Upload
newesterth
View
215
Download
0
Embed Size (px)
Citation preview
8/11/2019 RMVL600 Remote
1/52
2-674-860-12 (1)
Integrated RemoteCommander
Operating Instructions
2006 Sony Corporation
RM-VL600
8/11/2019 RMVL600 Remote
2/52
2
For the customers in the U.S.A.WARNINGThis equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipmentgenerates, uses, and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may causeharmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more ofthe following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expresslyapproved in this manual could void your authority to operate thisequipment.
8/11/2019 RMVL600 Remote
3/52
3
Features
The RM-VL600 Remote Commander provides centralized control of all
your AV components from a single remote commander and saves thetrouble of operating different AV components with different remotecontrol devices. The following are its main features.
Centralized control of Sony AV components with this one remotecommander
This Commander is preset at the factory to operate Sony brandcomponents, so you can use it out of the box as a control center for your
Sony AV components.
Remote control signals for non-Sony components are also preset
This Commander is preset for most major brands components as well asSony. You can remote control your non-Sony components by setting thetype and code number of each component (page 10).
Learning function for programming various other remote control
signalsThis Commander has a Learning function, to learn the remote controlsignals needed to operate other non-preset components or functions. (Toteach such signals to this Commander, use the remote control suppliedwith the non-preset components.) (page 16)In addition, the Commander can learn remote control signals (infraredsignals only) of non-Audio Visual components such as air-conditioners,lights, etc. (Some specific appliances or functions may not be available.)
(page 24)
Reassigning new components
You can assign Component Select buttons to freely operate othercomponents. This is useful when you have more than two of the samekind of AV component (only if a Component Select button is free.) (page33)You can only assign TVs to the TV Component Select button.You can only assign an amplifier or DVD/Receiver combo to the AMPComponent Select button.
8/11/2019 RMVL600 Remote
4/52
Startup Guide
This guide shows you how to set the Remote Commander to operate
your components.First, find the four-digit component code number for yourcomponent, referring to the supplied Component code numbers.
Example: To set up a TV ofthe code number 8011
1 Set the RemoteCommander for code inputmode.
2 Press the desiredComponent Select button.
3 Enter the code number.
4 Finish setting.
SET
MENU
+
Press SET and MENU.
SET
SATDVDTV CBL
TAPECDVCR AMP
ENT
Press ENT.
You can search for thecomponent code available foryour component.
1 Set the RemoteCommander for codeinput mode.
2 Press the desired
Component Select button.
3 Transmit code numbersignals in turn.
4 Finish setting.
SET
MENU
+
Press SET and MENU.
SET
SATDVD
TV CBL
TAPECDVCR AMP
CH
POWER
ENTPress ENT.
8 0 1 1
For more details, see page 13.
Press CH + or CH , and thenPOWER. Repeat until yourcomponent reacts.
If you have the codenumber
If you cannot find thecode number
For more details, see page 10.
4
8/11/2019 RMVL600 Remote
5/52
1 Place the RM-VL600 head to
head with your VCRsremote control.
2 Set the RM-VL600 forlearning mode.Press and hold SET for at least
3 seconds until the SETindicator flashes.
3 Press the desiredComponent Select button.
If your component does not work as supposed even if the code
number is set, make the RM-VL600 learn the functions ofyour components remote control.
Learning function
Example:To teach theN(play) signal of your video cassetterecorder to the VCRNbutton of the RM-VL600
VCRs remotecontrol
RM-VL600
SET
VCR
4 Press the button you
want to teach.
5 Press and hold theN(play) button of yourVCRs remote control untilthe VCR button of theRM-VL600 lights up.
6 Repeat Steps 4and 5toteach other functions.
7 Finish setting.
For more details, see page 16.
2 4 inches(5 10 cm)away (approx.)
SET
Press SET.
5
8/11/2019 RMVL600 Remote
6/52
6
Table of Contents
Getting Started
Installing the Batteries .................................................................................8When to replace the batteries ............................................................................ 8
Location of Controls .....................................................................................9
Basic Operations
Setting the Code for non-Sony Preset Audio and Visual Components
Setting component codes ...................................................................10Setting a component code ................................................................................ 10
Checking if the code number works .............................................................. 12
Setting a Component Code by the Search Function ...................................13
Operating Your Components with the Remote Commander ......................14
To control the volume ....................................................................................... 15
Programming Signals of Another Remote Control Learning Function...16
For accurate Learning ....................................................................................... 19
Programming remote control signals to theComponent Select buttons and System Control buttons .......................... 20
Changing or erasing the function of a learned button ............................ 22
Notes on programming the signals for an air-conditioner ......................... 24
Advanced Features
Controlling the Volume of Visual Components Connected to an Audio
System ......................................................................................................25
Adding an Extra Function to the Component Select Buttons .....................27
Programming the Power-On Command of the Selected Component justby pressing that Component Select button(for Sony Components only) ........................................................................ 27
Executing a Series of Commands System Control Functions .................29To clear programmed commands ................................................................... 31
Programming a Series of Commands to on the Component Select
Buttons .....................................................................................................32
To clear programmed commands ................................................................... 33
Assigning Other Components to the Component Select Buttons .............. 33
Using Other FunctionsLocking the Controls Hold Function .......................................................34
Erasing all settings To reset the Commander to its factory settings .....35
8/11/2019 RMVL600 Remote
7/52
7
Additional Information
Precautions .................................................................................................36
Maintenance ...............................................................................................36
Specifications..............................................................................................36
Troubleshooting ..........................................................................................37
Appendixes
Table of Preset Functions ............................................................................39
TV (ANALOG) .................................................................................................. 39
TV (DIGITAL) .................................................................................................... 40
VCR ..................................................................................................................... 41
CBL (Cable box) ................................................................................................. 41
SAT ...................................................................................................................... 42
DVD .................................................................................................................... 42
DVR (Digital video recorder) .......................................................................... 43CD ....................................................................................................................... 44
MD....................................................................................................................... 44
DAT ..................................................................................................................... 45
DECK .................................................................................................................. 45
AMP .................................................................................................................... 45
Digital Cable Box .............................................................................................. 46
DAV (DVD/Receiver combo) ......................................................................... 46Digital TV TUNER ............................................................................................ 47
Index ...........................................................................................................48
8/11/2019 RMVL600 Remote
8/52
8
Getting Started
Installing theBatteries
Slide open the batterycompartment lid and insert twosize AA (R6) batteries (notsupplied). Be sure to match up the+ and indications on thebatteries with the + and indications on the battery
compartment.
When to replace thebatteries
Batteries for remote controloperation (two size AA (R6)batteries)Under normal conditions, thebatteries will last up to sixmonths. If the Commander doesnot operate properly, the batteriesmight be drained. When this
happens, replace the batteries withnew ones.
NoteDo not take more than one hour toreplace the batteries. Otherwise, yourcode number settings (page 10) andlearned remote control signals (page16) will be erased.
Notes on batteries Do not use an old battery with a new
one, or mix different types ofbatteries together.
If the electrolyte inside the batteryshould leak, wipe the contaminatedarea of the battery compartment witha cloth and replace the old batterieswith new ones. To prevent electrolytefrom leaking, remove the batteries ifyou plan not to use the Commanderfor a long period of time.
Insert the batteries (negative endfirst) through the guide clampwithin each compartment asshown above.
8/11/2019 RMVL600 Remote
9/52
9
Location of Controls1 SET indicator
2 SET button3 Component Select buttonsLight or flash during operation.
4Number buttons
5DIGITAL/ANALOG button
6VOL +/ buttons*
7 INFO button
8MUTING button*9GUIDE button
0 EXIT button
qa Player Control buttons
qs TV/VIDEO button
qd POWER button
qf ENT (enter) button
qg TWIN VIEW buttonqh CH (channel) +/ buttons
qj SLEEP button
qk RECALL button
qlMENU button
w; Cursor Control buttons
wa TOOLS button
ws SYSTEM CONTROL buttonswdDOT button
SET POWER
SATDVDTV CBL
TAPECDVCR
1
VIDEO1
2
VIDEO2
3
AUX
4
TUNER
5
CD
6
TAPE
7
MD
8
TV
9
PHONO
VOL CH
0
DVD
DIGITAL
/ANALOG
TWIN VIEW
SLEEP
INFO
GUIDE MENU
EXIT TOOLS
SYSTEM CONTROL
RECALLMUTING
AMP
ENT
OK
A B C D
TV/VIDEO
qs
qd
qf
qg
qh
qj
qk
ql
w;
ws
wa
1
5
6
7
8
9
0qa
2
wd
3
4
About tactile dotsThe number 5 button, the Bbutton and CH + button each have a tactile dot for easeof use.
