Upload
others
View
15
Download
0
Embed Size (px)
Citation preview
Research ArticleFacile Synthesis and Characterization of N-DopedTiO2 Photocatalyst and Its Visible-Light Activity forPhoto-Oxidation of Ethylene
Yu-Hao Lin,1 Chih-Huang Weng,2 Arun Lal Srivastav,3
Yao-Tung Lin,3 and Jing-Hua Tzeng3
1Centre for Environmental Restoration and Disaster Reduction, National Chung Hsing University, 250 Kuo Kuang Road,Taichung 40227, Taiwan2Department of Civil and Ecological Engineering, I-Shou University, Kaohsiung City 84008, Taiwan3Department of Soil and Environmental Sciences, National Chung Hsing University, 250 Kuo Kuang Road, Taichung 40227, Taiwan
Correspondence should be addressed to Yao-Tung Lin; [email protected]
Received 25 August 2014; Accepted 10 December 2014
Academic Editor: Yuekun Lai
Copyright © 2015 Yu-Hao Lin et al. This is an open access article distributed under the Creative Commons Attribution License,which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
A facile wet chemical method was adopted for preparing highly photoactive nitrogen doped TiO2(N-TiO
2) powders with visible
responsive capability, which could be achieved by the hydrolysis of titanium isopropoxide (TTIP) in the ammonium hydroxideprecursor solution in various concentrations and then calcined at different temperatures. The N-TiO
2powders were characterized,
and the photocatalytic activity was evaluated for the photocatalytic oxidation of ethylene gas under visible light irradiationto optimize the synthesizing conditions of N-TiO
2catalyst. The N-TiO
2photocatalytic powders were calcined in a range of
temperatures from 300 to 600∘C and obviously found to have greater photocatalytic activities than commercial TiO2P25. The
strong absorption in the visible light region could be ascribed to good crystallization and adapted sinter temperature of as preparedsample. XPS test demonstrated that the N was doped into TiO
2lattice and made an interstitial formation (Ti-O-N), and N doping
also retarded the phase transformation from anatase to rutile as well. The N-TiO2catalyst prepared with 150mL ammonium
hydroxide added and calcined at 500∘C showed the best photocatalytic activity. The experimental results also proved the enhancedphotoactivity of N-TiO
2material depends on the synthesizing conditions.
1. Introduction
Recently, the nanomaterial, such as nanoiron, titanium diox-ide photocatalysts (TiO
2), has applied for groundwater reme-
diation, degradation of hazardous materials, and environ-ment cleanup [1–3]. However, the wide band gap of TiO
2for
anatase crystal structure requires UV light and occupied lessthan 10% energy in solar spectrum for the excitation ofelectron-hole pairs [4], which restricts the application of TiO
2
because of low photo quantum efficiency.Various metals such as Ag have been doped into the
TiO2lattice to shift its absorption from UV to visible light,
and doping improved their photocatalytic activities [5].In addition, literatures also fabricated the nanotube arrayor hybrid structures of element-doped-TiO
2to enhance
the photocatalytic activity [6, 7]. However, none of themgave satisfactory results due to their thermally instabilityand increased carrier trapping [8]. Relatively, the dopingof anion on TiO
2such as nitrogen and carbon element
doped and codoped has considerable effect on increasing itsphotocatalytic activity [9–14], in which, the nitrogen seems tobe the most effective dopant due to its similar size to oxygenand metastable defect complex, as well as small ionizationenergy [15], and N-doped TiO
2(N-TiO
2) has an advantage
on photocatalytic activity [16, 17]. Hence, literatures focusedon discussing the structure of N-TiO
2using the X-ray photo-
electron spectroscopy (XPS), electron spin resonance, or X-ray absorption near edge structure. Some reports claim thatthe band gap of the N-TiO
2is reduced due to a rigid valence
band shift upon doping [18], others attributed the observed
Hindawi Publishing CorporationJournal of NanomaterialsVolume 2015, Article ID 807394, 10 pageshttp://dx.doi.org/10.1155/2015/807394
2 Journal of Nanomaterials
absorption of visible light by N-TiO2to the excitation of
electrons from localized N-impurity states in the band-gap[8, 19]. In general, the change in banding structure of N-TiO
2
was attributed to the N interstitial doping, N substitution,and O vacancy [20–22]. However, till now the structureof N-TiO
2is still under debate. The preparatory methods
and conditions such as nitrogen precursor and sinteringtemperature may considerably affect the nitrogen state in thedoped TiO
2[19, 23]. But, only few systematic discussions
have been found regarding the dominated factor ratio of Nto Ti and calcination temperature for the activity of N-TiO
2,
simultaneously.In other words, it is necessary to understand the chemical
fine-tuning and further optimization of the visible-lightphotocatalytic activity of N-TiO
2. The goal of this study
is (1) to develop a simple method for the synthesis of N-TiO2nanomaterials using facie method at various conditions
of nitrogen precursor amounts and composite calcinationtemperatures, (2) characterization of N-TiO
2composite
materials, (3) carried out the photocatalytic activity of asprepared N-TiO
2under visible light.
Ethylene is a plant hormone that controls many plantresponses, and its higher concentration can affect the foodand horticultural product industry [24], safe handling, andthe parent compound of important environmental contam-inants, and the photocatalytic activity for the degradationwas quite different from that of volatile chlorinated organiccompounds such as trichloroethylene [25]. Therefore, batchexperiments were conducted for the removal of ethylene toevaluate the N-TiO
2photoactivity under visible light irra-
diation and have also been compared with that of commer-cial photocatalysts Degussa P25. Materials characterizationshave been performed through specific surface area analy-sis, X-ray diffraction (XRD), scanning electron microscope(SEM), electron Spectroscopy for Chemical Analysis (ESCA),and diffuse reflectance ultraviolet-visible absorption spectra(DRS UV-vis).
