69
Nokia Siemens Networks GSM/EDGE BSS, rel. RG10(BSS), operating documentation, issue 06 Reference 3 Resource Access Measurement DN9813745 Issue 11-3 Approval Date 2010-08-05

Resource Access Measurements.pdf

Embed Size (px)

Citation preview

Nokia Siemens Networks GSM/EDGE BSS, rel. RG10(BSS), operating documentation, issue 06

Reference

3 Resource Access Measurement

DN9813745

Issue 11-3Approval Date 2010-08-05

2 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807d4c45

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2010. All rights reserved

f Important Notice on Product Safety Elevated voltages are inevitably present at specific points in this electrical equipment. Some of the parts may also have elevated operating temperatures.

Non-observance of these conditions and the safety instructions can result in personal injury or in property damage.

Therefore, only trained and qualified personnel may install and maintain the system.

The system complies with the standard EN 60950 / IEC 60950. All equipment connected has to comply with the applicable safety standards.

The same text in German:

Wichtiger Hinweis zur Produktsicherheit

In elektrischen Anlagen stehen zwangsläufig bestimmte Teile der Geräte unter Span-nung. Einige Teile können auch eine hohe Betriebstemperatur aufweisen.

Eine Nichtbeachtung dieser Situation und der Warnungshinweise kann zu Körperverlet-zungen und Sachschäden führen.

Deshalb wird vorausgesetzt, dass nur geschultes und qualifiziertes Personal die Anlagen installiert und wartet.

Das System entspricht den Anforderungen der EN 60950 / IEC 60950. Angeschlossene Geräte müssen die zutreffenden Sicherheitsbestimmungen erfüllen.

DN9813745Issue 11-3

3

3 Resource Access Measurement

Id:0900d805807d4c45

Table of ContentsThis document has 69 pages.

Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1 3 Resource Access Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2 Counters of Resource Access Measurement . . . . . . . . . . . . . . . . . . . . 112.1 003000 / PAGING MESSAGES SENT TO BTS . . . . . . . . . . . . . . . . . . 112.2 003001 / IMMEDIATE ASSIGNMENT MESSAGES SENT TO BTS . . . 112.3 003002 / IMMEDIATE ASSIGNMENT REJECT MESSAGES SENT TO

BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122.4 003003 / SMS BC REQUEST MESSAGES SENT TO BTS . . . . . . . . . 122.5 003004 / CHANNEL REQUEST MESSAGES RECEIVED FROM BTS 132.6 003005 / DELETE IND MESSAGES RECEIVED FROM BTS. . . . . . . . 142.7 003006 / AVE RACH SLOT COUNT . . . . . . . . . . . . . . . . . . . . . . . . . . . 142.8 003007 / RES ACC DENOMINATOR 1 . . . . . . . . . . . . . . . . . . . . . . . . . 152.9 003008 / AVE PCH LOAD ON CCCH . . . . . . . . . . . . . . . . . . . . . . . . . . 152.10 003009 / RES ACC DENOMINATOR 2 . . . . . . . . . . . . . . . . . . . . . . . . . 162.11 003010 / PEAK RACH LOAD ON CCCH. . . . . . . . . . . . . . . . . . . . . . . . 162.12 003011 / PEAK PCH LOAD ON CCCH . . . . . . . . . . . . . . . . . . . . . . . . . 172.13 003012 / SUCCESS SEIZURE FOR MOBILE TERM CALL . . . . . . . . . 182.14 003013 / SUCCESS SEIZURE FOR MOBILE ORIG CALL. . . . . . . . . . 182.15 003014 / AVE RACH BUSY COUNT . . . . . . . . . . . . . . . . . . . . . . . . . . . 192.16 003015 / RES ACC DENOMINATOR 3 . . . . . . . . . . . . . . . . . . . . . . . . . 192.17 003016 / AVE RACH ACCESS COUNT . . . . . . . . . . . . . . . . . . . . . . . . 202.18 003017 / RES ACC DENOMINATOR 4 . . . . . . . . . . . . . . . . . . . . . . . . . 212.19 003018 / MIN PAGING BUF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212.20 003019 / SDCCH LOC UPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222.21 003020 / SDCCH CALL RE EST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222.22 003021 / SDCCH EMERG CALL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232.23 003022 / TCH EMERG CALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232.24 003023 / TCH MTC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242.25 003024 / TCH MOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242.26 003025 / TCH CALL RE EST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252.27 003026 / SUCC TCH SMS EST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252.28 003027 / UNSUCC TCH SMS EST . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262.29 003028 / SUCC SDCCH SMS EST . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272.30 003029 / UNSUCC SDCCH SMS EST . . . . . . . . . . . . . . . . . . . . . . . . . 272.31 003030 / GHOST CCCH RES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282.32 003031 / REJ SEIZ ATT DUE DIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . 282.33 003032 / TRX IN EXT AREA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292.34 003033 / IMSI DETACH SDCCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302.35 003034 / IMSI DETACH TCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302.36 003035 / MAX PAGING BUFFER CAPA. . . . . . . . . . . . . . . . . . . . . . . . 312.37 003036 / AVE PAGING BUFFER CAPA . . . . . . . . . . . . . . . . . . . . . . . . 312.38 003037 / RES ACC DENOMINATOR 5 . . . . . . . . . . . . . . . . . . . . . . . . . 322.39 003038 / DELETE PAGING COMMAND. . . . . . . . . . . . . . . . . . . . . . . . 33

4 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807d4c45

2.40 003039 / BCSU OVERLOAD LOWER LIMIT . . . . . . . . . . . . . . . . . . . . . 332.41 003040 / BCSU OVERLOAD UPPER LIMIT . . . . . . . . . . . . . . . . . . . . . 342.42 003041 / BCSU OVERLOAD DELETED RACH . . . . . . . . . . . . . . . . . . . 352.43 003042 / TRX DIAGNOSTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352.44 003043 / TRX DIAGNOSTICS FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . 362.45 003044 / SUCC SEIZ SUPPLEM SERV. . . . . . . . . . . . . . . . . . . . . . . . . 362.46 003045 / TCH SUPPLEM SERV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372.47 003046 / AVE PCH GB LOAD ON CCCH . . . . . . . . . . . . . . . . . . . . . . . 372.48 003047 / RES ACC DENOMINATOR 6 . . . . . . . . . . . . . . . . . . . . . . . . . 382.49 003048 / AVE PAGING GB BUF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392.50 003049 / RES ACC DENOMINATOR 7 . . . . . . . . . . . . . . . . . . . . . . . . . 392.51 003050 / MAX PAGING GB BUF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402.52 003051 / AVE PAGING LOAD AIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412.53 003052 / RES ACC DENOMINATOR 8 . . . . . . . . . . . . . . . . . . . . . . . . . 412.54 003053 / AVE DRX AGCH LOAD AIR . . . . . . . . . . . . . . . . . . . . . . . . . . 422.55 003054 / RES ACC DENOMINATOR 9 . . . . . . . . . . . . . . . . . . . . . . . . . 432.56 003055 / AVE NON DRX AGCH LOAD AIR . . . . . . . . . . . . . . . . . . . . . . 432.57 003056 / RES ACC DENOMINATOR 10 . . . . . . . . . . . . . . . . . . . . . . . . 442.58 003057 / PS PAGING MSG SENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 452.59 003058 / CS PAGING MSG SENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 452.60 003059 / CALL ASSIGN AFTER SMS . . . . . . . . . . . . . . . . . . . . . . . . . . 462.61 003060 / SPARE003060. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 462.62 003061 / SPARE003061. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472.63 003062 / SPARE003062. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472.64 003063 / SPARE003063. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482.65 003064 / SUCC MO SMS SDCCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482.66 003065 / UNSUCC MO SMS SDCCH . . . . . . . . . . . . . . . . . . . . . . . . . . 49

3 Signalling charts of Resource Access Measurement . . . . . . . . . . . . . . . 50

DN9813745Issue 11-3

5

3 Resource Access Measurement

Id:0900d805807d4c45

List of FiguresFigure 1 Basic call without counters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Figure 2 Basic call without counters (cont.). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Figure 3 Basic call with counters.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Figure 4 FACCH call setup due to SDCCH congestion. . . . . . . . . . . . . . . . . . . . 53Figure 5 Ghost reservation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Figure 6 Busy AGCH-channel.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Figure 7 Unsuccessful channel request. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Figure 8 SMS broadcast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Figure 9 Mobile originating SMS on a TCH.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Figure 10 Mobile terminating SMS on a TCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Figure 11 Mobile originating SMS on FACCH.. . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Figure 12 Mobile terminating SMS on FACCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Figure 13 Mobile originating SMS on an SDCCH. . . . . . . . . . . . . . . . . . . . . . . . . . 59Figure 14 Mobile terminating SMS on an SDCCH. . . . . . . . . . . . . . . . . . . . . . . . . 60Figure 15 Mobile originating unsuccessful SMS on a TCH.. . . . . . . . . . . . . . . . . . 61Figure 16 Mobile terminating unsuccessful SMS on a TCH. . . . . . . . . . . . . . . . . . 62Figure 17 Mobile originating unsuccessful SMS on FACCH.. . . . . . . . . . . . . . . . . 63Figure 18 Mobile terminating unsuccessful SMS on FACCH. . . . . . . . . . . . . . . . . 64Figure 19 Mobile originating unsuccessful SMS on an SDCCH. . . . . . . . . . . . . . . 65Figure 20 Mobile terminating unsuccessful SMS on an SDCCH. . . . . . . . . . . . . . 65Figure 21 CCCH load indication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Figure 22 CCCH Load Indication if GPRS is activated in BTS and other conditions are

valid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Figure 23 Unsuccessful channel requests because of BCSU overload. . . . . . . . . 68Figure 24 PS Paging in GPRS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Figure 25 CS Paging in GPRS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

6 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807d4c45

List of TablesTable 1 Measurement description of Resource Access Measurement . . . . . . . . . 8Table 2 Counters of Resource Access Measurement . . . . . . . . . . . . . . . . . . . . . 8

DN9813745Issue 11-3

7

3 Resource Access Measurement Summary of changes

Id:0900d805807d4c53

Summary of changesChanges between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues.

