Regulatory Information of PFXYP6MPWF (WiFi / Bluetooth

Regulatory Information of PFXYP6MPWF (WiFi / Bluetooth with antenna)
Important Information Before installing this product, read and understand the User Manual you will find in our website, https://www.pro- face.com, by searching “PS6000-MM01”. Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, or maintain it.
RF regulatory requirement for WiFi / Bluetooth board “Intel Wireless-AC 9260NGW”. Introduction Schneider Electric has validated the correct behavior of the WiFi board installed in PS6000 Series products. However, Installation or use of the WiFi board could be subject to country-specific legal regulations. As each country may have different regulatory requirements, before you install or replace the WiFi board in your PS6000 Series product, some approvals could be necessary before use. Step 1: Confirm WiFi board Regulatory Certifications Intel certified the WiFi board “Intel Wireless-AC 9260NGW” for several countries. Check through the regulatory information that the WiFi board is approved for use in your country.
“Intel Wireless-AC 9260 Regulatory Documentation”
9260_Regulatory
_Webflyer_ww04_2020_CCG.pdf
9260NGW-EU-R
TEC_RT_601282
78_0001_9260NGW.pdf
Note: Attached PDF are the ones available as of March 2nd, 2021 for your reference purpose only. Please refer to the web link provided in the next page for the latest information.
Step 2: Confirm need of system Regulatory Certifications Depending on the country, integrating the Intel WiFi board in your PS6000 Series product may require additional system tests and/or additional certifications. We suggest to contact your local authorities for further instructions and assistance. The latest information can be found in the Intel support site shown in the next page.
Page 1 of 24 December 13, 2019
Modular Regulatory Certification Country Markings (Table lists only countries requiring marking not all certified countries)
Countries
Intel® Wireless-AC 9260 (11ac / BT)
ThP2 AC + BT 2X2 – M.2
Model: 9260NGW
Model: 9260D2WL
Argentina
No
(Intel will apply CNC marking in the user guide, web flyer and
packaging
CNC
marking
and User Guide)
(Due to size constraint, marking will be in this Doc)
Intel® Corporation - CCG Intel Client Computing Group – Wireless Test & Certification Center (WTCC)
Countries
Model: 9260NGW
Model: 9260D2WL
Brazil
Yes
Module Marking: Anatel: 05831-17-04423
See Note
As it is stated in the Approval certificates there is a “vignette” (label) to be purchased by the local representative directly to the
Authority and affixed in the host equipment. The procedure is called "Application for Technical Visa". The Application form has to
be sent to the General Manager of ART. The number of stickers have to match the quantities of goods to import.
Canada
Countries
Model: 9260NGW
Model: 9260D2WL
marking will be on packaging and User Guide
9260NGW => CMIIT ID: 2017AJ4605 (M) 9260D2WL => CMIIT ID: 2019AJ2500 (M)
Comoros
No
ANRTIC 17/016/AGR/GF/DG ANRTIC 19/018/AGR/GF/DG
(OEMs must put ID on their system)
The Regulatory Marking is to be printed in a label (“vignette”)
by the importer or its local representative and affixed on the
host equipment:
The Regulatory Marking is to be printed in a label (“vignette”) by
the importer or its local representative and affixed on the host
equipment:
(Due to size constraint, full marking shall be on the
packaging label)
Countries
Model: 9260NGW
Model: 9260D2WL
NCA APPROVED: 1R3-1M-7E1-0D1 NCA APPROVED: WRG-M7-7E3-X48
India
No
9260NGW => NR-ETA/6865 and NR-ETA/6864 9260D2WL => ETA-SD-20190501118
Indonesia
No
Japan
• RF 003-170125
• TEL D170079003
• RF: 003-190024
• TEL: D190023003
TRC/SS/2019/120
Countries
Model: 9260NGW
Model: 9260D2WL
(OEMs must put ID on their system)
Note: Every importer (ie. OEM) must have a valid SIRIM certificate of the Intel module in the name of their local representative in order to sell their laptops in the Malaysia market. There is a mandatory labeling requirement for Malaysia. OEMs need to purchase the SIRIM stickers from SIRIM & stick this label on the approved product or at the back of their laptops.
