RETIRED: Retired products sold prior to the November 1 ... · x Ability to change disk size and user -defined properties at time of service creation ... QuickSpecs HP CloudSystem

QuickSpecs HP CloudSystem Matrix

Overview

c04111617 — DA – 13297 Worldwide — Version 36 — June 24 ,2016 Page 1

HP CloudSystem Matrix (Retired)

Starter Kit

Starter Kit - Front Starter Kit - Rear

1. Onsite CloudSystem Matrix Starter Kit Implementation 1. HP Intelligent Series rack, and rack and power options

NOTE: Rack is not included with the Matrix Starter Kit

2. Central Management Server (CMS)

HP ProLiant DL360p Gen8 server (recommended CMS)

2. Shown above with HP 3PAR StoreServ 7200 Storage. HP

Fibre Channels SAN supported include HP EVA, 3PAR F-

Series, T-Series, P10000 and 3PAR StoreServ 7200 , 7400 &

10000

3. Complete Matrix OE (including Insight Control) and Virtual

Connect Enterprise Manager.

3. Interconnect bays 3 & 4 available for additional HP Virtual

Connect FlexFabric modules (redundant pair)

OR (not shown) HP Virtual Connect 8Gb 24-Port FC modules

(redundant pair)

4. 16 half-height device bays available for populating with

server blades

4. HP Virtual Connect FlexFabric modules (redundant pair)

OR (not shown) HP Virtual Connect Flex-10 10-Gb Ethernet

modules (redundant pair), OR HP Virtual Connect Flex-

10/10D Module

5. HP BladeSystem c7000 enclosure, single phase

RETIRED: Retired products sold prior to the November 1, 2015 separation of Hewlett-Packard Company into Hewlett Packard Enterprise Company and HP Inc. mayhave older product names and model numbers that differ from current models.


Overview


Expansion Kit

Expansion Kit - Front Expansion Kit - Rear

1. Onsite CloudSystem Matrix Expansion Kit Implementation

Service (for Expansion Kit orders purchased after an initial

Matrix environment is implemented)

1. HP Virtual Connect FlexFabric modules (redundant pair)

OR (not shown) HP Virtual Connect Flex-10 10-Gb Ethernet

modules (redundant pair), OR (not shown) HP Virtual

Connect Flex-10/10D Module

2. 16 half-height device bays available for populating with

server blades

2. Interconnect bays 3 & 4 available for additional HP Virtual

Connect FlexFabric modules (redundant pair)

OR (not shown) HP Virtual Connect 8Gb 24-Port FC modules

(redundant pair)), OR (not shown) HP Virtual Connect Flex-

10/10D Module

3. Complete Matrix OE (including Insight Control) and Virtual

Connect Enterprise Manager

4. HP BladeSystem c7000 enclosure

NOTE: All HP CloudSystem Matrix infrastructure ships with licensed disaster protection for both physical and virtual servers, in

coordination with data replication provided by EVA, XP Continuous Access software, or 3PAR. Disaster recovery protection can be

achieved by implementing a secondary infrastructure at a remote location, and enabling storage replication between the two

sites.

What's New Updates for version 7.4 include:

Support for recently released HP ProLiant Gen9 servers (including BL460c blade for CloudSystem solutions)

Hyper-V enhancements (Generation 2 VMs, logical switches, RDM for HA VMs)

Ability to add/remove networks from physical servers

Ability to change disk size and user-defined properties at time of service creation



Overview


GUI customizations and organization enhancements

Storage support enhancements



Standard Features


Product Features HP CloudSystem Matrix is Infrastructure-as-a-Service (IaaS) for private and hybrid cloud environments,

allowing users to provision infrastructure in minutes for physical and virtual. This offering includes a

self-service infrastructure portal for quick auto-provisioning, along with built-in lifecycle management

to optimize infrastructure, manage the resource pools, and help ensure uptime. Matrix is integrated by

design with broad support of heterogeneous environments including cloud-bursting to a variety of

public cloud providers including HP Cloud Services.

Provision infrastructure and applications in minutes for physical and virtual.

Reduce TCO up to 56% with built-in infrastructure life-cycle management.

Integrated by design; includes support of heterogeneous environments.

HP Cloud Maps accelerate automation of cloud service deployments and ensure consistency and

reliability of the implementation of service catalogs.

HP CloudSystem Matrix is optimized for HP ProLiant and HP Integrity servers as well as HP storage and

HP networking, but also supports 3rd party x86 servers, networking, and storage. Supported operating

systems are Windows, Linux and HP-UX. Supported hypervisors include VMware, Microsoft HyperV, Red

Hat KVM, and Integrity VMs.

For more information above HP CloudSystem Matrix information, see: http://www.hp.com/go/matrix

For more information about HP BladeSystem, see: http://www.hp.com/go/bladesystem

For more information about HP Insight software, see: http://www.hp.com/go/insight

For more information about HP Virtual Connect, see: http://www.hp.com/go/virtualconnect

For more information about HP Storage, see: www.hp.com/go/storage

For more information about Factory Express, see:

http://h71028.www7.hp.com/enterprise/cache/97688-0-0-225-121.html

For more information about Cloud Service Automation for Matrix, see:

http://www.hp.com/go/csa4matrix



HP CloudSystem Matrix


How to order HP

CloudSystem Matrix Ordering HP CloudSystem Matrix

The method for purchasing HP CloudSystem Matrix is simple. Start by ordering a HP CloudSystem

Matrix Kit for ProLiant, which contains the infrastructure needed for a fully-working environment

supporting up to 16 HP ProLiant half-height server blades. Add additional kits now or in the future to

expand your HP CloudSystem Matrix infrastructure with additional infrastructure and blades. The

central management server (CMS) host implemented with the first kit simply extends its domain to

manage additional infrastructure that might be added with additional Matrix kits.

NOTE: Additional expansion kits may also be purchased separately. Expansion kits ordered separately

will come with the Matrix Expansion Kit Integration Implementation Service.

NOTE: Additional expansion kits purchased must be co-located with the initial kit to which they are

connecting to.

NOTE: For detailed ordering information please see the Configuration Information Factory Integrated

Models section of this QuickSpecs.

With all HP CloudSystem Matrix kit orders, the following services are included:

Factory services to default configure, rack, and cable the infrastructure in a rack,

Verify and update firmware for the entire solution being purchased (the CloudSystem Matrix

kits and the supported blades and options purchased with those kits) to the latest current

CloudSystem Matrix firmware release set. This ensures that the CloudSystem Matrix solution

will leave the factory with the right levels of firmware needed for the end to end solution to

be successful. (For specific version numbers supported and required, please refer to the HP

CloudSystem Matrix Compatibility Chart on http://www.hp.com/go/matrixcompatibility)

Coordinate hand-off to Technology Services (TS) or authorized partner. A TS or partner

project manager is assigned for managing pre-engagement and assigning a team of

engineers to perform the implementation service at the customer's site.

Factory Express custom configuration services should be added to the order if an EVA configuration is

also purchased in the same rack with Matrix kits, or if any other custom factory services are needed.

Factory Express uses its standard processes for capturing customer intent and requirements, as well

as providing order verification services.

While Factory Integration/Factory Express are building the CloudSystem Matrix environment for a

given customer, an assigned project manager from Technology Services (TS) will begin managing a

team of TS engineers to start planning the rollout of the implementation service, including engaging

with the customer on environmental requirements and related details. TS engineers will start the

actual implementation on the Matrix equipment as soon as possible after its arrival date at the

customer site.

NOTE: The account team must initiate contact with a Factory Express Engagement Project Manager

(EPM) to initiate the Factory Express processes, including communication of the Customer Intent

Document (CID).

The Technology Services CloudSystem Matrix Starter Kit Implementation Service is detailed in a

section below.





HP Matrix Operating

Environment

The HP Matrix Operating Environment is cloud management software for infrastructure as a service

(IaaS) that enables you to:

Design and provision infrastructure services in minutes via a self-service portal

Optimize infrastructure for capacity planning and showback/chargeback

Protect service continuity with automated cost-effective failover

The HP Matrix Operating Environment, which includes HP Insight Control, is at the core of the HP

CloudSystem Matrix, an infrastructure as a service (IaaS) solution for private and hybrid cloud

deployments, built on proven HP Converged Infrastructure technologies. It is available for both HP

ProLiant and HP Integrity servers as well as for provisioning third party x86 virtual machine

environments.

NOTE: See the HP Matrix Operating Environment for ProLiant QuickSpecs for more details

http://h18000.www1.hp.com/products/quickspecs/13050_div/13050_div.html

(Worldwide)


Starter Kit

Implementation Service

(onsite), plus additional

services

In addition to the CloudSystem Matrix Implementation Service, HP highly recommends HP Education

Services (for customer training and education) and additional Technical Services, as well as in-depth

installation or implementation services as needed. These recommended services are listed in the "HP

Care Pack services" section later in this document. The onsite CloudSystem Matrix Implementation

Service for the starter kit consists of these steps:

Upon delivery to customers site, unpack and inspect for damages

Integrate kits (included in the initial kit order, maximum of 5 total Matrix kits. Additional

Matrix expansion kits on same order require Matrix Expansion Kit Implementation Service)

hardware in to customers environment, power, network cabling

Installation and configuration of the central management server (CMS)

o Installation and configuration of the software required for management

Deployment of operating systems to configured LUNs on the optionally purchased EVA

P6000, 3PAR or other HP SAN or an existing SAN

o 1 HP server blade running a native OS of the customer's choice (Windows, Linux) on a

boot LUN

o 2 HP server blades each running a single hypervisor of the customer's choice

(VMware ESX, Microsoft Hyper-V or KVM), each on their own boot LUN (hypervisor

licenses are customer provided unless purchased from HP as part of the order)

NOTE: Installation and deployment of KVM requires additional service credits. See

section on Ordering CloudSystem Matrix.