Changes made between issues 11-3 and 11-2Target name is modified with TSL information.

Changes made between issues 11-2 and 11-1Editorial changes are made for updated field of counter 003010.

Changes made between issues 11-1 and 11-0The Description field of the counter 003032 is modified.

Changes made between issues 11-0 and 10-0The updated field of the counters 003001 and 003004 are modified.

Changes made between issues 10-0 and 9-2Counter table format changed.

8 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807d46ac

3 Resource Access Measurement

1 3 Resource Access MeasurementResource Access Measurement registers information on all common control channels (CCCH) of the base station controller. The recorded items of data comprise the number of messages sent to the Abis interface. The messages are sorted according to message type, average load on control channels, and the number of traffic channel seizures for mobile originating (MOC) and terminating calls (MTC). Signalling charts are drawn with the accuracy of message interface.

Measurement description

Measurement counters

MeasurementMeasurement ID Measurement abbreviation

Resource Access Measurement3CCCH_ACC

Product BSC

Product software release S1

Target name BTS+TRX+TSL

Table 1 Measurement description of Resource Access Measurement

Counter Counter number

Paging messages sent to BTS 003000

Immediate assignment messages sent to BTS 003001

Immediate assignment reject messages sent to BTS 003002

SMS CB request messages sent to BTS 003003

Channel request messages received from BTS 003004

Delete indication messages received from BTS 003005

Average RACH slot counter 003006

Resource access denominator 1 003007

Average PCH load on CCCH 003008

Resource access denominator 2 003009

Peak RACH load on CCCH 003010

Peak PCH load on CCCH 003011

Success seizure for MTC 003012

Success seizure for MOC 003013

Average RACH busy counter 003014

Resource access denominator 3 003015

Average RACH access counter 003016

Resource access denominator 4 003017

Table 2 Counters of Resource Access Measurement

DN9813745Issue 11-3

9

3 Resource Access Measurement 3 Resource Access Measurement

Id:0900d805807d46ac

Minimum paging buffer 003018

SDCCH location update 003019

SDCCH call re-establishment 003020

SDCCH emergency call 003021

TCH emergency call 003022

TCH MTC 003023

TCH MOC 003024

TCH call re-establishment 003025

Success TCH SMS establishment 003026

Unsuccessful TCH SMS establishment 003027

Success SDCCH SMS establishment 003028

Unsuccessful SDCCH SMS establishment 003029

Ghost CCCH reservation 003030

Rejected seizure attempt due to distance 003031

TRX in extended area 003032

IMSI detach SDCCH 003033

IMSI detach TCH 003034

Maximum paging buffer capacity 003035

Average paging buffer capacity 003036

Resource access denominator 5 003037

Delete paging command 003038

BCSU overload lower limit 003039

BCSU overload upper limit 003040

BCSU overload deleted RACH 003041

TRX diagnostics 003042

TRX diagnostics fault 003043

Successful seizures of SDCCHs 003044

Successful seizures of TCHs 003045

Paging load paging buffer space on Gb-interference 003046

Resource access denominator 6 003047

Average buffer occupancy percentage 003048

Resource access denominator 7 003049

Maximum buffer occupancy percentage 003050

Average CCCH load radio block occupancy paging 003051

Resource access denominator 8 003052

Average DRX AGCH 003053

Counter Counter number

Table 2 Counters of Resource Access Measurement (Cont.)

10 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807d46ac

3 Resource Access Measurement

Related topics

• Counters of Resource Access Measurement • Signalling charts of Resource Access Measurement • BSC Statistics Administration • Activating and Testing BSS6037: Improved Solution for Extended Cell • BSC Measurement Counters Displaying Program (FOXMEA) • Performance Measurements • EDGE System Feature Description • Extended Cell Range • BSS21538: Extended CCCH

Resource access denominator 9 003054

Average NON-DRX AGCH 003055

Resource access denominator 10 003056

PS paging command 003057

CS paging command 003058

Call assign after SMS 003059

Spare 003060

Spare 003061

Spare 003062

Spare 003063

Successful mobile-originated SMS establishment on an SDCCH

003064

Unsuccessful mobile-originated SMS establishment on an SDCCH

003065

Counter Counter number

Table 2 Counters of Resource Access Measurement (Cont.)

DN9813745Issue 11-3

11

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2 Counters of Resource Access Measurement

2.1 003000 / PAGING MESSAGES SENT TO BTS

2.2 003001 / IMMEDIATE ASSIGNMENT MESSAGES SENT TO BTS

Counter ID: 003000 Network element name: PAGING MESSAGES SENT TO BTS

Version: 3.0 NetAct name: PAGING_MSG_SENT

Description: Number of PAGING_COMMAND messages sent to the BTS.

Updated: When a PAGING_COMMAND message is sent to the BTS.

See figure Basic call with counters.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:

Counter ID: 003001 Network element name: IMMEDIATE ASSIGNMENT MESSAGES SENT TO BTS

Version: 3.1 NetAct name: IMM_ASSGN_SENT

Description: Number of IMMEDIATE_ASSIGN_COMMAND messages sent to the BTS.

Updated: When an IMMEDIATE_ASSIGN_COMMAND message is sent to the BTS.

See figures:- Basic call with counters- Busy AGCH Channel

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

12 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.3 003002 / IMMEDIATE ASSIGNMENT REJECT MESSAGES SENT TO BTS

2.4 003003 / SMS BC REQUEST MESSAGES SENT TO BTS

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:

Counter ID: 003002 Network element name: IMMEDIATE ASSIGNMENT REJECT MESSAGES SENT TO BTS

Version: 3.0 NetAct name: IMM_ASSGN_REJ

Description: Number of IMMEDIATE_ASSIGNMENT_REJECT messages sent to the BTS.

Updated: This counter is updated when an IMMEDIATE_ASSIGNMENT_REJECT message is packed and sent to the BTS. The message can include one to four imme-diate assignment rejects.

The IMMEDIATE_ASSIGNMENT_REJECT message is sent to MS in the following cases:No free SDCCH.Abis interface process has no internal resources to handle the request.

See figure Unsuccessful channel request

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:S6

Counter ID: 003003 Network element name: SMS BC REQUEST MESSAGES SENT TO BTS

Version: 3.0 NetAct name: SMS_BC_REQ_SENT

Description: Number of SMS_BROADCAST_REQUEST messages sent to the BTS.

DN9813745Issue 11-3

13

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.5 003004 / CHANNEL REQUEST MESSAGES RECEIVED FROM BTS

Updated: When all 4 SMS_BROADCAST_REQUEST messages are sent to the BTS.

See figure SMS broadcast

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:

Counter ID: 003004 Network element name: CHANNEL REQUEST MESSAGES RECEIVED FROM BTS

Version: 3.1 NetAct name: CH_REQ_MSG_REC

Description: Number of CHANNEL_REQUIRED messages received from the BTS.

Updated: When a CHANNEL_REQUIRED message is received from the BTS. These requests are related to CSW channels. PSW channel requests have their own counter 072082.

See figures:- Basic call with counters- Ghost reservation- Busy AGCH channel- Unsuccesful channel request- Unsuccesful channel requests due to BCSU overload

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:

14 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.6 003005 / DELETE IND MESSAGES RECEIVED FROM BTS

2.7 003006 / AVE RACH SLOT COUNT

Counter ID: 003005 Network element name: DELETE IND MESSAGES RECEIVED FROM BTS

Version: 3.0 NetAct name: DEL_IND_MSG_REC

Description: Number of DELETE_INDICATION messages received from the BTS.

Updated: When a DELETE_INDICATION message is received from the BTS.

See figure Busy AGCH Channel

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:

Counter ID: 003006 Network element name: AVE RACH SLOT COUNT

Version: 3.0 NetAct name: AVE_RACH_SLOT

Description: Average number of the RACH slots on a CCCH.

Counter 003007 is updated along with this counter.

Updated: When the value of the RACH load is received in a CCCH_LOAD_INDICATION message from the BTS during a measurement period. The new value of the RACH load is added to the previous value, and the number of events is increased by one.