Mauritania
No
Agrée par l’ARE Mauritanie
Numéro d’agrément : 0427/ARE/2017
Date d’agrément : 27/07/2017
RCPIN9217-1585 9260D2WL RCPIN9219-0324
Countries
Model: 9260NGW
Model: 9260D2WL
AGREE PAR L’ANRT MAROC
Numéro d’agrément : MR 14428 ANRT 2017
Date d’agrément : 27/07/2017
Nigeria
No
Oman
Applicant n°D080001
PTA Approved:
Connection and use of this communications equipment is permitted by the Nigerian
Communications Commission
Connection and use of this communications equipment is permitted by the Nigerian
Communications Commission
Countries
Model: 9260NGW
Model: 9260D2WL
Singapore
No
(Due to size constraint,
marking will be on packaging) It is the responsibility of the OEMs to indicate at the back of their laptop or finished
product with a statement & marking as follow: “This system contains the following wireless module: Intel 9260NGW”
It is the responsibility of the OEMs to indicate at the back of their laptop or finished product with a statement & marking as follow:
“This system contains the following wireless module: Intel 9260D2WL”
Countries
Model: 9260NGW
Model: 9260D2WL
South Africa
See note
The approval labels must be purchased by the customer’s
local representative directly from the approval authority
ICASA.
MSIP-CRM-INT-9260NGW
2. (): (
) 9260NGW
R-C-INT-9260D2WL
2. (): (
) 9260D2WL
3.: 2019/03
Taiwan
9260NGW:
9260D2WL:
Countries
Model: 9260NGW
Model: 9260D2WL
OEMs must put Intel’s Dealer
number on their system)
USA
Zambia
marking will be in this Doc)
ZMB / ZICTA / TA / 2017 / 8 /4
ZMB / ZICTA / TA / 2017 / 8 /5
Note on product label:
Due to the very small size of the Intel® Wireless-AC 9260 (Models 9260NGW & 9260D2WL), and as agreed with corresponding country authorities: some
Regulatory markings have been placed on Package box and/or in product User manual document mainly because marking affixed on the device itself is too
small to be readable.
Page left intentionally blank
Information for the User
USA—FCC and FAA
The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC
certified equipment. The wireless adapter meets the Human Exposure limits found in OET Bulletin 65, supplement C, 2001, and ANSI/IEEE C95.1, 1992. Proper
operation of this radio according to the instructions found in this manual will result in exposure substantially below the FCC’s recommended limits.
The following safety precautions should be observed:
• Do not touch or move antenna while the unit is transmitting or receiving.
• Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body, especially the face or eyes,
while transmitting.
• Do not operate the radio or attempt to transmit data unless the antenna is connected; this behavior may cause damage to the radio.
• Use in specific environments:
o The use of wireless adapters in hazardous locations is limited by the constraints posed by the safety directors of such environments.
o The use of wireless adapters on airplanes is governed by the Federal Aviation Administration (FAA) and as set forth by each airline.
o The use of wireless adapters in hospitals is restricted to the limits set forth by each hospital.
Safety Approval Considerations:
This device is for use only in complete equipment where the acceptability of the combination is determined by the appropriate safety agencies. When installed,
consideration must be given to the following:
It must be installed into a compliant host device meeting the requirement of UL/EN/IEC 60950-1 2nd edition including the general provisions of enclosure design
1.6.2 and specifically paragraph 1.2.6.2 (Fire Enclosure).
The device shall be supplied by a SELV source when installed in the end-use equipment.
A heating test shall be considered in the end-use product for meeting the requirement of UL/EN/IEC 60950-1 2nd edition.
Antenna Use
• To comply with FCC RF exposure limits, it is recommended that for the wireless adapter installed in a host computer, the low gain integrated antennas for
this device should be located at a minimum separation distance from the body of all persons as specified according to the FCC modular grant conditions.