Configuration of up to 2 VMs

o 1 HP server blade installed and configured to be a target for a blade move

Configure up to two physical target server operating systems to boot from SAN

o Orientation of the CloudSystem Matrix solution

o Navigation through installed components and all management software

o Review of the configured hardware components and their configuration

o Review of the completed system topology

o How to call HP for support

o Availability of additional services, educational services, etc. See:

http://www.hp.com/services/insight and http://www.hp.com/learn/proliant





o CloudSystem Matrix demonstrations. See: http://www.hp.com/go/matrix


Expansion Kit Integration


(onsite)

Ordering additional CloudSystem Matrix expansion kits after the initial CloudSystem Matrix kit order or

installing more than 5 total kits during the initial installation, includes the CloudSystem Matrix

Expansion Kit Integration Implementation Service. Each CloudSystem Matrix Expansion Kit

Implementation Service will integrate up to four Matrix expansion kits to an existing Matrix customer

environment (single Matrix CMS server). The onsite CloudSystem Matrix Expansion Kit Integration

Implementation Service for the Expansion Kits consists of these steps:

Upon delivery to customers site, unpack and inspect for damages

Integrate Matrix Expansion Kits hardware in to customers environment, power, network

cabling

o Change the firmware versions to be compatible with the version requirements of the

existing CloudSystem Matrix customer environment

Configure up to one physical target server operating systems to boot from SAN

Perform one of the CloudSystem Matrix demonstrations to verify the Expansion Kits

integration is completed successfully.


Conversion Services

HP CloudSystem Matrix Conversion Services convert your existing HP BladeSystem equipment into a

fully operational CloudSystem Matrix solution. Converting your existing equipment allows you to build

on the investment in your BladeSystem infrastructure and benefit from the advantages that a

CloudSystem Matrix solution provides. These services apply to both BladeSystem and BladeSystem-

based HP VirtualSystem infrastructures.

CloudSystem Matrix Conversion Services can be used in different combinations to create and/or

expand a CloudSystem Matrix, allowing you to:

Convert a single BladeSystem enclosure and BladeSystem equipment into an initial

CloudSystem Matrix configuration

Include additional enclosures during the conversion process

Expand your existing CloudSystem at any time by converting and incorporating your

BladeSystem enclosures

NOTE: For additional information, see:

http://h20195.www2.hp.com/V2/GetPDF.aspx/4AA3-9863ENw.pdf

Warranty services The support provided for CloudSystem Matrix uplifts the standard BladeSystem warranty to include

24x7 4hr onsite response for Matrix hardware and 2 hr response for software. Matrix customers will

have a system identifier for CloudSystem Matrix that, when provided to the call center by the

customer, routes the call to a specially trained team that can expertly support CloudSystem Matrix

specifically as well as the necessary software and firmware revisions to support it.

The HP CloudSystem Matrix infrastructure is covered by a global limited warranty and supported by HP

Services and a worldwide network of HP Authorized Channel Partners. Hardware diagnostic support

and repair is available for three years from date of purchase. Support for software and initial setup is

available for 90 days from date of purchase. Additional support may be covered under the warranty or





available for an additional fee.

Offered for CloudSystem Matrix are "uplift" HP Care Pack Services options that extend

warranty service period up to 4-, or 5- years across the entire hardware and software

infrastructure from the following default included levels of warranty support:

o Enclosure: Three-year, 24x7 (4 hour response) parts and labor, on-site limited global

warranty. Certain restrictions and exclusions apply

Enclosure options: fans, power supplies, Onboard Administrator, covered

with the enclosure warranty

HP Virtual Connect interconnects: 3 Year parts and labor, on-site regardless

of the warranty period for the system in which they are installed

o HP Insight software: 3 Year 24 x 7 Technical Support and Update Service

o HP Storage Fibre Channel switches have a maximum warranty period of one (1) year

regardless of the warranty period for the system in which they are installed

NOTE: For additional information, see: http://www.hp.com/go/bladesystem and

http://www.hp.com/services/insight.

HP Matrix Operating

Environment Support

HP Matrix Operating Environment includes three years of 24 x 7 HP Software Technical Support and

Update Service. This service provides access to HP technical resources for help in resolving software

implementation or operations problems. The service also provides access to software updates and

reference manuals either in electronic form or on physical media as they are made available from HP.

With this service, HP CloudSystem Matrix users benefit from expedited problem resolution and

proactive notification and delivery of software updates.

As part of your implementation service, HP services personnel or your authorized provider will activate

your HP Software Technical Support and Update Service for Matrix OE at:

http://www.hp.com/services/insight.

Your Service Agreement Identifier (SAID) will be delivered to you after registration. After you have

received your SAID, you can go to the software update manager (SUM) web page to view your contract

online and elect electronic delivery (in addition to standard media-based updates). For more

information about this service, see: http://www.hp.com/services/insight.

HP offers a number of software support services, many of which are provided to customers at no

additional charge.

Join the Discussion at: http://www.itrc.hp.com

The HP Support Forum is a community-based, user supported tool for HP customers to participate in

discussions amongst the customer community about HP products. For discussions related to HP

Insight software, see the "Management Software and System Tools" area.

HP Worldwide Customer Service contact numbers are available at:

http://www.hp.com/country/us/en/wwcontact.html.

HP CloudSystem Matrix --

Extended Infrastructure

HP Matrix Operating Environment extends its software functionality beyond HP CloudSystem Matrix

across all HP ProLiant and HP Integrity servers as well as any x86 3rd party servers which are





supported by VMware, Microsoft HyperV and Red Hat KVM.

CloudSystem Matrix support for this extended infrastructure includes key capabilities of HP Matrix

Operating Environment such as designing, self-service portal with auto-provisioning for virtual

environments and capacity planning, i.e. physical server deployment is not supported (NOTE: recovery

management for virtual only is supported on HP rackmount servers and HP blade servers without

Virtual Connect). All capabilities of HP Matrix Operating Environment are supported for HP

BladeSystem servers with Virtual Connect.

NOTE: See the HP Matrix Operating Environment for ProLiant QuickSpecs for additional information:


(Worldwide)

CloudSystem Matrix for supported extended virtual machine managed nodes is listed in the HP Insight

Software Support Matrix document for Matrix Operating Environment.

Customer support for Matrix extended infrastructure servers is handled the same way as HP Matrix

Operating Environment standalone software. Matrix extended infrastructure is subject to the same

software licensing requirements as Matrix Operating Environment.

NOTE: See the HP Matrix Operating Environment for ProLiant QuickSpecs for more details


(Worldwide)

HP Financial Services To support customers' transition, HP Financial Services (HPFS) can help in a way that you may not have

considered. HPFS can help you invest in your business while preserving precious capital.

For more information, contact your local HP Financial Services Representative. In the United States,

call 1-888-277-5942. In Canada, dial 1-800-HP-LEASE. For more information please visit:

http://www.hp.com/hpfinancialservices for links to HP Financial Services around the world.

HP ProLiant Instant

Capacity Program (U.S.

only)

The ProLiant Instant Capacity program (U.S. only) provides cost-effective "just in time" inventory

protection. ProLiant iCAP is designed to provide "ready to run" servers for immediate activation, while

avoiding up-front costs.

Supported servers include BladeSystem ProLiant (and ML/DL) servers deployed via Direct

fulfillment

Uses HP Systems Insight Manager, automated, billing and tracking process upon activation

and consumption

Servers can be pre-racked, pre-imaged, and tested in preparation of activation

Amortize total blade infrastructure (rack, enclosure, power, interconnects) over the total

number of blades

Warranty commences once customer has been invoiced (title exchanges)

Price captured at time of shipment

Ability to reset target inventory levels in real time

HP Utility Ready

Computing on Matrix

HP Utility Ready Computing blades (URB) are pay-for-use infrastructure that resides at your site, billed

monthly by HP based on metered power-on time, and transfers cost of blade servers and associated

infrastructure from CapEx to OpEx in an alternative way from a traditional lease.





The URB Advantage:

Aligning costs with utilization

Reduce upfront expenses

React instantly to changing demands

Effective Chargeback mechanism

And it's at your site, you maintain control!

With CloudSystem Matrix, customers can add Utility Ready Computing blades to their Matrix enclosures

and leverage the benefits offered by utility ready computing.

NOTE: Customers cannot mix non-URC blades with URC blades same in same enclosure, they should be

housed in separate enclosures.

NOTE: For additional information, please see:

http://h18000.www1.hp.com/products/blades/components/utility.html?jumpid=reg_R1002_USEN

Factory Express Portfolio

for Servers and Storage

For HP CloudSystem Matrix, HP Factory Express services are added if the EVA P6000 SAN or 3PAR is

purchased with the CloudSystem Matrix Starter Kit. If other custom requirements or intents are

required for a given customer's CloudSystem Matrix order, Factory Express capabilities may also be

called upon. HP Factory Express offers configuration, customization, integration and deployment

services for HP servers and storage products. Customers can choose how their factory solutions are

built, tested, integrated, shipped and deployed.

Factory Express offers service packages for simple configuration, racking, installation, complex

configuration and design services as well as individual factory services, such as image loading, asset

tagging and custom packaging. HP products supported through Factory Express include: a wide array

of servers and storage: HP Integrity servers, HP ProLiant servers, HP ProLiant & Integrity c-Class

BladeSystem server blades, HP 9000 servers as well as the MSAxxxx, VA7xxx, EVA, and XP storage

products, rackable tape libraries and configurable network switches.

For more information on Factory Express services please contact your sales representative or go to:

http://www.hp.com/go/factory-express

HP Simple Configurator SCE is a guided self service tool to help sales and non technical people provide customers with initial

configurations in 3 to 5 minutes. You may then send the configuration on for configuration help, or use

in your existing ordering processes. If you require "custom" rack configuration or configuration for

products not available in SCE, please contact HP's Customer Business Center or an Authorized Partner

for assistance. http://www.hp.com/products/configurator

Rack Airflow

Requirements

HP rack cabinets

The increasing power of new high-performance processor technology requires increased cooling

efficiency for rack-mounted servers. The HP 10000 G2 Series racks provide enhanced airflow for

maximum cooling, allowing these racks to be fully loaded with servers using the latest processors.

NOTE: For operation with the DC Input Module the HP 1200mm deep rack is required to allow DC power

cabling to be installed

CAUTION: CloudSystem Matrix infrastructures are best fulfilled with HP racks. However, if a third-party





rack is used, observe the following additional requirements to ensure adequate airflow and to prevent

damage to the equipment:

Front and rear doors: If your 42U server rack includes closing front and rear doors, you must

allow 830 square inches (5,350 sq cm) of holes evenly distributed from top to bottom to

permit adequate airflow (equivalent to a required 64 percent open area for ventilation).

The clearance from face of rack to inside of the front door needs to be a minimum of 1.75".

Side: The clearance between the installed rack component and the side panels of the rack

needs to be a minimum of 2.75 inches (7 cm).

