. NO. TOPIC PERIODS

Part (A) Applied mechanics and strength of material. 3001. Statics02. Center of Gravity03. Power Transmission04. Strength of MaterialPart (B) Fluid Mechanics. 3001. Fluid02. Pressure and its measurement03. Equilibrium of Floating bodies04. Basic Equation of fluid flow 05. Flow through pipes06. Flow through orifice – Cc. Cv. Dd

07. Flow through wear & notch

CONTENTS :-

Part – (A) Applied Mechanics and strength of material.

Topic-01 : Static. 01.01. Force, Resultant and Equilibrium.01.02. 01.02. Resolution into components.01.03. Triangle and Polygon of forces: Application01.04. Moment and couple: Application to levers and beams01.05. Friction, coefficient of friction, angle of friction.01.06. The function of machine, velocity ration, mechanical advantage, winch, screw jacks, pulley block, mechanical efficiency etc.

Topic-02 : Center of Gravity. 02.01. Definition and concept of center of gravity.02.02. Determination of C.G. of various sections including numerical.

Topic-03 : Power Transmission.

03.01. Power transmission through belt rope and chain including various formula and their use (derivation not required).

Topic-04 : Strength of Material. 04.01. Simple beams bending moment and shear force of cantilevers & simply supported beam

using concentred load and uniformly distributed loads only (no combination of loads) – simple problems (no derivation of formula)

04.02. Ferrous and non-ferrous material used in mining their main properties. 04.03. Rope and chains, thin pipes and cylinders, factor of safety-No derivation of formula

Explanation of the terms and application of formula is solving simple problem.

Part – B (Fluid Mechanics)Topic – 01 : Fluid (03)

01.01. Definition & characteristics of fluids, ideal fluids compressible and incompressible fluids, properties of fluid.

01.02. 01.02. Newton’s Equation of viscosity.Topic – 02 : Pressure and its Measurement 02.01. Fluid pressure at a point, Pascal’s law and transmission of fluid pressure, total pressure

head and center of pressure.02.02. 02.02. Different types of pressure and measuring devices.02.03. 02.03. Determination of total pressure and center of pressure on plane surface immersed

in liquids.02.04. Topic 03 : Equilibrium of floating bodies 03.01. Definition, types and conditions of equilibrium.03.02. 03.02. Metacentric height and its determination.03.03. 03.03. Simple problem of the equilibrium of floating bodies.Topic 04 : Basic equation of fluid flow 04.01. Types of flow – laminar and turbulent streamlines and path lines.04.02. Continuity equation and various types energy present in fluid flow.04.02. Bernoali’s Theorem-its assumptions and practical application.04.03. Momentum equation and its application.04.04. Numerical problems based on the above topics.

Topic – 05 : Flow through pipes 05.01. Classification of laminar and turbulent flow through pipes on the basis of Reynolds’s

number.05.02. Formula of loss of head due to change in diameter of pipe and friction05.03. Use of Darcy-weibagch equation, Hydraulic gradient and total energy line05.02. Simple pipeline. Numerical problems on the above topic.Topic – 06 : Flow through orifice – C c, Cv, Cd

06.01. Vena contracta Definition and relations between Cc, Cv, Cd (no derivation)

Topic – 07 : Flow through wear & Notch. 07.01. Explanation of different terms used in measurement of discharge, relation between Cd Hr

(No derivation) simple problems. Method of measurement of discharge.

Groundwater Exploration & Drilling



I.A.: 20

RATIONALE :-

Importance of groundwater has increased considerably because of its reliability, sustainability for irrigational and Industrial uses and purity for domestic and municipal purposes. Ground water development is being done by Central and State Ground water Organizations/Public Sector undertaking and Private agencies. Haphazard and unrestricted exploitation of ground water has led to over exploitation in some localized areas in India and deterioration of quality in coastal and other regions. The availability of ground water is dependent upon physiography, geological terrain and climatic condition. It is essential therefore that scientific investigation, exploration and exploitation for ground water is resorted to for judicious development of this limited fresh water resource. Since drilling for water wells in costly preposition, a tube well must be located in most potential area to ensure success of the tube well, Here it is very important to understand that the construction of tube well and the well assembly must be such as to extract the optimum quantity on a long term sustained basis.

