RF wireless LED remote controller

Six zones/areasPress-button RGBW controller

Model:RGBRF-RC1 with RGBRF-4x5A

Parameter

Wiring diagram

Product Size

Brief introduction of buttons

Product introduction

Part No. Iuput Voltage RemarksCurrent

12-36VDC Constant voltage4x(60-180)W4x5A

Output

Remote

Part No. Operation Voltage DIMENSIONSø/h (mm)

Operation Frequency

3.6VDC 48x140x16434MHz/868MHz

Receiver

Remarks

load 3pcs 7 AAA (1.5V) batteries Note:

One receiver can work with 1-8pcs RGBRF-4x5A or 1pc RGBRF-4x5A

One RGBRF-RC1 can control multiple receiversThe power supply chosen must be 20% higher than the actual load

5 6

2 31

R G B

4

Indicator: indicate the state of remote control

White channel: the 4th channel

Touch color wheel

Pause/Run button: 10 modes built-in

R/G/B channels

ON/OFF of all zones

Speed down under dynamic mode

Return previous status button

Save button: save up to 6 colors or modes into 6 positions

(6-zone buttons)

6 zones: each zone can save 6 color or modes

Speed up under dynamic mode

Brightness: dim up

Brightness: dim down

1) Receiver Connection Diagram for Single Unit

2) Connection Diagram for Multiple Units Receiver

Power Supply12-36VDC L

N

110V-230VAC

whi

te

LED CONTROLLER

12

34

Learning Key

whi

te

LED CONTROLLER

12

34

Learning Key

whi

te

LED CONTROLLER

12

34

Learning Key

Power Supply12-36VDC L

N

110V-230VAC

whi

te

LED CONTROLLER

12

34

Learning Key

140.0

48.0

17.0

RGBRF-RC1 remote controller has 6 different zones. It can achieve Red/Green/Blue/White colour directly. The remote controller can save up to 6 colours or 6 modes via the corresponding buttons (1-6 positions) for each zone.You can choose any colour using the colour wheel. You can also set the system as RGB 3-channel output or RGBW 4-channel output.

RGBRF-RC1

RGBRF-4x5A

RGBRF-4x5A

RGBRF-4x5A

RGBRF-4x5A

and up to 7pcs PRDIM

RGBRF-4x5A

White (positive)

White (positive)

White (positive)

White (positive)

Safety & Warnings

Warranty Agreement

1) The product shall be installed and serviced by a qualified person.

2) IP20.Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water proof enclosure.

3) Always be sure to mount this unit in an area with proper ventilation to avoid overheating.

4) Please check if the output voltage of any LED power supplies used complies with the working voltage of the product.

5) Never connect any cables while power is on and always ensure correct connections to avoid short circuitsbefore switching on.

6)

7) For update information please consult your supplier.

Please ensure that the cable is secured tightly in the connector

1) We provide lifelong technical assistance with this product:

3-year warranty. We print date on every products, for example :1125 means year 2011,week 25.The warranty is for free repair or replacement and covers manufacturing faults only.

For faults beyond the 3-year warranty we reserve the right to charge for time and parts.

2) Limited Warrenty

Any defects caused by wrong operation.

Any damage caused by unauthorized removal, maintenance, modifying, incorrect connection and replacement of chips.

Any damage due to transportation, vibration etc. after purchase.

Any damage caused by earthquake, fire, lightning, pollution and abnormal voltage.

Any damage caused by negligence, inappropriate storing at high temperatures and humidity or near harmful chemicals.

Product has been updated

OperationL e a r n in g ( m a tc h in g )a. Do wiring according to connection diagramb. Wake up the remote control by touching ON/OFF button.c. Press learning button on receiver.d. Touch any zone button on remote control.e. Then touch color wheel.f. Connected LED light will blink to confirm zone designation.g. Press at learning button on receiver over 5 seconds until LED light flash, then delete the learned ID.

N o te 1 : T o c h o o s e a m a s te r f r o m s la v e s b y j u m pe r f o r e a c h z o n e .S h o r t c i r c u it f o r m a s te r.O pe n c i r c u it f o r s la v e .E a c h z o n e o n ly c a n s e t o n e m a s te r c o n tr o l le r. A fte r a p e r io d o f t im e , t h e m a s te r w i l l d o s y n c h r o n iz a tio n o pe r a tio n t o k e e p t h e s a m e c o lo r o r m o de o f a l l s la v e s i n o n e z o n e .

N o te 2 : E a c h r e m o te c o n tr o l 8 z o n e s ( a r e a s ) r e c e iv e r s , e a c h a r e a c a n b e l e a r n e d a s m a n y r e c e iv e r s a s we c a n .E a c h r e c e iv e r m a x im a l ly c a n b e c o n tr o l le d b y 8 d i ffe r e n t r e m o te c o n tr o l le r s .

Touch button is to switch on/off of each corresponding color.Hold your finger on button to dim brightness of each corresponding color. There are total 8 levels of brightness.Note: If you press R, then press G, then it is mix color of R and G. If you want to get G color directly, please press R to switch off of R first. Then press G.

R un n in g & P a u s e B u tto na. Press pause&run button mode will run. Press it once, it runs one mode. Press button again, it stops, then press one more time, it will enter next mode. There are total 10 build-in modes.b. Pause&run button can work with S button , it can save modes into different zone.c. Touch button one by one, such as press button 1,2,3,4,5,6, then

Press button. Zone 1,2,3,4,5,6 will run synchronized mode, after long press, LED lighting will flash twice, they will switch to chasing running mode, long press again to switch back.

R e tu r n b u tto nTouch button to return previous color or running mode.

S pe e d u p a n d S pe e d d o wn B u tto nTouch button to speed down when mode is running, touch button to speed up when mode is running.

B r ig h tn e s s d o wn o r u p b u tto nShort/long press button to dim down brightness of RGB channels, Short/ long press button to dim up RGB channels.

W” channel is separated from RGB channels, so we can only long press button to dimming“W” channel.

S a v e B u tto na. How to save color into different position per zone?

b. How to save m ode in to di f fe r e n t po sitio n per zone ?

c . R e c a l lChoose zone number form , then press button, and press the position button which color or mode saved into.

R G B

R G B

4 5 6

2 31

R G B W b u tto n

4 5 6

2 31

ZONETouch color wheel for select an ideal color

Select R/G/B/W color by press R G B

or

Long press button(the blue indicator will be on) for savingChoose position( ) to save colorany button

4 5 6

2 31

POSITION

Press any zone button you want

For example, press zone button 1, then touch color wheel for orange color, then press S button (the blue indicator will be on),then choose position button 3. That’s to say, we save orange color from zone 1 into position 3. So each zone can save 6 colors. 6 zones can save 36 colors.

4 5 6

2 31

ZONE

Press button for select an ideal mode

Press button(the blue indicator will be on) for savingChoose position( ) to save modeany button

4 5 6

2 31

POSITION

Press any zone button you want

4 5 6

2 31