Depth: a minimum of 39.4 inches (1000mm) for AC power, 47 inches (1200mm) for DC power

input

Adjustable rack rails are shipped with each enclosure:

o Minimum rail length: 25 inches (635mm)

o Maximum rail length: 34 inches (864mm)

CAUTION: Always use blanking panels to fill all remaining empty front panel U-spaces in the rack. This

arrangement ensures proper airflow. Using a rack without blanking panels will result in improper

cooling that can lead to thermal damage.



Ordering CloudSystem Matrix


Configuration Information Factory Integrated Models - HP CloudSystem Matrix - Starter Kit

NOTE: This section lists the required steps for ordering a HP CloudSystem Matrix.

NOTE: All HP CloudSystem Matrix infrastructure ships with licensed disaster recovery protection for both physical and virtual

servers, in coordination with data replication provided by EVA or XP Continuous Access software. Disaster recovery protection can

be achieved by implementing a secondary infrastructure at a remote location, and enabling storage replication between the two

sites.

NOTE: To ensure only valid configurations are ordered, HP recommends the use of an HP approved configurator or contact your

local sales representative for additional information on product offerings and requirements.

NOTE: FIO indicates that this option is a Factory Integrated Option.

Step 1: Select HP Intelligent Series Rack (Recommended, per notes immediately below) NOTE: For additional HP Rack information please visit:

http://h18004.www1.hp.com/products/servers/proliantstorage/racks/intelligentseries/index.html

NOTE: For additional Rack Options please see the "Additional Options" section of this QuickSpecs.

NOTE: The Starter Kit is recommended to be ordered with an HP rack. When not ordering with a rack, it is necessary for the

customer to rack any CloudSystem Matrix enclosures in a rack prior to HP arriving onsite to complete the CloudSystem Matrix

Implementation Service. You may purchase the HP Install c7000 Enclosure and Server Build Service to assist with onsite racking

and cabling of CloudSystem Matrix enclosures into a rack. See the "HP Care Pack services" section later in this document for the

part numbers. HP Rack Series HP Intelligent Series racks

HP 642 1075mm Shock Intelligent Series Rack BW904A

HP 642 1075mm Pallet Intelligent Series Rack BW903A







NOTE: Please see the QuickSpecs for Technical Specifications and additional

information:


(Worldwide)

NOTE: For additional information regarding Rack Cabinets, please see the following

URL: http://www.hp.com/go/rackandpower.

Step 2: Select Required Configurable HP CloudSystem Matrix Starter Kit (Choose one of the

following from each list unless otherwise noted)

HP CloudSystem

Matrix Starter Kit

NOTE: Starter Kit default components means HP ordering systems will default these

selections when any unique HP CloudSystem Matrix part number is entered. The default

selections can be changed to meet customer needs.

NOTE: The Starter Kit does not include a central management server or CMS (see

BladeSystem c-Class server blades section below for CMS server).

Hardware Components

HP CloudSystem Matrix for ProLiant v2 Kit 708919-B21





NOTE: The configurable starter kit can be defined as either Starter or Expansion Kit with

applicable services applied appropriately when configured.

HP CloudSystem Matrix Modular Kit (Hardware Components) includes:

HP BladeSystem c7000 enclosure and 10 fans

HP BladeSystem c7000 Onboard Administrator with KVM (keyboard, video,

mouse) option, redundant pair

HP Virtual Connect Option (required choice of one):

HP Virtual Connect FlexFabric 10Gb 24-port Module, redundant pair

HP Virtual Connect Flex-10 10GB 24-port Module, redundant pair with HP Virtual

Connect 8Gb 24-port Fibre Channel Module, redundant pair

HP Virtual Connect Flex-10/10D 30-port Module, redundant pair with HP Virtual

Connect 8Gb 24-port Fibre Channel Module, redundant pair

c7000 Power Option (required choice of one):

Single phase (QTY of 6)

3-Phase (QTY of 6)

DC Power (QTY of 6)

HP Matrix OE Software (required choice of one)

Matrix Operating Environment 16-server license, 3 year 24/7 support and

updates


updates

NOTE: Additional Matrix OE licenses may be purchased separately.,

NOTE: See the HP Matrix Operating Environment for ProLiant QuickSpecs for additional

information:


(Worldwide)

NOTE: Following are the VC FlexFabric transceiver/SFP options.

HP BladeSystem c-Class 10Gb SFP+ SR Transceiver 455883-B21

HP BladeSystem c-Class 10Gb SFP+ LR Transceiver 455886-B21

HP BladeSystem c-Class 10Gb SFP+ LRM Transceiver 455889-B21

HP BladeSystem c-Class Virtual Connect 1G SFP SX Transceiver 453151-B21

HP BladeSystem c-Class Virtual Connect 1G SFP RJ-45 Transceiver 453154-B21

HP 8Gb Shortwave B-series Fibre Channel 1 Pack SFP+ Transceiver AJ716B

HP 8Gb Long Wave B-series 10km Fibre Channel 1 Pack SFP+ Transceiver AJ717A

HP 8Gb Short Wave Fibre Channel SFP+ 1 Pack AJ718A

NOTE: Following are the VC Flex-10 10Gb Ethernet module transceiver/SFP options.

Software Licenses and media





HP Matrix Operating Environment SW for 16 Server and VCEM for c7000 Enclosure with

3yr 24x7 Support

BD683B

HP Matrix Operating Environment SW for 8 Server and VCEM for c7000 Enclosure with 3yr

24x7 Support

NOTE: One (1) entitlement order number is provided.

NOTE: If the ordering system default of 3 years Technical Support and Update Service is

rejected or not selected, the basic 1 year Technical Support and Update Service will

apply.

BD578B

NOTE: The management software licenses packaged with HP CloudSystem Matrix

provide licensing to manage HP ProLiant c-Class server blades only, except for Virtual

Connect Enterprise Manager software (VCEM) as this is licensed to the actual

BladeSystem c7000 enclosure. HP Integrity c-Class server blades require separate

licensing. HP-UX customers should order licenses for the HP-UX 11i v3 Virtual Server

Environment OE (VSE-OE) or HP-UX 11i v3 Data Center OE (DC-OE) (see:

http://www.hp.com/go/hpux).


HP Implementation service for the CloudSystem Matrix Starter Kit UK831E

HP CloudSystem Matrix Starter Kit - Implementation Service, Flexible HA115A1-5NL

NOTE: Includes the installation & configuration of any Matrix Expansion Kit included in

the order.

Central Management

Server

HP CloudSystem Central Management Kit (DL360p Gen8 128G 2P Server 3y 24x7 Support

NOTE: This is the default part number for the Matrix central management server (CMS),

to host the management software. It may be substituted with another server configured

per notes below and per CMS sizing, scalability, and redundancy preferences.

G6X20A

HP ProLiant DL360p Gen8 CMS server (PN G6X20A) is configured as follows:

Dual processors - Intel® Xeon® E5-2650v2 processor

128 GB (8 x 16GB) 16GB 2Rx4 PC3-14900R-13 Kit Registered DIMMs

HP 2GB FBWC for P-Series Smart Array

FlexFabric 10Gb 2P 554FLR-SFP+ Adapter Ethernet 1Gb 4-port 331T Adapter

8x HP 300GB 6G SAS 15K 2.5in SC ENT HDD

HP 82Q 8Gb Dual Port PCI-e Fibre Channel Host Bus Adapter

HP 9.5mm SATA JB DVDRW Optical Drive

HP DL360 3 Year, 24x7 4 Hour Response Hardware support

NOTE: Considerations for Central Management Server (CMS) - choice of rack-mount or

blade server: HP offers a choice of rack-mounted ProLiant server (DL or ML) as central

management server host for HP CloudSystem Matrix. HP recommends the rack-mounted

ProLiant DL360p Gen8 as the CMS host (see configuration below) for those customers

who desire to use all available and licensed enclosure blade bays for managed target

blades and workloads. When multiple management server hosts are required for

scalability and high availability or hosting partner management software, multiple

ProLiant DL/ML servers or server blades (or even a combination of blade or rack-

mounted servers) can be installed and configured to work together to manage the

CloudSystem Matrix environment.

This CMS will be devoted to running the CloudSystem Matrix management software;

other management software such as VMware vCenter Server should be installed on a





separate server.

NOTE: Larger environments may warrant having multiple CMS servers for these reasons:

scalability, high availability of the management server and data, and separation of

database or management components for performance or security access reasons.

NOTE: If the recommended HP ProLiant DL360p Gen8 configuration above is not

purchased, the customer agrees to supply or purchase other HP ProLiant rack-mount

server(s) or HP ProLiant server blade(s) that meet the requirements. See also the CMS

requirements in this Insight Management Support Matrix Chapter 2 "Central Management

Server Requirements" for more information:

http://bizsupport2.austin.hp.com/bc/docs/support/SupportManual/

c03341309/c03341309.pdf

NOTE: This CMS should be implemented on a 64-bit Windows operating system. (see

Matrix compatibility chart at http://www.hp.com/go/matrixcompatibility)

Target server blades

NOTE: It is highly recommended that at least four (4) additional HP ProLiant c-Class

blades be ordered with each Starter Kit, because the Onsite Implementation Service

includes provisioning of up to four (4) HP ProLiant blades, two of which are directly

provisioned as physical servers and two of which are virtual machine hosts. See separate

section on "CloudSystem Matrix Starter Kit Implementation Service" for details. All

shipping HP ProLiant c-Class blades are supported except the HP ProLiant BL2x220c

server blades and workstation blades.

NOTE: For server blade information, please visit:

http://h18000.www1.hp.com/products/quickspecs/division/12534.html

NOTE: HP ProLiant server blades should be configured to connect via the Virtual Connect

modules included in the CloudSystem Matrix kits. See the sections below on FlexibleLOM

and Mezzanine options for further details.

HP Integrity Servers

NOTE: All shipping HP Integrity c-Class blades are supported when configured with

Integrity software products. For additional server blade information please visit:

http://h18004.www1.hp.com/products/quickspecs/division/division.html#12391.


provide licensing to manage HP ProLiant c-Class server blades and Virtual Connect

Enterprise Manager software (VCEM) which is licensed to the BladeSystem c7000

Enclosure. HP Integrity c-Class server blades require separate licensing (except for VCEM

software). HP-UX customers should order licenses for the HP-UX 11i v3 Virtual Server

Environment OE (VSE-OE) or HP-UX 11i v3 Data Center OE (DC-OE) For additional

information, please visit: http://www.hp.com/go/hpux. Please refer to ordering

information for Integrity Matrix at: www.hp.com/go/matrix.