OBJECTIVES: To identify the potential areas by different prospecting methods. To suggest suitable ground water structure like dug well-bored well/cavity well, tub well etc. To undertake exploratory drilling and methodology for constructing tube well. To collect water samples for quality determination. To monitor development of ground water. To monitor development of ground water. To do periodic water level measurements and periodic quality determination to keep record of

behavior of water table/piezometric level and progressive quality deterioration, if any.Theory No. of Lectures

01.01. Ground water occurrence and flow 12

01.01.01. Ground water occurrence in(a) alluvial areas(b) Semi consolidated areas

(c) Consolidated areas(d) Costal areas.

01.01.02. Ground water flow Effluent and Influent

01.02. Ground water structures 8

01.02.01. Dug well, bored well, cavity well.01.02.02. Tube wells-(a) low duty, (b) Heavy duty.01.02.03. Yield capacity of wells

01.03. Explanatory Drilling 1601.03.01. Types of drilling in different rock types.01.03.02. Drilling & sampling01.03.03. Well logging (by electrical logging)01.03.04. Preparation of lithological log and importance of preservation of litholog.01.03.05. Design of well assembly01.03.06. Development of wells & field determination V-notch, Orifice – method01.03.07. Pumping tests.01.04. Ground water Development 14

01.04.01. Development trend01.04.02. Importance of monitoring of water levels on well and piezometers.01.04.03. Periodic monitoring of water levels and trend determination.01.05. Quantity of Ground water 10

01.05.01. Physical, Chemical and bacteriological quality.01.05.02. Pollution of Ground water.01.05.03. Periodical monitoring of quality of ground water.

Reference Books Recommended1. Ground water Hydrology -by D.K. Todd, John wiley & sons, New Yark.2. Ground water -by C.F. Tolman, Mc-Grow Hill Book Co. Inc. New Yark.3. Hydrology -by K.R. Karanth, Tata Mc-Grow Hill Publishing Co. Ltd.4. The occurrence of Ground water in the United States -by O.E. Meinser5. Electric logging Applied to ground water Exploration -by C.H. Ward, W. Gigel & PL Mc Casty,

John wiley & sons New Yark.6. Classification and use of irrigation waters -by D.V. Miloer, U.S. Dept. Agrl. Circular No. 9697. Ground water Drilling -by O.P. Handa, Oxford and IDH New Delhi.

Geo-exploration Technology



I.A.: 20

Rationale

The subject “Geo-exploration Technology” dealing with mineral exploration, comprises prospecting methodology, regional exploration and intensive exploration. The prospecting is carried out to find out mineral resources, while regional and intensive explorations are required for preliminary and detailed evaluations respectively of the prospects. The subject is essential for the course, since this deals with application. The subject is vast and so this is dealt with here in the following two parts.

Objective

The students after going through the course will be able to carry out prospecting in any virgins area and help in the discovery of new mineral resources.

1: Mineral Exploration 12

1.1 Definition of exploration,1.2 Methods of exploration—

Geophysical- Electrical, Gravity, Magnetic, Radioactive, Seismic Methods with detail study of equipment, working principle, data acquisition, Data interpretation and application

1.2.3 Geo-chemical Methods

1.2.4, Geo-botanical methods

1.2.4, Remote sensing and photo- geological exploration,.

2: Ore-Guides 8

5.5 Definition of guides,5.5 Classifications of guides-

Physiographic guide, Mineralogical guide, stratigraphic & lithological guide structural guides, Geo-chemical and geo-botanical guides.

3: Sampling 10

5.5 Definition of sampling, purpose and scope of sampling, factors controlling sampling, 3.2 Methods of sampling-channel, chip, grab, car, Dump, bulk, core sampling, outcrop, pit, trench

sampling. Method of reduction of sampling material-shovel or pan sampling, coring and quartering methods.

4: Reserve calculation 10

4.1 Definition of reserve and classification

4.2 Steps for reserve calculations-Determination of area of influence area calculation, thickness and volume of material determination, volume-Assay product, average thickness and average grade

4.3 Calculation methods of reserve calculation-Area of influence, Isopachyte, Isograde Methods.

5: Economic Geology 20

5.1 Definition of mineral, Ore, Refractory, Abrasive, Tenor, gangue, waste,

5.2 Formations of economic minerals and classification of economic mineral deposits.

5.3 Study of following metallic mineral deposits of India- iron, cupper, lead and zinc, Bauxite, chromites, gold, silver with reference to origin, mode of occurrence, geographic distribution, and economic importance

5.4 Study of following Non-Metallic mineral deposits of India-petroleum, mica graphite, gypsum, and beach sand with reference to origin, mode of occurrence, geographic distribution, and economic importance.