See figure CCCH load indication.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003007: RES ACC DENOMINATOR 1

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

DN9813745Issue 11-3

15

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.8 003007 / RES ACC DENOMINATOR 1

2.9 003008 / AVE PCH LOAD ON CCCH

Exceptions to related standard:

Used from release: S1 Definition updated in release:

Counter ID: 003007 Network element name: RES ACC DENOMINATOR 1

Version: 3.0 NetAct name: RES_ACC_DENOM1

Description: Denominator of the average RACH slot number (always > 0).

Counter 003006 is updated along with this counter.

Updated: See figure CCCH load indication

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003006: AVE RACH SLOT COUNT

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:

Counter ID: 003008 Network element name: AVE PCH LOAD ON CCCH

Version: 3.0 NetAct name: AVE_PCH_LOAD

Description: When divided by the value of counter 003009, this counter tells the Average PCH load on a CCCH. It indicates the remaining space for Paging Commands associated with this CCCH timeslot, given as the number of additional Paging Commands that it is possible to store. The smaller the value, the greater the load on the PCH.

This counter is updated along with counter 003009.

Updated: Cumulatively during the measurement period every time when the latest value of the PCH load is received in a CCCH_LOAD_INDICATION message from the BTS.

See figure CCCH load indication.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

16 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.10 003009 / RES ACC DENOMINATOR 2

2.11 003010 / PEAK RACH LOAD ON CCCH

Dependencies with other counters:

003009: RES ACC DENOMINATOR 2

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:

Counter ID: 003009 Network element name: RES ACC DENOMINATOR 2

Version: 3.0 NetAct name: RES_ACC_DENOM2

Description: Denominator of the average PCH load on CCCH (always > 0).

Counter 003008 is updated along with this counter.

Updated: See figure CCCH load indication.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003008: AVE PCH LOAD ON CCCH

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:

Counter ID: 003010 Network element name: PEAK RACH LOAD ON CCCH

Version: 3.0 NetAct name: PEAK_RACH_BUSY_COUNT_C

Description: Peak value of the number of busy RACHs on a CCCH.

DN9813745Issue 11-3

17

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.12 003011 / PEAK PCH LOAD ON CCCH

Updated: When the value of the RACH load received in a CCCH_LOAD_INDICATION message exceeds the previous value of the RACH load during the measurement period.

NOTE! This RACH counter is triggered when the RX Level is above -100dBm. Other detection methods (like CRC or S/N) are not applied. This means that high load on RACH may occur even without a significant number of CHANNEL_REQUIRED mes-sages. For example, RACHs from different MSs can clash and cause a high signal level, but the decoding does not find any detectable RACH. The interference causes lot of bursts that trigger the counter, but these bursts are then filtered out in the detec-tion.

See figure CCCH load indication.

Logical type: Max Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:

Counter ID: 003011 Network element name: PEAK PCH LOAD ON CCCH

Version: 3.0 NetAct name: PEAK_PCH_LOAD

Description: This counter is NOT relevant.

This counter has been replaced by counter 003018 MIN PAGING BUF.

Updated:

Logical type: Trigger type: Sampling interval:

Unit: Range: Example values:

Dependencies with other counters:

003018: MIN PAGING BUF

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

18 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.13 003012 / SUCCESS SEIZURE FOR MOBILE TERM CALL

2.14 003013 / SUCCESS SEIZURE FOR MOBILE ORIG CALL

Used from release: S1 Definition updated in release:

Counter ID: 003012 Network element name: SUCCESS SEIZURE FOR MOBILE TERM CALL

Version: 3.0 NetAct name: SUCC_SEIZ_TERM

Description: Number of successful seizures of SDCCHs for an MTC.

Updated: When an ESTABLISH_INDICATION message with paging response is received on SDCCH from the BTS.

See figure Basic call with counters.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:

Counter ID: 003013 Network element name: SUCCESS SEIZURE FOR MOBILE ORIG CALL

Version: 3.0 NetAct name: SUCC_SEIZ_ORIG

Description: Number of successful seizures for SDCCH for an MOC.

Updated: When an ESTABLISH_INDICATION message with CM service request is received on SDCCH from the BTS.

Note that this counter is updated also in case of an SMS or Supplementary Service Requests.

See figure Basic call with counters.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

DN9813745Issue 11-3

19

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.15 003014 / AVE RACH BUSY COUNT

2.16 003015 / RES ACC DENOMINATOR 3

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:

Counter ID: 003014 Network element name: AVE RACH BUSY COUNT

Version: 3.0 NetAct name: AVE_RACH_BUSY

Description: Average number of busy RACHs on a CCCH.

Counter 003015 is updated along with this counter.

Updated: When the value of the RACH load is received in a CCCH_LOAD_INDICATION message from the BTS during a measurement period. The number of busy RACHs is added to the previous value and the number of the events is increased by one.

NOTE! This RACH counter is triggered when the RX Level is above -100dBm. Other detection methods (like CRC or S/N) are not applied. This means that high load on RACH may occure even without a significant number of CHANNEL_REQUIRED mes-sages. For example, RACHs from different MSs can clash and cause a high signal level, but the decoding does not find any detectable RACH. The interference causes lots of bursts that trigger the counter, but these bursts are then filtered out in the detection.

See figure CCCH load indication.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003015: RES ACC DENOMINATOR 3

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:

Counter ID: 003015 Network element name: RES ACC DENOMINATOR 3

Version: 3.0 NetAct name: RES_ACC_DENOM3

20 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.17 003016 / AVE RACH ACCESS COUNT

Description: Denominator of the average number of busy RACHs (always > 0).

Counter 003014 is updated along with this counter.

Updated: See figure CCCH load indication.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003014: AVE RACH BUSY COUNT

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:

Counter ID: 003016 Network element name: AVE RACH ACCESS COUNT

Version: 3.0 NetAct name: AVE_RACH_ACCESS

Description: Number of average RACH accesses on a CCCH.

Counter 003017 is updated along with this counter.

Updated: When the value of the RACH load is received in a CCCH_LOAD_INDICATION message from the BTS during a measurement period. The number of RACH accesses is added to the previous value and the number of events is increased by one.

NOTE! This counter is updated by RACH bursts above the -100 dBm level that have passed the detection (CRC, S/N) in the BTS.

See figure CCCH load indication.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003017: RES ACC DENOMINATOR 4

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

DN9813745Issue 11-3

21

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.18 003017 / RES ACC DENOMINATOR 4

2.19 003018 / MIN PAGING BUF

Used from release: S1 Definition updated in release:

Counter ID: 003017 Network element name: RES ACC DENOMINATOR 4

Version: 3.0 NetAct name: RES_ACC_DENOM4

Description: Denominator of the average number of RACH accesses (always > 0).

Counter 003016 is updated along with this counter.

Updated: See figure CCCH load indication.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003016: AVE RACH ACCESS COUNT

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S1 Definition updated in release:

Counter ID: 003018 Network element name: MIN PAGING BUF

Version: 3.0 NetAct name: MIN_PAGING_BUF

Description: Minimum size of the paging buffer on a CCCH (Peak value of the average PCH load: the smaller the value, the greater the load on the PCH).

Updated: When the value of the PCH load with the size of the paging buffer received in a CCCH_LOAD_INDICATION message from the BTS is smaller than the previous value during a measurement period. 0xFFFFFFFF means unknown.

See figure CCCH load indication.

Logical type: Min Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

22 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.20 003019 / SDCCH LOC UPD

2.21 003020 / SDCCH CALL RE EST

Exceptions to related standard:

Used from release: S2 Definition updated in release:

Counter ID: 003019 Network element name: SDCCH LOC UPD

Version: 3.0 NetAct name: SDCCH_LOC_UPD

Description: Number of successful seizures of SDCCHs for location update.

Updated: When an ESTABLISH_INDICATION message with request for a location update is received on SDCCH from the BTS.

See figure Basic call with counters.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S2 Definition updated in release:

Counter ID: 003020 Network element name: SDCCH CALL RE EST

Version: 3.0 NetAct name: SDCCH_CALL_RE_EST

Description: Number of successful SDCCH seizures for call re-establishment attempts.

Updated: When an ESTABLISHMENT_INDICATION message for a call re-establish-ment is received on SDCCH from the BTS. Note that this counter counts only the number of re-establisment attempts on SDCCH. Counter 057022 gives the number of SDCCH re-establishment assignments.

See figure Basic call with counters.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

DN9813745Issue 11-3

23

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.22 003021 / SDCCH EMERG CALL

2.23 003022 / TCH EMERG CALL

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S3 Definition updated in release:

Counter ID: 003021 Network element name: SDCCH EMERG CALL

Version: 3.0 NetAct name: SDCCH_EMERG_CALL

Description: Number of successful seizures of SDCCHs for an emergency call.

Updated: When an ESTABLISH_INDICATION message for an emergency call is received on SDCCH from the BTS.

See figure Basic call with counters.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S3 Definition updated in release:

Counter ID: 003022 Network element name: TCH EMERG CALL

Version: 3.0 NetAct name: TCH_EMERG_CALL

Description: Number of successful seizures of TCHs for an emergency call in FACCH call setup due to SDCCH congestion. If the FACCH call setup is turned off, the counter value is zero.

