Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
2/8/2019 TSB • Fuel System • [ENG139] VCMA Diagnosis - MIL On With DTC P200A (ENG 139 Rev 1) • 2011 Kia Sorento • MotoLogic
https://www.motologic.com/car/2011_sorento_xm/article/403e51-4b8ca644e4be87e061dac2ce653d89a2f702750f0?returnPath=%2Fcar%2F2011_sor… 1/7
Report a problem with this article
2011 Kia Sorento
GROUP MODELEngine 2011-2013MY
Sorento (XMa)NUMBER DATE139 (REV 1, 10/31/2013) September 2013
TEC HNIC AL SERVIC E BULLETINSUBJECT: VC MA DIAG NO SIS - MIL O N WITH DTC P200A
Ø NOTICEThis bulletin has been revised to include additional information. New/revisedsections of this bulletin are indicated by a black bar in the margin area.
This bulletin provides information for some 2011-2013MY Sorento (XMa) vehicles, equippedwith a 3.5L MPI engine, which may exhibit a Malfunction Indicator Lamp (MIL) with DTC P200A,after engine startup. DTC P200A may be caused by an inoperative VCM actuator, or by aninoperative valve linkage inside the intake manifold assembly. If the VCMA or the valve linkageis inoperative, the ECM may not be able to correctly control the intake path of air into theengine. Follow the procedures outlined in this bulletin to diagnose and correct the concern.
DTC P200A Intake Manifold Runner Performance
Variable Charge Motion Actuator(VCMA)
File Under: <Engine>
x x xCirculate To: ¨ General Manager ¨ Service Manager ¨ Parts Manager
x x x¨ Service Advisor(s) ¨ Technician(s) ¨ Body Shop Manager ¨ Fleet Repair
2/8/2019 TSB • Fuel System • [ENG139] VCMA Diagnosis - MIL On With DTC P200A (ENG 139 Rev 1) • 2011 Kia Sorento • MotoLogic
https://www.motologic.com/car/2011_sorento_xm/article/403e51-4b8ca644e4be87e061dac2ce653d89a2f702750f0?returnPath=%2Fcar%2F2011_sor… 2/7
Page 2 of 7
SUBJECT: VC MA DIAG NO SIS - MIL O N WITH DTC P200A
SERVICE PROCEDURE:
1. Open the hood and remove the engine cover.
2. Turn the ignition “ON” and check for the presence of the Malfunction Indicator Lamp (MIL)illuminated on the dash.
3. Connect the power supply cable to the GDS tool.
4. Connect the USB cable between the VCI and the GDS tool.
5. Connect the Main 16-pin DLC cable (GHDM – 241000) to the VCI.
6. Connect the Main 16-pin DLC cable(GHDM – 241000) to the OBD-IIconnector, located under the driver'sside of the instrument panel.
7. With the ignition key ON, turn “ON” the VCI and GDS tool. Access the GDS vehicleidentification number (VIN) screen and configure the vehicle using the VIN AUTODETECT Function.
8. Select ENGINE system and clickOK.
TSB: ENG 139 (REV 1) Sorento (XMa) September 2013
2/8/2019 TSB • Fuel System • [ENG139] VCMA Diagnosis - MIL On With DTC P200A (ENG 139 Rev 1) • 2011 Kia Sorento • MotoLogic
https://www.motologic.com/car/2011_sorento_xm/article/403e51-4b8ca644e4be87e061dac2ce653d89a2f702750f0?returnPath=%2Fcar%2F2011_sor… 3/7
Page 3 of 7SUBJECT: VC MA DIAG NO SIS - MIL O N WITH DTC P200A
9. Click on Current Data.
10. Click on DTC Analysis and checkfor the presence of DTC P200A.
11. Select Current Data > ActuationTest > VCM Motor.
· Use the START and STOPbuttons to activate the VCMA.
· Visually check VCMA activationunder the hood.
12. If the VCMA activates, no further action on the VCMA is required. Proceed to step 14.
13. If the VCMA does not activate, replace it by referring to the applicable Service Manual onKGIS. Proceed to step 14 for additional testing of the valve linkage.
TSB: ENG 139 (REV 1) Sorento (XMa) September 2013
2/8/2019 TSB • Fuel System • [ENG139] VCMA Diagnosis - MIL On With DTC P200A (ENG 139 Rev 1) • 2011 Kia Sorento • MotoLogic
https://www.motologic.com/car/2011_sorento_xm/article/403e51-4b8ca644e4be87e061dac2ce653d89a2f702750f0?returnPath=%2Fcar%2F2011_sor… 4/7
Page 4 of 7
SUBJECT: VC MA DIAG NO SIS - MIL O N WITH DTC P200A
14. After successfully testing the actuation of the VCMA, or replacing the VCMA, select DataAnalysis > Current Data > Actuation Test to actuate the valve linkage.