2. Materials and Methods
2.1. Chemicals and Synthesis of N-TiO2Composite. All the
chemicals were used as procured without further purifica-tion. Commercial photocatalyst P25 was purchased fromDegussa. Ammonium hydroxide (NH
4OH, 33wt%), tita-
nium tetraisopropoxide (TTIP), and absolute ethanol (99.8%)were procured from J. T. Baker. Synthesis procedure of N-TiO2composite was modified as reported in literatures [16,
26], and ammonium hydroxide was chosen as a nitrogenprecursor. Different amounts of ammonium hydroxide (0–200mL) and DI water (200–0mL) were mixed with absoluteethanol (200mL) in a flask, and then a 400mL ammoniasolution (concentration 0–8.4M) was obtained. The 10mlTTIP was added dropwise into the ammonia solution andstirred vigorously for 4 h at 4∘C in a water bath. After thatthe hydrolysis and condensation reactionwas kept on stirringfor 24 h at room temperature, and then the sol-gel solutionsstood to 24 h in aged conditions.The ensuing colloidwas thencentrifuged and washed thoroughly with distilled water toremove the residual reactants. The final precipitate was dried
at 105∘C overnight in air and calcined at various temperaturesfor 5 h to obtain the final N-TiO
2composite. The synthesized
N-TiO2composites were labeled as N
𝑥T𝑦, where 𝑥 and 𝑦
represent the amount (mL) of ammonium hydroxide addedduring the synthesis procedure and calcinations temperature(unit is 100∘Cper scale), respectively. For example, theN
150T5
catalyst indicates the addition of 150mL ammonium hydrox-ide during the sol-gel procedure of amorphous N-TiO
2
catalyst, followed by its calcination at 500∘C temperature.Pure TiO
2catalyst was named as N
00Ty (𝑥means “zero”), and
there was not any addition of ammonium hydroxide duringsynthesis procedure, such that N
0T3refers to the pure TiO
2
catalyst which was calcined at 300∘C temperature.
2.2. Characterization of Composite. The composite was char-acterized by means of XRD, DRS UV-vis, XPS, and specificsurface area. XPS were recorded on an ESCA spectrometer(ULVAC-PHI, PHI 5000, Japan) operated at 150W and wereused to investigate the surface properties in the valence bandof the composite. The shift of the binding energy due torelative surface charging was corrected using the C 1s asan internal standard. The optical absorption responses ofcomposite were obtained from the pressed disk compositeusing UV-vis (Hitachi, U-3900H, Japan) equipped with anintegrated sphere, and BaSO
4was used as a reference. Specific
surface areas of samples were obtained by the Brunauer-Emmett-Teller (BET) method using nitrogen adsorptionapparatus (Micromeritics ASAP 2020, USA). Samples weredegassed at 150∘C for 2 h prior to the measurements. Thecrystal phases of the composites were analyzed by XRD(PANalytical X’Pert Pro MRD, USA) with Cu-Ka radiationand diffraction angle range of 2𝜃 which is 20∘ to 80∘. Thecrystal size was determined according to Scherrer’s equationand fraction of anatase phase in the mixture was calculatedby formula proposed by Spurr [27].
2.3. Photocatalytic Activity of N-TiO2. During this study,
removal ethylene was studied in batch experiment modesto evaluate the photocatalytic activity of N-TiO
2samples
as well as commercial photocatalyst P25. All the powders(0.5 g) were coated onto the flask bottle (catalyst filmwas keptat 1mg/cm2) and caped with sleeve stoppers. The constantethylene was injected into the flask to get initial ethyleneconcentration (about 140 or 85 ppmv in different test); a150 𝜇L aliquot regularly was withdrawn and injected intogas chromatograph equipment equipped with flame ioniza-tion detector (PerkinElmer Clarus 500, USA) to analyzethe ethylene concentration. The visible illumination wasprovided by six three-colored fluorescent lamps (March T5-8W/865), located above the flasks equipped with a filter tocut the UV light region. The visible irradiance 610 nm wasdetermined by detector (international light SED005) andabout 0.62mW/cm2 at the bottom of flask.
3. Result and Discussions
3.1. BET, XRD, and SEMAnalysis. Thecharacteristics of com-posites including surface area, anatase phases, and crystallitesize are summarized in Table 1 and Figure 1, in which, the
Journal of Nanomaterials 3
Table1:Ch
aracteris
ticsa
ndrateconstant
ofN-dop
edTiO
2prepared
atvario
usN/Tiratio
andcalcinations
temperature.
