THIRD ANGLE PROJECTION

8±.020" SLIDE LENGTH 8±.118" SLIDE TRAVEL

SCALE: 1:3 SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD FLAT HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 6/27/2018 NS2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/4/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-8PART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 8" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008

3.252±.016

4.252±.016

.622±.008

2.252±.012

1.000±.008 2X .327±.020 X .248±.020 90 INSIDE

3X .220±.020 90 INSIDE

.252±.008

3X .205±.008

.413±.008

.752±.008

.752±.008

1.500±.012

2.000±.012 2.500±.012

3.071±.012

.748±.008

3X .374±.008 X .205±.008

1.252±.012

1.500±.012

.181±.008 X .205±.008

.205±.008 X .453±.008

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-8PART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 8" SLIDE

KCHEN 2SCALE: 1:2

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

10±.118" SLIDE TRAVEL 10±.020" SLIDE LENGTH

SCALE: 1:4

SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 6/28/2018 NS2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/4/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-10-QDPART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 10" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2017

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008

.252±.008

3.252±.016 6.252±.016

.622±.008

8.504±.020

3X .256±.008

1.000±.008

2X .362±.008 X .276±.008

3X .205±.008 .413±.008

.752±.008

1.252±.039

.752±.008

1.500±.012

2.000±.012

2.500±.012

.752±.008

5.071±.016

.748±.008

3X .374±.008 X .205±.008.205±.008 X .453±.008

.181±.008 X .205±.008

OBSTRUCTED NON-FUNCTIONAL

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-10-QDPART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 10" SLIDE

KCHEN 2SCALE: 1:3

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2017

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

13±.118" SLIDE TRAVEL 12±.020" SLIDE LENGTH

SCALE: 1:4SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 6/28/2018 NS2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/4/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-12-QDPART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 12" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008

.252±.008

3.252±.016

8.252±.020

.622±.008

10.504±.020

3X .256±.008

1.000±.008

2X .362±.008 X .276±.008

3X .205±.008 .413±.008

.752±.008

1.252±.039

.752±.008

1.500±.012 2.000±.012 2.500±.012

.752±.008

7.063±.016

.748±.008

3X .374±.008 X.205±.008

.181±.008 X .205±.008

.205±.008 X .453±.008

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-12-QDPART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 12" SLIDE

KCHEN 2SCALE: 1:4

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

15±.118" SLIDE TRAVEL 14±.020" SLIDE LENGTH

SCALE: 1:4SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 6/28/2018 NS2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/4/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-14-QDPART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 14" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008

.252±.008

3.252±.016 10.252±.020

.622±.008

12.504±.020

3X .256±.008

1.000±.008

2X .362±.008 X .276±.008

3X .205±.008 .413±.008

.752±.008

1.252±.039

.752±.008

1.500±.012

2.000±.012

2.500±.012

.752±.008

9.063±.020

.748±.008

3X .374±.008 X.205±.008

.205±.008 X .453±.008

.181±.008 X .205±.008

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-14-QDPART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 14" SLIDE

KCHEN 2SCALE: 1:4

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

17±.118" SLIDE TRAVEL 16±.020" SLIDE LENGTH

SCALE: 1:6SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 6/28/2018 NS2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/4/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-16-QDPART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 16" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008

3X .256±.008

.252±.008 1.000±.008 3.252±.016

12.252±.020

.622±.008

14.504±.020

2X .362±.008 X .276±.008

3X .205±.008 .413±.008

.752±.008

1.252±.039

.752±.008

1.500±.012

2.000±.012

2.500±.012

1.000±.008

.752±.008

11.063±.020

.748±.008

4X .374±.008 X.205±.008

.181±.008 X .205±.008

.205±.008 X .453±.008

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-16-QDPART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 16" SLIDE

KCHEN 2SCALE: 1:4

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

19±.118" SLIDE TRAVEL 18±.020" SLIDE LENGTH

SCALE: 1:6

SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 6/28/2018 NS2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/4/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-18-QDPART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 18" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008 3X .256±.008

.252±.008 1.000±.008

3.252±.016 14.252±.020

.622±.008

16.504±.020

2X .362±.008 X .276±.008

4X .205±.008 .413±.008

.752±.008

1.252±.039

.752±.008

1.500±.012 2.000±.012 2.500±.012

5.000±.016

1.000±.008

.752±.008

13.063±.020

.748±.008

4X .374±.008 X.205±.008

.181±.008 X .205±.008

.205±.008 X .453±.008

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-18-QDPART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 18" SLIDE

KCHEN 2SCALE: 1:4

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

21±.118" SLIDE TRAVEL 20±.024" SLIDE LENGTH

SCALE: 1:10

SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 6/28/2018 NS2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/4/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-20-QDPART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 20" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2017