KVM Management

Server

To utilize management of KMV hosts and guests an additional, dedicated management

server is required. This KVM management server will be connected to and managed by,

via network, the Matrix Central Management Server (listed above). Installation and

configuration of the KVM Management Server requires that an additional 3

Implementation days (HK928A1) to be added to the standard CloudSystem Matrix

installation offering.





NOTE: Specific hardware and software configuration guidelines for the KVM Management

Server can be found within the HP Insight Management Support Matrix, which can be

located within the document list at

http://h18013.www1.hp.com/products/servers/management/unified/infolibrary_ic.html

KVM Managed Hosts CloudSystem Matrix supports KVM managed hosts on servers that are generally

supported by Matrix. Specifically, they can be within Matrix enclosures or ProLiant DL or

SL servers. ProLiant blades must be housed in either the Matrix Starter or Expansion Kit.

The KVM managed hosts may be contained in the same enclosure as other non-KVM

hypervisor hosts, or a separate enclosure. The supported KVM blade host must have the

following minimum configuration:

NOTE: Specific hardware and software configuration guidelines for the KVM Managed

Hosts can be found within the HP Insight Management Support Matrix, which can be

located at

http://h18013.www1.hp.com/products/servers/management/unified/infolibrary_ic.html

Federated Central

Management Servers

for CloudSystem

Matrix

To scale beyond a single CloudSystem central management server (CMS) server node

limits (physical+virtual), a federated CMS model has been developed.

For more information on CloudSystem Matrix federated CMS implementations please

refer to: http://h20195.www2.hp.com/V2/GetDocument.aspx?docname=4AA3-

4721ENW&cc=us&lc=en

HP requires the following components when implementing a federated CMS solution:

Additional CMS servers - HP recommends HP CloudSystem Matrix Central Mgmt

Svr based on DL360p Gen8, 32GB, 2P Server (PN 66224-B21) as each CMS when

adding additional CloudSystem Matrix management servers. See Central

Management Server section in this document for more information about this

configuration.

HP Insight Control license on each CloudSystem Matrix CMS server. NOTE: The

above server (PN 66224-B21) includes a license for Insight Control.

CloudSystem Matrix Implementation and Startup services for each additional

CMS. Please see the Services section below in this QuickSpecs for additional

details.

NOTE: If installation is using KVM managed nodes in a federated CMS configuration, the

KVM management server must be managed by the top-level Matrix CMS.

HP Interconnect

Options

NOTE: The Virtual Connect interconnect modules that are built in to the Starter and

Expansion kits are not removable. Interconnect bays 3 and 4 are available for additional

Virtual Connect (VC) FlexFabric modules in HP CloudSystem Matrix with FlexFabric Starter

and Expansion kits. Additional supported interconnected options may be added to the

remaining available interconnect bays (bays 5/6 and 7/8).

NOTE: HP Virtual Connect FlexFabric 10Gb/24-port Modules should not be added to

existing CloudSystem Matrix c7000 enclosures that are using HP Virtual Connect Flex-10

10Gb Ethernet modules and HP Virtual Connect 8Gb 24-Port FC Modules for BladeSystem

c-Class. Mixing of Virtual Connect FlexFabric and non-FlexFabric legacy Virtual Connect

modules is not permitted.





NOTE: For supported CloudSystem Matrix interconnect options, see the Compatibility

chart at: http://www.hp.com/go/matrixcompatibility.

NOTE: For HP BladeSystem c-Class Interconnect and Mezzanine Components please visit:

http://h18004.www1.hp.com/products/blades/components/c-class-interconnects.html

http://h18004.www1.hp.com/products/blades/components/c-class-adapters.html

Step 3: Select HP CloudSystem Matrix Expansion Kits


Expansion Kit

NOTE: Add additional Expansion Kits as your CloudSystem Matrix environments

requires or on an as-needed basis.

NOTE: Expansion Kits purchased must be co-located with the Starter Kit(s) to which

they are connecting.

NOTE: Add HP server blades and other recommended options to the Expansion Kit as

desired. Depending on quantity of Expansion Kits purchased, additional racks,

storage arrays, and other options may also be warranted.

NOTE: Refer to the HP CloudSystem Matrix compatibility chart at:

http://www.hp.com/go/matrixcompatibility for details on supported options,

operating systems, etc.

Hardware plus software licenses

HP CloudSystem Matrix for ProLiant v2 Kit

NOTE: The configurable starter kit can be defined as either Starter or Expansion Kit

with appropriate services applied appropriately when configured.

708919-B21

HP CloudSystem Matrix Modular Kit (Hardware Components) includes:

HP BladeSystem c7000 enclosure and 10 fans

HP BladeSystem c7000 Onboard Administrator with KVM option, redundant

pair

HP Virtual Connect Option (required choice of one):

HP Virtual Connect FlexFabric 10Gb 24-port Module, redundant pair

HP Virtual Connect Flex-10 10GB 24-port Module, redundant pair with HP

Virtual Connect 8Gb 24-port Fibre Channel Module, redundant pair

HP Virtual Connect Flex-10/10D 30-port Module, redundant pair with HP

Virtual Connect 8Gb 24-port Fibre Channel Module, redundant pair

c7000 Power Option (required choice of one):

Single phase (QTY of 6)

3-Phase (QTY of 6)

DC Power (QTY of 6)

HP Matrix OE Software (required choice of one)


updates


updates





NOTE: Additional Matrix OE licenses may be purchased separately. ,

NOTE: See the HP Matrix Operating Environment for ProLiant QuickSpecs for

additional information:


(Worldwide)

NOTE: Following are the VC FlexFabric transceiver/SFP options.






HP 8Gb Shortwave B-series Fibre Channel 1 Pack SFP+ Transceiver AJ716B

HP 8Gb Long Wave B-series 10km Fibre Channel 1 Pack SFP+ Transceiver AJ717A

NOTE: Following are the VC Flex-10 10Gb Ethernet module transceiver/SFP options.







HP Implementation service for the CloudSystem Matrix Expansion Kit UU959E

HP CloudSystem Expansion Kit - Implementation Service, Flexible HA115A1-5P9

NOTE: The Matrix Expansion Kit Integration Implementation Service is required for

any purchased Expansion Kit being added to an existing Matrix environment. The

Matrix Expansion Kit Integration Service supports the integration of up to four Matrix

Expansion Kits into the existing Matrix environment.

Step 4: Select Recommended options for HP CloudSystem Matrix Kits

NOTE: Supported options may be added to the Starter or Expansion Kit as desired.

NOTE: For additional options, please refer to the "Additional Options" section below. For additional blade enclosures, interconnect

options, and power subsystem options, please refer to the following QuickSpecs:

HP BladeSystem c7000 Enclosure QuickSpecs:


and HP BladeSystem c-Class Interconnect and Mezzanine Components:

http://h18004.www1.hp.com/products/blades/components/c-class-interconnects.html


BladeSystem c-Class

target server blades

HP ProLiant server blades

NOTE: All shipping HP ProLiant c-Class blades are supported except the HP ProLiant

BL2x220c server blades and workstation blades. For server blade information,

please visit: http://h18000.www1.hp.com/products/quickspecs/division/12534.html

NOTE: It is highly recommended that at least four (4) additional HP ProLiant c-Class

blades be ordered with each Starter Kit, because the Onsite Implementation Service

includes provisioning of up to four (4) HP ProLiant blades, two of which are directly

provisioned as physical servers and two of which are virtual machine hosts. See





separate section on "CloudSystem Matrix Starter Kit Implementation Service" for

details.

NOTE: HP ProLiant server blades should be configured to connect via the Virtual

Connect modules included in the CloudSystem Matrix kits. See the section below on

Mezzanine options for further details.

NOTE: The HP BladeSystem c7000 Enclosure holds up to 16 half-height blades.

Server blanks will be shipped in all empty bays.

HP Integrity Servers

NOTE: All shipping HP Integrity c-Class blades are supported when configured with

Integrity software products. For additional server blade information please visit:

http://h18004.www1.hp.com/products/quickspecs/division/division.html#12391.


provide licensing to manage HP ProLiant c-Class server blades and Virtual Connect

Enterprise Manager software (VCEM) which is licensed to the BladeSystem c7000

Enclosure. HP Integrity c-Class server blades require separate licensing (except for

VCEM software). HP-UX customers should order licenses for the HP-UX 11i v3 Virtual

Server Environment OE (VSE-OE) or HP-UX 11i v3 Data Center OE (DC-OE) For

additional information, please visit: http://www.hp.com/go/hpux. Please refer to

ordering information for Integrity Matrix at: www.hp.com/go/matrix.

Interconnect options NOTE: The Virtual Connect interconnect modules that are built in to the Starter and

Expansion kits are not removable. Interconnect bays 3 and 4 are available for

additional Virtual Connect (VC) FlexFabric modules in HP CloudSystem Matrix with

FlexFabric Starter and Expansion kits. Additional supported interconnected options

may be added to the remaining available interconnect bays (bays 5/6 and 7/8).

NOTE: HP Virtual Connect FlexFabric 10Gb/24-port Modules should not be added to

existing CloudSystem Matrix c7000 enclosures that are using HP Virtual Connect

Flex-10 10Gb Ethernet modules and HP Virtual Connect 8Gb 24-Port FC Modules for

BladeSystem c-Class. Mixing of Virtual Connect FlexFabric and non-FlexFabric legacy

Virtual Connect modules is not permitted.

NOTE: For supported CloudSystem Matrix interconnect options, see the Compatibility

Chart at: http://www.hp.com/go/matrix.

NOTE: For HP BladeSystem c-Class Interconnect and Mezzanine Components:

http://h18004.www1.hp.com/products/blades/components/c-class-

interconnects.html


HP Networking NOTE: For servers that require one FlexibleLOM to be installed in the FlexibleLOM

connector. All FlexibleLOMs are dual port: One port is routed to interconnect module

bay 1 and the other to bay 2. For supported CloudSystem Matrix FlexibleLOM

options, see the Compatibility chart at: http://www.hp.com/go/matrixcompatibility.