Sample
BET
XRD
SEM
UV-vis
Activ
itySpecifics
urface
area
Pore
size
Pore
volume
Adsorptio
ntype
aPh
asec
ontent
bCr
ystalline
sizec
Size
Band
gapd
Rateconstant
m2 /g
nmcm
3 /g
cm3 /g
A/R/B
(%)
nmnm
Eg1(eV
)Eg
2(eV)
×10−2h−1
N00T 2
258.9
3.4
0.28
IV78/00/22
14—
——
—N
00T 3
144.7
4.8
0.24
IV79/00/22
17—
2.03
2.99
—N
00T 4
70.1
5.3
0.25
IV82/00/18
24—
—3.04
—N
00T 5
65.8
6.2
0.17
IV86/00/14
5522
—3.05
0.63∗
N00T 6
19.5
9.60.08
IV92/08/00
113
——
2.91
—N
00T 7
0.5
18.3
0.01
V28/72/00
138
——
2.87
—N
00T 8
0.2
25.9
0.00
V06/94/00
155
——
——
N50T 3
144.8
4.8
0.24
IV100/00/0
31—
2.51
3.18
1.72#
N100T
3231.7
3.9
0.28
IV100/00/0
28—
2.51
3.06
1.09#
N150T
3186.1
4.0
0.27
IV100/00/0
27—
2.46
3.12
1.93#
0.87∗
N200T
3260.4
3.5
0.27
IV100/00/0
25—
2.52
3.05
1.29∗
N150T
2319.9
3.2
0.22
IV—
—e
——
——
N150T
461.0
6.6
0.16
IV100/00/0
36—
2.38
3.10
1.50∗
N150T
545.3
6.9
0.13
IV100/00/0
3721.3
2.39
3.13
1.76∗
N150T
634.2
9.30.11
IV100/00/0
62—
—3.01
1.54∗
N150T
70.8
29.5
0.03
V78/22/00
108
——
2.92
0.01∗
N150T
81.6
39.7
0.04
V58/42/00
113
——
2.92
0.00∗
P25
51.2
18.7
0.25
IV82/18
/00
62—
3.04
0.47∗
a Adsorptioniso
therm
type
andhyste
resis
loop
wereb
ased
ontheIUPA
Cmanual;b A
,R,and
Bdeno
teanatase,rutile,andbroo
kite,respectively
;cfro
mXR
DdatausingS
chererform
ula;
d the
band
gapisdeterm
ined
bytheplot
of(𝛼ℎ])
1/2versus
photon
energy,assho
wnin
Figure
4;e noob
viou
scharacteristicpatte
rnof
crystaltocalculatethesiz
e;∗experim
entalcon
ditio
ns:reactiontemp.=20∘C,
R.H.=
63%,[C 2
H4]initial=
140p
pmv,light
intensity
=0.62
mW/cm
2 ;# exp
erim
entalcon
ditio
ns:reactiontemp.=20∘C,
R.H.=
53%,[C 2
H4]initial=85
ppmv,light
intensity
=0.62
mW/cm
2 .
4 Journal of Nanomaterials
0
50
100
150
200
250
300
350
0
10
20
30
40
50
0 50 100 150 200
Crys
talli
ne si
ze (n
m)
Added N source amount (mL)
Spec
ific s
urfa
ce ar
ea (m
2/g
)
Calcination temp.: 300∘C
(a)
0
50
100
150
200
250
300
350
0
20
40
60
80
100
120
200 300 400 500 600 700 800
Crys
talli
ne si
ze (n
m)
Spec
ific s
urfa
ce ar
ea (m
2/g
)
Calcination temperature (∘C)
Added 150mL N source
(b)
Figure 1: The specific surface area of N-TiO2samples as a function of (a) the various ammonium hydroxide amounts added and (b) calcina-
tions temperature.
crystallite size and phase content of sample is calculatedusing the Scherrer equation from XRD peak position andfull width half maximum [27]. Comparing Figure 1(a) withFigure 1(b), the unobvious change in the BET surface area andcrystalline size of samples were observed after the additionof N precursor amounts. However, the clear changes in com-posites at different calcination temperatures depicted thatthe dominant factor for surface area and crystalline size ofcatalysts are calcination temperature, not the addition of Namounts.The pore size and pore volume of composite relativeto surface area decreased with the increase of the calcinationtemperature, and this result is attributed to the pores col-lapsed and bigger crystallites aggregation of catalyst [28].
The XRD patterns of N-TiO2samples in different condi-
tions are shown in Figure 2. The diffraction peaks markedwith letters “A” and “R” on the figure corresponds to theanatase and rutile phase, respectively. In Figure 2(a), themajor peak of 2 theta at about 25.5∘ corresponding to crystalplane (101) of anatase, which became thinner and the rel-ative intensity was increased with calcination temperature.Such stronger crystalline flair of catalyst would enhance itsphotoactivity. The XRD patterns of N-TiO
2synthesized with
different nitrogen precursors presented in Figure 2(b) havealso shown the similar results. It was also depicted that thenitrogen precursor amount did not significantly affect the N-TiO2crystal phase and crystal size.
The N-TiO2catalyst (N
150T3) shows great effect on the
photoactivity and also prevents the conversion of N-dopedamount into nitrogen gas during calcination process. Thissample synthesized with 150mL N precursor was tested toinvestigate the effects of calcination temperature and theresult is presented in Figure 2(c).
In Figures 2(a) and 2(c), the anatase phase on pure andN-doped TiO
2sample started to appear at 200∘C and 300∘C
calcination temperatures, respectively.Thephase transforma-tion from anatase to rutile was observed after the 600∘C and700∘C calcination temperatures. This result can be impliedthat the nitrogen-doped catalyst retarded the phase transfor-mation [10]. Such higher thermal stability could elevate the
anatase crystallinity and promoted the photo-induced chargeseparation and transportation [29]. The interesting brookitephase was only observed in pure TiO
2(see Figure 2(a)) and
disappeared as the beginning of rutile phase, and furtherthe inhibited form of the brookite phase in the N-TiO
2was
implied (Figure 2(c)), since the addition of nitrogen in N-TiO2catalyst. Figures 2(b) and 2(c) showed that theN-doped
TiO2samples had typical peaks of polycrystalline anatase
structure and rutile without any detectable dopant relatedpeaks, such as TiN, which was possibly due to the movementof dopant ions either into interstitial positions or substitu-tional sites of the TiO
2structure or ion concentration, was
detected to be too low [30].Themorphology and particle size of the N-TiO
2(N150
T5)
and pure TiO2(N00T5) samples can be obtained from an
examination of the SEM image (Figure 3). Single particle inagglomerates in both of them exhibited uniform sphericalshape; the size was in range from 20 to 25 nm and a narrowsize distribution appeared. Both of these sizes were slightlysmaller than the crystallite sizes determined from the XRDin Figure 1(b).The results of similar size andmorphology alsoindicated that the N precursor did not have significant effecton the particle size and shape of TiO
2catalyst.