* Note on the VOL +/ and MUTING buttonsThe Commander controls or mutes the TVs volume when you select a visualcomponent. The Commander controls or mutes the amplifiers volume when youselect an audio component. You can change this setting (page 25).
NoteThe function of the control buttons varies depending on settings/operating modes.The Table of Preset Functions (page 39) shows how the Commander generally
operates for each component in the factory preset mode.
8/11/2019 RMVL600 Remote
10/52
10
SET POWER
SATDVDTV CBL
TAPECDVCR
1
VIDEO1
2
VIDEO2
3
AUX
4
TUNER
5
CD
6
TAPE
7
MD
8
TV
9
PHONO
VOL CH
0
DVD
DIGITAL
/ANALOG
TWIN VIEW
SLEEP
INFO
GUIDE MENU
EXIT TOOLS
SYSTEM CONTROL
RECALLMUTING
AMP
ENT
OK
A B C D
TV/VIDEO
2
4
5
2
3
2 Press and while holdingSET, press MENU.
The SET indicator lights up.
Example: To set up a Philips TV
1 See the tables in thesupplied ComponentCode Numbers, and findthe four-digit component
code number for thedesired component.
If more than one code numberis listed, use the number that islisted first.For example, to set up aPhilips TV, you would use the
code number 8011.
Setting a component code
SET
SET
MENU
+
NoteAn MD player and a DAV can be set toany of the above Component Select
buttons. You can assign ComponentSelect buttons to freely set signals ofyour desired components. For furtherinformation, see Assigning Other
Components to the Component SelectButtons (page 33) .For the functions of buttons as for eachcomponent, see Table of PresetFunctions (page 39).
Basic Operations
Setting the Code fornon-Sony Preset
Audio and VisualComponents Settingcomponent codes
The Commander is preset at the
factory to operate Sony brand AVcomponents (see the table below).If you are using the Commanderwith a factory-set Sonycomponents, skip the followingprocedures.You can use the Commander withother major brand preset AV
components also. To use withother AV components, or Sonycomponents which do notfunction with the Commander,you need to follow the proceduresto set the correct codes for eachcomponent.
ComponentSelect Button
TV
DVD
SAT
CBL
VCR
CD
TAPE
AMP
Factory setting
Sony TV
Sony DVDplayer
Sony satellitetuner
Analog cablebox
Sony VHSVCR
Sony CDplayer
Sony cassettedeck
Sony amplifier
Presetcomponent(s)
TVTV/VCRCombo
DVD player
Satellitetuner
Cable box
VCR
CD player
Cassettedeck
Amplifier
8/11/2019 RMVL600 Remote
11/52
11
3 Press the Component Selectbutton for the desiredcomponent.
The SET indicator and theselected Component Selectbutton lights up.
4 Press the Number buttons
to enter the four-digitcomponent code number.
5 Press ENT.The SET indicator and theComponent Select button lightturns off.
If the Component Select buttonflashes five times beforeturning off, it means that thesetup is incomplete. Start overfrom Step 2.
Continued
Notes If you press a component code
number that is not on the table in thesupplied Component CodeNumbers, or if you press a button inthe wrong order, the Component
Select button flashes five times, andthen turns off. Check the componentcode number, and try setting it again.
If you dont input anything into theCommander within 20 seconds
between each step, the setupprocedure will be canceled. To set thecode, start over from Step 2.
If you press SET while setting the
component code, all code numbers willbe lost, and the setup procedure willbe canceled. Start over from Step 2.
To cancel setup, press SET.
TV
SET
SATDVD
TV CBL
TAPECDVCR AMP
TV TV
8/11/2019 RMVL600 Remote
12/52
12
Setting the Code for non-SonyPreset Audio and VisualComponents Settingcomponent codes (continued)
Checking if the codenumber works
1 Power on the componentwith its power switch.
2 Press the correspondingComponent Select buttonfor the component youhave set up.
The Component Select buttonlights up when you press it,and turns off when you release
it.
3 Aim the Commander at thecomponent and press
POWER.The selected Component Selectbutton lights up when youpress a function button, andturns off when you release it.
The component should poweroff.
4 If you have succeeded,
check that the Commanderis operating the otherfunctions of yourcomponent, such as channeland volume control.
See page 14 for details.
If the Commander does notseem to be workingTry repeating the setup procedureusing the other codes listed for yourcomponent, or try setting the codenumber using the Search function
(page 13).
Note on the VOL+/ and MUTINGbuttonsWhen you operate a visualcomponent, the TV button lightsup to indicate that the
Commander is controlling ormuting the TVs volume.
When you operate an audiocomponent, the AMP button lightsup to indicate that the
Commander is controlling ormuting the amplifiers volume.
It is recommended that you firstset the TV and AMP codes beforesetting up any other components.
Note on buttons that havealready learned remotecontrol signalsIf another signal has already beenprogrammed on a button usingthe Learning function (page 16),that learned signal will continue
to work even after you set thecomponent code number. To use itas a preset function button, youmust first erase its learnedsignal (page 22).
TV TV
SATDVD
TV CBL
TAPECDVCR AMP
POWER
TV
AMP
8/11/2019 RMVL600 Remote
13/52
8/11/2019 RMVL600 Remote
14/52
14
Example: To operate a videocassette recorder
1 Press the desiredComponent Select button.
The Component Select buttonlights up when you press it,and turns off when you releaseit.
4 Press ENT.
The SET indicator and theComponent button turns off.
If the Component Select buttonflashes five times before turningoff, it means that the setup isincomplete. Start over from Step 1.
5 Check if the code number
works by following theinstructions on page 12.
Notes If you dont input anything into the
Commander within 20 secondsbetween each step, the setupprocedure will be canceled. To set the
code, start over from the beginning. If you press any button other thanCH +/ and POWER while settingthe component code, all codenumbers will be lost, and the setupprocedure will be canceled. Start overfrom the beginning.
To cancel setup, press SET.
SET POWER
SATDVDTV CBL
TAPECDVCR
1
VIDEO1
2
VIDEO2
3
AUX
4
TUNER
5
CD
6
TAPE
7
MD
8
TV
9
PHONO
VOL CH
0
DVD
DIGITAL
/ANALOG
TWIN VIEW
SLEEP
INFO
GUIDE MENU
EXIT TOOLS
SYSTEM CONTROL
RECALLMUTING
AMP
ENT
OK
A B C D
TV/VIDEO
1
2
TV TV
Setting a Component Code bythe Search Function (continued)
VCR VCR
Operating YourComponents with the
Remote CommanderWhen you operate a non-Sonycomponent, make sure you set thecomponent code first (page 10).
ENT
8/11/2019 RMVL600 Remote
15/52
15
To control the volumePress VOL +/ to control thevolume. Press MUTING to mutethe sound.When you select a visualcomponent, the TVs volume willbe controlled (TV ComponentSelect button lights up), and whenyou select an audio component,the amplifiers volume will becontrolled (AMP Component
Select button lights up). You canchange this setting (page 25).
Notes If you used the Learning function
(page 16) to program the VOL +/ orMUTING button to send a signal toany other component, that signal will
be transmitted instead of the volume
or muting of the TV or amplifierwhen you select that component. If you used the Learning function
(page 16) to program the VOL +/ orMUTING button for the TV or AMP
buttons to send a signal to any othercomponent, that signal will betransmitted only when you select TVor AMP. When you select anothercomponent, the preset volume controlsignals for TV or AMP will betransmitted.
If you have assigned anothercomponent to the TV or AMP buttons(page 33), the volume of the TV oramplifier cannot be controlled even ifyou select another component.
2 Press any Player Controlbutton.
See Table of Preset Functions(page 39) for the functions ofbuttons for each component.
