Upload
vanminh
View
240
Download
2
Embed Size (px)
Citation preview
Presenter;
Azmi Musa
SIRIM QAS INTERNATIONAL SDN. BHD.
READY-MIXED CONCRETE
CERTIFICATION & TESTING
PRESENTATION CONTENT
• About SIRIM QAS INTERNATIONAL
• Ready-Mixed Concrete
• Standards for Ready-Mixed Concrete
• Route to Ready-Mixed Concrete Certification
• Testing (SIRIM QAS INTERNATIONAL In-
house test facilities)
• Advantage of SIRIM Ready-Mixed Concrete
Certification
• Established in 1996 as a wholly-owned subsidiary of SIRIM
Berhad
• SIRIM BERHAD is a wholly-owned company of the Malaysian
Government under the Ministry of Finance Incorporated
• Have been providing conformity assessment services
since the 1970s when these services were provided as a
division of SIRIM
• Malaysian based, international accreditation and recognition
for Quality Management System, Product Certification and
Testing Services.
• Local and international clients in countries such as P.R.
China,Thailand, Singapore, Brunei, Indonesia, Vietnam,
Myanmar, Korea, Philippines, Taiwan, Japan, India, Sri
Lanka, Australia, New Zealand, Germany, UAE and Spain.
About SIRIM QAS INTERNATIONAL
About SIRIM QAS INTERNATIONAL
ur Services
CERTIFICATION
• Management System Certification
• Product Certification
• Personnel Certification
TESTING
• Product compliance testing to standards, regulatory requirements and specifications
INSPECTION
• Engineering Inspection
• Inspection on behalf of other CBs
• Other 3rd party inspections
Our Services
Ready-mixed Concrete
• Ready-mixed Concrete
Concrete manufactured in any ready-mixed concrete plant
situated at any location for delivery in a fresh state.
• Ready-mixed concrete plant
The buildings, structure and batching facilities, including
but not limited to the testing, silo, mixers, aggregate
storage facilities for production control, batching,
production, and supply of ready-mixed concrete
Standards for Ready-Mixed Concrete
• CIS 21:2016 Ready-Mixed Concrete: Production,
conformity, transportation, and delivery criteria for
producer
• MS 523:Part1:2005 = MS EN 206:2016
Concrete-Part 1:Specification, performance, production
and conformity(second revision)
• MS 523-2:2011 Concrete-Part 2: Method of specifying
and guidance for the specifier (second revision)
• MS 523-3:2010 Concrete- Part 3 Specification for
constituent materials and concrete (second revision)
• Other 32 referenced standards
ENQUIRY
APPLICATION
DOCUMENT EVALUATION
FACTORY AUDIT
SAMPLE SELECTION & TESTING
RECOMMENDATION & APPROVAL
AWARD OF LICENCE
(free publicity on Malaysiancertified)
PRODUCT CERTIFICATION SCHEME
Maintaining certification…...
SURVEILLANCE
ANNUAL RENEWAL
PRODUCT CERTIFICATION SCHEME
FACTORY ANNUAL SURVEILLANCE
ANDMARKET SAMPLING
RENEWALSUSPENSION/REVOCATION
ComplyNot Comply
MAINTAINING CERTIFICATION
The product must comply with the
requirements of the standard(s);
The manufacturer must have an acceptable
quality control plan to verify the product to
the required standard;
The manufacturer must demonstrate the
capability to comply with the Product
Certification Requirements as specified in the
Product Certification Agreement.
CRITERIA FOR THE AWARD OF LICENSE
Route to Ready-Mixed Concrete Certification
ENQUIRY
• Information supplied to client
• Feasibility for certification (standard & testing facilities) examined
• Submission of Product Certification Questionnaire form & Quotation issued
APPLICATION
• Submission of complete Product Certification Application forms
• Product descriptions – components, materials, drawings, suppliers’ certificates
• Product details – brand, model, type, rating, size
• Other applicable forms..
EVALUATION OF
DOCUMENT
• Product design evaluation against standard
• Manufacturer’s quality system document evaluation
Information required from applicant Certificate Information (Clause 8.6 of CIS 21:2016)
12
Route to Ready-Mixed Concrete Certification
FACTORY AUDIT AND SAMPLING
• Inspection conducted to examine product details, QC plan adequacy, test equipment adequacy and calibration, quality system and record-keeping system
• Samples selection and testing
INITIAL TYPE TESTING
• Type Testing in SIRIM QAS International lab OR
• Type Testing at factory lab accredited to ISO/IEC 17025
APPROVAL PROCESS
& LICENCE
• Certification Report preparation and recommendation to Certification Panel
• Approval by Certification Panel
• The license issued by SIRIM QAS International will be used by the Manufacturers / Licensees for PPS approval by CIDB
Route to Ready-Mixed Concrete Certification
SURVEILLANCE &
RE-EVALUATIONTESTING
• Planned inspections and re-tests conducted to monitor continuing compliance
• Re-evaluation test for models in license every 5 years
RENEWAL
• Approval for renewal after satisfactory surveillance audit, re-evaluation test and payment of fees.