Explosive Device Proximity Warning
Warning: Do not operate a portable transmitter (including this wireless adapter) near unshielded blasting caps or in an explosive environment unless the
transmitter has been modified to be qualified for such use.
Warning: The wireless adapter is not designed for use with high-gain directional antennas.
Use on Aircraft Caution
Caution: Regulations of the FCC, FAA and individual airlines prohibit airborne operation of some radio-frequency wireless devices (wireless adapters) because
their signals could interfere with critical aircraft instruments.
Other Wireless Devices
Safety Notices for Other Devices in the Wireless Network: See the documentation supplied with wireless adapters or other devices in the wireless network.
Local Restrictions on 802.11a, 802.11b, 802.11g, 802.11n, and 802.16e Radio Usage
Caution: Due to the fact that the frequencies used by 802.11a, 802.11b, 802.11g, 802.11n, and 802.16e wireless LAN devices may not yet be harmonized in all
countries, 802.11a, 802.11b, 802.11g, 802.11n, and 802.16e products are designed for use only in specific countries, and are not allowed to be operated in
countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which
they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. The device transmit power
control (TPC) interface is part of the Intel® PROSet/Wireless Wi-Fi Connection Utility Software. Operational restrictions for Equivalent Isotropic Radiated Power
(EIRP) are provided by the system manufacturer. Any deviation from the permissible power and frequency settings for the country of use is an infringement of
national law and may be punished as such.
For country-specific information, see the additional compliance information supplied with the product.
Wireless Interoperability
The wireless adapter is designed to be interoperable with other wireless LAN products that are based on direct sequence spread spectrum (DSSS) radio technology
and to comply with the following standards:
• IEEE Std. 802.11b compliant Standard on Wireless LAN
• IEEE Std. 802.11g compliant Standard on Wireless LAN
• IEEE Std. 802.11a compliant Standard on Wireless LAN
• IEEE Std. 802.11n draft 2.0 compliant on Wireless LAN
• IEEE 802.16e-2005 Wave 2 compliant
• Wireless Fidelity certification, as defined by the Wi-Fi Alliance
• WiMAX certification as defined by the WiMAX Forum
The Wireless Adapter and Your Health
The wireless adapter, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by the wireless adapter, however, is less
than the electromagnetic energy emitted by other wireless devices such as mobile phones. The wireless adapter operates within the guidelines found in radio
frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community and result from
deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the
use of the wireless adapter may be restricted by the proprietor of the building or responsible representatives of the applicable organization. Examples of such
situation may include:
• Using the wireless adapter on board airplanes, or
• Using the wireless adapter in any other environment where the risk of interference with other devices or services is perceived or identified as being
harmful.
If you are uncertain of the policy that applies to the use of wireless adapters in a specific organization or environment (an airport, for example), you are encouraged
to ask for authorization to use the adapter before you turn it on.
Information to Be Supplied to the End User by the OEM or Integrator
The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating the Intel® wireless
adapter, in compliance with local regulations. Host system must be labeled with "Contains FCC ID: XXXXXXXX", FCC ID displayed on label.
The Intel® wireless adapter must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes
with the product. Intel Corporation is not responsible for any radio or television interference caused by unauthorized modification of the devices included with the
wireless adapter kit or the substitution or attachment of connecting cables and equipment other than that specified by Intel Corporation. The correction of
interference caused by such unauthorized modification, substitution or attachment is the responsibility of the user. Intel Corporation and authorized resellers or
distributors are not liable for any damage or violation of government regulations that may arise from the user failing to comply with these guidelines.
Local Restriction of 802.11a, 802.11b, 802.11g, and 802.11n Radio Usage
The following statement on local restrictions must be published as part of the compliance documentation for all 802.11a, 802.11b, 802.11g and 802.11n products.
Caution: Due to the fact that the frequencies used by 802.11a, 802.11b, 802.11g, 802.11n, and 802.16e wireless LAN devices may not yet be harmonized in all
countries, 802.11a, 802.11b, 802.11g, 802.11n, and 802.16e products are designed for use only in specific countries, and are not allowed to be operated in
countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which
they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. Any deviation from the
permissible power and frequency settings for the country of use is an infringement of national law and may be punished as such.