10Gb FlexibleLOM Adapters

HP FlexFabric 10Gb 2-port 554FLB FIO Adapter 684212-B21

HP Flex-10 10Gb 2-port 530FLB FIO Adapter 684211-B21

NOTE: Flex-10 adapters are compatible with FlexFabric, but are limited to Flex-10

functionality only. Do not configure Flex-10 adapters into c-Class server blades in

any CloudSystem Matrix FlexFabric kit.

Mezzanine Options NOTE: For supported CloudSystem Matrix mezzanine options, see the Compatibility

chart at: http://www.hp.com/go/matrixcompatibility.





8Gb Fibre Channel Mezzanines

HP LPe1205A 8Gb Fibre Channel Host Bus Adapter for BladeSystem c-Class 659818-B21

HP QMH2572 8Gb Fibre Channel Host Bus Adapter for BladeSystem c-Class 651281-B21

Emulex LPe1205 8Gb Fibre Channel Host Bus Adapter for c-Class BladeSystem 456972-B21

QLogic QMH2562 8Gb Fibre Channel Host Bus Adapter for c-Class BladeSystem 451871-B21

NOTE: A Fibre Channel host bus adapter card is required for each server blade

connecting to a HP Virtual Connect 8Gb 24-Port Fibre Channel Module for c-Class

BladeSystem in bays 3-4 (i.e. for all blades in a Matrix with Flex-10 Starter or

Expansion kit).

10Gb Ethernet Converged Network Adapter Mezzanines

HP FlexFabric 10Gb 2-port 554M Adapter 647590-B21

HP NC553m 10Gb 2-port FlexFabric Adapter 613431-B21

HP BLc NC551m Dual Port FlexFabric 10Gb Converged Network Adapter 580151-B21

NOTE: Required for each server blade connecting to a VC FlexFabric module in bays

3-4 (i.e. when a Matrix with FlexFabric Starter or Expansion kit is purchased with

additional FlexFabric modules).

Support Plus 24 options

for CloudSystem Matrix

Starter Kit

NOTE: 3-year Support Plus 24 for the entire CloudSystem Matrix Starter Kit hardware

and software (default selection). This Support Plus 24 raises the support levels of all

the Matrix components uniformly up to 3 years for easier tracking of warranty

support.

Proactive Select - 3 year 24x7 30 credits per year, Flexible HG921A3#12L

4 year 24x7 BL Matrix Software Support, Flexible HA107A4#9K2

5 year 24x7 BL Matrix Software Support, Flexible HA107A5#9K2

Support Plus 24 - 4 year Support Plus 24 BLc Matrix Software Support, Flexible HA110A4#9K2

Support Plus 24 - 5 year Support Plus 24 BLc Matrix Software Support, Flexible HA110A5#9K2

Proactive 24 - 4 year Support Plus 24 BLc Matrix Software Support, Flexible HA111A4#9K2

Proactive 24 - 5 year Support Plus 24 BLc Matrix Software Support, Flexible HA111A5#9K2

Critical Service - 3 year Support Plus 24 BLc Matrix Software Support, Flexible HA112A3#9K2





Support Plus 24 options

for CloudSystem Matrix

Expansion Kit

NOTE: 3-, 4-, and 5-year Support Plus 24 Care Pack uplifts are available for the

entire CloudSystem Matrix Starter Kit hardware and software. Support Plus 24 raises

the support levels of all the Matrix components uniformly up to 3-5 years for easier

tracking of warranty support.

HP 4 year Support Plus24 BLc7000 Matrix Expansion Service UM860E

HP 5 year Support Plus24 BLc7000 Matrix Expansion Service UM861E

4 year Support Plus 24 BLc Matrix Expansion Kit Support, Flexible HA110A4#9K1

5 year Support Plus 24 BLc Matrix Expansion Kit Support, Flexible HA110A5#9K1

Proactive 24 - 4 year Support Plus 24 BLc Matrix Expansion Kit Support, Flexible HA111A4#9K1

Proactive 24 - 5 year Support Plus 24 BLc Matrix Expansion Kit Support, Flexible HA111A5#9K1





Critical Service - 3 year Support Plus 24 BLc Matrix Expansion Kit Support, Flexible HA112A3#9K1



24x7 4hr HW Support - 4 year Support Plus 24 BLc Matrix Expansion Kit Support,

Flexible

HA104A4#9K1

24x7 4hr HW Support - 5 year Support Plus 24 BLc Matrix Expansion Kit Support,

Flexible

HA104A5#9K1

24x7 SW Support - 4 year Support Plus 24 BLc Matrix Expansion Kit Support, Flexible HA107A4#9K1

24x7 SW Support - 4 year Support Plus 24 BLc Matrix Expansion Kit Support, Flexible HA107A5#9K1

Hypervisor

Licensing

VMware vSphere Enterprise Plus licenses for CloudSystem Matrix

NOTE: Buy one per CloudSystem Matrix Starter/Expansion kit (supports up to 32

processor sockets).

VMware vSphere Enterprise Plus 32P 3yr 24x7 No Media License TC290A

VMware vSphere Installation & Startup Enterprise Service, Flexible HA124A1#5NS

HP Installation and Startup of Vmware Vsphere Enterprise or Enterprise Plus UK837E

VMware vCenter Server Standard for vSphere

VMware vCenter Standard for vSphere 1yr No Media License

NOTE: 4.0 here refers to vSphere, not ESX 4.0. Reference the Matrix compatibility

chart at: http://www.hp.com/go/matrixcompatibility for the latest supported ESX

versions.

NOTE: vCenter is licensed per instance (one needed per management domain).

NOTE: This does not include VMware vCenter for vSphere implementation services,

which may be purchased separately.

571780-B21

VMware vSphere Enterprise Plus individual licenses, per processor socket

VMware vSphere Enterprise Plus 1P 1yr 9x5 No Media License

NOTE: 4.0 here refers to vSphere, not ESX 4.0. Reference the Matrix compatibility

chart at: http://www.hp.com/go/matrixcompatibility for the latest supported ESX

versions.

NOTE: This 4.0 license can be used with prior ESX versions, for example, ESX 3.5.

NOTE: Includes technical support and updates for 1 year. For more information, see:

http://h18006.www1.hp.com/products/servers/software/vmware/index.html

NOTE: One instance of VMware vCenter Server (see below) is required to enable

vSphere features such as VMware VMotion, VMware Distributed Resource Scheduler,

and more.

571774-B21

Microsoft Windows Server 2008 with Hyper-V licenses

Microsoft Windows 2008 Server Standard Edition 5CAL Factory Integrated Not Pre-

installed Software

468721-B21

Windows Server 2008 Enterprise Edition OS Not Pre-Installed, FIO (includes 4 Hyper-

V licenses)

468723-B21

HP P6300 EVA

(factory integrated)

P6300 EVA Factory Integrated Starter Kit with (8) 600GB 10K SFF drives

NOTE: This kit is only for Factory Integration and requires the #0D1option.

HP P6300 EVA (8) 600GB 10K SFF SAS Factory Integrated Starter Kit

NOTE: Order additional 600GB 10K RPM SFF SAS disk drives as needed to

add capacity

P6000 Command View/ABM installed with restore CD

AP891A





NOTE: P6000 SmartStart software, containing P6000 Command View/SBM

software, either on a CD or an e-copy, if needed, can be ordered separately

P6300 Unlimited Command View LTU

XCS v10.x Firmware installed with restore CD

HP P6300 EVA Additional Components

HP 8/40 Power Pack+ (24) Full Fabric Ports Enabled SAN Switch AM870A

HP 8/40 Base (24) Full Fabric Ports Enabled SAN Switch AM869A

HP 8/24 Base (16) Full Fabric Ports Enabled SAN Switch AM868A

NOTE: Required to connect the blade enclosure to the EVA, if customer needs a top

of rack B-series SAN switch.

HP 8/20q Fibre Channel 8-ports Active Switch AQ233A

HP 8/20q Fibre Channel Switch AK242A

HP SN6000 Stackable 8Gb 24-port Single Power Fibre Channel Switch AW575A

HP SN6000 Stackable 8Gb 24-port Dual Power Fibre Channel Switch AW576A

HP SN6000 Stackable 12-port Single Power FC Switch

NOTE: Required to connect the blade enclosure to the EVA, if customer needs an H-

series SAN switch (top of rack).

BK780A

Optional Components

HP CP 3Y Support Plus 24 HA110A3

HP CP Installation & Startup HA114A1

HP CP Tech Installation and Startup HA124A1

HP EVA Loopback Connector AJ706A

HP P6000 SmartStart V3.4 E-Media Kit T5505HAE

HP LC to LC Multi-mode OM3 2-Fiber 5.0m 1-Pack Fiber Optic Cable AJ836A

HP Virtualized SAN NOTE: Optional iSCSI storage solutions, including the following.

HP P4300 G2 7.2TB SAS Starter SAN Solution BK716A

HP P4500 G2 14.4TB SAS Virtualization SAN Solution BQ888A

Factory Express HP Rack Signal Cable Interconnect Service

NOTE: Required selection when storage or switching is Factory integrated in the

same rack.

HA865A1

Step 5: Choose Additional Options for Factory Integration

Power Distribution Units NOTE: PDUs must be ordered in pairs for AC Feed redundancy.

HP Monitored Power Distribution Units

HP 17.3kVA 48A Single Input Three Phase NA/JP Monitored Power Distribution Unit AF916A

HP 7.3kVA 32A Single Input Three Phase INTL Intelligent Modular Power Distribution

Unit

AF536A

HP 22kVA 32A Single Input Three Phase INTL Monitored Power Distribution Unit AF917A

Modular PDUs 1U/0U (Up to 28 outlets)

NOTE: 1U/0U mounting brackets shipped with the unit (optimized for 10000 G2 and

9000 series racks).

HP 17.3kVA 48A Three Phase NA/JP Modular Power Distribution Unit AF511A





HP 22kVA 32A Three Phase INTL Core Modular Power Distribution Unit AF518A

HP 8.6kVA 24A Three Phase NA/JP Modular Power Distribution Unit AF512A

HP 11kVA 16A Three Phase INTL Modular Power Distribution Unit AF513A

HP 8.3kVA 40A High Voltage NA/JP Core Modular Power Distribution Unit 252663-D75

HP 9.2kVA 40A High Voltage INTL Core Modular Power Distribution Unit 252663-B34

HP 7.3kVA 32A High Voltage INTL Core Modular Power Distribution Unit 252663-B33

HP 4.9kVA 24A High Voltage NA/JP Core Modular Power Distribution Unit 252663-D74

NOTE: The Core Only Modular Power Distribution Unit Kits excludes the extension

bars as they are not required with the HP BladeSystem.