3.2. DRS UV-Vis and ESCA. In this study, the N-TiO2pow-
ders sintered below 600∘C, all exhibited a pale yellow colorwhich suggests its ability to absorb light in the visible region[31]. However, Qiu and Burda infer that the obtained UV-visspectra that localized defect states may also play a role in pro-viding visible light activity [32]. Optical absorption spectra ofthe N-TiO
2and Degussa P25 samples are shown in Figure 4,
and the absorption at wavelengths shorter than 400 nm canbe assigned to the intrinsic band gap absorption of TiO
2.
A significant shift of the absorption edge to a lower energyin the visible-light region was observed for N-doped TiO
2.
This result indicates that band-gapnarrowing has successfullybeen achieved by the doping of N into the TiO
2lattice,
presumably due to the modification of the band structure
Journal of Nanomaterials 5
20 30 40 50 60 70 80
Inte
nsity
(a.u
.)A
(101)A
(004)A
(200)A
(105) A(211)
A(204)
R(110)
R(101)
R(111)R
(210)
R(211)R
(220)
B(211)
200
300
400
500
600
700
800
TiO2
temp. (∘C)Calcination
2𝜃 (deg)
(a)
20 30 40 50 60 70 80
Inte
nsity
(a.u
.)
A(101)
A(004)
A(200)
A(105)
A(211)
A(204)
B(211)
0
50
100
150
200
N source amount added(mL)
N-TiO2
2𝜃 (deg)
Calcination temp. 300∘C
(b)
20 30 40 50 60 70 80
Inte
nsity
(a.u
.)
A(101)
R(110)
A(004)
R(101)
R(111)
R(210)
A(200)
A(105)
R(211)
A(211)
A(204)
R(220)
200
300
400
500
600
700
800
N-TiO2
temp. (∘C)
Added 150mL N
Calcination
2𝜃 (deg)
source
(c)
Figure 2: XRD pattern of (a) pure TiO2calcined at different temperature, (b) N-TiO
2samples synthesized in different loading of ammonium
hydroxide amounts, and (c) N-TiO2samples calcined at different temperature.
(a) (b)
Figure 3: SEM images of (a) pure TiO2and (b) N-TiO
2catalyst.
6 Journal of Nanomaterials
350 400 450 500 550 600
Abso
rban
ce (a
.u.)
Wavelength (nm)
P25
2.0 2.4 2.8 3.2
Band gap (eV)
P25(𝛼h�)1/2
N150T3N200T3N100T3N00T3N50T3
P25
N150T3N200T3N100T3N00T3N50T3
N00T3 Eg1 N00T3 Eg2
Calcinationtemp. 300∘C
(a)
350 400 450 500 550 600
Abso
rban
ce (a
.u.)
P252.0 2.4 2.8 3.2
Band gap (eV)
Wavelength (nm)
150mL nitrogenprecursor addition
(𝛼h�)1/2
N150T3N150T5
N150T6
N150T8 N150T8
N150T7
N150T4
P25
N150T3N150T5
N150T6N150T8
N150T7
N150T4
N150T4 Eg1 N150T4 Eg2
(b)
Figure 4:TheUV-vis adoption pattern ofN-TiO2(a) preparedwith various ammoniumhydroxide amount added and (b) calcined at different
temperature.
[33]. The absorption spectra of the N-doped TiO2samples
show a stronger absorption than undoped TiO2as well as
P25 in the UV-vis light region and a red shift in the bandgap transition except N
50T3sample. The red shift is ascribed
possibly to the oxygen vacancy [34] or the fact that N dopingcan narrow the band gap of the TiO
2[35, 36]. Generally, the
photocatalytic activity is proportional to the photo numbersabsorbed by photocatalyst per second and the efficiency of theband gap transition [28], theNdoping expand thewavelengthresponse range of TiO
2into the visible region and also
increased the number of photo-generated electrons and holesto enhance the photocatalytic performance of N-TiO
2. The
enhanced activity in N-TiO2catalysts also was demonstrated
in Figure 6. Figure 4(a) revealed that the absorbance increaseswith increasing added nitrogen precursor amounts ofN-TiO
2
synthesized condition.Unfortunately, such absorbance is not proportional to
its photoactivity. Further, the UV-vis absorbance spectra ofappropriate samples with different calcined temperature areshown in Figure 4(b). The absorbance of all N-TiO
2samples
in the visible region is higher than that of P25 and may beascribed to the fact that the narrowing of band gap as wellas localized defect resulted from N doping and calcination.Higher than 700∘C calcination, the N-TiO
2powders show
a significant red shift in the band gap transition due to theformation of rutile phase and growth of TiO
2crystallite.
However, interestingly, amorphous N150
T2powders also
showed a greatest red shift. As the calcination temperatureincreased from 300∘C to 600∘C, the intensive absorption ofN150
T4, N150
T3, and N
150T5were observed in the visible
region between 400 and 500 nm, which is the typical absorp-tion feature of nitrogen doped TiO
2[10], whereas it was not
observed on N150
T6sample even if N
150T6appeared better
photoactivity than N150
T3. However, the aforementioned
result could not possibly provide a definite relation betweenabsorbance and photoactivity of as-prepared sample, whichis due to that the absorption features in the visible range
originated from color centers through doping processes orposttreatments rather than by narrowing of the band gap[32, 37]. Literature also reports the intensive absorption ofion doped TiO
2that can be assigned to oxygen vacancies
produced by thermal treatment, which form localizationlevels within the band gap [34].Moreover, the origin of visiblelight absorption originated fromNandOvacancies suggestedthat the N dopants can only affect the absorption below500 nmwavelength, while the O vacancies are responsible forthe induced absorption at wavelengths above 500 nm [38].