NoteThe remote control signals may bedifferent for some components orfunctions. In this case, program theremote control signals with theLearning function (page 16). Note,however, that components andfunctions that do not support theremote control of infrared signals willnot work with this Commander.
8/11/2019 RMVL600 Remote
16/52
16
Example: To program theN(Play) signal of your videocassette recorder to the VCRN(Play) button of the Commander
1 Place the RM-VL600 headto head with your
components remotecontrol.
SET POWER
SATDVDTV CBL
TAPECDVCR
1
VIDEO1
2
VIDEO2
3
AUX
4
TUNER
5
CD
6
TAPE
7
MD
8
TV
9
PHONO
VOL CH
0
DVD
DIGITAL
/ANALOG
TWIN VIEW
SLEEP
INFO
GUIDE MENU
EXIT TOOLS
SYSTEM CONTROL
RECALLMUTING
AMP
ENT
OK
A B C D
TV/VIDEO
2,7
3
4
4
about 2 4 inches(5 10 cm) away
Remote control foryour component
RM-VL600
Programming Signalsof Another Remote
Control LearningFunction
To operate components orfunctions which do not work evenif you set a component codenumber, use the following
Learning procedure to teach anyof the programmable buttons ofthe Commander to operate thefunctions of another remotecontrol. You can also use theLearning function to change thesignals of individual buttons aftersetting the component code
number (page 10). It isrecommended that you make anote of the learned keyfunctions. (It is possible to make anote on the back of the suppliedComponent code numbers.)
Notes
Some specific remote control signalsmay not be learned.
You can also use a display monitorfor computer display (including a
built-in tuner type), if theCommander is learned.
8/11/2019 RMVL600 Remote
17/52
17
4 Press the button on theCommander you want toteach.
The SET indicator flashes andthe selected Component Selectbutton lights up. (Learningfunction standby).
If another signal has alreadybeen learned by thatbutton
The SET indicator flashestwice, and the Commandertakes no action returning to itsstate after the ComponentSelect button was pressed inStep 3. Either teach to
another free button, or clear thealready learned function(page 22) and start over fromthe beginning.
SET
SATDVDTV CBL
TAPECDVCR AMP
2 Press and hold SET for over3 seconds.
The SET indicator flash.
SET
SATDVDTV CBL
TAPECDVCR AMP
3 Press the Component Selectbutton for the componentwhose signals are to belearned.
The SET indicator flashes andthe selected Component Selectbutton light up.
VCR
SET
SATDVDTV CBL
TAPECDVCR
AMP
SET
Continued
8/11/2019 RMVL600 Remote
18/52
18
Programming Signals of AnotherRemote Control LearningFunction (continued)
5 Press and hold the buttonon the other remote control,until both the SET indicatorand the Component Selectbutton lights up again.
During data transfer, only theSET indicator stays lit, and the
Component Select button turnsoff.After data transfer is complete,the Commander returns to itsstate in Step 3.
If the SET indicator flashesfive timesIt means that learning isincomplete. Repeat steps 4 and 5.
6 Repeat Steps 4 and 5 toteach functions to other
buttons.To teach anothercomponents remote control
signalAfter positioning the two remotecommanders as in Step 1 on page16, press the correspondingComponent Select button, and thenfollow Steps 4 and 5 to perform
Learning.
7 Press SET to finish setting.
SET SET
VCR VCR
during datatransfer
data transfercomplete
Notes If you do not perform Learning steps
within 20 seconds at any point duringthe process, Learning mode ends.
If you do not perform Step 5 within10 seconds after Step 4, the learning
procedure returns to Step 3. RepeatStep 4 while the Component Select
button lights.
To cancel setup, press SET.
If the Commander does notseem to be workingIf the learned button does not
operate properly, teach once again.(For example, if the volume becomesvery loud after pressing VOL + onlyonce, noise may have interfered duringthe Learning procedure.)
If you set a component codeafter learning a signalIf you have programmed any signal on
a button by the Learning function, thatsignal will work even after you set acomponent code.
Note on the REC zsignalYou can only teach to one button at atime. Therefore you cannot teach asequential button operation (forexample RECz+ B) to a single buttonon the Commander. In this case,
teach the functions of each button onyour component to the Commander.
remote control
of component
8/11/2019 RMVL600 Remote
19/52
19
Continued
When you teach signals toVOL +/ or MUTINGIf you used the Learning
function to program the VOL +/or MUTING buttons to send anysignal to components other thanthe TV or AMP, that signal willbe transmitted only by pressingVOL +/ or MUTING when youselect that component.
If you used the Learningfunction to program the VOL +/
or MUTING buttons to send anysignal to the TV or AMP, thatsignal will be transmitted onlyafter you select TV or AMP.When you select othercomponents, the learnedsignal will be transmitted.
To teach the signals for anair-conditionerSee Notes on programming thesignals for an air-conditioner onpage 24.
For accurate LearningDo not move the remote units
during the Learning procedure.Be sure to keep holding down
the learning button until yourCommander reacts as described.
Use fresh batteries in bothremote units.
Avoid Learning in places subjectto direct sunlight or a strongfluorescent light. (Noise may
interfere during the Learningprocedure.)
The remote control detector areamay differ depending on eachremote unit. If Learning does notwork, try changing the positionsof the two remote control units.
When you teach signals of aninteractive signal exchangesystem remote control unit(supplied with some of Sonysamplifiers) to the Commander,the response signal of the mainunit may interfere with thelearning of the Commander. In
such a case, move to a placewhere the signals will not reachthe main unit (e.g. other rooms,etc.).
IMPORTANTBe sure to place the
Commander out of the reach ofsmall children or pets, and lockthe controls using the Holdfunction (page 34).Components such as airconditioners, heaters, electricappliances, and electric
shutters or curtains receivingan infrared signal can bedangerous if misused.
8/11/2019 RMVL600 Remote
20/52
20
2 Press and hold theComponent Select buttonfor the component whosesignals are to be learnedfor over 3 seconds.
To teach signals to the SYSTEMCONTROL buttons, press and
hold the desired SYSTEMCONTROL button for over 3seconds.
Both the SET indicator and theselected Component Selectbutton light up.
When you teach signals tothe SYSTEM CONTROL
buttons, only the SET indicatorlights up.
When the SET indicator lightsup, you can release theComponent Select button. TheSET indicator flashes and theselected Component Select
button lights up (Learningfunction standby).
When you teach signals tothe SYSTEM CONTROLbuttons, you can release theSYSTEM CONTROL buttonwhen the SET indicator lightsup. The SET indicator lightsup, but the SYSTEM
CONTROL button does notlight up.
DVD
SET
SAT
DVDTV CBL
TAPECDVCR AMP
SET
SATDVDTV CBL
TAPECDVCR AMP
Programming signals of anotherremote control LearningFunction (continued)
Programming remotecontrol signals to theComponent Select buttonsand System Controlbuttons
You can teach one operatingprocedure to a Component Selectbutton and System Controlbuttons, so that when you pressthe Component Select button andSystem Control buttons, theoperation is also automaticallydone.
For example, if it is necessary toswitch the input selection of anamplifier to DVD when you use aDVD player, teach an inputselect signal to the DVD button.After learning, the inputselection of an amplifier is
automatically switched to DVDjust by pressing DVD. (For thisoperation, the amplifier shouldfirst be turned on.)
Example: To teach the DVDinput remote control signal ofyour amplifier to the DVDComponent Select button of theCommander
1 Follow Steps 1 to 2 (page16).
8/11/2019 RMVL600 Remote
21/52
21
Continued
3 Press and hold the buttonon the other remote control,
until the SET indicatorlights and all theComponent Select buttonsflash again.
During data transfer, only theSET indicator stays lit, and the
Component Select button turnsoff.
If the SET indicator flashesfive timesIt means that learning isincomplete. Repeat Steps 2 and 3.
4 Repeat Steps 2 and 3 toteach remote controlsignals to other buttons.
5 Press SET to finishlearning.
Notes If you do not perform Learning steps
within 20 seconds at any point duringthe process, Learning mode ends.
If you do not perform Step 3 within10 seconds after Step 2, the Learningprocedure returns to Step 1. Repeat
from Step 2 while the ComponentSelect button is lit.