Updated: When an ESTABLISH_INDICATION message for an emergency call is received on TCH from the BTS.

See figure FACCH call setup due to SDCCH congestion

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

24 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.24 003023 / TCH MTC

2.25 003024 / TCH MOC

Related to feature:

BSS5290: FACCH Call Setup due to SDCCH Congestion

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S3 Definition updated in release:S5

Counter ID: 003023 Network element name: TCH MTC

Version: 3.0 NetAct name: TCH_MTC

Description: Number of successful seizures of TCHs for MTC in FACCH call setup due to SDCCH congestion. If the FACCH call setup is turned off, the counter value is zero.

Updated: When an ESTABLISH_INDICATION message with a paging response is received on TCH from the BTS.

See figure FACCH call setup due to SDCCH congestion

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature:

BSS5290: FACCH Call Setup due to SDCCH Congestion

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S3 Definition updated in release:S5

Counter ID: 003024 Network element name: TCH MOC

Version: 3.0 NetAct name: TCH_MOC

Description: Number of successful seizures of TCHs for MOC in FACCH call setup due to SDCCH congestion. If the FACCH call setup is turned off, the counter value is zero.

Updated: When an ESTABLISH_INDICATION message with a request for CM service is received on TCH from the BTS.

See figure FACCH call setup due to SDCCH congestion

DN9813745Issue 11-3

25

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.26 003025 / TCH CALL RE EST

2.27 003026 / SUCC TCH SMS EST

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature:

BSS5290: FACCH Call Setup due to SDCCH Congestion

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S3 Definition updated in release:S5

Counter ID: 003025 Network element name: TCH CALL RE EST

Version: 3.0 NetAct name: TCH_CALL_RE_EST

Description: Number of successful TCH seizures for call re-establishment attempts in FACCH call setup due to SDCCH congestion. If the FACCH call setup is turned off, the counter value is zero.

Updated: When an ESTABLISH_INDICATION message for a call re-establishment is received on TCH from the BTS. Note that this counter counts only the number of re-establisment attempts on TCH. Counter 057032 gives the number of TCH re-estab-lishment assignments.

See figure FACCH call setup due to SDCCH congestion

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature:

BSS5290: FACCH Call Setup due to SDCCH Congestion

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S3 Definition updated in release:S5

Counter ID: 003026 Network element name: SUCC TCH SMS EST

Version: 3.0 NetAct name: SUCC_TCH_SMS_EST

26 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.28 003027 / UNSUCC TCH SMS EST

Description: Number of SMSs successfully established on a TCH.

Updated: When an ESTABLISH_INDICATION message (mobile originating SMS) or an ESTABLISH_CONFIRM message (mobile terminating SMS) is received on TCH from the BTS.

See figures:- Mobile originating SMS on a TCH- Mobile terminating SMS on a TCH- Mobile originating SMS on FACCH- Mobile terminating SMS on FACCH

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S3 Definition updated in release:

Counter ID: 003027 Network element name: UNSUCC TCH SMS EST

Version: 3.0 NetAct name: UNSUCC_TCH_SMS_EST

Description: Number of unsuccessful establishments of SMSs on a TCH.

Updated: When establishment of SMS fails on TCH.

See figures:- Mobile originating unsuccessful SMS on a TCH- Mobile terminating unsuccessful SMS on a TCH- Mobile originating unsuccessful SMS on FACCH- Mobile terminating unsuccessful SMS on FACCH

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

DN9813745Issue 11-3

27

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.29 003028 / SUCC SDCCH SMS EST

2.30 003029 / UNSUCC SDCCH SMS EST

Used from release: S3 Definition updated in release:

Counter ID: 003028 Network element name: SUCC SDCCH SMS EST

Version: 3.0 NetAct name: SUCC_SDCCH_SMS_EST

Description: Number of SMSs successfully established on an SDCCH.

Updated: When an ESTABLISH_INDICATION message (mobile originating SMS) or an ESTABLISH_CONFIRM message (mobile terminating SMS) is received on SDCCH from the BTS.

See figures:- Mobile originating SMS on an SDCCH- Mobile terminating SMS on an SDCCH

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S3 Definition updated in release:

Counter ID: 003029 Network element name: UNSUCC SDCCH SMS EST

Version: 3.0 NetAct name: UNSUCC_SDCCH_SMS_EST

Description: Number of unsuccessful establishments of SMSs on an SDCCH.

Updated: When the establishment of an SMS fails on SDCCH.

See figures:- Mobile originating unsuccessful SMS on an SDCCH- Mobile terminating unsuccessful SMS on an SDCCH

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

28 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.31 003030 / GHOST CCCH RES

2.32 003031 / REJ SEIZ ATT DUE DIST

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S3 Definition updated in release:

Counter ID: 003030 Network element name: GHOST CCCH RES

Version: 3.0 NetAct name: GHOST_CCCH_RES

Description: Number of ghost reservations on a CCCH.

See also counter 003031.

Updated: When a ghost reservation is detected on a CCCH. This kind of random access can be caused, for example, by white noise or co-channel interference. Note that the ghosts triggering this counter have illegal establishment cause. Ghost accessess with legal establishment cause get on SDCCH and later fail typically causing the triggering of counter 0010075.

See figure Ghost reservation

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003031: REJ SEIZ ATT DUE DIST

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S3 Definition updated in release:

Counter ID: 003031 Network element name: REJ SEIZ ATT DUE DIST

Version: 3.0 NetAct name: REJ_SEIZ_ATT_DUE_DIST

Description: Number of seizure attempts rejected due to distance.

Counter 003030 is updated along with this counter.

DN9813745Issue 11-3

29

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.33 003032 / TRX IN EXT AREA

Updated: When random access is rejected by the BSC because of a too long distance between the MS and BTS. This kind of random access can be caused, for example, by white noise or co-channel interference.

See figure Ghost reservation

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003030: GHOST CCCH RES

Operability class:

Related to feature:

BSS5280: Distance Checking in Resource Allocation

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S5 Definition updated in release:

Counter ID: 003032 Network element name: TRX IN EXT AREA

Version: 3.1 NetAct name: TRX_TYPE

Description: Identification of a TRX.

0 = normal area1 = extended area2 = super-extended area

Updated:

Logical type: Variable Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature:

BSS21277: 105km Extended Cell CS

BSS6037: Extended Cell Range

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S6 Definition updated in release:S14

30 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.34 003033 / IMSI DETACH SDCCH

2.35 003034 / IMSI DETACH TCH

Counter ID: 003033 Network element name: IMSI DETACH SDCCH

Version: 3.0 NetAct name: IMSI_DETACH_SDCCH

Description: Number of successful seizures of SDCCHs for IMSI detach.

Updated: When an ESTABLISH_INDICATION message for an IMSI detach is received on SDCCH from the BTS.

See figure Basic call with counters

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature:

BSS7042: Measurement Improvements

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S7 Definition updated in release:

Counter ID: 003034 Network element name: IMSI DETACH TCH

Version: 3.0 NetAct name: IMSI_DETACH_TCH

Description: Number of successful seizures of TCHs for IMSI detach in FACCH call setup due to SDCCH congestion. If the FACCH call setup is turned off, then the counter value is zero.

Updated: When an ESTABLISH_INDICATION message for an IMSI detach is received on TCH from the BTS.

See figure FACCH call setup due to SDCCH congestion

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature:

BSS7042: Measurement Improvements

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

DN9813745Issue 11-3

31

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.36 003035 / MAX PAGING BUFFER CAPA

2.37 003036 / AVE PAGING BUFFER CAPA

Exceptions to related standard:

Used from release: S7 Definition updated in release:

Counter ID: 003035 Network element name: MAX PAGING BUFFER CAPA

Version: 3.0 NetAct name: MAX_PAGING_BUFFER_CAPA

Description: Maximum percent of paging buffer capacity. This counter indicates maximum paging buffer occupancy percentage during the reporting period. The range of this counter is 0-100% with 1% intervals.

Updated: When the value of the maximum paging buffer received in a CCCH_LOAD_INDICATION message exceeds the previous value of the paging buffer during a measurement period.

See figure CCCH load indication

Logical type: Max Trigger type: Event Sampling interval:

Unit: % Range: 0-100 Example values:

Dependencies with other counters:

Operability class:

Related to feature:

BSS7048: CCCH Improvements

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S7 Definition updated in release:

Counter ID: 003036 Network element name: AVE PAGING BUFFER CAPA

Version: 3.0 NetAct name: AVE_PAGING_BUFFER_CAPA_NUMER

32 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.38 003037 / RES ACC DENOMINATOR 5

Description: The sum of the average paging buffer occupancy percentages. Each time a CCCH load reporting period ends, the occupancy percentage is calculated and reported in a CCCH LOAD INDICATION message. The average is calculated with (100*N)/N(max)%, where N is the occupied buffer space and N(max) is the maximum buffer space during the CCCH load reporting period.