FCC Radio Frequency Interference Requirements
This wireless adapter is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. FCC requires this wireless adapter to be used indoors
for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated
as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and /or damage this device.
• This wireless adapter is intended for OEM integrators only.
• This wireless adapter cannot be co-located with any other transmitter unless approved by the FCC based upon FCC Knowledge Database publication
number 616217 D03 (Supplement) when there are multiple radios installed in a host device, RF exposure transmitting assessment shall be performed to
determine the necessary application and test requirements. Certain criteria can be used in determine the requirement for simultaneous SAR evaluation and
whether Class I or Class II permissive change may apply. OEM integrators must consult the actual FCC KDB 616217 Supplement document for details
USA—Federal Communications Commission (FCC)
This wireless adapter complies with Part 15 of the FCC Rules. Operation of the device is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference that may cause undesired operation.
• The requirements described within this document are provided to OEM’s and system integrators installing the wireless adapter in host platforms. Strict
adherence to these requirements is necessary to meet the conditions of compliance with FCC and Industry Canada rules for RF exposure. When all
requirements described herein are fulfilled the wireless adapter may be installed in host platforms with no further RF exposure restrictions when
integrating. If any of the requirements herein are not fulfilled then additional testing and FCC/IC Permissive Changes may be required with the specific
host platform and/or antennas for compliance.
Antenna Type and Gains
• Only antennas of the same type and with equal or less gains as described in Table-1 below may be used with the wireless adapter. Other types of antennas
and/or higher gain antennas can only be authorized by Permissive Change.
• Tabel-1: Worst Case Antenna Gain Definition
Antenna
Type
Antenna
Location
(Main/Aux)
2.4GHz
3.24 3.47 3.73 4.77 4.97PIFA
Antenna Type
5.2GHz Peak gain in dBi
5.5GHz Peak gain in dBi
5.8 GHz Peak gain in dBi
Dipole
2.89
3.19
4.41
4.22
Antenna Placement • To comply with RF exposure requirements the antenna(s) used with the wireless adapter must be installed to provide a minimum separation distance from
all persons in all operating modes and orientations of the host platform as specified by the FCC grant conditions. The antenna separation distance applies
to both horizontal and vertical orientations.
Intel® Wireless Adapter Minimum required antenna-to-user separation
distance (mm) Intel® Wireless-AC 9260 (9260NGW) 14 mm Intel® Wireless-AC 9260 (9260D2WL) 19 mm
NOTE for desktop solution: To avoid the possibility of exceeding the FCC radio frequency exposure limits, a minimum distance of 20 cm separation between
persons and the external antennas must be maintained. The adapter operates below the FCC limits for radio frequency exposure, but the host system should be
installed and operated in such a manner that the potential for human contact is avoided.
Details of the authorized configurations can be found at http://www.fcc.gov/oet/ea/ by entering the FCC ID number on the device.
Interference Statement
This wireless adapter has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This wireless adapter generates, uses, and can radiate radio
frequency energy. If the wireless adapter is not installed and used in accordance with the instructions, the wireless adapter may cause harmful interference to radio
communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this wireless adapter does cause harmful
interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference
by taking one or more of the following measures:
• Reorient or relocate the receiving antenna of the equipment experiencing the interference.
• Increase the distance between the wireless adapter and the equipment experiencing the interference.
• Connect the computer with the wireless adapter to an outlet on a circuit different from that to which the equipment experiencing the interference is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: The adapter must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the
product. Any other installation or use will violate FCC Part 15 regulations.
Underwriters Laboratories Inc. (UL) Regulatory Approval
This device is UL Recognized Component for use in UL Listed personal computers or compatible equipment.
Halogen-Free Label
Some adapters are packaged with a Halogen-Free label. This claim applies only to halogenated flame retardants and PVC in components. Halogens are below 900
PPM bromine and 900 PPM chlorine.