To cancel learning, press SET.
If another signal has alreadybeen learned by thatbuttonThe SET indicator flashes twice,and the Commander takes noaction, returning to its state after
SET was pressed and held in Step 2.Either teach to another free
button, or clear the alreadylearned function (page 22) andstart over from the beginning.
8/11/2019 RMVL600 Remote
22/52
22
Example: To erase the learnedfunction from the Numberbutton 1 in VCR mode
1 Press and hold SET for over3 seconds.
The SET indicator flashes.
2 While holding the desired
Component Select buttonpressed, press the buttonyou want to erase.
When erasing of the learnedfunction is completed, theselected Component Selectbutton light turns off.
NoteBe sure to press the button youwant to erase while pressing theComponent Select Button. If yourelease the Component Select
button, the Commander changes toLearning mode.
3 Press SET to finish setting.
To cancel erasing, press SET.
SET POWER
SATDVDTV CBL
TAPECDVCR
1
VIDEO1
2
VIDEO2
3
AUX
4
TUNER
5
CD
6
TAPE
7
MD
8
TV
9
PHONO
VOL CH
0
DVD
DIGITAL
/ANALOG
TWIN VIEW
SLEEP
INFO
GUIDE MENU
EXIT TOOLS
SYSTEM CONTROL
RECALLMUTING
AMP
ENT
OK
A B C D
TV/VIDEO
1,3
2
SET
SATDVDTV CBL
TAPECDVCR
AMP
SETSET
VCR VCR
Programming signals of anotherremote control LearningFunction (continued)
Changing or erasing thefunction of a learnedbutton
To change the learned function,clear it first and perform Learningagain.
To clear the learned functionof a single button
1+VCR
SET
during dataerasing data erasingcomplete
8/11/2019 RMVL600 Remote
23/52
23
SET
SATDVDTV CBL
TAPECDVCR AMP
SET
SATDVDTV CBL
TAPECDVCR AMP
x
SET
SATDVDTV CBL
TAPECDVCR AMP
To clear all function signalslearned for a specificComponent Select button
Example: To erase all functionslearned by the VCR button
1 Press and hold SET for over3 seconds.
The SET indicator flashes.
SET
To erase the learned function ofthe Component Select buttonand System Control buttons
Example: To erase the functionlearned by the TV button
1 While holding SET pressed,press and hold the TVComponent Select buttonfor over 3 seconds.
When erasing of a learnedfunction is completed, the SET
indicator light turns off.
To erase the learnedfunction of a SYSTEMCONTROL buttonWhile holding SET pressed, pressand hold the desired SYSTEMCONTROL button for over 3
seconds.
SET POWER
SATDVDTV CBL
TAPECDVCR
1
VIDEO1
2
VIDEO2
3
AUX
4
TUNER
5
CD
6
TAPE
7
MD
8
TV
9
PHONO
VOL CH
0
DVD
DIGITAL
/ANALOG
TWIN VIEW
SLEEP
INFO
GUIDE MENU
EXIT TOOLS
SYSTEM CONTROL
RECALLMUTING
AMP
ENT
OK
A B C D
TV/VIDEO1,3
2
Continued
8/11/2019 RMVL600 Remote
24/52
24
Programming signals of anotherremote control LearningFunction (continued)
2 While holdingxpressed,press the Component Selectbutton you want to erase.
When erasing of a learnedfunction has completed, all theother Component Select buttonlights turn off.
Notes With this operation, you can only
erase the learned functions ofall buttons for a specificcomponent.
To erase a single learned
function of a Component Selectbutton, see page 22.
3 Press SET to finish setting.
To cancel erasing, press SET.
SETSET
VCR VCR
VCR
during dataerasing
data erasingcomplete
Notes on programming thesignals for an air-conditioner
About seasonal adjustmentsIf you change the settings of theair-conditioner for the season, youhave to program the remotecontrol signals of the new settingson the Commander.
If the power-on/off operation
does not work correctlyIf the Commander can onlyoperate ON with one buttonand OFF with another, whileyour air-conditioners remotecontrol can operate ON/OFFwith a single button, program the
signal on two buttons of theCommander as follows.
1 Clear the learned power-on/off signal on the programmedbutton of the Commander.
2 Reprogram only the power-onsignal of the air-conditioner on
the button of the Commanderby following the steps ofProgramming signals ofanother remote control-Learning Function (page 16).
3 Program the power-off signal ofthe air-conditioner on anotherbutton of the Commander.
The two buttons of theCommander have beenprogrammed with the power-onsignal and the power-off signal ofthe air-conditioner respectively, sothat you can operate the air-conditioner with the Commander.
8/11/2019 RMVL600 Remote
25/52
25
1 Press and while holdingSET, press MENU.
The SET indicator lights up.
Component Select
buttonTV
VCR
CBL
DVD
SAT
AMP
CD
TAPE
Controls the volume of
TV
TV
TV
TV
TV
amplifier
amplifier
amplifier
Advanced Features
Controlling the Volumeof Visual Components
Connected to an AudioSystem
The Commander is factory presetbased on the assumption that youhear the sound of your visualcomponents from your TV
speakers, and that you hear soundof your audio components fromthe loudspeakers connected toyour amplifier.
For example, to control thevolume while using a VCR, youdont need to press the TV button
to control the TV volume.
The following table shows thefactory setting of which volumewould be controlled for eachcomponent.
SET POWER
SATDVDTV CBL
TAPECDVCR
1
VIDEO1
2
VIDEO2
3
AUX
4
TUNER
5
CD
6
TAPE
7
MD
8
TV
9
PHONO
VOL CH
0
DVD
DIGITAL/ANALOG
TWIN VIEW
SLEEP
INFO
GUIDE MENU
EXIT TOOLS
SYSTEM CONTROL
RECALLMUTING
AMP
ENT
OK
A B C D
TV/VIDEO
1
2
1
However, if your visualcomponents are connected to anaudio system, you may want tohear TV or VCR sound from theloudspeakers via your amplifier or
DAV, not from your TV speakers.In this case, you need to changethe factory preset so that you cancontrol the volume of your visualcomponents without first havingto switch to the amplifier or DAV.
SET
MENU
+
To change the Factory Preset ofthe Volume Control
Continued
SET
8/11/2019 RMVL600 Remote
26/52
26
SATDVDTV CBL
TAPECDVCR AMP
SATDVDTV CBL
TAPECDVCR AMP
To set only the audiocomponents volume controlsto AMPPress VOL while holdingMUTING pressed.
Only AMP lights up when youpress these buttons, and thenturns off when you release them.
Press and while holding VOL,press MUTING.
Volume control setting complete.
Visual components are:TV, video cassette recorder,analog cable box, digital cablebox, digital satellite tuner,DVD player, digital videorecorder
Audio components are:CD player, MD player,cassette deck, amplifier, DAV
To cancel setting, press SET.
Notes If you used the Learning function to
program the VOL +/ or MUTINGbuttons to send a signal to acomponent, the procedure above willnot change the function of the VOL+/ and MUTING buttons.
SATDVDTV CBL
TAPECDVCR AMP
SATDVDTV CBL
TAPECDVCR AMP
Controlling the Volume of VisualComponents Connected to an
Audio System(continued)
2 While holding MUTINGpressed, press VOL + orVOL .
To set all volume controls toAMPPress VOL + while holdingMUTING pressed.All Component Select buttonslight up when you press thesebuttons, and then turn offwhen you release them.
Press and while holding VOL+,press MUTING.
Volume control setting complete.
8/11/2019 RMVL600 Remote
27/52
27
Example: To clear the Power-oncommand
1 Press and while holding
SET, press MENU.
The SET indicator lights up.
Adding an ExtraFunction to the
Component SelectButtons
Programming the Power-Oncommand of the selectedcomponent just by pressing
that Component Selectbutton (for Sonycomponents only)
When a code number of a Sonycomponent is set to a ComponentSelect button, the Power-On signal
is automatically programmed tothe button. You can select thedesired component and power iton by just pressing thatComponent Select button.
SET
MENU
+
2 While holding POWERpressed, press the desiredComponent Select button.
While the POWER button is
pressed, the Component Selectbuttons that Sony componentsare set to flash in the followingorder.TVtDVDtSATtCBLtVCRtCDtTAPEtAMPThe Component Select buttonsthat Sony components are not
set to do not flash.