The CCCH load reporting period is the time between CCCH LOAD INDICATION message sendings. This counter stores the sum of the average paging buffer values received in CCCH LOAD INDICATION messages.

Counter 003037 is updated along with this counter.

Updated: When a CCCH LOAD INDICATION message is received from the BTS. The average paging buffer value is added to the previous value.

See figure CCCH load indication.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: % Range: Example values:

Dependencies with other counters:

003037: RES ACC DENOMINATOR 5

Operability class:

Related to feature:

BSS7048: CCCH Improvements

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S7 Definition updated in release:

Counter ID: 003037 Network element name: RES ACC DENOMINATOR 5

Version: 3.0 NetAct name: AVE_PAGING_BUFFER_CAPA_DENOM

Description: Denominator of the counter 003036 AVE PAGING BUFFER CAPA (always > 0).

Counter 003036 is updated along with this counter.

Updated: When a CCCH LOAD INDICATION message is received from the BTS and the average paging buffer occupancy percentage is reported in the message.

See figure CCCH load indication.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

DN9813745Issue 11-3

33

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.39 003038 / DELETE PAGING COMMAND

2.40 003039 / BCSU OVERLOAD LOWER LIMIT

Dependencies with other counters:

003036: AVE PAGING BUFFER CAPA

Operability class:

Related to feature:

BSS7048: CCCH Improvements

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S7 Definition updated in release:

Counter ID: 003038 Network element name: DELETE PAGING COMMAND

Version: 3.0 NetAct name: DELETE_PAGING_COMMAND

Description: Number of the delete paging commands. This counter indicates if some group-specific paging queue becomes so full that an additional paging command cannot be stored to the buffer. In such a case the paging command is deleted.

The message reports the total amount of such deleted paging commands during the reporting period.

Updated: When a CCCH_LOAD_INDICATION message is received from the BTS and the paging command is deleted.

See figure CCCH load indication

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature:

BSS7048: CCCH Improvements

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S7 Definition updated in release:

Counter ID: 003039 Network element name: BCSU OVERLOAD LOWER LIMIT

34 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.41 003040 / BCSU OVERLOAD UPPER LIMIT

Version: 3.0 NetAct name: BCSU_OVERLOAD_LOWER_LIMIT

Description: Number of refused calls, when BCSU overload lower limit occurs. When the overload lower limit occurs, all calls except emergency, MOC and MTC calls are refused.

Updated: When the call is refused due to BCSU overload lower limit. Each time a new CHANNEL_REQUIRED message comes from the BTS through the Abis interface, a software application in the BCSU checks the number of free message buffers in the unit. When the lower limit (more than 34 unhandled messages) is exceeded, the causes moc_data, location_update, other_cases and re_establishment will be omitted.

See figure Unsuccessful channel requests due to BCSU overload

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S7 Definition updated in release:

Counter ID: 003040 Network element name: BCSU OVERLOAD UPPER LIMIT

Version: 3.0 NetAct name: BCSU_OVERLOAD_UPPER_LIMIT

Description: Number of refused calls, when BCSU overload upper limit occurs. When the overload upper limit occurs, all calls are refused.

Updated: When the call is refused due to BCSU overload upper limit. Each time a new CHANNEL_REQUIRED message comes from the BTS through the Abis interface, a software application in the BCSU checks the number of free message buffers in the unit. When the upper limit (more than 53 unhandled messages) is exceeded, no causes will trigger channel reservation in the BSC.

See figure Unsuccessful channel requests due to BCSU overload

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

DN9813745Issue 11-3

35

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.42 003041 / BCSU OVERLOAD DELETED RACH

2.43 003042 / TRX DIAGNOSTICS

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S7 Definition updated in release:

Counter ID: 003041 Network element name: BCSU OVERLOAD DELETED RACH

Version: 3.0 NetAct name: BCSU_OVERLOAD_DELETED_RACH

Description: Number of deleted RACHs on a CCCH when the RACH load is too high and MCMU is protected against overload.

Updated: When new RACH commands arrive to the CCCH but the maximum number of simultaneous RACH requests have already been sent to the MCMU and therefore there is no free space for any new RACH requests and the commands are deleted. The maximum number of simultaneous RACH requests is dynamically changed at BCSU level according to the load of the MCMU. If there are more requests, the RACHs are deleted and this counter is triggered.

See figure Unsuccessful channel requests due to BCSU overload

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S7 Definition updated in release:S11.5

Counter ID: 003042 Network element name: TRX DIAGNOSTICS

Version: 3.0 NetAct name: TRX_DIAGNOSTIC

Description: Number of the running times of TRX internal diagnostics.

Updated: When TRX internal diagnostics is started. The base station has requested the blocking of the TRX for diagnostics.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

36 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.44 003043 / TRX DIAGNOSTICS FAULT

2.45 003044 / SUCC SEIZ SUPPLEM SERV

Dependencies with other counters:

Operability class:

Related to feature:

BSS8143: Runtime diagnostics and BTS alarms

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S8 Definition updated in release:

Counter ID: 003043 Network element name: TRX DIAGNOSTICS FAULT

Version: 3.0 NetAct name: TRX_DIAGNOSTIC_FAULT

Description: Number of times that the TRX internal diagnostics has detected a fault.

Updated: When diagnostics is stopped after fault detection. The BTS has sent a message informing that the diagnostics has been stopped and that a fault has been detected.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature:

BSS8143: Runtime diagnostics and BTS alarms

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S8 Definition updated in release:

Counter ID: 003044 Network element name: SUCC SEIZ SUPPLEM SERV

Version: 3.0 NetAct name: SUCC_SEIZ_SUPPLEM_SERV

Description: Number of successful seizures of SDCCHs for supplementary service.

Updated: When an ESTABLISH_INDICATION message with CM service request and service type supplementary service is received on SDCCH from the BTS.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

DN9813745Issue 11-3

37

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.46 003045 / TCH SUPPLEM SERV

2.47 003046 / AVE PCH GB LOAD ON CCCH

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S9 Definition updated in release:

Counter ID: 003045 Network element name: TCH SUPPLEM SERV

Version: 3.0 NetAct name: TCH_SUPPLEM_SERV

Description: Number of successful seizures of TCHs for supplementary service in FACCH call setup due to SDCCH congestion. If FACCH call setup is turned off, the counter value is zero.

Updated: When an ESTABLISH_INDICATION message with CM service request and service type supplementary service is received on TCH from the BTS.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S9 Definition updated in release:

Counter ID: 003046 Network element name: AVE PCH GB LOAD ON CCCH

Version: 3.0 NetAct name: AVE_PCH_GB_LOAD_ON_CCCH_SUM

Description: Average paging buffer space on Gb-interface. The counter indicates the remaining space for paging commands (CS, PS) and DRX Access Grant. Smaller value means greater load on the PCH.

Counter 003047 is updated along with this counter.

38 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.48 003047 / RES ACC DENOMINATOR 6

Updated: When the value of the PCH Gb load is received in a CCCH_LOAD_IND message from the BTS during the measurement period. The new value of the PCH Gb load is added to the previous value, and the number of events is increased by one.

When CCCH_LOAD_IND message is received by BSC and GPRS support is config-ured on CCCH. See figure CCCH load indication if GPRS is activated in BTS and other conditions are valid.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003047: RES ACC DENOMINATOR 6

Operability class:

Related to feature:

BSS09006: General Packet Radio Service (GPRS)

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S9 Definition updated in release:

Counter ID: 003047 Network element name: RES ACC DENOMINATOR 6

Version: 3.0 NetAct name: AVE_PCH_GB_LOAD_ON_CCCH_DEN

Description: Denominator of average PCH Gb load on CCCH.

Counter 003046 is updated along with this counter.

Updated: See figure CCCH load indication if GPRS is activated in BTS and other con-ditions are valid

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003046: AVE PCH GB LOAD ON CCCH

Operability class:

Related to feature:

BSS09006: General Packet Radio Service (GPRS)

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S9 Definition updated in release:

DN9813745Issue 11-3

39

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.49 003048 / AVE PAGING GB BUF

2.50 003049 / RES ACC DENOMINATOR 7

Counter ID: 003048 Network element name: AVE PAGING GB BUF

Version: 3.0 NetAct name: AVE_PAGING_GB_BUF_SUM

Description: Average buffer occupancy percentage.

It is used to carry information on the load of the PCH associated with this CCCH timeslot. This information reports the paging buffer occupancy percentages within the buffer area of approximately 15 seconds, in case the GPRS support is configured onto CCCH. The range of this parameter is 0...100% with 1% intervals. The occupancy percentage (occupied buffer space vs. maximum space) of paging buffer is calculated every fourth 51-multiframe. An average is calculated from these values and reported in CCCH_LOAD_IND message.

Counter 003049 is updated along with this counter.

Updated: When the value of the average paging Gb buffer load is received in a CCCH_LOAD_IND message from the BTS during measurement period. The new value of the average paging Gb buffer load is added to the previous value, and the number of events is increased by one.