Low Halogen: Applies only to brominated and chlorinated flame retardants (BFRs/CFRs) and PVC in the final product. Intel components as well as purchased
components on the finished assembly meet JS-709 requirements, and the PCB / substrate meet IEC 61249-2-21 requirements. The replacement of halogenated
flame retardants and/or PVC may not be better for the environment.
Radio Approvals
To determine whether you are allowed to use your wireless network device in a specific country, please check to see if the radio type number that is printed on the
identification label of your device is listed in the manufacturer's OEM Regulatory Guidance document.
Regulatory Markings
A list of required regulatory markings can be found on the web at http://www.intel.com/content/www/us/en/support/network-and-i-o/wireless-
networking/000007443.html
To find the regulatory information for your adapter, click on the link for your adapter. Then click Additional Information > Regulatory Documents.
Regulatory statement
Brazil
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode
causar interferência a sistemas operando em caráter primário.
Canada—Industry Canada (IC)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil se conforme aux normes Canada d'Industrie de RSS permis-exempt. L'utilisation est assujetti aux deux conditions suivantes: (1) cet appareil ne peut
pas causer d'interférences, et (2) cet appareil doit accepter des interférences, y compris des interférences qui peuvent causer desopérations non désirées de
l'appareil.
Caution: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use due to its operation in the 5.15- to 5.25-GHz frequency range. Industry
Canada requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel
mobile satellite systems. High power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65 to 5.85-GHz bands. These radar stations can cause
interference with and/or damage to this device. The maximum allowed antenna gain for use with this device is 6dBi in order to comply with the E.I.R.P limit for
the 5.25- to 5.35 and 5.725 to 5.85 GHz frequency range in point-to-point operation. To comply with RF exposure requirements all antennas should be located at a
minimum distance of 20cm, or the minimum separation distance allowed by the module approval, from the body of all persons.
Attention: l’utilisation d’un réseau sans fil IEEE802.11a est restreinte à une utilisation en intérieur à cause du fonctionnement dans la bande de fréquence 5.15-
5.25 GHz. Industry Canada requiert que ce produit soit utilisé à l’intérieur des bâtiments pour la bande de fréquence 5.15-5.25 GHz afin de réduire les possibilités
d’interférences nuisibles aux canaux co-existants des systèmes de transmission satellites. Les radars de puissances ont fait l’objet d’une allocation primaire de
fréquences dans les bandes 5.25-5.35 GHz et 5.65-5.85 GHz. Ces stations radar peuvent créer des interférences avec ce produit et/ou lui être nuisible. Le gain
d’antenne maximum permissible pour une utilisation avec ce produit est de 6 dBi afin d’être conforme aux limites de puissance isotropique rayonnée équivalente
(P.I.R.E.) applicable dans les bandes 5.25-5.35 GHz et 5.725-5.85 GHz en fonctionnement point-à-point. Pour se conformer aux conditions d'exposition de RF
toutes les antennes devraient être localisées à une distance minimum de 20 cm, ou la distance de séparation minimum permise par l'approbation du module, du
corps de toutes les personnes.”
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter
by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Selon les règlements de Canada d'Industrie, cet émetteur de radio peut seulement fonctionner en utilisant une antenne du type et de gain maximum (ou moindre)
que le gain approuvé pour l'émetteur par Canada d'Industrie. Pour réduire les interférences radio potentielles avec les autres utilisateurs, le type d'antenne et son
gain devraient être choisis de façon à ce que la puissance isotrope rayonnée équivalente (P.I.R.E.) ne soit pas supérieure à celle qui est nécessaire pour une
communication réussie.
European Union
The low band 5.15 -5.35 GHz is for indoor use only.
This equipment complies with the essential requirements of the European Union directive 2014/53/EU. See Statements of European Union Compliance.
European Union Declarations of Conformity.
To find the European Union Declaration of Conformity for your adapter, click on the link for your adapter.
http://www.intel.com/content/www/us/en/support/network-and-i-o/wireless-networking/000007443.html
Then select and click on the corresponding adapter: you will find Regulatory Documents in PDF format.