Continued
SET
SET POWER
SATDVDTV CBL
TAPECDVCR
1
VIDEO1
2
VIDEO2
3
AUX
4
TUNER
5
CD
6
TAPE
7
MD
8
TV
9
PHONO
VOL CH
0
DVD
DIGITAL
/ANALOG
TWIN VIEW
SLEEP
INFO
GUIDE MENU
EXIT TOOLS
SYSTEM CONTROL
RECALLMUTING
AMP
ENT
OK
A B C D
TV/VIDEO
1
2
1
8/11/2019 RMVL600 Remote
28/52
8/11/2019 RMVL600 Remote
29/52
29
SET POWER
SATDVDTV CBL
TAPECDVCR
1
VIDEO1
2
VIDEO2
3
AUX
4
TUNER
5
CD
6
TAPE
7
MD
8
TV
9
PHONO
VOL CH
0
DVD
DIGITAL
/ANALOG
TWIN VIEW
SLEEP
INFO
GUIDE MENU
EXIT TOOLS
SYSTEM CONTROL
RECALLMUTING
AMP
ENT
OK
A B C D
TV/VIDEO
1,3
1
2
Executing a Series ofCommands System
Control FunctionsWith the System Control function,you can program a series ofoperating commands, and executethem by pressing just one button.You can program up to 16consecutive operation steps to
each of the SYSTEM CONTROLbuttons (A D).If you have set the System Controlfunction for a Component Selectbutton (page 33), the execution ofthe programmed commandsbegins when you press the
Component Select button for morethan 2 seconds.When executing the programmedcommands, each remotecommander signal is transmitted.
Example: To watch a video, youcan set a series of operations asfollows:
Power on the TV.rPower on the video (VCR).
rPower on the amplifier.
rSet the input selector of theamplifier to VIDEO 1.
rSet the input mode of the TVto VIDEO 1.
rStart video playback.
Continued
8/11/2019 RMVL600 Remote
30/52
30
Example: To program theprocedure above to the SYSTEMCONTROL B button
1 Press and while holdingSET, press the SYSTEMCONTROL B button.
The SET indicator light turnson.
If a System Control function(System Control Macro) hasalready been set on the button,the SET indicator flashes twice.The setting procedure isautomatically canceled.
2 Set the System Controlfunction.With this example, pressbuttons in sequence as below:
You can program up to 16consecutive steps on each ofthe SYSTEM CONTROLbuttons (A D), including theinitial step of pressing switchto a Component Select button.
3 Press SET to complete theprogramming.The SYSTEM CONTROLbutton light turns off.
To program a new series ofoperations for those buttonswhich already have a controlprogram set
Erase the program (page 31).
Notes If you interrupt the procedure at any
point for over 20 seconds, the settingmode ends and the series ofcommands will be programmed up tothat point. In this case, clear theprogram (page 31) and start again
from Step 1 to set the entire programfrom the beginning. You cannotcontinue programming once thesetting mode ends.
If a SYSTEM CONTROL button hasalready learned a remote controlsignal (page 16), you can program aSystem Control function (SystemControl Macro), but the function does
will not work until you clear theLeaning function. To clear theLearning function, see Changing orerasing the function of a learned
button on page 22. If you change the component code
number (page 10) or program a newsignal by using the Learning function(page 16) on a key or a button that
has been programmed with a seriesof commands using the SystemControl function, the new signal will
be transmitted when you press thecorresponding SYSTEM CONTROL
button. While in setting mode, you cannot
clear any operation step you haveprogrammed. If you haveprogrammed an incorrect operation
by mistake, start again from Step 1. If you try to program more than 16
steps, the System Control settingmode ends, and the 16 steps you haveprogrammed are registered. If youwant to program the steps again,clear the program (page 31) and startagain from Step 1.
SET
POWERTV
1
VCR
POWERPOWER
VCR
AMP
VIDEO1
TV
TV/VIDEO
8/11/2019 RMVL600 Remote
31/52
31
Executing a Series of Commands System Control Functions(continued)
Tips for programming the
System Control functions
The following information helpsyou to program a consecutiveoperation steps.
About the order of operationsteps
Some of the components may notaccept consecutive remote controlsignals. For example, some TVsgenerally may not respond to thenext signal right after the Power-on signal. So, a series ofcommands such as TV Power-onand input select may not work
properly.In this case, insert other signals toother components such as in theexample below:TV Power-ontVCR Power-ontVCR playbacktTV input select
To clear programmedcommands
1 Press and while holdingSET, press and hold formore than 3 seconds theSYSTEM CONTROL buttonyou want to clear.
8/11/2019 RMVL600 Remote
32/52
32
Programming aSeries of Commands
on the ComponentSelect Buttons
As with the SYSTEM CONTROLbuttons, you can also program aseries of operating commands forthe Component Select buttons (up
to 16 steps).To execute the commandsprogrammed on a ComponentSelect button by the SystemControl function, press the buttonfor more than 2 seconds.
Notes
When you press the button for lessthan 2 seconds, it works as a normalComponent Select button, and theprogrammed function does not work.
See also Tips for programming theSystem Control functions on page 31.
Example: To program theprocedure on page 29 for the
VCR Component Select button
1 Press and while holdingSET, press the VCRComponent Select button.
SET POWER
SATDVDTV CBL
TAPECDVCR
1
VIDEO1
2
VIDEO2
3
AUX
4
TUNER
5
CD
6
TAPE
7
MD
8
TV
9
PHONO
VOL CH
0
DVD
DIGITAL
/ANALOG
TWIN VIEW
SLEEP
INFO
GUIDE MENU
EXIT TOOLS
SYSTEM CONTROL
RECALLMUTING
AMP
ENT
OK
A B C D
TV/VIDEO
1,3
2
The SET indicator and the VCRComponent Select button lightsturn on.
If a Control Program function(Component Macro) hasalready been set on the button,the button flashes twice. Thesetting procedure isautomatically canceled.
2 Set the Control Programfunction.With this example, press thebuttons in sequence as below:
You can program up to 16consecutive steps on each ofthe Component Select buttons,including the first step of
pressing to select a ComponentSelect button.
3 Press SET to complete theprogramming.The VCR Component Selectbutton light turns off.
SET
SATDVDTV CBL
TAPECD
VCR AMP
POWERTV
1
VCR
POWERPOWER
VCR
AMP
VIDEO1
TV
TV/VIDEO
8/11/2019 RMVL600 Remote
33/52
33
Programming a Series ofCommands on the ComponentSelect Buttons (continued)
To clear programmedcommands
1 Press and while holdingSET, press and hold formore than 3 seconds theComponent Select button
you want to clear.
Notes You can program a Control Program
function (Component Macro) for aComponent Select button on whichthe Power-On function (page 27) has
been programmed. In this case, the
Power-On function is executed whenyou press the Component Selectbutton, or when you select anothercomponent while the consecutiveControl Program is being executed.
If the procedure is interrupted the atany point for over more than 20seconds, the setting mode ends andthe series of commands will be
programmed up to that point. In thiscase, clear the program (page 33) andstart again from Step 1 to set theentire program from the beginning.You cannot continue programmingonce the setting mode ends.
If a Component Select button hasalready learned a remote controlsignal (page 16), you can program aControl Program function
(Component Macro), but the functiondoes will not work until you clear theLearned Function. To clear theLearning Learned Function, seeChanging or erasing the function ofa learned button on page 22.
While you are setting a program, youcan insert a 0.4 second interval beforethe next step is executed by pressing
the same Component Select buttonagain. For the example above in thestep 2, you can insert a 0.4 secondinterval between the TV-on signaland the TV/VIDEO switching signalat the exercising as the program isexecuted by pressing the buttonsTVtPOWERtTV.
Assigning OtherComponents to the
Component SelectButtons
You can assign anothercomponent to any of theComponent Select buttons notbeing used.
Once if you set a ComponentSelect button to a different type ofcomponent, the enteredcomponents code numberbecomes effective.