ESCA analyses of N 1s and Ti 2p were performed onpure TiO
2, P25, and N-TiO
2catalysts and results are shown
in Figure 5. In Figure 5(a), the binding energy (BE) peakscorresponding to N 1s core-levels for N-TiO
2samples pre-
pared with various amounts of N precursor and calcined at300∘C are observed one major peak at 398–402 eV. However,sometime the binding energy observed at 400 eV is ascribedto N atoms which are incorporated into the TiO
2lattice as
N2molecules [33]. Saha and Tompkins investigated the N 1s
ESCA spectra during the oxidation of TiN and assigned thepeaks as atomic 𝛽-N (396 eV) and molecularly chemisorbed𝛾-N2 (400 eV and 402 eV) [31]. Those different N 1s spectralfeatures are still debated and dependent on different prepara-tion methods and conditions [35]. Further, the Ti 2p
1/2and
Ti 2p3/2
spin-orbital splitting photoelectrons for anatase TiO2
were located at binding energies of about 464.0 and 458.2 eV,respectively, which were assigned to the presence of typicalTi4+. SameTi 2p peaks are located at same binding energy anddistribution (Figure 5(b)), because the N precursor amountwas not a dominating factor in the electronic structure of N-TiO2, although the different activity of N-TiO
2synthesized in
N precursor amount is shown in Figure 6(a).The content of nitrogen were maintained in all the com-
posites smaller than 1% and found decreased with increasingcalcination temperature as shown in Figure 5(c), which maybe due to the replacement of N in the matrix by O and
Journal of Nanomaterials 7
396 398 400 402 404 406
Inte
nsity
(a.u
.)
Binding energy (eV)
N amount added(mL)
100
150
200
50
Calcination temp. 300∘C N 1s
(a)
454 456 458 460 462 464 466 468
Inte
nsity
(a.u
.)
Binding energy (eV)
50
100
N amount added(mL)
150
200
Calcination temp. 300∘C
2p3/2
2p1/2
Ti 2p
(b)
394 396 398 400 402 404 406 408
Inte
nsity
(a.u
.)
Binding energy (eV)
400
500
600
300
Calcination temp.(∘C)
Added 150mL N source N 1s
(c)
455 457 458 460 462 464 465 467
Inte
nsity
(a.u
.)
Binding energy (eV)
P25
300
400
500
600
Calcination temp.2p3/2
2p1/2(∘C) Added 150mL N source
Ti 2p
(d)
Figure 5: The XPS spectra for N-TiO2samples, ((a) and (c)) N 1s and ((b) and (d)) Ti 2p.
0 10 20 30 40 50
050100150200
Time (h)
0.010
0.015
0.020
0.025
0.030
0 50 100 150 200
Added N source amount (mL)
Rate
cons
tant
(h−1)
Calcination temp. 300∘C
R.H. = 53% (20∘C)
0.00
−0.20
−0.40
−0.60
−0.80
−1.00
Added N sourceamount (mL)
ln(C/C
0)
(a)
0.000
0.005
0.010
0.015
0.020
300 400 500 600 700 800N00T5
0 10 20 30 40 50Time (h)
R.H. = 63% (20∘C)
Calcination temperature (∘C)
Rate
cons
tant
(h−1)
Added 150ml N source
0.00
−0.20
−0.40
−0.60
−0.80
−1.00
Calcinationtemp. (∘C)
N00T5300400500
600700800
ln(C/C
0)
(b)
Figure 6: Photocatalytic reaction of N-TiO2samples as a function of (a) the various ammonium hydroxide amount added and (b) the various
calcination temperature.
8 Journal of Nanomaterials
transform to nitride result in lower N concentrations [32].Literature reports that the N dopant was adsorbed NO orbond to oxygen vacancy site in interstitial formation (Ti-O-N), especially at such low N doping concentrations [39].The N 1s peaks also shifted towards higher binding energywith increasing calcination temperature level and appearedas different distribution.However, high sintering temperaturecan also cause the loss of dopants from N-TiO
2catalyst.
Therefore, an appropriate sintering temperature would bemore important to the activity of N-doped TiO
2[32]. At the
same time, in Figure 5(d), the Ti 2p peaks undergone a shifttowards higher binding energy with increasing calcinationtemperatures. This indicates the lowering of electronic den-sity around the central Ti ion by introducing more O next toTi [32]. The above mentioned binding energy shift pointedout that the calcination temperature may be a dominatingfactor in the electronic structure of N-TiO
2, and this is
found consistent with XRD and BET analyses, and thusthe calcination temperature would be key factor for thecharacteristics of N-TiO
2based on synthesized method of
this study.
3.3. Photoactivity of N-TiO2under Visible Light Illumination.
Figure 6 shows the photocatalytic performances for ethyleneremoval over the various N-TiO
2and pure TiO
2in batch
reactions under the visible light irradiation. The rate of pho-tocatalytic oxidation has been described by a pseudo-first-order equation, as presented in (1) [24] and the rate constantvalues are given in Table 1. Consider
ln(𝐶0
𝐶𝑡
) = −𝑘𝑡, (1)
where 𝐶0is the initial concentration of ethylene, 𝐶
𝑡is the
ethylene at time 𝑡, and 𝑘 is the apparent pseudo first photo-catalytic oxidation rate constant. Examination of (1) suggeststhat the apparent pseudo first photocatalytic oxidation rateconstant 𝑘 can be determined experimentally from a plotof ln(𝐶
0/𝐶𝑡) versus time, which has a slope of −𝑘. All the
photocatalytic oxidation rate constants (𝑘) of catalysts aresummarized in Table 1. Figure 6(a) shows the effect of N-TiO2synthesized at different nitrogen precursor with 300∘C
calcination temperature, and the order of the reaction rates(Table 1) was N
150T3, N50T3, N200
T3, N00T3, and N
100T3.