When CCCH_LOAD_IND message is received by BSC and GPRS support is config-ured on CCCH. See figure CCCH load indication if GPRS is activated in BTS and other conditions are valid

Logical type: Sum Trigger type: Event Sampling interval:

Unit: % Range: 0 - 100 Example values:

Dependencies with other counters:

003049: RES ACC DENOMINATOR 7

Operability class:

Related to feature:

BSS09006: General Packet Radio Service (GPRS)

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S9 Definition updated in release:

Counter ID: 003049 Network element name: RES ACC DENOMINATOR 7

Version: 3.0 NetAct name: AVE_PAGING_GB_BUF_DEN

Description: Denominator of average buffer occupancy percentage.

Counter 003048 is updated along with this counter.

40 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.51 003050 / MAX PAGING GB BUF

Updated: See figure CCCH load indication if GPRS is activated in BTS and other con-ditions are valid

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003048: AVE PAGING GB BUF

Operability class:

Related to feature:

BSS09006: General Packet Radio Service (GPRS)

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S9 Definition updated in release:

Counter ID: 003050 Network element name: MAX PAGING GB BUF

Version: 3.0 NetAct name: MAX_PAGING_GB_BUF

Description: Maximum buffer occupancy percentage.

It is used to carry information on the load of the PCH associated with this CCCH timeslot. It is the peak value of all values which are calculated every fourth 51-multi-frame during the concerned CCCH_LOAD_IND reporting period. The range of this parameter is 0...100% with 1% intervals.

Updated: When the value of the maximum paging buffer received in a CCCH_LOAD_INDICATION message exceeds the previous value of the paging buffer during the measurement period.

When CCCH_LOAD_IND message is received by BSC and GPRS support is config-ured on CCCH. See figure CCCH load indication if GPRS is activated in BTS and other conditions are valid

Logical type: Max Trigger type: Event Sampling interval:

Unit: % Range: 0 - 100 Example values:

Dependencies with other counters:

Operability class:

Related to feature:

BSS09006: General Packet Radio Service (GPRS)

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

DN9813745Issue 11-3

41

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.52 003051 / AVE PAGING LOAD AIR

2.53 003052 / RES ACC DENOMINATOR 8

Used from release: S9 Definition updated in release:

Counter ID: 003051 Network element name: AVE PAGING LOAD AIR

Version: 3.0 NetAct name: AVE_PAGING_LOAD_AIR_SUM

Description: Average paging load on CCCH indicated by radio block occupancy for paging messages.

Radio Block Occupancy carries information on the Radio interface load in percents of the associated CCCH timeslot. The radio block occupancy percentage for AGCH messages requiring DRX (occupied radio blocks vs. all radio blocks during reporting period) is calculated and reported in CCCH_LOAD_ IND message.

Counter 003052 is updated along with this counter.

Updated: When a CCCH_LOAD_INDICATION message is received from the BTS. The average paging load value is added to the previous value and the number of events is increased by one.

When CCCH_LOAD_IND message is received by BSC and phase 2 BTS or newer is supported. See figure CCCH load indication if GPRS is activated in BTS and other conditions are valid

Logical type: Sum Trigger type: Event Sampling interval:

Unit: % Range: 0 - 100 Example values:

Dependencies with other counters:

003052: RES ACC DENOMINATOR 8

Operability class:

Related to feature:

BSS09006: General Packet Radio Service (GPRS)

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S9 Definition updated in release:

Counter ID: 003052 Network element name: RES ACC DENOMINATOR 8

Version: 3.0 NetAct name: AVE_PAGING_LOAD_AIR_DEN

Description: Denominator of average radio interference CCCH load radio block occu-pancy paging.

Counter 003051 is updated along with this counter.

42 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.54 003053 / AVE DRX AGCH LOAD AIR

Updated: See figure CCCH load indication if GPRS is activated in BTS and other con-ditions are valid

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003051: AVE PAGING LOAD AIR

Operability class:

Related to feature:

BSS09006: General Packet Radio Service (GPRS)

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S9 Definition updated in release:

Counter ID: 003053 Network element name: AVE DRX AGCH LOAD AIR

Version: 3.0 NetAct name: AVE_DRX_AGCH_LOAD_AIR_SUM

Description: Average radio interference CCCH load radio block occupancy DRX AGCH.

It is used to carry information on the Radio interface load of the associated CCCH timeslot. The range of this parameter is 0...100% with 1% intervals. The radio block occupancy percentage for AGCH messages requiring DRX (occupied radio blocks vs. all radio blocks during reporting period) is calculated and reported in CCCH_LOAD_ IND message.

Counter 003054 is updated along with this counter.

Updated: When a CCCH_LOAD_INDICATION message is received from the BTS. The average DRX AGCH LOAD AIR value is added to the previous value and the number of events is increased by one.

When CCCH_LOAD_IND message is received by BSC and phase 2 BTS or newer is supported. See figure CCCH load indication if GPRS is activated in BTS and other conditions are valid

Logical type: Sum Trigger type: Event Sampling interval:

Unit: % Range: 0 - 100 Example values:

Dependencies with other counters:

003054: RES ACC DENOMINATOR 9

Operability class:

DN9813745Issue 11-3

43

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.55 003054 / RES ACC DENOMINATOR 9

2.56 003055 / AVE NON DRX AGCH LOAD AIR

Related to feature:

BSS09006: General Packet Radio Service (GPRS)

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S9 Definition updated in release:

Counter ID: 003054 Network element name: RES ACC DENOMINATOR 9

Version: 3.0 NetAct name: AVE_DRX_AGCH_LOAD_AIR_DEN

Description: Denominator of average radio interference CCCH load radio block occu-pancy DRX AGCH.

Counter 003053 is updated along with this counter.

Updated: See figure CCCH load indication if GPRS is activated in BTS and other con-ditions are valid

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003053: AVE DRX AGCH LOAD AIR

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S9 Definition updated in release:

Counter ID: 003055 Network element name: AVE NON DRX AGCH LOAD AIR

Version: 3.0 NetAct name: AVE_NON_DRX_AGCH_LOAD_AIR_SUM

44 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.57 003056 / RES ACC DENOMINATOR 10

Description: Average radio interference CCCH load radio block occupancy NON-DRX AGCH.

It is used to carry information on the Radio interface load of the associated CCCH timeslot. The range of this parameter is 0...100% with 1% intervals. The radio block occupancy percentage for AGCH messages not requiring DRX (occupied radio blocks vs. all radio blocks during reporting period) is calculated and reported in CCCH_LOAD_ IND message.

Counter 003056 is updated along with this counter.

Updated: When a CCCH_LOAD_INDICATION message is received from the BTS. The average NON DRX AGCH LOAD AIR value is added to the previous value and the number of events is increased by one.

When CCCH_LOAD_IND message is received by BSC and phase 2 BTS or the newer is supported. See figure CCCH load indication if GPRS is activated in BTS and other conditions are valid

Logical type: Sum Trigger type: Event Sampling interval:

Unit: % Range: 0 - 100 Example values:

Dependencies with other counters:

003056: RES ACC DENOMINATOR 10

Operability class:

Related to feature:

BSS09006: General Packet Radio Service (GPRS)

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S9 Definition updated in release:

Counter ID: 003056 Network element name: RES ACC DENOMINATOR 10

Version: 3.0 NetAct name: AVE_NON_DRX_AGCH_LOAD_AIR_DEN

Description: Denominator of average radio interference CCCH load radio block occu-pancy NON-DRX AGCH.

Counter 003055 is updated along with this counter.

Updated: See figure CCCH load indication if GPRS is activated in BTS and other con-ditions are valid

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

DN9813745Issue 11-3

45

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.58 003057 / PS PAGING MSG SENT

2.59 003058 / CS PAGING MSG SENT

Dependencies with other counters:

003055: AVE NON DRX AGCH LOAD AIR

Operability class:

Related to feature:

BSS09006: General Packet Radio Service (GPRS)

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S9 Definition updated in release:

Counter ID: 003057 Network element name: PS PAGING MSG SENT

Version: 3.0 NetAct name: PS_PAGING_MSG_SENT

Description: This message is sent from the BSC/PCU to the BTS to request PS paging of a GPRS MS.

Updated: When a PS-PAGING COMMAND message is sent to the BTS. The MS needs to be paged only when it is in MM-idle state. A GPRS paging message is sent only to cells that support GPRS services.

When a PS-PAGING COMMAND message is sent from the BSC to the BTS. See figure PS paging in GPRS

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature:

BSS09006: General Packet Radio Service (GPRS)

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S9 Definition updated in release:

Counter ID: 003058 Network element name: CS PAGING MSG SENT

Version: 3.0 NetAct name: CS_PAGING_MSG_SENT

Description: This message is sent from BSC/PCU to BTS to request CS paging of a GPRS MS.

46 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.60 003059 / CALL ASSIGN AFTER SMS

2.61 003060 / SPARE003060

Updated: When a CS-PAGING COMMAND is sent to the BTS.

When a CS-PAGING COMMAND message is sent from BSC to the BTS. See figure CS Paging in GPRS

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature:

BSS09006: General Packet Radio Service (GPRS)

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S9 Definition updated in release:

Counter ID: 003059 Network element name: CALL ASSIGN AFTER SMS

Version: 3.0 NetAct name: CALL_ASSIGN_AFTER_SMS

Description: Number of calls started directly after an SMS on the already reserved SDCCH.