Notes To use the original component
setting, set the component code
number again (page 10). If you enter a new brands
component code number withoutclearing the previous learnedfunctions on that Component Select
button, the previously learnedfunctions remain effective. Erase thefunctions you do not use frequently.
You can only assign a TV to the TV
Component Select button.
8/11/2019 RMVL600 Remote
34/52
34
1 Press and while holdingPOWER, press TV/VIDEOand CH +.
The SET button and theComponent Select button
currently selected flash once,and the Hold function is set.
While the Hold function is on,no function can be operated.(The SET button and theComponent Select buttoncurrently selected flash twice.)
To unlock the controlPress and while holding POWER,
press TV/VIDEO and CH .The SET button and theComponent Select buttoncurrently selected flash once, andthe Hold function is released.
TV/VIDEOPOWER
CH
+ +
SET
SATDVDTV CBL
TAPECDVCR AMP
SET
SATDVDTV CBL
TAPECDVCR AMP
(twice)
SET
SATDVDTV CBL
TAPECDVCR AMP
(once)
SET
SATDVD
TV CBL
TAPECDVCR AMP
xAll the buttons are locked.
(once)
SET POWER
SATDVDTV CBL
TAPECDVCR
1
VIDEO1
2
VIDEO2
3
AUX
4
TUNER
5
CD
6
TAPE
7
MD
8
TV
9
PHONO
VOL CH
0
DVD
DIGITAL
/ANALOG
TWIN VIEW
SLEEP
INFO
GUIDE MENU
EXIT TOOLS
SYSTEM CONTROL
RECALLMUTING
AMP
ENT
OK
A B C D
TV/VIDEO
1
1
Using Other Functions
Locking the Controls Hold Function
To prevent accidental operation,you can lock all the buttons withthe Hold function.
x
8/11/2019 RMVL600 Remote
35/52
35
1 While holding POWERpressed, press TV/VIDEOand VOL .
When pressing the POWERbutton and the TV/VIDEObutton, all the ComponentSelect buttons go off. Whenpressing the VOL buttonwhile holding down thePOWER button and the TV/
VIDEO button, the SETindicator lights up and theComponent Select buttons lightup one by one. When the SETindicator turns off at last, allsettings are cleared, and theCommander returns to itsoriginal state.
Erasing All Settings To reset the
Commander to itsfactory settings
You can erase all remote controlsignals programmed by thelearned function to reset theCommander to its factory settings.
SET POWER
SATDVDTV CBL
TAPECDVCR
1
VIDEO1
2
VIDEO2
3
AUX
4
TUNER
5
CD
6
TAPE
7
MD
8
TV
9
PHONO
VOL CH
0
DVD
DIGITAL
/ANALOG
TWIN VIEW
SLEEP
INFO
GUIDE MENU
EXIT TOOLS
SYSTEM CONTROL
RECALLMUTING
AMP
ENT
OK
A B C D
TV/VIDEO
1
SET
SATDVD
TV CBL
TAPECDVCR AMP
SET
SATDVDTV CBL
TAPECDVCR AMP
SET
SATDVDTV CBL
TAPECDVCR AMP
SET
SATDVDTV CBL
TAPECDVCR AMP
TV/VIDEOPOWER
VOL
+ +
8/11/2019 RMVL600 Remote
36/52
8/11/2019 RMVL600 Remote
37/52
37
Troubleshooting
If you have problems setting up or using the Remote Commander, first
check the batteries (page 8), then check the items below.Remedy
Move closer to the component. The maximum operatingdistance is approximately 32.8 ft. (10 m).
Check that you are aiming the Commander directly at thecomponent, and that there are no obstructions between theCommander and the component.
Power on the components first, if necessary. Make sure you have pressed the correct Component Select
button. In case of CBL or DVD, make sure the desiredcomponent is selected. Check that the component has infrared remote capability. For
example, if your component didnt come with a remotecommander, it probably isnt capable of being controlled by aremote commander.
You have assigned a different component to the ComponentSelect button. Check the component assigned to that buttonand the component code.
If your visual components are connected to an audio system,
make sure you have set up the Commander as described inControlling the Volume of Visual Components Connected toan Audio System (page 25).
You have assigned another component on the TV or AMPbutton (page 33). In this case, the volume cannot be controlledwhen you select components other than a TV or AMP.
Batteries are weakened.Replace them with new ones.
Set the component code correctly. If the code that is listed firstfor your component does not work, try all the codes for yourcomponent in the order in which they are listed in thesupplied Component Code Numbers.
Some features may not be preset. If some or all of the buttonsdo not function correctly even after you have set thecomponent codes, then use the Learning function to programthe remote control signals for the component (page 16).
The component may be operated with a code number that is
not listed in the Component code numbers. See Setting aComponent Code by the Search Function (page 13) and trysetting a code number again with the Search function.
When you teach signals of an interactive signal exchangesystem remote control unit (supplied with some of Sonysamplifiers) to the Commander, the response signal of themain unit may interfere with the learning of the Commander.In such a case, move to a place where the signals will notreach the main unit (e.g., another room, etc.).
Make sure that the Remote Commander has learned thecorrect signals. If not, see For accurate Learning (page 19)and try the Learning procedure again (page 16).
Symptom
You cannot operatecomponents.
You cannot control the
volume.
The Component Selectbuttons flash by aconstant interval whenyou press a button.
You cannot operate acomponent even aftersetting the componentcode numbers.
The Commander fails tolearn the remote controlsignals.
You cannot operate acomponent even afteryou programmed theremote control signalswith the Learningfunction.
Continued
8/11/2019 RMVL600 Remote
38/52
38
Symptom
The SET indicator flashesfive times during theLearning procedure.
A Component Selectbutton flashes five timesduring setting.
The SET indicator flashestwice during theLearning procedure.
All Component Selectbuttons flash twice.
After programming thePower-On command of acomponent, pressing thatComponent Select buttondoes not functioncorrectly.
The System Controlfunction or ControlProgram function doesnot work properly.
Remedy
Learning has not succeeded. See For accurate Learning(page 19) and try the Learning procedure again (page 16).
There are no available buttons for learning. Clear
infrequently used Learned functions (page 22), then carry outlearning procedure.
The component codes cannot be set. See the suppliedComponent Code Numbers and try setting the componentcodes again (page 10).
A selected Component Select button or another button to beset has any remote control signals programmed by Learningfunction (page 16). Clear the learned signals (page 22) orselect another button which has no learned signals, and try
setting again. The Hold function is on. Unlock the Hold function (page 34).
A Learning function has already been set on the ComponentSelect button. If a Learning function has been set (page 16),you can program the Power-On function on the ComponentSelect button (page 27) but the Power-On setting will notwork until you clear the learned function. Erase thelearned function after the setting the Power-On function.This function is for Sony components only.
When you program a System Control function or ControlProgram function, make sure to follow the correct steps(pages 29, 32).
Change the direction the Remote Commander is aimed. If theproblem persists, position the programmed componentscloser together.
If the remote control receivers of the components are too farapart, or if something is blocking the signals between them,some of the components may not operate in sequence even
after you press the programmed button. If some of thecomponents do not operate correctly because of the above orany other reason, position the components back to the waythey were before you set the System Control function orControl Program function. Failure to do this can result inincorrect operation when you use these functions again.
Some components may not always be powered on by theSystem Control function or Control Program function. This is
because the power of the component turns on and offalternately when receiving the power on/off signal. In this
case, check the operating components power on/off statebefore using the System Control function.
If you change the AV brands component code number (page10) set on a Component Select button that has beenprogrammed for a series of commands by the ControlProgram function, the new signal will be transmitted whenyou press the corresponding Component Select button.
The intervals between steps may be too short. Depending onthe components, you may need to insert an interval betweenconsecutive controls. You can insert an interval by changing
the order of pressing the buttons. (You can insert an intervalbetween steps when programming the Component Selectbutton.)
If a SYSTEM CONTROL button or a Component Select buttonhas already learned a remote control signal (page 16), youcan program a System Control function (System ControlMacro) or a Control Program function (Component Macro),
but the function will not work until you clear the Learnedfunction. To clear the Learned function, see Changing orerasing the function of a learned button on page 22.
For the customers in the U.S.A
Customer Support InformationAfter you have read through this manual, if you still cannot get the RemoteCommander to work properly, call the Sony Customer Support Helplineat 1-800-822-2217.