Then, the N-TiO2catalyst was synthesized at 150mL nitrogen
precursor and sintered from 300∘C to 800∘C temperaturesto investigate the effects of sintering temperature on N-TiO
2
photoactivity. In Figure 6(b), the activity of N00T5(Pure TiO
2
sintered at 500∘C temperature) was found better than com-mercial TiO
2P25 under visible light irradiation due to the
transfer of electron and hole between two phases (mix phaseof anatase with few fraction of brookite) which is ascribedto the oxygen vacancy resulted from the calcination at 500∘C[40].
Moreover, the optimizedN150
T5photocatalyst has shown
better ethylene degradation than undoped N00T5and others.
Based on the experimental results, the nitrogen dopingwould improve the photoactivity of undoped TiO
2under
visible light irradiation. Both N150
T7and N
150T8showed less
photoactivity due to the existence of rutile phases and the tiny
BET surface area as shown in Figure 1(b). However, the largestspecific surface area of N
150T3should have theoretically
better photoactivity for the removal of ethylene due to theabundance of active sites. More effectiveness of N
150T5was
also observed for visible region of solar illumination andthere are some other facts that may affect photoactivity ofTiO2under visible illumination such as O vacancy resulted
from calcination and N impurity acted as light sensitization[41, 42]. We have found that not only is the N-TiO
2sample
oxygen-deficient but also it involves a small amount of N-doped. N doping in TiO
2was in interstitial formation (Ti-
O-N) and that function retarded the reoxidation of oxygendeficient TiO
2, which is essentially indispensable for visible
light sensitization [36].
4. Conclusions
N-TiO2nanocatalysts can be developed directly by so-gel
method under the conditions: 150mL ammonium hydroxideprecursor added and 500∘C calcination temperature. Theethylene removal efficiency was dependent on the optimalcontents of nitrogen precursor, surface area, and oxygenvacancy and good crystallization resulted from the adaptedcalcination temperatures [32, 43]. The N-TiO
2powders
showed a stronger absorption in the visible light region from400 to 500 nmwavelength, which was possibly due to narrowband gap by mixing of N 2p states with O 2p states on the topof the valence band or a creation of N-inducedmid-gap level.Other more intensive absorption in the visible light regionlonger than 500 nmwavelength is ascribed to oxygen vacancyresulted from the calcination and N doping. The N-dopingwet-method has an advantage on photocatalytic activity ascompared to metal ion doping (thermally instability). Inaddition, the doped TiO
2enhanced the photoactivity may be
further investigated in depth [32], such as use of first principlecalculations, origin of the enhanced visible light absorption inN-doped anatase TiO
2[44], or approaches to combine TiO
2
with another mineral such as schorl.
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper.
Acknowledgment
This research was financially supported by the NationalScience Council of Taiwan ROC under Grants nos. NSC-100-2221-E-005-007 and NSC-101-2120-M-005-001.
References
[1] Y.-H. Lin, H.-H. Tseng, M.-Y. Wey, and M.-D. Lin, “Character-istics, morphology, and stabilization mechanism of PAA250K-stabilized bimetal nanoparticles,” Colloids and Surfaces A:Physicochemical and Engineering Aspects, vol. 349, no. 1–3, pp.137–144, 2009.
[2] Y.-H. Lin, H.-H. Tseng, M.-Y. Wey, and M.-D. Lin, “Charac-teristics of two types of stabilized nano zero-valent iron andtransport in porous media,” Science of the Total Environment,vol. 408, no. 10, pp. 2260–2267, 2010.
Journal of Nanomaterials 9
[3] Y.-T. Lin, C.-H.Weng, and T.W. Tzeng, “Photocatalysis and cat-alytic properties of nano-sized N-TiO
2Catalyst synthesized by
Sol-gel methods,” Journal of Advanced Oxidation Technologies,vol. 13, no. 3, pp. 297–304, 2010.
[4] T. C. Jagadale, S. P. Takale, R. S. Sonawane et al., “N-dopedTiO2nanoparticle based visible light photocatalyst by modified
peroxide sol-gel method,” Journal of Physical Chemistry C, vol.112, no. 37, pp. 14595–14602, 2008.
[5] L. Sun, J. Li, C. Wang et al., “Ultrasound aided photochemicalsynthesis of Ag loaded TiO
2nanotube arrays to enhance pho-
tocatalytic activity,” Journal of Hazardous Materials, vol. 171, no.1–3, pp. 1045–1050, 2009.
[6] Y.-K. Lai, J.-Y. Huang, H.-F. Zhang et al., “Nitrogen-doped TiO2
nanotube array films with enhanced photocatalytic activityunder various light sources,” Journal of Hazardous Materials,vol. 184, no. 1–3, pp. 855–863, 2010.
[7] Y. Tang, P. Wee, Y. Lai et al., “Hierarchical TiO2nanoflakes
and nanoparticles hybrid structure for improved photocatalyticactivity,”The Journal of Physical Chemistry C, vol. 116, no. 4, pp.2772–2780, 2012.