Japan
Korea
MSIP-CRM-INT-9260NGW
2. (): ( ) 9260NGW
3.: 2017/07
R-C-INT-9260D2WL
2. (): ( ) 9260D2WL
3.: 2019/03
Morocco
The operation of this product in the radio channel 2 (2417 MHz) is not authorized in the following cities: Agadir, Assa-Zag, Cabo Negro, Chaouen, Goulmima,
Oujda, Tan Tan, Taourirt, Taroudant and Taza.
The operation of this product in the radio channels 4, 5, 6 et 7 (2425 - 2442 MHz) is not authorized in the following cities: Aéroport Mohamed V, Agadir,
Aguelmous, Anza, Benslimane, Béni Hafida, Cabo Negro, Casablanca, Fès, Lakbab, Marrakech, Merchich, Mohammédia, Rabat, Salé, Tanger, Tan Tan,
Taounate, Tit Mellil, Zag.
Statements of European Compliance
This equipment complies with the essential requirements of the European Union directive 2014/53/EU.
[Bulgarian]: Intel® Corporation , Intel® Wireless-AC 9260
2014/53 / .
esky
[Czech]
Intel® Corporation tímto prohlašuje, e tento Intel® Wireless-AC 9260 je ve shod se základními poadavky a dalšími píslušnými
ustanoveními smrnice 2014/53/EU.
relevante krav i direktiv 2014/53/EU.
Deutsch
[German]
Hiermit erklärt Intel® Corporation, dass sich das Gerät Intel® Wireless-AC 9260 in Übereinstimmung mit den grundlegenden Anforderungen
und den übrigen einschlägigen Bestimmungen der Richtlinie 2014/53/EU befindet.
Esti
[Estonian]
direktiivist tulenevatele teistele asjakohastele sätetele.
English Hereby, Intel® Corporation, declares that this Intel® Wireless-AC 9260 is in compliance with the essential requirements and other relevant
provisions of Directive 2014/53/EU.
Español
[Spanish]
Por medio de la presente Intel® Corporation declara que el Intel® Wireless-AC 9260 & Intel® Wireless-AC 9560 cumple con los requisitos
esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 2014/53/EU.
Ελληνικ
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Intel® Corporation ΔΗΛΩΝΕΙ ΟΤΙ Intel® Wireless-AC 9260 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 2014/53/EU.
Français
[French]
Par la présente Intel® Corporation déclare que l'appareil Intel® Wireless-AC 9260 est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 2014/53/EU.
Italiano
[Italian]
Con la presente Intel® Corporation dichiara che questo Intel® Wireless-AC 9260 è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 2014/53/EU.
Latviski
[Latvian]
Ar šo Intel® Corporation deklar, ka Intel® Wireless-AC 9260 atbilst Direktvas 2014/53/EU btiskajm prasbm un citiem ar to saisttajiem
noteikumiem.
Lietuvi
[Lithuanian]
Šiuo Intel® Corporation deklaruoja, kad šis Intel® Wireless-AC 9260 atitinka esminius reikalavimus ir kitas 2014/53/EU Direktyvos nuostatas.
Nederlands
[Dutch]
Hierbij verklaart Intel® Corporation dat het toestel Intel® Wireless-AC 9260 in overeenstemming is met de essentiële eisen en de andere
relevante bepalingen van richtlijn 2014/53/EU.
Malti
[Maltese]
relevanti li hemm fid-Dirrettiva 2014/53/EU.
Magyar
[Hungarian]
Alulírott, Intel® Corporation nyilatkozom, hogy a Intel® Wireless-AC 9260 megfelel a vonatkozó alapvetõ követelményeknek és az 2014/53/EU
irányelv egyéb elõírásainak.
Norsk
[Norwegian]
Intel® Corporation erklærer herved at utstyret Intel® Wireless-AC 9260 er i samsvar med de grunnleggende krav og øvrige relevante krav i
direktiv 2014/53/EU.
Niniejszym, Intel® Corporation, owiadcza, e Intel® Wireless-AC 9260 jest zgodne z zasadniczymi wymaganiami oraz innymi stosownymi
postanowieniami Dyrektywy 2014/53/EU.
