Embed Size (px)
Citation preview
www.prana.org.ua
Remote control manual
11:59
On/Off “Mini-warm-up”
Operating modes switching
“Night” mode
On/Off
“Winter” mode
Sleep timer
“Fan” mode
Adjustment of brightness indication
2
Adjustment of brightness indication
Turn “Mini-heating” Off Turn “Mini-heating” On
Operating modesswitching
“Night” mode
Turn Off
zz z
“Winter” mode
Sleep timer
“Fan” mode
3
1.First start
11:59
Check if power is connected to the vent system. NO INDICATION – electric current doesn`t flow. “-“ electric current flows, but system is off.
Start the mobile application. Bluetooth service will turn On auto-matically and application will be connected to the vent system. Sys-tem is ready for use.
2.Adjustment of brightness indicationTo provide customer with the most comfortable usage experi-
ence during the dark, our system has 6 indication brightness levels.Indication brightness can be adjusted by * button on the re-
mote controller or * button in the mobile application.
4
11:59
“L” (LOW) displays on indication panel – “Night” mode is On. Min-imal vent system operating mode.
For “Winter” mode tap * button in the application or press on your remote controller.
Volume of air exchange at “Night” mode м3/hour:
150 | 200G | 200C | Model 25 | 25 | 40 | Supply 22 | 22 | 36 | Exhaust
Recuperation efficiency %: 91 | 92 | 93
Noise level at 3m. distance dB: 5 | 4 | 4
3.“Night” more
5
11:59
/105
Numbers from 2 to 9 on the indication panel – system works in appropriate operating mode.
Setting up system air exchange performance from 20% to 90%. Each mode increases/degreases performance by 8%. Can be man-aged by buttons +/- via application or +/- on remote controller.
* - Parameters that are shown in the graphs could vary by +-4% from real parameters depending on weather conditions, atmospheric pressure, relative humidity of air, etc…
4.Operating modes 2-9
6
260
240
220
200
180
160
140
120
100
80
60
40
20
0L 2 3 4 5 6 7 8 9 H
40
35
30
25
20
15
10
5
0L 2 3 4 5 6 7 8 9 H
100
90
80
70
60
50L 2 3 4 5 6 7 8 9 H
Volume of air exchange м3/hour
Noise level, dB
Recuperation efficiency %
Prana-150
Prana-200G
Prana-200C
Prana-150
Prana-200G
Prana-200C
Prana-150
Prana-200G
Prana-200C
76
11:59
/1010“H” (HIGH) on the indication panel – system works in “Fan” mode.
Maximal vent system operating mode.
For “Fan” mode tap * button in the application or press on your remote controller.
Volume of air exchange in “Fan” mode м3/hour:
150 | 200G | 200C | Model 115 | 135 | 235 | Supply 105 | 125 | 220 | Exhaust
Recuperation efficiency %: 67 | 70 | 62
Noise level at 3m. distance dB: 30 | 29 | 34
5.“Fan” Mode
8
6.“Sleep timer” function
11:59
/101
00:10:00
“Selected operation mode“ on the indication panel, «S» flashes each 5 seconds.
“Sleep timer” function turns on by tapping button in the application or pressing button on the remote controller.
To manage timer duration use +/- buttons in application or +/- on the remote controller. After the timer expires, system will turn off au-tomatically. There are 9 default timer configurations. When choosing one of the configuration, numbers from 1 to 9 will appear on indica-tion panel.
Timer configurations:1 – 10 minutes2 – 20 minutes3 – 30 minutes4 – 1 hour5 – 1 hour 30 minutes6 – 2 hours7 – 3 hours8 – 5 hours9 – 9 hours
5SEC
8 9
zz z
“Selected operation mode” flashes each second on the indica-tion panel.
For extra comfort of the organizations of ventilation of living quar-ters, the Prana household and semi-industrial systems are equipped with a “Mini-warm-up” function of the supply air. Function turns On by tapping button in the application or pressing button on the remote controller.
When “mini-warm-up” is On, temperature of the supply air addi-tionally warms up by 3 – 5°C.
ATTENTION! In the case of air temperature outside lower than 0°C in the rooms with the humidity of 55% or higher to avoid icing of the condensate discharge paths vent system “Mini-warm-up” function must be turned On.
7.“Mini-warm-up” function
11:59
/1010
1SEC 1SEC
10
11:59
/103
00:00:58
Near the selected operating mode on the indication panel each second flashes “.” – “Winter” function is On, heating element works.
“.” displays on the indication panel near the selected operating mode – “Winter” mode is on, heating element works in passive mode and turns on automatically when needed.
“Winter” function intended to prevent icing of the condensate discharge paths in the cold season or to defrost paths in the case of already formed icing.
ATTENTION! To prevent icing and ensure correct work of the sys-tem in the case of sub-zero temperature outside the room – system must work with “Winter” mode turned On.
Turn “Winter” function on by tapping * button in application or pressing * button on your remote controller and choose needed operating mode of the vent system.
After “Winter” function timer expired system will start working in selected operating mode.
ATTENTION! Vent system engines will start only after “Winter” func-tion timer expired.
8.“Winter” function
1SEC 1SEC
11
tel./fax: +38 032 232 53 39 e-mail: [email protected]
Ukraine, 79021, Lviv,Kulparkivska st. 93А
www.prana.org.ua
10/05/18