[8] M. Sathish, B. Viswanathan, R. P. Viswanath, and C. S. Gopi-nath, “Synthesis, characterization, electronic structure, and pho-tocatalytic activity of nitrogen-doped TiO
2nanocatalyst,” Chem-
istry of Materials, vol. 17, no. 25, pp. 6349–6353, 2005.[9] B. F. Abramović, D. V. Šojić, V. B. Anderluh, N. D. Abazović, and
M. I. Čomor, “Nitrogen-doped TiO2suspensions in photo-
catalytic degradation of mecoprop and (4-chloro-2-methyl-phenoxy)acetic acid herbicides using various light sources,”Desalination, vol. 244, no. 1–3, pp. 293–302, 2009.
[10] Y. Ma, J. Zhang, B. Tian, F. Chen, and L. Wang, “Synthesis andcharacterization of thermally stable Sm,N co-doped TiO
2with
highly visible light activity,” Journal of HazardousMaterials, vol.182, no. 1–3, pp. 386–393, 2010.
[11] S.-I. In, P. C. K. Vesborg, B. L. Abrams, Y. Hou, and I. Chork-endorff, “A comparative study of two techniques for determin-ing photocatalytic activity of nitrogen doped TiO
2nanotubes
under visible light irradiation: photocatalytic reduction of dyeand photocatalytic oxidation of organic molecules,” Journal ofPhotochemistry and Photobiology A: Chemistry, vol. 222, no. 1,pp. 258–262, 2011.
[12] Z. Xie, Y. Zhang, X. Liu et al., “Visible light photoelectrochem-ical properties of N-doped TiO
2-nanorod arrays from TiN,”
Journal of Nanomaterials, vol. 2013, Article ID 930950, 8 pages,2013.
[13] Y.-T. Lin, C.-H. Weng, Y.-H. Lin, C.-C. Shiesh, and F.-Y. Chen,“Effect of C content and calcination temperature on the pho-tocatalytic activity of C-doped TiO
2catalyst,” Separation and
Purification Technology, vol. 116, pp. 114–123, 2013.[14] X. Cheng, H. Liu, Q. Chen, J. Li, and P. Wang, “Construction
of N, S codoped TiO2NCs decorated TiO
2nano-tube array
photoelectrode and its enhanced visible light photocatalyticmechanism,” Electrochimica Acta, vol. 103, pp. 134–142, 2013.
[15] C. H. Park, S. B. Zhang, and S.-H.Wei, “Origin of p-type dopingdifficulty in ZnO: the impurity perspective,” Physical Review B,vol. 66, no. 7, Article ID 073202, 2002.
[16] S. Sato, R. Nakamura, and S. Abe, “Visible-light sensitizationof TiO
2photocatalysts by wet-method N doping,” Applied
Catalysis A: General, vol. 284, no. 1-2, pp. 131–137, 2005.
[17] Y.-T. Lin, C.-H. Weng, H.-J. Hsu, Y.-H. Lin, and C.-C. Shiesh,“The synergistic effect of nitrogen dopant and calcinationtemperature on the visible-light-induced photoactivity of N-doped TiO
2,” International Journal of Photoenergy, vol. 2013,
Article ID 268723, 13 pages, 2013.[18] R. Asahi, T. Morikawa, T. Ohwaki, K. Aoki, and Y. Taga, “Vis-
ible-light photocatalysis in nitrogen-doped titanium oxides,”Science, vol. 293, no. 5528, pp. 269–271, 2001.
[19] C. Di Valentin, E. Finazzi, G. Pacchioni et al., “N-doped TiO2:
theory and experiment,” Chemical Physics, vol. 339, no. 1–3, pp.44–56, 2007.
[20] O. Diwald, T. L. Thompson, T. Zubkov, E. G. Goralski, S. D.Walck, and J. T. Yates Jr., “Photochemical activity of nitrogen-doped rutile TiO
2(110) in visible light,” Journal of Physical
Chemistry B, vol. 108, no. 19, pp. 6004–6008, 2004.[21] X. Chen and C. Burda, “Photoelectron spectroscopic inves-
tigation of nitrogen-doped titania nanoparticles,” Journal ofPhysical Chemistry B, vol. 108, no. 40, pp. 15446–15449, 2004.
[22] S. Hu, A. Wang, X. Li, and H. Löwe, “Hydrothermal synthesisof well-dispersed ultrafine N-doped TiO
2nanoparticles with
enhanced photocatalytic activity under visible light,” Journal ofPhysics and Chemistry of Solids, vol. 71, no. 3, pp. 156–162, 2010.
[23] Y. Zhao, X. Qiu, and C. Burda, “The effects of sintering onthe photocatalytic activity of N-Doped TiO
2nanoparticles,”
Chemistry of Materials, vol. 20, no. 8, pp. 2629–2636, 2008.[24] S. Y. Ye, Q. M. Tian, X. L. Song, and S. C. Luo, “Photo-
electrocatalytic degradation of ethylene by a combination ofTiO2and activated carbon felts,” Journal of Photochemistry and
Photobiology A: Chemistry, vol. 208, no. 1, pp. 27–35, 2010.[25] S. Yamazaki, S. Tanaka, and H. Tsukamoto, “Kinetic studies
of oxidation of ethylene over a TiO2photocatalyst,” Journal of
Photochemistry and Photobiology A: Chemistry, vol. 121, no. 1,pp. 55–61, 1999.
[26] S. Sato, “Photocatalytic activity of NO𝑥-doped TiO
2in the
visible light region,” Chemical Physics Letters, vol. 123, no. 1-2,pp. 126–128, 1986.
[27] R. A. Spurr, “Quantitative analysis of anatase-rutile mixtureswith an X-ray diffractometer,” Analytical Chemistry, vol. 29, no.5, pp. 760–762, 1957.
