Amrita Sai Institute of Science and TechnologyAPPROVED BY AICTE, NEW DELHI; AFFILIATED TO JNTU, KAKINADA

PARITALA, KRISHNA DISTRICT – 521 180 (A. P.)

Dt: 16-04-2014

Revision Schedule

Date LIST OF SUBJECTSIII EEE - A III EEE - B III ECE - A III ECE - B III CSE - A III CSE - B III IT III MECH

21, 22, 23/04/2014 UEE/PB MS/MS (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac)24, 25, 26/04/2014 MS/DBK UEE/PB (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac)28, 29, 30/04/2014

OR01, 02, 03/05/2014

EMD/KVKR MPMC/VS (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac)

04, 05, 06/05/2014 MPMC/VS EMD/KVKR (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac)08, 09, 10/05/2014 PSD/GKR PSA/JSR (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac)12, 13, 14/05/2014 PSA/JSR PSD/GKR (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac) (Sub/Fac)

Subject Wise Plan for Revision Schedule (III/II)Subject Faculty: Year / Sem: III / II Sem Chosen Units: U1, U2, U3, U4, U5

U1 S1 Content CoveredS2 Content Covered

U2 S3 Content CoveredS4 Content Covered

U3 S1 Content CoveredS2 Content Covered

U4 S3 Content CoveredS4 Content Covered

U5 S1 Content CoveredS2 Content Covered

Exam S3S4

Note: S1:- 9:00-10:40AM; S2:- 10:50-12:30PM; S3:- 1:10-3:00PM; S4:- 3:10-5:00 PM

II MID DESCRIPTIVE EXAMINATION SCHEDULE FOR III B TECH II SEMESTERDate LIST OF SUBJECTS

III EEE - A III EEE - B III ECE - A III ECE - B III CSE - A III CSE - B III IT III MECH23/04/2014 UEE MS26/04/2014 MS UEE

30/04/2014 or 03/05/2014 EMD MPMC06/05/2014 MPMC EMD10/05/2014 PSD PSA14/05/2014 PSA PSD

Subject Faculty: Mr. P.Bapaiah Year / Sem: III / II Sem Chosen Units: U1, U2, U3, U4, U5

UEE

U1S1

Energy star rating of the equipment, various terms used in DSM, Various forms of load management 

S2 Demand side management techniques, Demand response and importance

U2

S3 Resistance welding classification, Are welding classification

S4Spot welding machine, comparison of AC&DC welding; comparison of seam, spot & butt wildings 

U3

S1Sources of light, design of the filament lamp construction, sodium vapour lamp, principles of light control 

S2Mercury vapour lamp, fluorescent lamp, design of lighting, street, flood and intestinal lighting

U4S3 Modes of heat transfer, requirement of heating material, resistance heating classification

S4 Arc heating types, induction heating types, dielectric heating and its applications

U5

S1System of electric traction, review of existing systems, special features of traction motors 

S2Mechanics of trains movement speed time ensure for trapezoidal and quadrilateral with numericals.

Exam S3S4

Subject Faculty: Ms. M. Srivalli Sireesha Year / Sem: III / II Sem Chosen Units: U1, U2, U3, U4, U5

MS

U1S1 Nature, importance, functions, evolution of management, decision making process

S2 Theories of motivation, Types of organisational structures, principles

U2S3 Development of network, differences between PERT & CPM, Problems

S4 Problems on PERT, crashing

U3 S1 Importance of ethics in business & management, marketing

S2 Ethics in HRM & Tinance

U4S3 Communication process, report writing, cross cultural communication

S4 Presentation skills, interviews, vedio conferences

U5S1 Vision, mission, goals, strategy, corporate planning process

S2 Environmental scanning, swot analysis, generic strategy alternatives

Exam S3S4

Subject Faculty: Mr. K.V. Krishna Rao Year / Sem: III / II Sem Chosen Units: U1, U2, U3, U4, U5

EMD

U6S1

IM-I-Priciple of operation, o/p equation, design of stator widg, stator core, length of air gap

S2 Designing problems of stator core & windings

U7S3

IM-II-Design of squirrel cage rotor, design of rotor bars & slots, design of end ring, reduction of harmonic torque,

S4 design of.wound rotor & problems

U5S1 Construction of the X-mer, o/p eq of X-mer, emf per turn, design of core, overall

S2 Dimensions of X-mer,& problems.