Updated: When an ASSIGNMENT REQUEST message is received directly after a successful SMS on SDCCH from the MSC.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S10.5 Definition updated in release:

Counter ID: 003060 Network element name: SPARE003060

Version: 3.0 NetAct name: SPARE003060

Description: Spare

DN9813745Issue 11-3

47

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.62 003061 / SPARE003061

2.63 003062 / SPARE003062

Updated:

Logical type: Trigger type: Sampling interval:

Unit: Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S10.5 Definition updated in release:

Counter ID: 003061 Network element name: SPARE003061

Version: 3.0 NetAct name: SPARE003061

Description: Spare

Updated:

Logical type: Trigger type: Sampling interval:

Unit: Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S10.5 Definition updated in release:

Counter ID: 003062 Network element name: SPARE003062

Version: 3.0 NetAct name: SPARE003062

Description: Spare

Updated:

Logical type: Trigger type: Sampling interval:

Unit: Range: Example values:

Dependencies with other counters:

Operability class:

48 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d805807efbed

Counters of Resource Access Measurement

2.64 003063 / SPARE003063

2.65 003064 / SUCC MO SMS SDCCH

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S10.5 Definition updated in release:

Counter ID: 003063 Network element name: SPARE003063

Version: 3.0 NetAct name: SPARE003063

Description: Spare

Updated:

Logical type: Trigger type: Sampling interval:

Unit: Range: Example values:

Dependencies with other counters:

Operability class:

Related to feature: Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S10.5 Definition updated in release:

Counter ID: 003064 Network element name: SUCC MO SMS SDCCH

Version: 3.0 NetAct name: SUCC_MO_SMS_SDCCH

Description: Number of mobile originated SMSs successfully established on an SDCCH.

Counter 003028 is updated together with this counter.

Updated: At the same time as counter 003028 (SUCC SDCCH SMS EST) but only when ESTABLISH INDICATION message for a mobile originated SMS is received on SDCCH from the BTS.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003028: SUCC SDCCH SMS EST

Operability class:

DN9813745Issue 11-3

49

3 Resource Access Measurement Counters of Resource Access Measurement

Id:0900d805807efbed

2.66 003065 / UNSUCC MO SMS SDCCH

Related to feature:

BSS115168: CS Statistics Improvements

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S11.5 Definition updated in release:

Counter ID: 003065 Network element name: UNSUCC MO SMS SDCCH

Version: 3.0 NetAct name: UNSUCC_MO_SMS_SDCCH

Description: Number of mobile originated SMSs unsuccessfully established on an SDCCH.

Counter 003029 is updated together with this counter.

Updated: At the same time as counter 003029 (UNSUCC SDCCH SMS EST) but only when ESTABLISH INDICATION message for a mobile originated SMS is received on SDCCH from the BTS.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

003029: UNSUCC SDCCH SMS EST

Operability class:

Related to feature:

BSS115168: CS Statistics Improvements

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S11.5 Definition updated in release:

50 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d8058061b26b

Signalling charts of Resource Access Measurement

3 Signalling charts of Resource Access Mea-surementThe following figures show the signalling charts of Resource Access Measurement:

Figure 1 Basic call without counters.

BSC:MS: BTS: MSC:

PagingPaging commandPaging request

Channel requestChannel required

Channel activation

Immediate assign

SetupSetup

Call proceeding Call proceeding

Assignment requestPhysical context request

Physical context confirm

Channel activation

Channel activation ack

Assignment command

Ua

Sabm Establish indication

Ua

Assignment complete Assignment complete

Rf channel release

Rf channel release ack

Identification requestIdentification request

Identification response Identification response

Encryption command

Paging part

Radio access part on CCCH

Channel activation ack

Immediate assign command

Sabm Establish indication Paging response

Authentication requestAuthentification request

Authentification response

SDCCH signalling part

DDCH establishment part

TCH seized, FACCH signalling part

Ciphering mode command

Ciphering mode complete

Authentication response

Ciphering mode command

Ciphering mode complete

DN9813745Issue 11-3

51

3 Resource Access Measurement Signalling charts of Resource Access Measurement

Id:0900d8058061b26b

Figure 2 Basic call without counters (cont.).

Alert Alert

Connect Connect

Connect ackConnect ack

Release complete

Clear command

Clear complete

Channel release

Deactivate SACCH

Ua

Release indication

Rf channel release

Rf channel release ack

Disconnect Disconnect

ReleaseRelease

Release complete

BSC:MS: BTS: MSC:

Disc

Conversation phase

Release by MS

52 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d8058061b26b

Signalling charts of Resource Access Measurement

Figure 3 Basic call with counters.

BTS: MSC:MS: BSC:

PagingPaging command

Paging request

Channel request

Channel required

Channel activation

Channel activation ack

Immediate assign

SabmEstablish indication

Paging responseUa

Paging part

Paging messages sent to BTS003000

Radio access part on CCCH

Channel request messagesreceived from BTS

003004

Immediate assign command

Immediate assignment messagesent to BTS

003001

DDCH establishment part

SDCCH signalling part

TCH seized, FACCH signalling part

Conversation phase

Release by MS

Success seizure for MTC003012

or Success seizure for MOC003013

or SDCCH location update003019

or SDCCH call re-establishment003020

or SDCCH emergency call003021

or IMSI detach SDCCH003033

DN9813745Issue 11-3

53

3 Resource Access Measurement Signalling charts of Resource Access Measurement

Id:0900d8058061b26b

Figure 4 FACCH call setup due to SDCCH congestion.

BTS:MS: BSC: MSC:

Sabm

Establish indication

Paging response

Ua

Radio access part on CCCH

Paging part

DDCH establishment part

TCH signalling part

Conversation phase

Release by MS

TCH emergency call003022

orTCH MTC

003023or

TCH MOC003024

orTCH call re-establishm.

003025or

IMSI detach TCH003034

54 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d8058061b26b

Signalling charts of Resource Access Measurement

Figure 5 Ghost reservation.

Counter 003031 is updated if distance verifying is activated in the resource allocation feature and the channel request is rejected due to the distance between the MS and BTS.

Ghost

Channel required

BSC:MS: MSC:BTS:

Radio access part on CCCH

Paging part

Rej seiz att due dist

003031

GHOST CCCH reservation

003030

Channel request messages

received from BTS

003004

DN9813745Issue 11-3

55

3 Resource Access Measurement Signalling charts of Resource Access Measurement

Id:0900d8058061b26b

Figure 6 Busy AGCH-channel.

Figure 7 Unsuccessful channel request.

Channel required

Channel activation

Channel request

Delete indication

MS: BSC: MSC:BTS:

Radio access part on CCCH

Paging part

Channel activation ack

Immediate assign command

Immediate assignmentmessages sent to BTS

003001

Delete indication messagesreceived from BTS

003005

Channel request messagesreceived from BTS

003004

Channel required

Channel request

BSC:MS: MSC:BTS:

Radio access part on CCCH

Paging part

Immediate assignment reject

Channel request messagesreceived from BTS

003004

Immediate assignment rejectmessages sent to BTS

003002

56 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d8058061b26b

Signalling charts of Resource Access Measurement

Figure 8 SMS broadcast.

Figure 9 Mobile originating SMS on a TCH.

BSC:MS: MSC:BTS:

SMS broadcast request

SMS broadcast request

SMS broadcast request

SMS broadcast request

SMS CB request messagessent to the BTS

003003

Cp data

Cm serv req

Ua (SAPI = 3)

Sabm (SAPI = 3)

Establish indication

Cp data

Cp ack Cp ack

Cp data Cp data

Cp ackCp ack

Cm serv req

Cm serv ackCm serv ack

BSC:MS: MSC:BTS:

Active call

Successful TCH SMS003026

Active call continuous

DN9813745Issue 11-3

57

3 Resource Access Measurement Signalling charts of Resource Access Measurement

Id:0900d8058061b26b

Figure 10 Mobile terminating SMS on a TCH.

Figure 11 Mobile originating SMS on FACCH.

Cp data

Establish request

Sabm (SAPI = 3)

Ua (SAPI = 3)

Establish confirm

Cp data

Cp ack Cp ack

Cp data Cp data

Cp ackCp ack

BTS: MSC:MS: BSC:

Active call

Active call continuous

Successful TCH SMS003026

MS starts SMS by sending SABM with SAPI = 3

SMS release

Cp ack

Cp ack

Cp data

Cp data

Cp ack

Cp ack

Cp data

Establish indication

Sabm (SAPI = 3)

FACCH call setup

Ua (SAPI = 3)

Instead of sending SETUP -message,

Cp data

BSC:MS: MSC:BTS:

Successful TCH SMS003026

58 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d8058061b26b

Signalling charts of Resource Access Measurement

Figure 12 Mobile terminating SMS on FACCH.

