Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
Remplacer un pad LED sur une Maxspect R420r
Auswechseln eines LED-Pad bei der Maxspect R420r
Replacing an LED pad on the Maxspect R420r
Pour ouvrir la lampe, enlevez le cache avec vos ongles ou un tournevis plat Um die Leuchte zu öffnen, entfernen Sie die Abdeckung mit den Fingernägeln oder einem Schlitzschraubenzieher. To open the light, remove the cover with your fingernails or a flathead screwdriver.
Puis enlever le pad optique
Entfernen Sie dann das Pad mit den Optiken
Then remove the optical pad
A présent vous avez accès au pad LED
Jetzt haben Sie Zugang zu dem LED Pad LED
Now you have access to the LED pad
Dévissez les 4 vis et désolidarisez le pad LED du châssis
Öffnen Sie die 4 Schrauben und lösen Sie das LED pad von dem Gehäuse
Unscrew the 4 screws and unfasten the LED pad from the chassis
Otez le pad LED à changer en faisant attention aux câbles
Entfernen Sie die LED-Pad achten Sie aber auf die Kabeln
Remove the LED pad to change by paying attention to the wires
Prenez votre nouveau pad LED ainsi que le pad de conductivité de chaleur
Nehmen Sie das neue LED-Pad und das Wärmeleiter Pad
Take the new LED-pad and the heat conductor pad
Enlevez le pad de conductivité de son support et collez-le soigneusement sur le pad LED
Entfernen Sie das Leitfähigkeit Pad und kleben Sie es sorgfältig auf das LED-Pad
Remove the conductivity pad and apply it carefully on the LED pad
Ensuite enlevez le film de protection bleu du pad de conductivité
Entfernen Sie die blaue Schutzfolie von dem Leitfähigkeit Pad
Then remove the blue protective film from the conductivity pad
Mettez le pad LED de la lampe de côté afin de faire de la place pour le nouveau pad LED
Legen Sie das LED-Pad von der Leuchte beiseite um Platz für das neue LED-Pad zu
machen
Put the LED pad from the light aside to make space for the new LED pad
Posez le nouveau pad LED à la place de l’ancien en faisant bien attention au positionnement des contacts A+, B+ et A-, B-
Legen Sie das neue LED-Pad anstelle des anderen und achten Sie auf die Positionierung
der A +, B + und A-, B- Kontakte
Put the new LED pad instead of the former being careful of the positioning of the A +, B + and A-, B-contacts
Mettez l’ancien pad LED sur le nouveau puis dévissez respectivement les câbles du plot A+ et B+ l’un après l’autre et revissez les respectivement l’un après l’autre sur le plot A+ et B+
du nouveau pad LED
Legen Sie das alte LED Pad auf das Neue lösen Sie dann entsprechend die Kabeln von den Klemmen A+ und B+, einen nach dem anderen und schrauben Sie dann jeweils die Kabeln
einem nach dem anderen an die Klemmen A+ und B+ von dem neue LED-Pad
Put the old to the new LED pad and unscrew respectively the wires from terminals A + and B+, one after the other and screw them respectively one after the other on the terminal A +
and B+ of the new LED pad
Puis faites de même pour A- et B-, un câble après l’autre afin de ne pas les intervertir
Für A-und B- tun Sie dann das Gleiche, ein Kabel nach dem anderen, damit sie nicht verwechselt werden
Then do the same for A-and B-, cable after another so you do not mistake
Puis positionnez bien votre pad LED par rapport aux optiques du pad optique
Legen Sie dann das LED Pad so dass es genau, mit den Optik, des Optik-Pad einstimmt
Then, set out your LED pad relative to the optic of the optical pad
Revissez les vis de fixation du pad LED en les serrant correctement
Befestigen Sie die Schrauben des LED-Pad und ziehen Sie diese gut an.
Tighten the screws holding the LED pad by squeezing correctly
A présent vous pouvez à nouveau refermer la lampe avec le couvercle
Jetzt können Sie wieder die Leuchte mit dem Deckel schließen
Now, you can close again the light with the cover
__________________________________________________________________________
Comment changer le pad LED central
Auswechseln des Zentrale LED Pad
How to change the central LED pad
Pour changer le pad LED central, il faut dévisser un des 2 supports ventilateurs puis
procéder de la même manière qu’auparavant.
Um das zentrale LED-Pad auszuwechseln, lösen Sie eine der beiden Ventilatoren Halter und
dann in der gleichen Weise verfahren wie zuvor.
To change the central LED pad, unscrew one of the 2 fans holders and then proceed in the
same manner as before.