RBS RBS 3202Concerned SoftwareUTRAN P1 SW packageToolsThis
instruction is based on following (tested and verified) SW on the
TC (Thin Client): Windows 98 (English version) including WordPad
and MS-DOS prompt. Hyper Terminal Netscape 4.7 (English version)
Java plug-in JRE 1.2.2 (English version) WS FTP ProCables required
for the connections between the TC and the RBS node: Crossed
Ethernet CAT-5 cable: RS232 (Serial) cable (RJ-45/Emily):Prepare
the Thin Client TCP/IP configuration of Thin Client.The TCP/IP
Properties window opens. Select the IP Address tab.The default node
IP configuration set at the NPC is: IP Address 169.254.1.1 Subnet
Mask 255.255.0.0The recommended IP configuration setting for the TC
is: IP Address 169.254.1.2 Subnet Mask 255.255.0.0Set up Java Java
plug in unit JRE 1.2 version C:\Program
Files\JavaSoft\JRE\1.2\lib\securityPower on the RBS node Switch on
the circuit breaker at the CU (Capacitor Unit).Connect to the RBS
node.Ethernet connection The Ethernet port of the TC must be
connected to the RBS ICF at Port T17*A, using a crossed Ethernet
cable (See section tools.). The connection is used for FTP and
Element Manager.Serial connection. The serial port (RS232) on the
TC must be connected to the RBS at GPB BB-subrack slot 20 position
A, Using a RS232 cable (See section tools.). The connection is used
for terminal programe.g. Hyper Terminal.Hyper Terminal
ConfigurationOpen the Hyper Terminal program and configure it for
direct connection via the com port (RS232) on TC.Typical
installation location:Start menu Programs Accessories
Communications Hyper TerminalThe Hyper Terminal window opens.
Double click on Hyperterm.Alternatively, open from:Start menu
RunUse Hyper Terminal connection to read out IP configuration of
the RBS node.
Command: ifconfig
Note! If no IP configuration is displayed go to section Load
UTRAN P1 SW package to node.
If the nodes IP-configuration is not set to node default, go to
the section Prepare the Thin Clientand configure the TC with an
appropriate IP-configuration.
Check IP connectivity to RBS node.The purpose of this check is
to verify that:
The IP configuration of the TC is correct. The node can be
reached via Ethernet interface.
Use MS-Dos prompt to check IP connectivity of the RBS node.
Typical installation location:Start menu Programs MS-DOS
PromptAlternatively, open from:Start menu RunThe Run window opens.
At command line, write command and click OK.The MS-DOS Prompt
window opens. Ping the node. Command: ping 169.254.1.1 Correct
results see figure MS-DOS prompt.
Load UTRAN P1 SW package to RBS node.Format the RBS node Hard
Disk.The hard disk must be formatted before loading UTRAN P1 SW
package to the node. The hard disk consists of two partitions. They
are named /c2 and /d in backup mode.
Use Hyper Terminal to format the node hard disk.
Restart node in backup mode.
Command: reload -- Format the hard disk partition /c2.
Command: formathd /c2 All data on volume will be destroyed.
Continue? y/n (n): Command: y Repeat same procedure for /d
partition.
Command: formathd /d All data on volume will be destroyed.
Continue? y/n (n): Command: y
Restart node in backup mode.
Command: reload --
Set RBS node IP configuration.The IP configuration of the node
must be set after format of the hard disc, to reach the node via
FTP program and Element manager. The IP configuration consists of
an IP address and a Subnet mask. Recommended IP configuration is
the node default set at the NPC. Use Hyper Terminal to set IP
configuration.
Command: ifconfig le0 169.254.1.1 netmask 255.255.0.0
Read out IP configuration.
Command: ifconfig Set RBS node password.Password must be set
after format of the hard disc, to be able to use FTP program.The
recommended password is rbs.
Use Hyper Terminal to set password. Command: passwd Enter new
password: Command: rbs Re-enter new password: Command: rbs Use WS
FTP Pro to download the software from TC to RBS node.
Restart RBS node.Use Hyper Terminal to restart node. Command:
reload Wait for 2-3 minutes for the node to start with CV empty.
Check all programs have been loaded (12 programs).
Command: pglist When the programs has been loaded, the green LED
on the GPB board will lid with a steady green light.
Set initial Configuration VersionSet the CV that corresponds to
the actual HW configuration in the node.Note! When CVs are
delivered a list of the different CVs will be inserted here.
Start RBS Element Manager.