Troubleshooting (continued)
8/11/2019 RMVL600 Remote
39/52
39
KEY DISPLAY
9POWER
1qaw;1 9, 0, ENT,DOT
q;TV/VIDEO
4INFO(DISPLAY)
qfSLEEP
qhMENU
TV(ANALOG)FUNCTION
To turn on and off.
To change the channel.For example, to changeto channel 5, press 0 and5 (or, press 5 and ENT).
To change the inputmode.
To display the currentchannel on TV.
To operate SLEEPfunction on the TV(works only for a TVwith SLEEP function).
To call up the MENUdisplay.
Appendices
Table of PresetFunctions
NoteThere may be some components orfunctions that cannot be operated with
this Commander.
KEY DISPLAY
qjf
qjF
qjG
qjg
qjOK
qsTWIN VIEW(PIP ON/OFF)
8M
(PIP CH +)
8m(PIP CH )
8RECz(PIP INPUT)
8X
(PIP STILL)8N
(PIP SWAP)
8x(PIP MOVE)
qdCH +/
qgRECALL
3VOL +/
5MUTING
6GUIDE(EPG)
7EXIT
qkTOOLS(OPTION)
FUNCTION
To move the cursorupward.
To move the cursordownward.
To move the cursor tothe right.
To move the cursor tothe left.
To enter the selection ofthe MENU display.
To turn on/off thewindow picture.
To change the TV
channel + in thewindow picture.
To change the TVchannel in thewindow picture.
To change the inputmode of the windowpicture.
To freeze the window
picture.To swap the mainpicture and thewindow picture.
To move the location ofthe windowpicture.
Channel up: +
Channel down:
To operate JUMP,FLASHBACK orCHANNEL RETURNfunction on the TVdepending on the settingof the TVsmanufacturer.
Volume up: +
Volume down:
To mute the volume onthe TV. Press again toturn muting off.
To use the programguide.
To exit the mode.
To go into the OPTIONsetting mode.
SET POWER
SATDVDTV CBL
TAPECDVCR
1
VIDEO1
2
VIDEO2
3
AUX
4
TUNER
5
CD
6
TAPE
7
MD
8
TV
9
PHONO
VOL CH
0
DVD
DIGITAL
/ANALOG
TWIN VIEW
SLEEP
INFO
GUIDE MENU
EXIT TOOLS
SYSTEM CONTROL
RECALLMUTING
AMP
ENT
OK
A B C D
TV/VIDEO
9
0
2
3
4
56
78
1
w;
qs
qa
qd
qf
qgqh
qj
ql
qk
Continued
8/11/2019 RMVL600 Remote
40/52
40
KEY DISPLAY
9POWER
1qaw;1 9, 0, ENT,DOT
q;TV/VIDEO
4INFO(DISPLAY)
qfSLEEP
qhMENU
qjf
qjF
qjG
qjg
qjOK
qsTWIN VIEW(PIP ON/OFF)
8M(VIDEO 3)
8m(VIDEO 1)
8RECz(VIDEO 4)
8X(VIDEO 6)
8N(VIDEO 2)
8x(VIDEO 5)
qdCH +/
qgRECALL
3VOL +/
TV(DIGITAL)FUNCTION
To turn on and off.
To change the channel.For example, to changeto channel 5, press 0 and5 (or, press 5 and ENT).
To change the inputmode.
To display the currentchannel on TV.
To operate the SLEEPfunction on the TV(works only for a TV withthe SLEEP function).
To call up the MENUdisplay.
To move the cursor
upward.To move the cursordownward.
To move the cursor tothe right.
To move the cursor tothe left.
To enter the selection ofthe MENU display.
To turn the windowpicture on/off.
To select the inputsource.VIDEO 3
To select the inputsource.VIDEO 1
To select the inputsource.VIDEO 4
To select the inputsource.VIDEO 6
To select the inputsource.VIDEO 2
To select the inputsource.VIDEO 5
Channel up: +
Channel down:
To operate JUMP,FLASHBACK orCHANNEL RETURNfunction on the TVdepending on the setting
of the TVsmanufacturer.
Volume up: +
Volume down:
Table of Preset Functions(continued)
KEY DISPLAY
5MUTING
6GUIDE(EPG)
7EXIT
2DIGITAL/ANALOG
qkTOOLS
(OPTION)
FUNCTION
To mute the volume onthe TV. Press again toturn muting off.
To use the programguide.
To exit the mode.
To select DIGITAL/ANALOG
To go into the OPTION
setting mode.
8/11/2019 RMVL600 Remote
41/52
41
KEY DISPLAY
9POWER
1qa1 9, 0, ENT
4INFO(DISPLAY)
q;TV/VIDEO(ANT/SW)
qfSLEEP(INPUTSELECT)
qhMENU
qjf
qjF
qjG
qjg
qjOK
8m8N
8M
8RECz
8x
8X
qdCH +/
7EXIT
qgRECALL(DRIVE SELECT)
VCR
FUNCTION
To turn on and off.
To change the channel.For example, to changeto channel 5, press 0 and5 (or, press 5 and ENT).
To expose the on-screendisplay.
To switch the antennaoutput.
To change the inputmode.
To call up the MENUdisplay.
To move the cursorupward.
To move the cursordownward.
To move the cursor tothe right.
To move the cursor tothe left.
To enter the selection ofthe MENU display.
To rewind.To play.
To fast-forward.
To record, pressNwhile pressing RECz*.First releaseN, thenrelease RECz.
To stop.
To pause.
Channel up: +
Channel down:
To exit the mode.
To select the deck.
* In order to avoid recording by
mistake, the RECz
button does notwork by itself.
KEY DISPLAY
9POWER
1qa1 9, 0, ENT
qdCH +/
qgRECALL
CBL (Cable box)FUNCTION
To turn on and off.
To change the channel.For example, to changeto channel 5, press 0 and5 (or , press 5 and ENT.)
Channel up :+
Channel down :
To operate JUMP,FLASHBACK orCHANNEL RETURNfunction.
Continued
8/11/2019 RMVL600 Remote
42/52
8/11/2019 RMVL600 Remote
43/52
43
KEY DISPLAY
9POWER
1qaw;1 9, 0, ENT,DOT
q;TV/VIDEO(INPUT)
4INFO(DISPLAY)
7CLEAR
6GUIDE
(EPG)8m
8N
8M
8RECz
8x
8X
qhMENU
qjf
qjF
qjG
qjg
qfSLEEP(FAVORITE)
qsTWIN VIEW(S. INDEX)
qgRECALL
DVR (Digital video recorder)FUNCTION
To turn on and off.
To change the channel.For example, to changeto channel 5, press 0 and5 (or, press 5 and ENT).
To switch the output ofthe SAT receiver to the
TV. (When connecting aTV cable or antenna tothe receiver, the outputswitches between a TVand SAT program).
To turn on the display.
To clear the setting.
To bring up Master
Guide.To rewind.
To play.
To fast-forward.
To record, pressNwhile pressing RECz*2.First releaseN, thenrelease RECz.
To stop.
To pause.
To call up the MENUdisplay.
To move the cursorupward.
To move the cursordownward.
To move the cursor to
the right.To move the cursor tothe left.
To use the FAVORITEfunction.
To bring up the StationIndex.
To select the channelpreviously selected.
KEY DISPLAY
qjOK
qdCHANNEL
+/
2DIGITAL/ANALOG(REPLAY*1)
FUNCTION
To bring up the StationIndex when a programguide is not displayed.To select the channelthat is highlighted.
Channel up: +
Channel down:
To replayOr to go into REC/REVIEW mode duringplay (After about 5-second rewind, replay
begins).
*1 This key corresponds to Tivo service or
the replay service. Refer to its instruction
manual for details.
*2 In order to avoid recording bymistake, the RECzbutton does notwork by itself.
Continued
8/11/2019 RMVL600 Remote
44/52
44
Table of Preset Functions(continued)
KEY DISPLAY
9POWER
11 9, 0
w;DOT(+10)
qaENTER
qgRECALL(D.SKIP)
8m
8N
8M
8x
8X
qdCH + (>)
qdCH (.)