HP Two C13 PDU Extension Bar AF500A

NOTE: Each extension bar has a C19 input and 7 C13 receptacles. The option is ideal

for model S348, and, model S332, which both have only C19 outlets (12) and for all

Core Only Modular PDUs.

HP PCI expansion blades HP BLc PCI Expansion Blade 448018-B21


information:


(Worldwide)

HP BL c-Class PCI Express Mezzanine Pass Thru Option Kit 431643-B21

Signal Cables Optical Cables








NOTE: For VC Ethernet 10Gb uplinks

NOTE: For VC Fibre Channel uplinks

NOTE: For NC550SFP 10Gb dual port NIC uplinks in the Matrix CMS

NOTE: Optical transceivers/SFP+ must be purchased to connect these cables.

HP 10Gb SFP+ Copper cables

HP BladeSystem c-Class 10GbE SFP+ to SFP+ 0.5m Direct Attach Copper Cable 487649-B21

HP BladeSystem c-Class 10GbE SFP+ to SFP+ 1m Direct Attach Copper Cable 487652-B21




NOTE: For VC stacking between enclosures. 2 short links per Expansion kit, and 2

long links per Matrix rack (i.e. VC domain) is recommended.

NOTE: For VC Ethernet module uplinks (if Ethernet switch supports this uplink)

NOTE: For NC550SFP 10Gb dual port NIC uplinks in the Matrix CMS (if Ethernet switch

supports this uplink)

1Gb Ethernet (CAT5e) cables





HP 1.2m/4ft CAT5 RJ45 M/M Ethernet Cable C7533A

HP RJ45 to RJ45 Cat5e Black M/M 7.6m 1-pack Data Cable C7535A



HP 15.2m/50ft CAT5 RJ45 M/M Ethernet Cable

NOTE: For OA/iLO port uplinks to Ethernet switch (2 for each BladeSystem c7000

Enclosure, 1 for each Matrix CMS SKU or HP ProLiant DL server)

C7542A

NOTE: For OA enclosure linking (1 short link per Expansion Kit recommended).

NOTE: For OA/iLO port uplinks to Ethernet switch (2 for each BladeSystem c7000

Enclosure, 1 for each Matrix CMS SKU or HP ProLiant DL server).

NOTE: For 1Gb NIC uplinks to Matrix CMS SKU (optional, up to 4).

NOTE: For iSCSI device uplinks when present.

Power cords HP C19 - C20 Jumper Cords

NOTE: Default power cord is a 6ft IEC C19 - C20 cord

HP C19 - C20 WW 250V 16Amp Flint Gray 1.20m Jumper Cord AF575A

HP C19 - C20 WW 250V 16Amp Flint Gray 2.0m Jumper Cord AF574A

HP C19 - C20 WW 250V 16Amp 2.5m Jumper Cord 295633-B22

HP C19 - C20 WW 250V 16Amp 4.5m Jumper Cord E7804A

HP HV Power Cords 200 - 240V AC

HP C19 -Nema L6-30P US/CA 250V 16Amp 4.5m Power Cord E7805A

HP C19 - Nema L6-20P NA/JP 250V 20Amp High Voltage 3.6m Power Cord AF593A

HP C19 - NBR-14136 BR 250V 16Amp 2.5m Power Cord AF592A

HP C19 - BS-1363/A UK/HK/SG 250V 13Amp 3.6m Power Cord 359615-031

HP C19 - CEE-VII EU 250V 16Amp 3.6m Power Cord AF576A

HP C19 - AS3112-3 AU/NZ 250V 15Amp 3.6m Power Cord AF577A

HP C19 - SABS-164 ZA 250V 16Amp 3.6m Power Cord AF579A

HP C19 - CEI-23-50 IT/CL 250V 16Amp 3.6m Power Cord AF580A

HP C19 - IEC-309 DK/SE/AR 250V 16Amp 3.6m Power Cord AF581A

HP C19 - IS-1293 IN/PK/BD 250V 16Amp 2.5m Power Cord AF582A

HP C19 - ISI-32 IL 250V 16Amp 2.5m Power Cord AF583A

HP C19 - GB-1002 CN 250V 16Amp 2.5m Power Cord AF584A

HP C19 - CNS-690 TW 250V 16Amp 2.5m Power Cord AF585A

HP 240 VAC 4.5M Unterminated End NA Power Cord E7806A

Uninterruptible Power

Systems

HP Rack Mounted R5500 UPS (single-phase)

HP R5500 6000VA INTL 3U Rackmount Uninterruptible Power System AF416A

HP R5500 5000kVA NA/JP 3U Rackmount Uninterruptible Power System AF426A

NOTE: For more information on the R5500 please consult the QuickSpecs at:


(Worldwide)

HP Rack Mounted R8000 UPS (3-phase UPS)

HP R8000/3 8000kVA Three Phase NA 6U Rackmount Uninterruptible Power System AF431A

HP R8000/3 8000kVA Three Phase INTL 6U Rackmount Uninterruptible Power AF432A





System

HP Rack Mounted R12000 UPS (3-phase UPS)

HP R12000/3 12000VA Three Phase NA 6U Rackmount Uninterruptible Power

System

AF429A

HP R12000/3 12000VA Three Phase INTL 6U Rackmount Uninterruptible Power

System

AF430A

NOTE: For more information on the HP 3-Phase UPS products please consult the

QuickSpecs at:


(Worldwide)



Additional Options


HP Rack Series HP Intelligent Series Rack










information:


(Worldwide)

NOTE: For additional information regarding Rack Cabinets, please see the following


HP Rack Options Keyboards and Monitors

HP TFT7600 Rackmount Keyboard 17in US Monitor AG052A

HP TFT7600 Rackmount Keyboard 17in UK Monitor AG053A

HP TFT7600 Rackmount Keyboard 17in FR Monitor AG055A

HP TFT7600 Rackmount Keyboard 17in ES Monitor AG057A

HP TFT7600 Rackmount Keyboard 17in DK Monitor AG058A

HP TFT7600 Rackmount Keyboard 17in NO Monitor AG059A

HP TFT7600 Rackmount Keyboard 17in CH Monitor AG061A

HP TFT7600 Rackmount Keyboard 17in BE Monitor AG063A

HP TFT7600 Rackmount Keyboard 17in RU Monitor AG065A

HP TFT7600 Rackmount Keyboard 17in Intl Monitor AG066A

HP 1U US Rackmount Keyboard with USB AG072A

HP 1U UK Rackmount Keyboard with USB AG073A

HP 1U DE Rackmount Keyboard with USB AG074A

HP 1U FR Rackmount Keyboard with USB AG075A

HP 1U IT Rackmount Keyboard with USB AG076A

HP 1U ES Rackmount Keyboard with USB AG077A

HP 1U DK Rackmount Keyboard with USB AG078A

HP 1U NO Rackmount Keyboard with USB AG079A

HP 1U SE/FI Rackmount Keyboard with USB AG080A

HP 1U Rackmount Keyboard with USB AG081A

HP 1U PT Rackmount Keyboard with USB AG082A

HP 1U BE Rackmount Keyboard with USB AG083A

HP 1U JP Rackmount Keyboard with USB AG084A



Additional Options


HP 1U RU Rackmount Keyboard with USB AG085A

HP 1U INT Rackmount Keyboard with USB AG086A

NOTE: For additional information regarding Rack Options, please see the following

URL: http://www.hp.com/go/rackandpower

HP KVM Switch Options

HP 1-pack PS/2 Virtual Media Interface Adapter

NOTE: Requires PS/2 and one USB port on server.

AF604A

HP BladeSystem c-Class KVM Interface Adapter AF605A

HP Server Console 0x2x8 Port Analog Switch AF616A

HP Server Console 0x2x16 Port Analog Switch AF617A

HP KVM CAT5 1-pack PS/2 Interface Adapter 262588-B21

HP KVM CAT5 8-pack PS/2 Interface Adapter 262587-B21

NOTE: Cat5e cables are required to connect Interface Adapters to Consoles

Switches. Cat52 cables can be found at the following URL:

http://www.hp.com/go/kvm

HP 1x4 USB/PS2 KVM Console Switch AF611A

HP 1x4 KVM Console 6ft PS2 Cable AF612A

HP 1x4 KVM Console 6ft USB Cable

NOTE: required for supporting USB peripherals.

AF613A

NOTE: For additional information regarding KVM switches, Serial Console servers,

rack mount monitors, keyboards and all related options please see the following

URL: http://www.hp.com/go/kvm

NOTE: Cat5e cables are required to connect Serial Adapters to Serial Console

Servers. Additional Serial Adapters and Cat5e cables can be found at the following

URL: http://www.hp.com/go/kvm.

NOTE: For additional information regarding KVM switches, Serial Console servers,

rack mount monitors, keyboards and all related options please see the following

URL: http://www.hp.com/go/kvm.

Rack options for HP 10000 G2 Series racks

HP Universal 10636 G2 Front Door AF019A

HP 10K G2 600W Graphite Stabilizer Kit AF062A

HP 10K G2 600W Heavy Duty Graphite Stabilizer Kit AF064A

Rack options for HP Intelligent Series racks

HP Rack Grounding Kit BW891A

HP Rack Baying Kit BW902A

HP 42U 1075mm Side Panel Kit BW906A

HP 600m Rack Tie Down Kit BW926A

HP 600mm Rack Stabilizer Kit BW932A

HP 42U Front Door Kit BW934A

HP Quarter Turn Hook and Loop 10 Pack Kit BW963A


Rack options for HP Intelligent Series racks



Additional Options


HP Rack Grounding Kit BW891A

HP Rack Baying Kit BW902A

HP 600m Rack Tie Down Kit BW926A

HP 600mm Rack Stabilizer Kit BW932A

HP 42U Front Door Kit BW934A



NOTE: For additional information regarding Rack Options, please see the following


HP Airflow Optimization

HP Rack Airflow Optimization Kit AF090A

NOTE: The Airflow Optimization kit is designed to prevent hot and cold air from

mixing thus optimizing the temperature at which the chilled air enters the racked

servers.

NOTE: When configuring racks through Factory Express, a Rack Optimization kit will

automatically ship with the rack. This kit is recommended for all other rack

configurations also.