U4S3 Estimation of No-load current o/p eq of 3- X-mer, alternate formula for

S4 Magnetizing current, design of winding with associated problems

U2S1 Single layer &double layer windings, emf equation, full pitch coil & concentrated

S2 Winding, design of simplex lap & wave wibding, multiplex lap & wave winding

Exam S3S4

Subject Faculty: Mr. B. Vijay Sekhar Year / Sem: III / II Sem Chosen Units: U1, U2, U3, U4, U5

MPMC

U1S1 Introduction to MP Architecture 

S2  

U2S3 Minimum mode and  Maximum mode operations

S4  

U3S1 Algorithms for assemble language programming 

S2  

U4S3 I/O Interface

S4  

U5S1 Introduction  to 8051 Micro Controller

S2 Introduction to MP Architecture 

Exam S3  S4

Subject Faculty: Mr. G.Koti Reddy Year / Sem: III / II Sem Chosen Units: U1, U2, U3, U4, U5

U1S1 Speed control techniques of DC motor, induction motor & Synchronous motor

S2

U2S3 Control of DC motor speed by single phase semi & full converter

S4 Problems

U3S1 DC motor speed control by three-phase demi and fully controlled converters,

S2 Wave forms & problems

U7S3 Speed control of induction motor from rotor side- performance characteristics

S4

U8 S1 Speed control of synchronous motor, closed loop control

S2

Exam S3S4

Subject Faculty: Mr. J. Samba Siva Rao Year / Sem: III / II Sem Chosen Units: U1, U2, U3, U4, U5

PSA

U1S1 Per Unit Quantities, advantages, Impedance diagram

S2 Problems

U2S3 Formation of  Z Bus

S4  

U3S1 Symmetrical Faults Analysis

S2  

U4S3 Symmetrical Components

S4  

U5S1 Unsymmetrical Faults

S2 Per Unit Quantities, advantages, Impedance diagram

Exam S3S4

Subject

Faculty:

Mr. P.Bapaiah

Year / Sem: III / II Sem

Chosen Units:

U1, U2, U3, U4, U5

 

 

 

UEE

U8S1

Energy star rating of the equipment, various terms used in DSM, Various forms of load management 

S2 Demand side management techniques, Demand response and importance

U3

S3 Resistance welding classification, Are welding classification

S4Spot welding machine, comparison of AC&DC welding; comparison of seam, spot & butt wildings 

U5S1

Sources of light, design of the filament lamp construction, sodium vapour lamp, principles of light control 

S2 Mercury vapour lamp, fluorescent lamp, design of lighting, street, flood and

intestinal lighting

U4S3

Modes of heat transfer, requirement of heating material, resistance heating classification

S4 Arc heating types, induction heating types, dielectric heating and its applications

U6

S1System of electric traction, review of existing systems, special features of traction motors 

S2 Mechanics of trains movement speed time ensure for trapezoidal and quadrilateral with numericals.

ExamS3  S4  

 

Subject Faculty: Ms. M. Srivalli Sireesha

Year / Sem: III / II Sem Chosen Units: U1, U2, U3, U4, U5

 

 

 

MS

U1S1

Nature, importance, functions, evolution of management, decision making process

S2 Theories of motivation, Types of organisational structures, principles

U4S3 Development of network, differences between PERT & CPM, Problems

S4 Problems on PERT, crashing

U6S1 Importance of ethics in business & management, marketing

S2 Ethics in HRM & Tinance

U7S3 Communication process, report writing, cross cultural communication

S4 Presentation skills, interviews, vedio conferences

U5 S1 Vision, mission, goals, strategy, corporate planning process

S2 Environmental scanning, swot analysis, generic strategy alternatives

ExamS3  S4  

 

 

 

 

 

Subject Faculty: Mr. K.V. Krishna Rao Year / Sem: III / II Sem Chosen Units: U1, U2, U3, U4, U5

 

 

 

EMD

U1S1  S2  

U2S3  S4  

U3S1  S2  

U4S3  S4  

U5S1  S2  

ExamS3  S4  

 

 

Subject Faculty: Mr. B. Vijay Sekhar Year / Sem: III / II Sem Chosen Units: U1, U2, U3, U4, U5

 

 

 

MPMC

U1S1 Introduction to MP Architecture 

S2  

U2S3 Minimum mode and  Maximum mode operations

S4  

U3S1 Algorithms for assemble language programming 

S2  

U4S3 I/O Interface

S4  

U5S1 Introduction  to 8051 Micro Controller

S2  

ExamS3  S4  

 

 

 

 

 

 

 

 

 

 

 

 

 

Subject Faculty: Mr. G. Koti Reddy Year / Sem: III / II Sem Chosen Units: U1, U2, U3, U4, U5

 

 

 

PSD

U1S1  S2  

U2S3  S4  

U3S1  S2  

U4S3  S4  

U5S1  S2  

ExamS3  S4  

Subject Faculty: Mr. J. Samba Siva Rao Year / Sem: III / II Sem Chosen Units: U1, U2, U3, U4, U5

 

 

 

PSA

U1S1 Per Unit Quantities, advantages, Impedance diagram

S2 Problems

U2S3 Formation of  Z Bus

S4  

U3S1 Symmetrical Faults Analysis

S2  

U4S3 Symmetrical Components

S4  

U5S1 Unsymmetrical Faults

S2  

ExamS3  S4