5.5 Definition of coal& coke, physical and chemical characters of coal, varieties of coal, origin of coal. Stratigraphic successions, Lithology, structure, Nature of coal seam and sedimentation pattern of Raniganj and Jharia coal fields.

Recommended books

1. Handbook for prospectors’ -by Von Bernewitz- McGraw Hill, Newyork.2. Geo-chemical prospecting for ores-by Hawkes, H.E. –Econ Geol. Vol. 44, 706-712.

3. Prospecting for Minerals-by Kitaloky, Y.D. –Foreign Langages Publishing House, Moscow.

4. Manual of Mineral Exploration - Misc. Publication G.S.I. 1975.5. Introduction to India’s Economic minerals -by Prof. N.L. Sharma and Prof. K.S.V. Ram.6. Introduction to Geology of Coal and Indian coalfields -by Sharma and Ram7. Engineering and General Geology -by Prabin Singh.

DRILLING MACHINERY



I.A.: 20

RATIONALE: -

The vast magnitude of drilling work is completed by various machinery associated with drilling technology. That is why the knowledge of various drilling systems, supporting accessories and equipments and their use and application ar4e needed, so the subject is essential for technician of drilling and exploration technology.

OBJECTIVES: -

To know the use of different drilling machineries. To know the use of drilling equipments, pumps and compressor. To know modern research and tends of development in drilling machinery.

SR. NO. TOPIC PERIODS

01. Drilling system classification 8

02. Drilling Machines. 10

03. Water pumps 10

04. Hydraulic machineries. 8

05. Air Compressors. 8

06. Drilling Accessories & equipments. 16

CONTENTS:

Topic-01 : Drilling system classification.

01.01. Introduction, type and application.

Topic-02 : Drilling Machines.

02.01. Percussion drilling machine.02.02. Diamond core drilling machine.02.03. Cable tools drilling machine. Classifications02.04. Drill machine for ground water. Working Principle,02.05. Drill machine for petroleum & Gas Applications02.06. Reverse circulatory drilling machine Specifications02.07. Hydrostatic drilling machine sketching &02.08. Anger drilling machine labeling of02.09. Jackhammer drilling machine different parts.02.10. D. T. H. & Blast-hole drilling machine

Topic-03 : Water pumps.

Reciprocating pumps

Working principle, construction, representation of process on P. V. diagram, calculation of work & efficiencies –volumetric, mechanical etc.

Air vessels, its functions, operations & maintenance.03.01. Centrifugal pumps

Working principle, construction, efficiencies mechanical, volumetric, overall etc. Operation and maintenance.

03.02. Types of pumps used for drilling industry Mud pumps, clear water pump etc.

03.03. Other types of pumps Geared pumps, jet pump, vane-pump Working principle, construction, operation and maintenance of the above.

Topic-04 : Hydraulic Machineries .

Hydraulics used in Drilling: - Nodal Analyzers pressure and energy users through pipes. Vents, nozzles etc.

Equipments. Hydraulic pump & Hydraulic motor use in drilling machines. Functions, working principles, construction, operation and maintenance. Effects of Hydraulics in drilling

Topic-05 : Air Compressors/AIR motors .

05.01. Compressed air as power05.02. Types of compressor05.02.01 . Reciprocating Compressors

Principles Construction Adiabatic compression Isothermal compression Representation of processes on P-V diagrams Calculation of work required to run a compressor Efficiency of compressor-Mechanical, volumetric, thermal & overall Inter stage cooling Effect of cooling in efficiency Operation & maintenance

05.02.02. Centrifugal compressors Types Working principles Operation and maintenance

05.02.03. Air Motor – Principle, construction and application.

Topic-06 : Drilling Accessories.