HP Matrix OE Public Cloud

Managed Instance

License

HP Matrix Operating Environment Public Cloud Managed Instance 1 year 24x7

Support License

BD580A


Support E-LTU

BD580AAE


Support Flexible License

BD581A

NOTE: Each traditional (node-based) Matrix OE license includes rights to also

manage one public cloud instance. For example, a purchase of 16 Matrix OE server

licenses entitles the buyer to also manage up to 16 instances concurrently across all

public clouds. This built-in public cloud licensing may be sufficient to cover all

bursting needs of some CloudSystem users. If more extensive bursting is required, a

Matrix OE public cloud managed instance license (BD580A, BD580AAE, and BD581A)

is required for each additional VM that will be managed concurrently on public cloud

infrastructure.

NOTE: Customers purchasing "t" quantity of the traditional (node-based) Matrix OE

license and "p" quantity of the Matrix OE Public Cloud Managed Instance License will

be able to burst up to "t+p" virtual machine(s) concurrently. The total number of

VMs in use simultaneously across all cloud service providers may not exceed "t+p".

NOTE: The Matrix OE Public Cloud Managed Instance License (BD580A, BD580AAE,

and BD581A) will be valid for a period of one year from the date of purchase. To

extend rights to manage a public cloud instance beyond the license term, customers

must purchase another license when their current license expires.

NOTE: For each purchased fixed or flexible license, a printed license entitlement

certificate will be delivered. For each purchased electronic license, a license

entitlement certificate will be delivered electronically.

HP Care Pack services NOTE: HP Care Pack services for the BladeSystem c7000 enclosure cover the

enclosure, power supplies and fans. HP qualified rack options are covered by these



Additional Options


services when installed within the same rack. HP supported BladeSystem c-Class

enclosure devices including pass thru, Ethernet interconnect and virtual connect

modules are also covered by the BladeSystem c7000 enclosure Care Pack services.

NOTE: SAN/Fabric switches for the HP BladeSystem c-Class enclosure are not

covered under the BladeSystem c7000 enclosure Care Packs, SAN/Fabric switches

carry separate Care Packs. SAN/Fabric Switch Care Pack service level support should

always be uplifted to match existing storage or server service level.

Hardware Services On-site Service

HP 3 year Next business day c7000 Enclosure Hardware Support

NOTE: Uplifts the Ethernet devices to the same level of service as the c-class

enclosure.

UE477E

HP 3 year 4 hour 13x5 c7000 Enclosure Hardware Support UE478E

HP 3 year 4 hour 24x7 c7000 Enclosure Hardware Support UE479E

HP 3 year 6 hour 24x7 Call to Repair c7000 Enclosure Hardware Support UE480E


HP 3 Years Next business day c-Class SAN Switch Hardware Support UE436E

HP 3 Years 4 hour 13x5 c-Class SAN Switch Hardware Support UE437E

HP 3 Years 4 Hour 24 hours UE438E

HP 3 Years 6 Hour 24x7 Call-To-Repair c-Class SAN Switch Hardware Support UE439E

HP Installation Storage Switches Service U5988E

Software Operating Environment Care Packs

HP 1 year Software Technical Support 10 incidents 24x7 Microsoft Software Support U9269E

HP 1 year 24x7 25 incident Red Hat High Performance Computing Software Technical

Support

U3408E

HP 1 year 24x7 10 incidents SuSE IA32 Software Technical Support U9936E

NOTE: For more information, customer/resellers can contact:

http://www.hp.com/go/carepack

NOTE: SAN/Fabric switches for the HP BladeSystem c-Class enclosure are not

covered under the BladeSystem c7000 enclosure Care Packs, SAN/Fabric switches

carry separate Care Packs. SAN/Fabric Switch Care Pack service level support should

always be uplifted to match existing storage or server service level.


Next Business Day On-site Service, 5-Day x 9-Hour Coverage, 3 Years, Electronic

NOTE: Uplifts the Ethernet devices to the same level of service as the c-class

enclosure.

HA101A3#6Q6

4-Hour On-site Service, 5-Day x 13-Hour Coverage, 3 Years, Electronic HA103A3#6Q6

4-Hour On-site Service, 7-Day x 24-Hour Coverage, 3 Years, Electronic HA104A3#6Q6

6-Hour Call to Repair, On-site Service, 7-Day x 24-Hour Coverage, 3 Years, Electronic HA105A3#6Q6

Support Plus

Support Plus Service, 5-Day x 13-Hour Coverage HA109A3#6Q6

Support Plus 24

Support Plus 24 Service HA110A3#6Q6



Additional Options


Proactive 24 Service - Mission Critical proactive environment 24x7 4hr onsite HW

support

HA111A3#6Q6

Critical Service - Mission Critical proactive environment 6-Hour Call-to-Repair onsite

HW support

HA112A3#6Q6

Hardware Installation, Electronic HA113A1#5D2

Infrastructure Software On-site Services

HP Startup Insight Dynamics Recovery Management Service

NOTE: Disaster Recovery requires both a Primary Site and Secondary Site, and

supported HP SAN Storage at both sites to have "Continuous Access" implemented

between the SAN.

NOTE: All HP CloudSystem Matrix infrastructure ships with licensed disaster recovery

protection for both physical and virtual servers, in coordination with data replication

provided by EVA or XP Continuous Access software. Disaster recovery protection can

be achieved by implementing a secondary infrastructure at a remote location, and

enabling storage replication between the two sites.

UK830E

HP Matrix Operating Environment Recovery Management Installation & Startup

Service, Flexible

HA124A1#5FX

HP CloudSystem Upgrade (same CMS) Implementation Service HA115A1#5PA

NOTE: This is a required Service to upgrade your Matrix environment to a later

version.

NOTE: This service performs an upgrade to the Matrix environment using the existing

Matrix HP SIM Central Management Server.

HP Implementation service for the CloudSystem Matrix Upgrade UU960E

HP CloudSystem Upgrade (different CMS) Implementation Service HA115A1#5PB

NOTE: This is a required Service to upgrade your Matrix environment to a later

version.

NOTE: This service performs an upgrade to the Matrix environment using requiring a

different Matrix HP SIM Central Management Server (includes migrating data from

the existing CMS to the new CMS).

HP Implementation service for the CloudSystem Matrix Upgrade with Migration UU961E

HP CloudSystem Expansion Kit Integration Implementation Service HA115A1#5P9

NOTE: This is a required Service to expand your existing Matrix environment by

adding Matrix Expansion Kits.

HP Hardware Install c-Class Enclosure and Server Blade Service

NOTE: This is recommended to assist with onsite racking and cabling of CloudSystem

Matrix enclosures into a rack, particularly when CloudSystem Matrix kits are

purchased without a rack.

UE494E

HP Install c7000 Enclosure and Server Build Service, Flexible

NOTE: This is recommended to assist with onsite racking and cabling of CloudSystem

Matrix enclosures into a rack, particularly when CloudSystem Matrix kits are

purchased without a rack.

HA113A1#5FY

HP Additional Technical Assistance

NOTE: This service provides the capability to customize tasks and activities including

assistance with design, implementation, migration, and project management.

HA334A1

NOTE: HP recommends the client purchase the optional 13 education credits (SKU#



Additional Options


HF385E or HF385A1) found on every Matrix quote. Specific training

recommendations for a given client will vary depending on the customer's existing

knowledge and experience.

c-class BladeSystem administration (For customers new to ProLiant blades) HE646S

HP Insight Control: Management Fundamentals HK756S

HP Virtual Connect HK758S

HP Matrix OE: Infrastructure Administration HK920S

HP Insight Control: Management Master HK757S

HP Integrity Virtual Machines (Integrity Installations) HB506S

Managing 3PAR Disk Arrays (3 PAR installations) HK902S

HP Care Pack Service for ProLiant Training HF385E



Power Specifications


Half-height server blade bay numbering

1. Device Bay 1 9. Device Bay 9








NOTE: Half-height servers should be populated from top and bottom from left to right (looking at the front of the enclosure). So

the first two half-height servers would be placed in bays 1 & 9 the second two half-height servers would be placed in bays 2 & 10

and so on until the enclosure is full.

Full-height server blade bay numbering









NOTE: Full-height servers should be populated from left to right.

Mixed Configuration - Full Height and Half-Height Population rules

The BladeSystem c7000 enclosure is divided into 4 zones by the vertical support metalwork. Within each zone a removable divider

is used to support half height devices. To install a full-height blade in any zone this divider must be removed. As a consequence a

zone can only contain either full-height server blades or half-height server blades.

NOTE: Storage blades and tape blades can be installed in the same zone as both full-height and half-height server blades, a

bracket ships with each SB40c tape blade that allows a half-height blade to be mounted on top of the tape blade.

NOTE: The lower tape or storage blade cannot be removed without first removing the upper half-height blade.

HP BladeSystem

c7000 enclosure

Dimensions Height 17.4 in (442 mm)

Width 17.6 in (447.04 mm)

Depth 32 in (813 mm)

Shipping dimensions Height 29.88 in (759 mm)

Width 23.88 in (607 mm)

Depth 39.88 in (1013 mm)

Single-phase enclosure

weight

Unboxed 192 lb (87 kg)

Shipping 235 lb (106.6 kg)

Three -phase enclosure

NA/JPN weight

Unboxed 222 lb (100.7 kg)


Three-phase enclosure

international weight



DC input enclosure

weight


Shipping 194 lb (88 kg)

Maximum enclosure

weight (approximate)

Unboxed 450 lb (204 kg)






Temperature range Operating 50° to 95° F (10° to 35° C)

Non-Operating -22° to 140° F (-30° to 60° C)

Relative humidity Operating 10 to 90% relative humidity (Rh), 28°C (82.4°F)

maximum wet bulb temperature, non-

condensing.

Non-Operating 5 to 95% relative humidity (Rh), 38.7°C

(101.7°F)maximum wet bulb temperature, non-

condensing.

NOTE: Operating temperature has an altitude derating of 1.8° F (1° C) per 1,000 ft (304.8 m). No direct

sunlight. Upper operating limit is 10,000 ft (3,048 m) or 70Kpa/10.1 psia. Upper non-operating limit is

30,000 ft (9,144 m) or 30.3 KPa/4.4 psia. Storage maximum humidity of 95% is based on a maximum

temperature of 113° F (45° C). Altitude maximum for storage is 70 KPa.