[28] J. Yu, M. Zhou, B. Cheng, and X. Zhao, “Preparation, character-ization and photocatalytic activity of in situ N,S-codoped TiO
2
powders,” Journal of Molecular Catalysis A: Chemical, vol. 246,no. 1-2, pp. 176–184, 2006.
[29] Y. Luan, L. Jing, M. Xie et al., “Synthesis of efficient N-con-taining TiO
2photocatalysts with high anatase thermal stability
and the effects of the nitrogen residue on the photoinducedcharge separation,” Physical Chemistry Chemical Physics, vol. 14,no. 4, pp. 1352–1359, 2012.
[30] N. D. Abazović, A.Montone, L.Mirenghi, I. A. Janković, andM.I. Čomor, “TiO
2doped with nitrogen: synthesis and character-
ization,” Journal of Nanoscience and Nanotechnology, vol. 8, no.2, pp. 613–618, 2008.
[31] N. C. Saha and H. G. Tompkins, “Titanium nitride oxidationchemistry: an x-ray photoelectron spectroscopy study,” Journalof Applied Physics, vol. 72, no. 7, pp. 3072–3079, 1992.
[32] X. Qiu and C. Burda, “Chemically synthesized nitrogen-dopedmetal oxide nanoparticles,” Chemical Physics, vol. 339, no. 1–3,pp. 1–10, 2007.
[33] T. Morikawa, R. Asahi, T. Ohwaki, K. Aoki, and Y. Taga, “Band-gap narrowing of titanium dioxide by nitrogen doping,” Japa-nese Journal of Applied Physics, vol. 40, no. 6, pp. L561–L563,2001.
10 Journal of Nanomaterials
[34] I. Nakamura, N. Negishi, S. Kutsuna, T. Ihara, S. Sugihara, andK. Takeuchi, “Role of oxygen vacancy in the plasma-treatedTiO2photocatalyst with visible light activity for NO removal,”
Journal of Molecular Catalysis A: Chemical, vol. 161, no. 1-2, pp.205–212, 2000.
[35] Z.Wu, F.Dong,W.Zhao, and S.Guo, “Visible light induced elec-tron transfer process over nitrogen doped TiO
2nanocrystals
prepared by oxidation of titaniumnitride,” Journal of HazardousMaterials, vol. 157, no. 1, pp. 57–63, 2008.
[36] T. Ihara,M.Miyoshi, Y. Iriyama,O.Matsumoto, and S. Sugihara,“Visible-light-active titanium oxide photocatalyst realized byan oxygen-deficient structure and by nitrogen doping,” AppliedCatalysis B: Environmental, vol. 42, no. 4, pp. 403–409, 2003.
[37] N. Serpone, “Is the band gap of pristine TiO2narrowed by
anion- and cation-doping of titanium dioxide in second-gener-ation photocatalysts?”The Journal of Physical Chemistry B, vol.110, no. 48, pp. 24287–24293, 2006.
[38] Z. Lin, A. Orlov, R.M. Lambert, andM. C. Payne, “New insightsinto the origin of visible light photocatalytic activity of nitrogen-doped and oxygen-deficient anatase TiO
2,” Journal of Physical
Chemistry B, vol. 109, no. 44, pp. 20948–20952, 2005.[39] A. Nambu, J. Graciani, J. A. Rodriguez, Q. Wu, E. Fujita, and
J. F. Sanz, “N doping of TiO2(110): photoemission and density-
functional studies,” Journal of Chemical Physics, vol. 125, no. 9,Article ID 094706, 2006.
[40] T. Ozawa, M. Iwasaki, H. Tada, T. Akita, K. Tanaka, and S.Ito, “Low-temperature synthesis of anatase-brookite compositenanocrystals: the junction effect on photocatalytic activity,”Journal of Colloid and Interface Science, vol. 281, no. 2, pp. 510–513, 2005.
[41] M. Batzill, E. H.Morales, andU. Diebold, “Influence of nitrogendoping on the defect formation and surface properties of TiO
2
rutile and anatase,” Physical Review Letters, vol. 96, no. 2, ArticleID 026103, 2006.
[42] H. Chen, A. Nambu, W. Wen et al., “Reaction of NH3with
titania: N-doping of the oxide and TiN formation,”The Journalof Physical Chemistry C, vol. 111, no. 3, pp. 1366–1372, 2007.
[43] H. Fu, L. Zhang, S. Zhang, Y. Zhu, and J. Zhao, “Electron spinresonance spin-trapping detection of radical intermediates inN-doped TiO
2-assisted photodegradation of 4-chlorophenol,”
Journal of Physical Chemistry B, vol. 110, no. 7, pp. 3061–3065,2006.
[44] M. Harb, P. Sautet, and P. Raybaud, “Origin of the enhancedvisible-light absorption in N-doped bulk anatase TiO
2from
first-principles calculations,” The Journal of Physical ChemistryC, vol. 115, no. 39, pp. 19394–19404, 2011.
Submit your manuscripts athttp://www.hindawi.com
ScientificaHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
CorrosionInternational Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Polymer ScienceInternational Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
CeramicsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
CompositesJournal of
NanoparticlesJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of
Biomaterials
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
NanoscienceJournal of
TextilesHindawi Publishing Corporation http://www.hindawi.com Volume 2014
Journal of
NanotechnologyHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Journal of
CrystallographyJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
The Scientific World JournalHindawi Publishing Corporation http://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
CoatingsJournal of
Advances in
Materials Science and EngineeringHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Smart Materials Research
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
MetallurgyJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
BioMed Research International
MaterialsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Nano
materials
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Journal ofNanomaterials