06.01. Derrick/tripod/Mast06.02. Pullies, clevis and bolt06.03. Wire ropes06.04. Lifter Sub06.05. Water swivel06.06. Delivery hoses (Water pressure holes)06.07. Suction hoses06.08. Food clamp & jaws, chuck jaws06.09. Pipe wrenches, chain wrenches, Parma lee handling tools for Drilling, wrench, rod tongues.06.10. Core barrels – single tube, double tube, swivel type rigid type triple tube.06.11. Wire line core barrels – double tube & triple tube06.12. Drill rods/ Drill pipes/ Drill collars06.12.01. Conventional drill rods (NW, BW, AW, EW, HW) and API type.06.12.02. Wire line drill rods (NO, BO, HO)06.13. Casing & couplings (NX, BX, HX, PX and others)06.14. Drill bits06.14.01. Coring – diamond & tungsten carbide bits—their method of manufacturing in brief.06.14.02. Non-coring tricone (rock roller bit) chilled shots, fish tall bits.06.14.03. DTH hammer & button bits – functions and maintenance 06.15. Reamer and Reamer shell06.16. Recovery tools/ Fishing tools.

Male and female taps (Disc collars) Right and left hand taps (Die collars)

06.17. Adopter (X-over)

06.17.01. Over shot06.17.02. Spear06.17.03. Jars06.17.04. Guides06.17.05. Wash over06.18. Drive hammers06.19. Mud mixer06.20. Slotted and blank pipes for water well06.21. Accessories required for oil & Gas drilling06.21.01. Casing and casing policy06.21.02. Well head and well completion06.21.03. Special tools & Accessories to handle high pressure and high temperature.

Books & References:

1. Manual of drilling Technology – C.P. Chung - G. S. Jain & Associates, New Delhi

2. Diamond drilling -Do- -Do-

3. Hand book of Diamond Drilling -J. D. Cummins

4. Ground Water and well drilling -Praveen Kuman -Nisha Publishers, 206,

Kamla Market,

New Delhi

5. Oil Well Drilling Technology -A.W. Mcgray -University of oklaham

& Press, Publishing

F. W. Cole division of University 1959

6. Basic Procedures for soil -W.L. Acker -Acker Drilling Co. Inc.,

Sampling & Core drilling P.O. Box-830, Seraton,

U.S.A.

7. Drilling Fluids & Composition -Gray & Darley

Geology –II



I.A.: 20

Rationale

Knowledge of the rocks is essential for Drilling Engineering. The rock is the ultimate target to be drilled for various propose. Therefore Knowledge of Physical and mechanical Properties is essential for drilling professional

Objective To provide the knowledge of identification of various rocks, their formation, Structural architecture of rocks and their impact on drilling process

Content

Unit 1.0 Petrology 20

1.1 definition of petrology and petrrography , Magma, its composition

1.2 Igneous petrology -Bowen’s Reaction principle and Diversity in Igneous Rocks

1.3 Petrography studies of common Igneous Rocks such as Granite, Pegmatite, Diorite, Granodiorite, & Gabbros, Dolerite , Basalt, Rhyolite, Trachyte, Peridotite, Dunite.

1.4 Sedimentary Petrology—Texture and structure of sedimentary rocks, Origin and classification of sedimentary rocks. Study of common sedimentary rocks such as shale, conglomerate, Breccia, Sandstone, Arkose & Lime stone.

1.5 Metamorphic petrology—Definition of Metamorphic, Concepts of Metamorphic zones, Grades & Facies. Study of common Metamorphic rocks such as Marble, Quartzite state. Phyllite, Gneiss, schist, charnockite, Khondalite, Gondite & Kodurite.

Unit 2.0 Petrology 20

2.1 Igneous petrology, Magma, its composition,

2.2 Bowen’s Reaction principle. And Diversity in Igneous Rocks

2.3 Petrography studies of common Igneous Rocks such as Granite Pegmatite, Diorite, Granodiorite, Shynite & Gabbros, Dolerite , Basalt, Rhyolite, Trachyte, Pesidotite, Dunite.

2.4 Sedimentary Petrology—Texture and structure of sedimentary rocks, Origin and classification of sedimentary rocks. Study of common sedimentary rocks such as shale, conglomerate, Breccia, Sandstone, Arkose & Lime stone.

2.5 Metamorphic petrology—Definition of Metamorphic, Concepts of Metamorphic zones, Grades & Facies. Study of common Metamorphic rocks such as Marble, Quartzite state. Phyllite, Gneiss, schist, charnockite, Khondalite, Gondite & Kodurite.

