Resume Shantanu S Joshi 1

8/8/2019 Resume Shantanu S Joshi 1

1/4

Resume

Shantanu Sudhir Joshi

Flat No.4, Santoor Building, Email: [email protected]

Plot No. 17-18-19, Sopan Baug, [email protected], Pune-411021 Contact No.: +91-9561426653

India

Nationality: Indian Date of Birth: 5th September 1984

Educational Qualifications

Master of Technology in Civil Engineering(Specialization- Structural Engineering)

Indian Institute of Technology Kanpur, Kanpur (India)

Year of completion: August 2009Cumulative Performance Index (CPI): 9.48/10

Bachelor of Engineering in Civil EngineeringUniversity of Pune, Pune (India)

Institute: Maharashtra Institute of Technology, Pune.

Year of completion: June 2006

Final Year Percentage: 69.53

Average Percentage of Four Years: 65.69

Higher Secondary School Examination CertificateAwarded by Maharashtra State Board of Secondary and Higher Secondary

Education, Pune (India).

Year of passing: 2002

Subjects: English, Mathematics & Statistics, Physics, Chemistry, Electronics.

Percentage: 88.33

Secondary School Examination CertificateAwarded by Maharashtra State Board of Secondary and Higher Secondary

Education, Pune (India).

Year of passing: 2000

Subjects: Marathi, Sanskrit, English, Mathematics, Science, Social Sciences.

Percentage: 86.00

Areas of Interest

Finite Element Modelling Earthquake Engineering

Reinforced Concrete Design Structural Dynamics


2/4

Work Experience

Organisation (From 1-Feb- 2010 to till date): MWH Global, Pune, India.Designation: Structural Engineer

Projects:

1. Title: Evanston City buried pump stationDetails: Design of Base slab, top cover slab and precast wall-base slab connection

Design Codes: ACI 350-06, ACI 318-02, ACI 360-06

Analysis Tools: STAAD Pro

2. Title: City of Las Vegas- Pump stationDetails: Design of Mat foundation supported on piers for the sludge blending

tank, design of mat foundation supported on piers for the pump station building

Design Codes: ACI 350-06, ASCE 7-05, ACI 350.3-06

Analysis Tools: STAAD Pro, MathCad

3. Title: South Baton Rouge WWTPDetails: Wind load analysis of Lab building and Administration building, Designof Lab building (CMU wall structure)

Design Codes: ASCE 7-05, ACI 350-06

Analysis Tools: STAAD Pro, MathCad

4. Title: Nampa Digester RetrofitDetails: Wall capacity assessment of 50 yrs old digester tank to check if it can

support additional wall load. This additional load was arising due to

replacement of existing metal roof by a new concrete slab roof.


Analysis Tool: STAAD Pro, CSI Col

5.

Title: Lake Kennedy canal pump stationDetails: Design of Pump-Chemical-Electrical building (CMU Wall Structure)


Analysis Tools: MathCad

6. Conducted a training on Introduction to ABAQUS for structural design team atMWH

Professional Trainings

Autodesk- Revit Structure 2010: 4-days in-house training conducted by Mr. EdHannibas of Autodesk (USA), organised by MWH Global Pune, India in Apr 2010.

ABAQUS- 3-days training at IIT Kharagpur by Dr. Arghya Deb- concrete modelling,soil-structure interaction, contact simulation-18th June to 20thJune 2010.


3/4

Software and Programming Languages

MATLAB ABAQUS SAP 2000 Nonlinear

Auto-CAD STAAD Pro MathCAD

Courses Credited

Postgraduate:

Engineering Mechanics Structural Dynamics Finite Element Methods in

Engineering Mechanics

Earthquake Analysis and Designof Structures

Experimental Methods inStructural Engineering

Engineering Mathematics

Undergraduate:

Advanced Analysis & Design ofStructures

Matrix Methods of Analysis Pre-stressed Concrete Design Reinforced Concrete Design Steel Design Structural Analysis Engineering Mechanics

Paleo-seismology Stability of Structures

Master of Technology Thesis

Title: Analysis of Buried Pipelines Subjected to Reverse Fault MotionSupervisor: Prof. Sudhir K Jain

Abstract: Buried steel pipelines with continuous joints are commonly used for oil & gastransport. The pipeline may have to pass through an active fault zone on the way as itcarries the content over a long distance. It is then necessary to design the pipeline to safelyaccommodate the expected fault offset without breaking or rupture of the pipeline. Theexisting analytical methods developed for analysis of pipeline at fault crossing are suitablefor strike-slip fault and normal-slip faults. The inherent assumptions and simplificationsmake these methods unsuitable for the case of reverse fault crossing. The present studyproposes a simple finite element model for the analysis of pipeline at reverse fault crossing.The model has been developed using a commercial finite element software ABAQUS(Version 6.7). Buried pipeline has been modelled as a beam supported by nonlinear soil-

springs at discrete points. Performance of pipeline at reverse fault crossing has beenevaluated using the proposed model, under different conditions of crossing angle, dip angle,native soil & backfill property, pipe surface property and burial depth. Suitable designrecommendations for reverse fault crossing have been proposed based on the evaluatedperformance. An illustrative design example is presented at the end, which incorporates theproposed recommendations to improve pipelines performance at reverse fault crossing.


4/4

Undergraduate Project

Title: Mechanized Construction of Concrete Road Pavement Using Slip-Form Technique.Supervisor: Prof. Mrs. P. R. AdaviAbstract: Horizontal slip-form technique of road pavement construction using a slip formpaver was studied for its advantages and disadvantages. The entire procedure of roadconstruction using this technique was studied at an ongoing project of rehabilitation of NH-4 (Pune-Bangalore stretch). Different operational aspects of road paver machine wereinvestigated. The cost analysis was performed with available data to calculate the cost ofconstruction per meter of the road length.

Awards and Honours

Certificate of Merit for academic excellence in the Master of Technology Program inCivil Engineering for the year 2007-08 awarded by Indian Institute of Technology

Kanpur.

Secured 3rd prize in National Level Technical Paper Presentation competitionorganized by Maharashtra Institute of Technology Pune, 2006. (Topic of Paper:

Mechanized construction of concrete road pavement.)

Conferences/Workshops/Seminars Attended

International Symposium on Fire Risk Management by Underwriters Laboratories,Delhi, India, 5-6 Feb 2009

National Seminar On Seismic safety of Concrete Dams, Delhi, India, 27 Feb 2009 Workshop on Seismic Design of Concrete Gravity Dams (By Prof. A.K. Chopra from

University of California, Berkeley and Mr. Larry Nuss from U.S. Bureau of

Reclamation), IIT Kanpur, 3-6 March 2009

Extra Curricular Activities

Participated in Concrete cube test competition organized by Indian Chapter ofAmerican Concrete Institute in Dec. 2003.

Secured 1st prize in Inter-Dept. cricket competition organized by MaharashtraInstitute of technology, Pune in 2004.

Hobbies

Cricket Badminton Reading Novels Yoga

Documents

Resume Shantanu S Joshi 1