Power Input requirements -

single-phase model

Rated input frequency 50 to 60 Hz

2250W PSU Rated input voltage 100 to 120 VAC

200 to 240 VAC

Rated input current

per power supply

12.3A at 100 - 120

VAC

13.1 A at 200 VAC

12.6 A at 208 VAC

11.9 A at 220 VAC

Rated input power

per power supply

2612 VA Max

2400W PSU Rated input voltage 200 to 240 VAC

Rated input current

per power supply

13.9 A at 200 VAC

13.3 A at 208 VAC

12.6 A at 220 VAC

Rated input power

per power supply

2780 VA

Power cords Single-Phase IEC-320 C19-C20 1.22m (6 ft)

3-Phase NA/JPN 2 x NEMA L15-30p 2.44m (10 ft)

3-Phase International 2 x IEC-309 200/346 V - 240/415 V, 5-Pin, 6h

16A 2.44m (10 ft)

-48V DC Power Terminal lug: 45DG 4AWG 1/4 2H

Two-hole lug

45 degree bend

0.25in. (6.4mm) stud hole size

0.63in. (16mm) hole spacing

Output

specifications

(per power supply)

HP 2250W Hot-Plug

Power Supply

200 - 240 VAC 2250 W

100 - 120 VAC 960 W

HP 2400W High Efficiency

Hot-Plug Power Supply

200 - 240 VAC 2400 W

HP 2250W -48V DC Hot-

Plug Power Supply

2250W





Acoustic noise Listed are the declared A-Weighted sound power levels (LWAd) and

declared average bystander position A-Weighted sound pressure levels

(LpAm) when the product is operating in a 23°C ambient environment.

Noise emissions were measured in accordance with ISO 7779 (ECMA 74) and

declared in accordance with ISO 9296 (ECMA 109).

Idle

LWAd 7.5 Bels

LpAm 57 dB

Idle

LWAd 7.5 Bels

LpAm 57 dB

Environmental-friendly

products and approach

End-of-life management

and recycling

Hewlett-Packard offers end-of-life HP product return, trade-in, and

recycling programs in many geographic areas. For trade-in information,

please go to: http://www.hp.com/go/green. To recycle your product,

please go to: http://www.hp.com/go/green or contact your nearest HP

sales office. Products returned to HP will be recycled, recovered or

disposed of in a responsible manner.

The EU WEEE directive (2002/95/EC) requires manufacturers to provide

treatment information for each product type for use by treatment

facilities. This information (product disassembly instructions) is posted on

the Hewlett Packard web site at: http://www.hp.com/go/green. These

instructions may be used by recyclers and other WEEE treatment facilities

as well as HP OEM customers who integrate and re-sell HP equipment.

NOTE: To review maximum system power ratings for facilities planning purposes use the Active Answers Power Calculator which

is available via the online tool located at URL: http://www.hp.com/go/bladesystem/powercalculator



Summary of Changes


Date Version History Action Description of Change:

24-Jun-2016 From Version 35 to 36 Retire Document Retired

06-Mar-2015 From Version 34 to 35 Added Added the new CMS

13-Oct-2014 From Version 33 to 34 Changed Changed the What´s New Section and Update some SKU

Descriptions.

16-May-2014 From Version 32 to 33 Changed Product descriptions were revised throughout Ordering

CloudSystem Matrix

20-Dec-2013 From Version 31 to 32 Changed Changes made to What's New and in the Additional Options

section.

28-Jun-2013 From Version 30 to 31 Changed Two part numbers were changed in Step 2.

25-Mar-2013 From Version 29 to 30 Changed Overview: Completely updated What's new section.

Ordering CloudSystem Matrix: Updated KVM Management

Sever and KVM Managed Host sections.

09-Nov-2012 From Version 27 to 28 Changed Changes were made in Ordering CloudSystem Matrix section.

14-Sep-2012 From Version 26 to 27 Changed Changes were made in Cloud System Matrix and Additional

Options sections.

17-Aug-2012 From Version 25 to 26 Changed Changes made in the Ordering CloudSystem Matrix and

Additional Options sections.

13-Aug-2012 From Version 24 to 25 Changed Changes made throughout the QuickSpec.

12-Jun-2012 From Version 23 to 24 Removed Removed a bullet from the What's New section.

08-Jun-2012 From Version 22 to 23 Changed Changes made within the Overview and Ordering CloudSystem

Matrix sections.

04-Jun-2012 From Version 21 to 22 Changed Changes made throughout the QuickSpec.

20-Apr-2012 From Version 20 to 21 Changed Changes made in the CloudSystem System Matrix,

Configuration Information and Additional Options sections.

06-Apr-2012 From Version 18 to 20 Changed BladeSystem was changed to CloudSystem.

06-Mar-2012 From Version 17 to 18 Changed Changes were made throughout the QuickSpec.

30-Aug-2011 From Version 16 to 17 Changed Changes were made throughout Ordering Information and to

HP Rack Options and HP Care Pack services in Additional

Options

Mentions of Cloud Service Automation for Matrix were added

20-Jun-2011 From Version 15 to 16 Changed Revisions were made throughout changing BladeSystem to

CloudSystem.

05-Apr-2011 From Version 14 to 15 Added HP BladeSystem Matrix Conversion Services, HP BladeSystem

Matrix - Extended Infrastructure and HP Utility Ready

Computing on Matrix were added to HP BladeSystem Matrix

HP NC553m 10Gb 2-port FlexFabric Adapter was added to HP

Ethernet Mezzanine Options

Changed Updated to version 6.3

HP Uninterruptible Power Systems product descriptions were

revised



Summary of Changes


14-Jan-2011 From Version 13 to 14 Changed Changes made within the Ordering BladeSystem Matrix.

16-Nov-2010 From Version 12 to 13 Changed Edits were made within Ordering BladeSystem Matrix including

revising product descriptions and updating HP Interconnects

notes

HP Rack Series was completely revised

05-Oct-2010 From Version 11 to 12 Changed How to order HP BladeSystem Matrix and Warranty Services

were revised in HP BladeSystem Matrix

Virtual to physical was added to Availability and proactive

support and Storage LUN configuration and

presentation/zoning (with purchase of EVA4400) was removed

from Orchestrated provisioning of services in HP BladeSystem

Matrix Infrastructure Operating Environment

Ordering BladeSystem Matrix and HP Care Pack Services were

completely revised

Part numbers were modified in HP Rack Series

Matrix Starter Kit and Matrix Expansion Kits (included in the

Starter Kit order) was added to HP BladeSystem Matrix Starter

Kit Implementation Service

HP BladeSystem Matrix Expansion Kit Integration

Implementation Service was added to HP BladeSystem Matrix

Tape Storage was removed from Additional Options

12-Jul-2010 From Version 10 to 11 Removed Removed duplicate text.

09-Jul-2010 From Version 9 to 10 Changed Descriptions for part numbers 500662-B21 and 418367-B21

were revised for BladeSystem c-Class server blades chart in

Ordering BladeSystem Matrix

HP BladeSystem c7000 enclosure descriptions were revised in

Technical Specifications

Removed HP 16A 250V IRAM 2073/IEC320-C19 2.5m/8ft was removed

from Power Cords

2x1x16 and 4x1x16 IP Console Switches with Virtual Media and

2x16 Server Console Switch with Virtual Media were removed

from HP Rack Options

HP StorageWorks Virtual Library Systems were removed from

Tape Storage

30-Apr-2010 From Version 8 to 9 Changed Revisions were made throughout Ordering BladeSystem

Matrix.

29-Mar-2010 From Version 7 to 8 Changed Part number for HP BladeSystem Matrix Starter Kit - HP Insight



Summary of Changes


Software was changed in Step 2

Central management server (CMS), recommended default SKU

was completely revised and Part number was added in Step 2

Microsoft Windows Server 2008 with Hyper-V licenses were

revised in Step 3

NOTE was added to callout 6 for the Starter Kit Overview

image

12-Feb-2010 From Version 6 to 7 Changed Changes made throughout the QuickSpec.

04-Dec-2009 From Version 5 to 6 Changed Changes made throughout the QuickSpec.

04-Sep-2009 From Version 4 to 5 Changed Changes made throughout the entire QuickSpec except for the

Technical Specifications section.

12-Jun-2009 From Version 3 to 4 Added HP BladeSystem Matrix Orchestration throughout the HP

BladeSystem Matrix section

NOTEs and VC Flex-10 10Gb Ethernet module transceiver/SFP

options to HP BladeSystem Matrix Starter Kit and Expansion

Kit in the Ordering BladeSystem Matrix section

Changed Updated BladeSystem c-Class server blades and HP

StorageWorks EVA4400 in the Ordering BladeSystem Matrix

section

29-May-2009 From Version 2 to 3 Added What's New to the Overview section

HP BladeSystem Matrix Starter Kit - Implementation Service,

Fixed and Flexible to HP BladeSystem Matrix Starter Kit in the

Ordering BladeSystem Matrix section

4 year and 5 year, 24x7 4hr BladeSystem Matrix Starter

Hardware Support, Fixed and Flexible to Support Plus 24

options for BladeSystem Matrix Starter Kit in the Ordering


4 year and 5 year 24x7 BL Matrix Software Support, Fixed and

Flexible to Support Plus 24 options for BladeSystem Matrix

Starter Kit in the Ordering BladeSystem Matrix section

4 year and 5 year Support Plus 24 BLc Matrix Expansion Kit

Support, Fixed and Flexible to Support Plus 24 options for the

entire BladeSystem Matrix Expansion Kit in the Ordering


HP Insight Recovery Installation & Startup Service, Flexible to

Service and Support offerings in the Additional Options section

01-May-2009 From Version 1 to 2 Changed Other changes made throughout the QuickSpec including a

complete revision of the Ordering BladeSystem Matrix section.



Summary of Changes


© Copyright 2016 Hewlett-Packard Development Company, L.P.

The information contained herein is subject to change without notice.

Microsoft and Windows are US registered trademarks of Microsoft Corporation.

Intel, the Intel logo, Xeon and Xeon Inside are trademarks of Intel Corporation in the U.S. and other countries.

AMD Opteron™ is a US registered trademark of AMD Corporation.

The only warranties for HP products and services are set forth in the express warranty statements accompanying such products

and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or

editorial errors or omissions contained herein.


Documents

RETIRED: Retired products sold prior to the November 1 ... · x Ability to change disk size and user -defined properties at time of service creation ... QuickSpecs HP CloudSystem