Unit 3.0 Stratigraphy & Paleontology 20

3.1 Principle of Stratigraphy.

3.2 Physiographic of division of India,

3.3 Standard Stratigraphic Code,

3.4 Important stratigraphic formation of India such as Archeons of Shinghbhum and Dharwar, Vindhyan supegroupr, Godwana supergroup & Territory with reference to their Distributions, Lithology classification, economics Importance and life.

3.5 Paleontology

8.5.1 Definition of foists, Nature and Mode of preservation

8.5.2 Uses of fossils, fossils as paleo- ecological indicators,

8.5.3 Study of important invertebrate fossils such as Brachiopoda, Pelycipoda, Gastropoda, Cephalopoda, Trilobites .

Books Recommended

The principle of petrology -by G.W. Tyrrell

A Text Book of Mineralog –by E.S. Dana and W.E. Ford, Asia Publishing House.

Kemp’s ande Hand Book of Rocks. –by F.F. Grout, D. Van Nostrand Company.

Petrography and Petrology. –by F. F. Grout, Mc-Graw Hill Book Co.

Igneous and Metamorphic Petrology. –by F.J. Turner and J. Verhoogen, Mc-Graw Hill.

Igneous Rocks and Minerals. –by E.E. Waslstrom, John Wiley and Sons.

Evolution of the Igneous Rocks. –by N.L. Bowen, Pricetan University Press.

Principles of Petrology. –by G.N. Tyrrel, Methuin and Co. Ltd.

Petrography -by H. Willians, F.J. Turner and C.M. Gilbert, Freeman Co.

Petrography. –by Howel Williams, Francis J. Turner, Charies Gilbert.

Palaentology (Invertebrate). –by Henery Wood, C.V. Press.

The Elements of Palaentology. –by R.M. Black, C.V. Press.

Invertebrate Fossils. –by Moore, Lalicher, C, Fischer, Mc-Graw Hills.

Sedimentary Rocks. –by F.J. Pettijohn, Harper, New York.

Mechanical Engineering


0 0 3


RATIONALE:-

The course is introduced to make a student develop skill to measure different parameters, record the data, draw graphs, analyses the test result and prepare a technical report.

OBJECTIVE:-

STUDENTS WILL BE ABLE TO DEVELOP SKILL TO. Measure different parameters related to experiment Verify laws which he has learnt in theory Record the data measured Analyses the test records Prepare a technical report

SR. NO TOPIC No. of Experiments PERIODS

01. Applied Mechanics & (08) 24

Strength of Materials

02. Fluid Mechanics (04) 21

Topic-01 : Applied Mechanics. (Any eight)

01.01. To draw polygon of forces and find the resultant force.01.02. To find the reaction at support of simply supported beams01.03. To find the co-efficient of friction on

a) Horizontal planeb) Inclined plane

End Term Exam : 40(Int. comm. :20,EXt. comm. :20)I.A. : 10

01.04. To find Velocity ration, mechanical advantage and mechanical efficiency of a worm and worm wheel

01.05. To find velocity ratio, Mechanical advantage and Mechanical efficiency of a double purchase winch crab

01.06. To find velocity ratio, Mechanical advantage and efficiency of a Screw jack01.07. To find velocity ration, mechanical advantage & efficiency of again & pulley system01.08. To find the G.G. with the help of a pendulum01.09. To find the Young’s modulus of elasticity of steel wire with the help of Searl’s apparatus01.10. To find the modules of rigidity through torsion

Topic-02 : Fluid Mechanics (Any Four)

02.01. To measure pressure of fluid with the help of Piezometer, U-tube.02.02. To find the buoyancy of floating body.02.03. To verify Bornoulli’s theorem02.04. To find Ce, Cu and Cd for a flow through orifice.02.05. To determine discharge of Water flowing through

b) Wear (Rectangular)c) V – notch

02.06. To find friction when water flows through pipes of different diameters.To find the Reynolds’s number of flow through of different diameters & length

Drilling Machinery


0 0 3


RATIONALE & OBJECTIVE: -

Same as in theory

TOPICWith the help of Models working as well as non-working & non functional machine.