4INFO(DISPLAY)
6GUIDE(CLEAR)
qkTOOLS(PLAY MODE)
CDFUNCTION
To turn on and off.
To select the tracknumber. 0 selects track10.To select track numbersabove 10, see thedescriptions on the +10
button below.
To select numbers 10and above.
To enter the setting.
To select next disk.
To rewind.
To play.
To fast-forward.
To stop.
To pause.
To select the next track.
To select the previoustrack.
To switch the display ofthe CD player to ON/OFF.
To clear the setting.
To change the playmode cyclically.
KEY DISPLAY
9POWER
11 9, 0
w;DOT(+10)
qaENTER
qgRECALL(D.SKIP)
8m
8N
8M
8RECz
8x
8X
qdCH + (>)
qdCH (.)
4INFO(DISPLAY)
6GUIDE(CLEAR)
qkTOOLS(PLAY MODE)
7EXIT
(REC MODE)qsTWIN VIEW
(CD-SYNC)
MDFUNCTION
To turn on and off.
To select the tracknumber. 0 selects track10.To select track numbersabove 10, see thedescriptions on the +10
button below.
To select numbers 10and above.
To enter the setting.
To select the next disc.
To rewind.
To play.
To fast-forward.
To record, pressNwhile pressing RECz.First releaseN, thenrelease RECz.
To stop.
To pause.
To select the next track.
To select the previous
track.To switch the display ofthe CD player to ON/OFF.
To clear the setting.
To change the playmode cyclically.
To toggle the recording
mode.To start synchronizingwith the CD.
8/11/2019 RMVL600 Remote
45/52
45
KEY DISPLAY
9POWER
8m
8N
w;DOT (n)
8M
8RECz
8x
8X
qgRECALL(A/B)
7EXIT (z)
qjf (N)
qjF (x)
qjG (M)
qjg (m)
qaENT (n)
qkTOOLS (X)
DECKFUNCTION
To turn on and off.
To rewind.
To play.
To reverse.
To fast-forward.
To record, pressNwhile pressing RECz.First releaseN, thenrelease RECz.
To stop.
To pause.
To select the tape deck:Deck A or B (dualcassette deck only).
To record, press fwhile
pressing MENU. Firstrelease f, then releaseMENU.*
To play.*
To stop.*
To fast-forward.*
To rewind.*
To reverse.
To pause.*
KEY DISPLAY
9POWER
11 9, 0
qaENTER
8m
8N
8M
8RECz
8x
8X
qdCH + (>)
qdCH (.)
4INFO(DISPLAY)
DATFUNCTION
To turn on and off.
To select a programnumber.
To enter the setting.
To rewind.
To play.
To fast-forward.To record, pressNwhile pressing RECz.First releaseN, thenrelease RECz.
To stop.
To pause.
To proceed to the nextsong.
To proceed to theprevious song.
To change the displaymode or turn the displayon/off.
* Activated when using a doublecassette deck(for deck A of Sony component)
Continued
KEY DISPLAY
9POWER
11
12
13
14
15
16
17
18
19
10
q;TV/VIDEO(INPUT)
qgRECALL
(SHIFT)qdCH+/
3VOL +/
5MUTING
qaENTER
6GUIDE(BAND)
AMPFUNCTION
To turn on and off.
To select the inputsource: VIDEO 1
To select the inputsource: VIDEO 2
To select the inputsource: AUX
To select the inputsource: TUNER
To select the inputsource: CD
To select the inputsource: TAPE
To select the inputsource: MD
To select the inputsource: TV
To select the inputsource: PHONO
To select the inputsource: DVD
To change the inputselect cyclically.
To shift band or preset
select.Presetting or tuningfrequency up: +
Presetting or tuningfrequency down:
Volume up: +
Volume down:
To mute the volume onthe AMP. Press again to
turn muting off.
To enter the setting.
To select FM/AM.
8/11/2019 RMVL600 Remote
46/52
46
KEY DISPLAY
9POWER
1qa1-9, 0, ENT
q;TV/VIDEO(INPUT)
4INFO
qfSLEEP(Favorite)
6GUIDE
(EPG)qhMENU
qjf
qjF
qjG
qjg
qjOK
qdCH +(PAGE +)
CH (PAGE )
qgRECALL
7EXIT
qkTOOLS(OPTION)
Digital Cable BoxFUNCTION
To turn on and off.
To change the channel.For example, to change tochannel 5, press 0 and 5(or, press 5and ENT).
Select either TV or Cablefor viewing (By pass
mode).Calls up title bar andtoggles title bar on/off.
To switch theFAVORITE TVchannel listprogrammed by acustomer to ON/OFF
To switch the EPG
display to ON/OFF.To call up the MENUdisplay.
To move the cursorupward.
To move the cursordownward.
To move the cursor tothe right.
To move the cursor tothe left.
To command to executefor EPG.
Channel up: +
Channel down:
To toggle the currentchannel/the lastprevious channel.
To exit the setting menu.
To display the functiontag.
KEY DISPLAY
9POWER
11 9, 0
w;DOT(+10)
qaENTER8m
8N
8M
8REC*
8x
8X
qkTOOLS
(TOP MENU)4INFO
(DVDDISPLAY)
qd.
qd>
q;INPUT(TV/VIDEO)
qfSUBTITLE
qjf
qjF
qjG
qjg
qjOK
qhMENU
7EXIT(RETURN)
3VOLUME +
3VOLUME
5MUTING
6GUIDE(CLEAR)
DAV (DVD/Receiver combo)FUNCTION
To turn the power on/off
Number buttons: To setitems selected on thescreen
To select numbers 10and above
To enter the settingTo rewind
To play
To fast-forward
To record
To stop
To pause
To display the Top
MenuTo show the current playstatus on the screen
To proceed to theprevious location orsong
To proceed to the nextlocation or song
To change the inputmode
To switch the subtitle
To move the cursorupward
To move the cursordownward
To move the cursor to
the rightTo move the cursor tothe left
To enter the selection ofthe MENU display
To call up the MENU
To return to the previousdisplay on the MENU
Volume up (DAV)
Volume down (DAV)
To mute the volume.Press again to turnmuting off.
To clear the setting.
Table of Preset Functions(continued)
* To avoid accidental recording, the
REC key does not work unlesspressed for more than 1 second(factory setting).
8/11/2019 RMVL600 Remote
47/52
47
KEY DISPLAY
9POWER
1qaw;1 9, 0, ENT,DOT
4INFO(DISPLAY)
qfSLEEP(FAVORITE)
qhMENU
qjf
qjF
qjG
qjg
qjOK
qdCH +/
qgRECALL
6GUIDE(EPG)
Digital TV TUNERFUNCTION
To turn on and off.
To change the channel.For example, to changeto channel 5, press 0 and5 (or, press 5 and ENT).
To display the currentchannel.
To use the FAVORITEfunction.
To call up the MENUdisplay.
To move the cursorupward.
To move the cursordownward.
To move the cursor tothe right.
To move the cursor tothe left.
To enter the selection ofthe MENU display.
Channel up: +
Channel down:
To operate JUMP,
FLASHBACK orCHANNEL RETURNfunction on the TVdepending on the settingof the TVsmanufacturer.
To use the programguide.
8/11/2019 RMVL600 Remote
48/52
48
Index
A, B
Batteries 8
C, D
Changing 22CH (CHANNEL) button 13Clearing/Changing
learned signal 22, 23Power-On command 27
Code numbers 10, 13
Component Select buttonsassigning other components 33programming a signal 16programming a series of
commands 32setting the Power-On function 27
E
Erasing 35
F, G, H, I, J, K
Factory setting 35
L
Learning Function 16Locking control of the Commander 34
M
MUTING button 12, 15, 19, 26N, O
Number buttons 11, 22
P, Q, R, S
Power-On functionsetting 27
Preset components 10
System Control Functions 29T, U
Troubleshooting 37
V, W, X, Y, Z
VOL buttons 12, 15, 19, 26, 35Volume Control 12, 15, 25
8/11/2019 RMVL600 Remote
49/52
8/11/2019 RMVL600 Remote
50/52
8/11/2019 RMVL600 Remote
51/52
8/11/2019 RMVL600 Remote
52/52