Português
[Portuguese]
Intel® Corporation declara que este Intel® Wireless-AC 9260 está conforme com os requisitos essenciais e outras disposições da Directiva
2014/53/EU.
Romãnã
[Romanian]:
Acest echipament Intel® Wireless-AC 9260 este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale Directivei 2014/53/EU.
Slovensko
[Slovenian]
Šiuo Intel® Corporation izjavlja, da je ta Intel® Wireless-AC 9260 v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive
2014/53/EU.
Slovensky
[Slovak]
Intel® Corporation týmto vyhlasuje, e Intel® Wireless-AC 9260 spa základné poiadavky a všetky príslušné ustanovenia Smernice
2014/53/EU.
Suomi
[Finnish]
Intel® Corporation vakuuttaa täten että Intel® Wireless-AC 9260 tyyppinen laite on direktiivin 2014/53/EU oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar Intel® Corporation att denna Intel® Wireless-AC 9260 står i överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 2014/53/EU.
Íslenska
[Icelandic]
Hér með lýsir Intel® Corporation yfir því að Intel® Wireless-AC 9260 er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun
2014/53/EU.
Customer Support Intel support is available online or by telephone. Available services include the most up-to-date product information, installation instructions about specific
products, and troubleshooting tips.
Network Product Support: http://www.intel.com/network
Corporate Web Site: http://www.intel.com
© Intel Corporation. All rights reserved. Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 USA
Intel Corporation S.A.S. 425 Rue de Goa – Le Cargo B6 – CS 70116 - 06605 Antibes Cedex – France
Tel. +33 (0)4 93 00 14 00 - Fax +33 (0)4 93 00 14 01 SAS au capital de 2 000 000 Euros – RCS Grasse B 527 863 039 – NAF 7219Z – Siret 527 863 039 00022 - TVA FR12527863039
EU Declaration of Conformity
Manufacturer:
Name: INTEL CORPORATION SAS Address: 425 Rue de Goa – Le Cargo B6 – 06600 Antibes Country: France
This declaration of conformity is issued under the sole responsibility of the manufacturer who declares that the above described radio equipment is in conformity with the following relevant Union harmonisation legislations:
Radio Equipment Directive 2014/53/EU (RED) RoHS2 Directive 2011/65/EU
The conformity assessment procedure used for this declaration is Annex III of RED 2014/53/EU and the product will bear the CE-Marking CE accordingly. Conformity to the essential requirements of the legislation(s) have been demonstrated by using the following standards:
Health and Safety (Art 3(1) (a)): EN 62368-1: 2014
EN 50566:2017
EMC (Art.3(1) (b)): EN 301 489-1 v2.2.0 EN 301 489-17 v3.2.0 EN 55032 :2015
Spectrum (Art.3(2)): EN 300 328 v2.2.2 EN 301 893 v2.1.1 EN 300 440 v2.2.1
RoHS2 Directive 2011/65/EU EN 50581:2012 The notified body TUV Rheinland LGA Products GmbH, Tillystrasse 2, 90431 Nuremberg / number: 0197 performed an EU-type examination and issued the EU-type examination certificate: RT 60148652 0001 The following accessory allows the object of the declaration described above to operate as intended and in conformity with this EU declaration of conformity: Software Intel PROSet/Wireless WiFi version 20.x and following versions. Signed for and on behalf of: Intel Corporation SAS Place and date of issue: Antibes, France, 16th April 2020
Signature: Name, function: Gilles Catala,
Manager, Wireless Test & Certification Center

9260NGW-EU-RED-DoC.pdf

TEC_RT_60128278_0001_9260NGW.pdf
“Intel Wireless-AC 9260 Regulatory Documentation” “Intel Wireless-AC 9260NGW Declaration of Conformity” “Intel Wireless-AC 9260NGW Type Examination Certificate”
Please be aware that the support site URL may be changed from time to time. If you are not able to find the relevant information, please contact our support.