15. Check the box for VPS Scaled Stopped100%Position and click on the Start and
Stop buttons.
Ø NOTICEDisplayed values for the valvelinkage test will vary from vehicleto vehicle.
16. Perform the valve linkage actuation Activetest a total of three (3) times. 19.6%Record and compare the actualvalues displayed to thespecification values shown in thetable below.
Specification Values
Stopped Active
90% (±10%) 25% (±10%)
17. If the values are within specification, no further action is required. If there is no change inthe values, replace the lower intake manifold assembly by referring to the applicableService Manual on KGIS.
18. Reinstall all other removed components.
TSB: ENG 139 (REV 1) Sorento (XMa) September 2013
2/8/2019 TSB • Fuel System • [ENG139] VCMA Diagnosis - MIL On With DTC P200A (ENG 139 Rev 1) • 2011 Kia Sorento • MotoLogic
https://www.motologic.com/car/2011_sorento_xm/article/403e51-4b8ca644e4be87e061dac2ce653d89a2f702750f0?returnPath=%2Fcar%2F2011_sor… 5/7
Page 5 of 7SUBJECT: VC MA DIAG NO SIS - MIL O N WITH DTC P200A
19. Perform a VCMA relearn procedure as outlined below, otherwise, DTC P200A may recur.
· Turn OFF the ignition switch· Connect GDS to the Data Link Connector (DLC)· Turn the ignition switch ON· Select the “Vehicle”, “Model year”, “Engine” and “System”· Select the “Vehicle S/W Management”· Select “Inspection/Test”· Select “Inspection/Test”
· Perform the VCM learning procedure according to the message on the GDS screen.
TSB: ENG 139 (REV 1) Sorento (XMa) September 2013
2/8/2019 TSB • Fuel System • [ENG139] VCMA Diagnosis - MIL On With DTC P200A (ENG 139 Rev 1) • 2011 Kia Sorento • MotoLogic
https://www.motologic.com/car/2011_sorento_xm/article/403e51-4b8ca644e4be87e061dac2ce653d89a2f702750f0?returnPath=%2Fcar%2F2011_sor… 6/7
Page 6 of 7
SUBJECT: VC MA DIAG NO SIS - MIL O N WITH DTC P200A
· Follow the on-screen instructions to finalize the test.
20. Clear DTC(s) if present.
21. Test drive the vehicle for two drive cycles in order to verify normal operation and norecurrence of MIL on.
TSB: ENG 139 (REV 1) Sorento (XMa) September 2013
2/8/2019 TSB • Fuel System • [ENG139] VCMA Diagnosis - MIL On With DTC P200A (ENG 139 Rev 1) • 2011 Kia Sorento • MotoLogic
https://www.motologic.com/car/2011_sorento_xm/article/403e51-4b8ca644e4be87e061dac2ce653d89a2f702750f0?returnPath=%2Fcar%2F2011_sor… 7/7
Page 7 of 7SUBJECT: VC MA DIAG NO SIS - MIL O N WITH DTC P200A
AFFEC TED VEHIC LE PRO DUC TIO N RANG E:
Model Production Date Range
Sorento (XMa) 2011-2013MY
PART INFO RMATIO N:
Part Name Part Number Figure
VCMA 28320 3C000Assembly
Intake Manifold Assembly 28310 3CAA0
WARRANTY INFO RMATIO N:
Claim Causal N C Repair Labor Op Op ReplacementQty. Qty.Type P/N Code Code Description Code Time P/N
(TSB ENG 139)28320 0.3W 0 N69 C06 DTC Inspection 28320F04 N/A 03C000 M/Hfor Stored Codes
(TSB ENG 139)28320 VCM 0.3W 1 N69 C06 28320F05 N/A 03C000 Replacement and M/H
DTC Inspect
(TSB ENG 139)28320 Intake Manifold 0.8W 1 N69 C06 28320F06 N/A 03CAA0 Replacement and M/H
DTC Inspect
(TSB ENG 139)VCM and Intake 0.828310W 1 N69 C06 Manifold 28320F07 M/H 28320 3C000 13CAA0 Replacement, withDTC Inspection*
* Scan tool screen captures must be printed and attached to the RO, failure to attach printed screen capture mayresult in chargeback.
Note: Only one (1) labor operation maybe submitted with claim, all labor operations include scan tool diagnostictime.
TSB: ENG 139 (REV 1) Sorento (XMa) September 2013