1. Study of sketch of Hammer

2. Study of sketch of Wagon drill m/c

3. Study of sketch of DTH drill m/c

4. Study of sketch of DTH hammer & bits

5. Study of sketch of Drill bits

6. Study of sketch of Rock roller bits

7. Study of sketch of Core barrels single

8. Study of sketch of Derrick / tripods

9. Study of sketch of Fishing tools (left hand recovery rod)

10. Study of sketch of Pulley, clevis & bolts

11. Study of sketch of Wire ropes

12. Study of sketch of Foot clamp & jaws

13. Study of sketch of Reamer & reamer shell

14. Disassembly & assembly practice on non-functional machines.

Books Recommended :-Same as in theory


Geology –II


0 0 2


Rationale and Objective- same as in theory

List of practical

1. Identify the given hand specimen of rocks on the basis of their physical character.

Following rocks wii be given for identification in examination.

Igneous rock – Granite, Rhyolite, Gabbro, Syenite, Monzonie diorite, granodiorite Basalt, peridotite,

dunite, pegmatite

sedimentary rock – sandstone, limestone, shale,

Metamorphic rock –

Quartzite Marble slate, phyluite, schist gneiss, migmatite

2. Identify the mineral grains in hand specimen of rocks using zoom binocular microscope.

3. Identify the minerals in this section of rocks using polarizing microscope (Granite, basalt, dolerite may

be given in examination for identification).

4. Identify the specific gravity of given rock specimen by walker steel yard balance and Joley spring

balance (for small specimen).

5. Identify the fossils( following fossils may be given in examination )

Trilobite, foraminifera. Branchiopod, cephalopod

6. Categorized the rocks on the basis of rate of drilling (samples will be given).


7. Draw sedimentary basin on given map of India.

8. Draw Gondwana rock sequence on given map o India.

9. Draw off shore sedimentary basin of India on given map.

10. Draw important sites of petroleum and natural gas well on given map of India.

11 Field Geological Mapping

Toposheet Exercises, Plotting of Litho-unite on Toposheet Outcrop mapping of sedimentary, Igneous and Metamorphic rocks Measurement of dip and strike of bed in field. Preparation of geological map in field. Collection of rocks samples and study of their physical properties, Field mapping through GPS.

Recommended Books Field Geology by Lahee, J W &S

Manual of field Geology By Crompton

Groundwater Exploration & Drilling


0 0 3


Rationale and Objective- Same as in theory

01.01. Preparation of water table map and determination of flow direction of groundwater.01.02. Conducting yield capacity of open wells conducting pumping tests/plotting of pump test

data. Determination of permeability, transmissibility and storage co-efficient with pump test data.

01.03. Preparation of quality maps.(a) Chloride(b) Bicarbonate(c) Hardness(d) Total dissolved solids(e) Iron

01.04. Field visit to drilling site/sites to(ii) Study the actual working of water well drilling machine and accessories used

for construction of tube well.(iii) Sampling of drill cuttings, preparation of lithological log.(iv) Study operation of Electric, logger, preparation of finalilsed lithological log.(v) Design of well assembly.(vi) Lowering of assembly.(vii) Development of tube well.(viii) Discharge measurement.

Reference Books Recommended

1. Ground water Hydrology -by D.K. Todd, John wiley & sons, New Yark.2. Ground water -by C.F. Tolman, Mc-Grow Hill Book Co. Inc. New Yark.3. Hydrology -by K.R. Karanth, Tata Mc-Grow Hill Publishing Co. Ltd.

End Term Exam : -(Int. comm. :15,EXt. comm. :15)I.A. : 20

Geo-exploration Technology


0 0 3


Rational and Objective- Same as in theory

Exercises

1. Study of sub-surface geology using resistivity meter in field. or As decided by department.2. Study of Ferromagnetic dyke with the help of P.P. Magnetometer in field and data interpretation

in lab.3. Study of water table, weathered zone, thickness of soil with the help of seismic timer and data

interpretation in lab.4. Numerical exercises on Gravity, Resistivity, Seismic, Radioactivity method to understand its

practical signification.5. Study of atomic minerals in field with the help of G.M. counter and data interpretation in lab.6. Numerical exercises on reserve calculation as given in lab. To understand practical

significations.

Recommended Books Same as in theory

End Term Exam : -(Int. comm. :15,EXt. comm. :15)I.A. : 20

Documents

Rationale and objective- Same as in theory