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008

3X .256±.008

.252±.008 1.000±.008

3.252±.016 16.252±.020

.622±.008

18.504±.020

2X .362±.008 X .276±.008

5X .205±.008 .413±.008

.752±.008

1.252±.039

.752±.008

1.500±.012 2.000±.012

2.500±.012

5.000±.016

7.500±.020

1.000±.008

.752±.008

15.063±.020

.748±.008

4X .374±.008 X.205±.008

.181±.008 X .205±.008

.205±.008 X .453±.008

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-20-QDPART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 20" SLIDE

KCHEN 2SCALE: 1:4

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2017

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

23±.118" SLIDE TRAVEL 22±.024" SLIDE LENGTH

SCALE: 1:10

SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 6/28/2018 NS2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/4/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-22-QDPART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 22" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008

3X .256±.008

.252±.008 1.000±.008

3.252±.016 18.252±.020

.622±.008

20.504±.024

2X .362±.008 X .276±.008

5X .205±.008 .413±.008

.752±.008

1.252±.039

.752±.008

1.500±.012 2.000±.012

2.500±.012

5.000±.016 7.500±.020

1.000±.008

.752±.008

17.063±.020

.748±.008

13.563±.020

.181±.008 X .205±.008

.205±.008 X .453±.008

5X .374±.008 X .205±.008

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-22-QDPART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 22" SLIDE

KCHEN 2SCALE: 1:4

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

25±.118" SLIDE TRAVEL 24±.024" SLIDE LENGTH

SCALE: 1:10

SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 6/28/2018 NS2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/4/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-24-QDPART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 24" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008

3X .256±.008

.252±.008 1.000±.008 3.252±.016

20.252±.024

.622±.008

22.504±.024

2X .362±.008 X .276±.008

5X .205±.008 .413±.008

.752±.008

1.252±.039

.752±.008

1.500±.012

2.000±.012 2.500±.012

5.000±.016

7.500±.020

1.000±.008

.752±.008

19.063±.020

.748±.008

15.563±.020

.205±.008 X .453±.008

.181±.008 X .205±.0085X .374±.008 X .205±.008

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-24-QDPART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 24" SLIDE

KCHEN 2SCALE: 1:4

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

27±.118" SLIDE TRAVEL 26±.024" SLIDE LENGTH

SCALE: 1:10

SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 6/28/2018 NS2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/4/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-26-QDPART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 26" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008

3X .256±.008

.252±.008 1.000±.008

3.252±.016 22.252±.024

.622±.008

24.504±.024

2X .362±.008 X .276±.008

5X .205±.008 .413±.008

.752±.008

1.252±.039

.752±.008

1.500±.012 2.000±.012

2.500±.012

5.000±.016

7.500±.020

1.000±.008

.752±.008

21.063±.024

.748±.008

17.563±.020

.181±.008 X .205±.008

.205±.008 X .453±.0085X .374±.008 X .205±.008

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-26-QDPART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 26" SLIDE

KCHEN 2SCALE: 1:4

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

29±.118" SLIDE TRAVEL 28±.024" SLIDE LENGTH

SCALE: 1:10

SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 6/28/2018 NS2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/4/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-28-QDPART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 28" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008 4X .256±.008

.252±.008 1.000±.008 3.252±.016

9.752±.020 24.252±.024

.622±.008

26.504±.024

2X .362±.008 X .276±.008

5X .205±.008 .413±.008

.752±.008

1.252±.039

.752±.008

1.500±.012 2.000±.012 2.500±.012

5.000±.016 7.500±.020

1.000±.008

.752±.008

23.063±.024

.748±.008

19.563±.020

.205±.008 X .453±.008

.181±.008 X .205±.008

5X .374±.008 X .205±.008

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-28-QDPART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 28" SLIDE

KCHEN 2SCALE: 1:4

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

31±.118" SLIDE TRAVEL 30±.024" SLIDE LENGTH

SCALE: 1:10

SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 6/28/2018 NS2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/4/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-30-QDPART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 30" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008 4X .256±.008

.252±.008 1.000±.008

3.252±.016 11.752±.020

26.252±.024

.622±.008

28.504±.024

2X .362±.008 X .276±.008

5X .205±.008 .413±.008

.752±.008

1.252±.039

.752±.008

1.500±.012 2.000±.012

2.500±.012 5.000±.016

7.500±.020

1.000±.008

.752±.008

25.063±.024

.748±.008

21.563±.024

.205±.008 X .453±.008

.181±.008 X .205±.008

5X .374±.008 X .205±.008

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-30-QDPART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 30" SLIDE

KCHEN 2SCALE: 1:4

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

33±.118" SLIDE TRAVEL 32±.024" SLIDE LENGTH

SCALE: 1:10

SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD FLAT HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 6/28/2018 NS2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/4/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-32-QDPART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 32" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2017