Building 22 & 24 Materials Science Lab
Concrete And Structure
Lab
Ceramic Products Lab
Building Physics Lab
Lifting Devices Lab
Consignment Lab
CIVIL & CONSTRUCTION SECTION
(CCST)
Materials Science Lab
e.g Reinforce steel, fasteners, pipes and fittings, steel
water tanks
Concrete & Structural Lab
e.g Cement, concrete admixture, pavers, natural stones,
playground equipment
Ceramics Lab
e.g Ceramic tiles, sanitary wares, clay pipes, clay bricks,
clay roofing tiles
Building Physics
e.g Thermal insulation materials, acoustic panels, energy
efficiency glazing
Lifting Devices
Wire rope slings, chain slings, lever hoists, wire ropes
and cables
6 MAJOR LABORATORIES
SIRIM IN HOUSE TEST FACILITIES FOR
READY-MIXED CONCRETE
TEST
• Compressive strength
• Retention of consistence
(flow table or slump)
• Air content
• Resistance to penetration
• Water reduction
• Setting time
• Capillary absorption
• Bleeding
• Fluidity
• Volume change
• Tensile bond strength
SIRIM QAS INTL CEMENT AND CONCRETE LAB
MS EN 934 – 1 : 2012 / BS EN 934 – 1 : 2008
Admixture for Concrete, Mortar and Grout
Part 1 : Common Requirement
MS EN 934 – 2 : 2012 / BS EN 934 – 2 : 2009
Admixture for Concrete, Mortar and Grout
Part 2 : Concrete Admixture
MS EN 934 – 3 : 2012 / BS EN 934 – 3 : 2009
Admixture for Concrete, Mortar and Grout
Part 3 : Admixture for masonry mortar
MS EN 934 – 4 : 2012 / BS EN 934 – 4 : 2009
Admixture for Concrete, Mortar and Grout
Part 4 : Admixture for grout for prestressing tendons
MS EN 934 – 5 : 2012 / BS EN 934 – 5 : 2009
Admixture for Concrete, Mortar and Grout
Part 5 : Admixture for sprayed concrete
SIRIM QAS INTL CEMENT AND CONCRETE LAB
STRENGTH TEST
SOUNDNESS TEST
MIXING CEMENT
MS 2282-1:2014 / BS EN 771-1:2011Specification for Masonry Units. Clay Masonry Units
MS 2282-2:2014 / BS EN 771-2:2011Specification for Masonry Units. Calcium Silicate Masonry Units
MS 2282-3:2010 / BS EN 771-3:2011Specification for Masonry Units. Aggregate Concrete Masonry Units
MS 2282-4:2011 / BS EN 771-4:2011Specification for Masonry Units. Autoclaved Aerated Masonry Units
BS EN 771-5:2011Specification for Masonry Units. Manufactured Stone Masonry Units
SIRIM QAS INTL CEMENT AND CONCRETE LAB
SIRIM QAS INTL CEMENT AND CONCRETE LAB
PERMEABILITY TEST
STRENGTH TEST
23
MS ISO/IEC 17025 TESTING
ACCREDITED UNDER SAMM SCHEME BY THE
DEPARTMENT OF STANDARDS MALAYSIA (DSM)
ACCREDITATION
SIRIM IN HOUSE TEST FACILITIES FOR
READY-MIXED CONCRETE
ADVANTAGES OF SIRIM READYMIX CONCRETE CERTIFICATION
SCHEME
TO THE CONSUMER / PURCHASER
• Certified products provide the user an assurance for
safety and reliability.
• Provides more choice of safe and quality products
(among certified products).
• Provides an avenue for customer complaints and
facilitates further investigation.
24
ADVANTAGES OF SIRIM READYMIX CONCRETE CERTIFICATION
SCHEME
TO THE MANUFACTURER
• Certified products enjoy the benefits of protection
against competition from substandard products and
misrepresentation.
• The SIRIM READY-MIXED CONCRETE
CERTIFICATION SCHEME Certification Mark on a
product is an excellent marketing tool.
• Products bearing the Product Certification/Safety Mark
enhances the reputation of manufacturer and thus,
extends market and facilitates acceptance locally and
internationally.
25
ADVANTAGES OF SIRIM READYMIX CONCRETE CERTIFICATION
SCHEME
TO THE REGULATORY/ACCEPTANCE AUTHORITY
• Certification and Testing body provides reliability tools in
discharging functions and supporting technical
infrastructure.
• Overall enhancement of quality and safety in industry
and for consumer protection.
26
Contact DetailsSIRIM QAS International
PRODUCT CERTIFICATION;
1) Nor Hafeza Osman
e-mail = [email protected]
2) Wan Ahmad Jailani
e-mail = [email protected]
PRODUCT TESTING;
1) Azmi Musa
e-mail = [email protected]
2) Mohd Hanon Nazir
e-mail = [email protected]