Establish request

MSC starts SMS by sending CP DATA -message

SMS release

Cp ack

Cp ack

Cp data

Cp data

Cp ack

Cp ack

Cp data

Establish confirm

Ua (SAPI = 3)

FACCH call setup

Sabm (SAPI = 3)

Instead of sending SETUP -message,

Cp data

BTS: MSC:MS: BSC:

Successful TCH SMS003026

DN9813745Issue 11-3

59

3 Resource Access Measurement Signalling charts of Resource Access Measurement

Id:0900d8058061b26b

Figure 13 Mobile originating SMS on an SDCCH.

Cp data

Ua (SAPI = 3)

Sabm (SAPI = 3)

Establish indication

Cp data

Cp ack Cp ack

Cp data Cp data

Cp ackCp ack

BTS: MSC:MS: BSC:

Instead of sending SETUP -message,

Connection is set up as in normal MOC

SMS release

MS starts SMS by sending SABM with SAPI = 3

Successful SDCCH SMS003028

60 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d8058061b26b

Signalling charts of Resource Access Measurement

Figure 14 Mobile terminating SMS on an SDCCH.

Cp data

Sabm (SAPI = 3)

Ua (SAPI = 3)

Establish confirm

Cp data

Cp ack Cp ack

Cp data Cp data

Cp ackCp ack

Establish request

BSC:MS: MSC:BTS:

Instead of sending SETUP -message,

Connection is set up as in normal MTC

SMS release

MSC starts SMS by sending CP DATA -message

Successful SDCCH SMS003028

DN9813745Issue 11-3

61

3 Resource Access Measurement Signalling charts of Resource Access Measurement

Id:0900d8058061b26b

Figure 15 Mobile originating unsuccessful SMS on a TCH.

In the figure a failure can occur between the first and last position, causing counter 3027 to be updated immediately. Signalling between the first and last position can be partly missing depending on where the failure takes place. Possible situations are: ERROR_INDICATION, RELEASE_INDICATION or CONNECTION_ FAILURE message during an SMS, and corrupted ESTABLISH_ INDICATION message.

Cm serv ack Cm serv ack

Cm serv req

Cp ack

Cp ack

Cp data

Cp data

Cp ack

Cp ack

Cp data

Establish indication

Sabm (SAPI = 3)

Ua (SAPI = 3)

Cm serv req

Cp data

BTS: MSC:MS: BSC:

Active call

First position

Last position

Active call continuous

62 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d8058061b26b

Signalling charts of Resource Access Measurement

Figure 16 Mobile terminating unsuccessful SMS on a TCH.

In the figure a failure can occur between the first and last position, causing counter 3027 to be updated immediately. Signalling between the first and last position can be partly missing depending on where the failure takes place. Possible situations are: ERROR_INDICATION, RELEASE_INDICATION or CONNECTION_ FAILURE message during an SMS, and corrupted ESTABLISH_ INDICATION message.

Cp data

Establish request

Sabm (SAPI = 3)

Ua (SAPI = 3)

Establish confirm

Cp data

Cp ack Cp ack

Cp data Cp data

Cp ackCp ack

BTS: MSC:MS: BSC:

Last position

First position

Active call

Active call continuous

DN9813745Issue 11-3

63

3 Resource Access Measurement Signalling charts of Resource Access Measurement

Id:0900d8058061b26b

Figure 17 Mobile originating unsuccessful SMS on FACCH.

In the figure a failure can occur between the first and last position, causing counter 3027 to be updated immediately. Signalling between the first and last position can be partly missing depending on where the failure takes place. Possible situations are: ERROR_INDICATION, RELEASE_INDICATION or CONNECTION_ FAILURE message during an SMS, and corrupted ESTABLISH_ INDICATION message.

Cp data

Ua (SAPI = 3)

Sabm (SAPI = 3)

Establish indication

Cp data

Cp ack Cp ack

Cp data Cp data

Cp ackCp ack

BTS: MSC:MS: BSC:

SMS release

Instead of sending SETUP -message,

FACCH call setup

MS starts SMS by sending SABM with SAPI = 3

Unsuccessful TCH SMS003027

64 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d8058061b26b

Signalling charts of Resource Access Measurement

Figure 18 Mobile terminating unsuccessful SMS on FACCH.

In the figure a failure can occur between the first and last position, causing counter 3027 to be updated immediately. Signalling between the first and last position can be partly missing depending on where the failure happens. Possible situations are: ERROR_INDICATION, RELEASE_INDICATION or CONNECTION_ FAILURE message during an SMS, and corrupted ESTABLISH_ INDICATION message.

MS: BTS: BSC: MSC:

FACCH call setup

Instead of sending SETUP -message,

MSC starts SMS by sending CP DATA -message

Cp data

Establish request

First position

Sabm (SAPI = 3)

Ua (SAPI = 3)

Establish confirm

Last position

SMS release

DN9813745Issue 11-3

65

3 Resource Access Measurement Signalling charts of Resource Access Measurement

Id:0900d8058061b26b

Figure 19 Mobile originating unsuccessful SMS on an SDCCH.

Message data corrupted in the ESTABLISH_INDICATION message.

Figure 20 Mobile terminating unsuccessful SMS on an SDCCH.

Cp data

Ua (SAPI = 3)

Sabm (SAPI = 3)

Establish indication

Cp data

Cp ack

Cp ack

Cp data

Cp data

Cp ack

Cp ack

BTS: MSC:MS: BSC:

SMS release

Instead of sending SETUP -message,

Connection is set up as in normal MOC

MS starts SMS by sending SABM with SAPI = 3

Unsuccessful SDCCH SMS003029

Cp data

Establish request

Sabm (SAPI = 3)

Ua (SAPI = 3)

Establish confirm

MS: BTS: BSC: MSC:

Connection is set up as in normal MTC

Instead of sending SETUP -message,

MSC starts SMS by sending CP DATA -message

SMS release

First position

Last position

66 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d8058061b26b

Signalling charts of Resource Access Measurement

In the figure a failure can occur between the first and last position, causing counter 3029 to be updated immediately. Signalling between the first and last position can be partly missing depending on where the failure takes place. Such situations can be caused by timer expiries while waiting for ESTABLISH_CONFIRM message, an ERROR_INDICATION or RELEASE_INDICATION message that is received instead of an ESTABLISH_CONFIRM message, or a corrupted ESTABLISH_CONFIRM message.

Figure 21 CCCH load indication.

Counters 003035, 003036, 003037 and 003038 can be updated only with phase 2 BTS or newer versions. Counters 003051-003056 can be updated if the BTS version is of phase 2.

CCCH load indication

MS: BTS: BSC: MSC:

Paging part

Radio access part on CCCH

Ave nbr of RACH slots on CCCH003006

Denom of ave RACH slot number003007

Average PCH load on a CCCH003008

Denom of ave PCH load on CCCH003009

Peak value of number of busyRACHs on CCCH

003010

Ave nbr of busy RACHs on CCCH003014

Denom of ave nbr of busy RACHs003015

Nbr of ave RACH acc on CCCH003016

Denom of count of ave RACH acc003017

Min size of paging buffer on CCCH003018

Number of max paging buffer capa003035

Average paging buffer capacity003036

Denom of count of ave paging buffer003037

Number of deleted paging command003038

DN9813745Issue 11-3

67

3 Resource Access Measurement Signalling charts of Resource Access Measurement

Id:0900d8058061b26b

g Counter 003008 contains paging load information when paging comes through the Gb-interface and the GPRS is disabled in BTS, even if the BTS level is GPRS PH 1.

Figure 22 CCCH Load Indication if GPRS is activated in BTS and other conditions are valid.

Counters 003006-003010, 003014-003018 and 003035-003038 can also be updated.

MS: BTS: BSC: MSC:

Paging part

Radio access part on CCCH

CCCH load indication

Ave PCH Gb load on CCCH003046

Denom of ave DRX AGCHload air003054

Ave non DRX AGCH load air003055

Denom of ave non DRXAGCH load air

003056

Denom of ave PCH Gb loadon CCCH003047

Ave DRX AGCH load air003053

Ave paging Gb buffer003048

Denom of ave paging Gbbuffer

003049

Maximum paging Gb buffer003050

Ave paging load air003051

Denom of ave paging load air003052

68 DN9813745Issue 11-3

3 Resource Access Measurement

Id:0900d8058061b26b

Signalling charts of Resource Access Measurement

Figure 23 Unsuccessful channel requests because of BCSU overload.

Figure 24 PS Paging in GPRS

Figure 25 CS Paging in GPRS.

g If the GPRS level is GPRS PH1 but the GPRS is disabled in BTS, a normal paging command message is sent to the BTS.

Channel request

Channel required

MS: BTS: BSC: MSC:

Paging part

Radio access part on CCCH

Channel req msg received from BTS003004

BCSU overload lower limit003039

orBCSU overload upper limit

003040

BCSU overload deleted RACH003041

Paging command PS Paging

MS: BTS: BSC: SGSN:

Paging part

Ps paging msg sent003057

MS: BTS: BSC: SGSN: MSC:

Paging part

CS PagingCS PagingPaging command

Cs paging msg sent003058

DN9813745Issue 11-3

69

3 Resource Access Measurement Signalling charts of Resource Access Measurement

Id:0900d8058061b26b

Related topics3 Resource Access Measurement

Counters of Resource Access Measurement