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008

6X .220±.020 90 INSIDE

.252±.008 1.000±.008 3.252±.016

9.252±.020

16.502±.020 21.752±.024

28.252±.024

.622±.008

30.504±.024

2X .327±.020 X .248±.02090 INSIDE

5X .205±.008 .413±.008

.752±.008

1.252±.039

.752±.008

1.500±.012 2.000±.012

2.500±.012 5.000±.016

7.500±.020

1.000±.008

.752±.008

27.063±.024

.748±.008

23.563±.024

.181±.008 X .205±.008

.205±.008 X .453±.0085X .374±.008 X .205±.008

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-32-QDPART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 32" SLIDE

KCHEN 2SCALE: 1:4

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2017

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

35±.118" SLIDE TRAVEL 34±.024" SLIDE LENGTH

SCALE: 1:10

SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD FLAT HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 6/28/2018 NS2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/4/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-34-QDPART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 34" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008

6X .220±.020 90 INSIDE

.252±.008 1.000±.008

3.252±.016 9.252±.020

16.502±.020 23.752±.024

30.252±.024

.622±.008

32.504±.024

2X .327±.020 X .248±.02090 INSIDE

7X .205±.008 .413±.008

.752±.008

1.252±.039

.752±.008

1.500±.012 2.000±.012 2.500±.012 5.000±.016

7.500±.020

14.500±.020 20.504±.024

1.000±.008

.752±.008

29.063±.024

.748±.008

25.563±.024

.181±.008 X .205±.008

.205±.008 X .453±.0085X .374±.008 X .205±.008

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/4/2019

I-DS-2250-34-QDPART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 34" SLIDE

KCHEN 2SCALE: 1:4

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

37±.118" SLIDE TRAVEL 36±.024" SLIDE LENGTH

SCALE: 1:10

SCALE: 1:2

2.087+-.020.000

.752+-.028.000

RECOMMENDEDINNER SLIDE MEMBER:#10 MACHINE OR WOOD PAN HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

OUTER SLIDE MEMBER:#10 MACHINE OR WOOD FLAT HEAD SCREW FOR ALL THRU HOLES AND SLOTTED THRU HOLES

SIDE SPACE: PULL FORCE:.752 .028" 3 -7 LBS

REVISIONSREV. DESCRIPTION DATE BY

1 INITIAL RELEASE 1/14/2019 RGM2 UPDATE DIMENSIONS TO MATCH VENDOR'S PRINT 9/11/2019 KC

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/11/2019

I-DS-2250-36-QDPART NUMBER:

STEELMATERIAL:

SHEET 1 OF 2

2250 SERIES 36" SLIDE

KCHEN 2SCALE:

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1

THIRD ANGLE PROJECTION

.197±.008

6X .220±.020 90 INSIDE

.252±.008 1.000±.008 3.252±.016

9.252±.020 16.502±.020

25.752±.024 32.252±.024

.622±.008

34.504±.024

2X .327±.020 X .248±.02090 INSIDE

7X .205±.008 .413±.008

.752±.008

1.252±.039

.752±.008

1.500±.012 2.000±.012

2.500±.012 5.000±.016

7.500±.020 14.500±.020

20.504±.024 27.563±.024

1.000±.008

.752±.008

31.063±.024

.748±.008

5X .374±.008 X .205±.008.181±.008 X .205±.008

.205±.008 X .453±.008

UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN INCHES [mm]

.XX [.X] = 0.03 [0.8mm].XXX [.XX] = 0.015 [0.38mm]

.XXXX [.XXX] = 0.0080 [0.203mm]FRACTIONAL = 1/32"

ANGULAR: 1.0

QUALITY

DO NOT SCALE9/11/2019

I-DS-2250-36-QDPART NUMBER:

STEELMATERIAL:

SHEET 2 OF 2

2250 SERIES 36" SLIDE

KCHEN 2SCALE: 1:4

REV

ASIZE

NAMEDATE

ENGR SALES

ZINC PLATEDDESCRIPTION:

NOTES:DIMESIONS APPLY AFTER FINISH.1.DO NOT SCALE DRAWING.2.BREAK ALL SHARP EDGES AND REMOVE ALL BURRS.3.MUST HAVE NO SCRATCHES, DINGS, DENTS OR SURFACE IMPERFECTIONS OTHER THAN 4.SURFACE FINISH REQUIREMENTS.CRITICAL DIMENSIONS ARE INDICATED BY: 5.TO BE INSPECTED TO 2.5 AQL SAMPLING PLAN UNLESS OTHERWISE STATED.6.ENSURE PACKAGING WILL PROVIDE ADEQUATE PROTECTION DURING TRANSPORT. 7.GEOMETRIC FEATURES NOT DIMENSIONED ARE CONTROLLED BY 3D MODEL.8.

FINISH:

PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF RYADON INC. ANY REPRODUCTION

IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF RYADON INC. IS PROHIBITED.

BW12/19/2019

PN12/17/2019

A A

B B

C C

D D

6

6

5

5

4

4

3

3

2

2

1

1