Roll up Door

CHECK GEAR OIL CAPACITY

MAINTAIN AT FILLER PLUG LEVEL

USE A 9/16” OPEN END WRENCH

DIPSTICK FOR GEAR OIL

PLUG

GEAR OIL PLUG LOCATION

GEAR OIL CAPACITY 12 FL. OZ. (GRADE 150)

Roll up Door

WHEN CHAIN BECOMES DIRTY, WASH IN KEROSENE (DO NOT USE GASOLINE OR OTHER SOLVENTS), THEN LUBRICATE WITH A LIGHTWEIGHT MACHINE OIL. READJUST CHAIN FOR PROPER TENSION IF NECESSARY.

LUBRICATE CHAIN AS NEEDED.

Roll up Door

• CHECK ALL BOLTED CONNECTIONS, MAINTAIN CLEAN, TIGHT AND FREE OF CORROSION

Roll up Door

• LUBRICATE SIDE GUIDES

Cord Reel

PULL OUT THE FULL LENGTH OF THE ELECTRICAL CORD REEL AND RETRACT THROUGH A CLEAN RAG LIBERALLY SOAKED WITH SILICONE LUBRICANT.

Cord Reel

INSPECT ALL ELECTRICAL COMPONENETS INSPECT ALL MECHANICAL COMPONENETS

SAFETY LATCH

AIR SHUT-OFF VALVE

REWIND CONTROL VALVE

AIR REWIND MOTOR

Manifolds

• LUBRICATE 2 ZERK FITTINGS EACH OUTLET

ZERK FITTINGS

Camera Connections

1. Connect camera to outlets inside grey box in the Pedestal.

2. Turn Monitors on to channel 31.

3. Turn toggle switch on, Aft plenum toggle is #1 and Pedestal #4, check picture on all 3 Monitors.

4. Lubricate camera connections with Silicone.

1 4

Camera Connections

1. Connect camera to outlets inside grey box in aft plenum

2. Turn Monitors to channel 31.

3. Turn toggle switch on, Aft plenum toggle is #1 and Pedestal is # 4, check picture on all 3 monitors.

4. Lubricate camera connections with Silicone.

1

2

3

MONITOR “ON, OFF”CHANNEL CONTROL

TOGGLE # 1

TOGGLE # 4

Electrical Outlets/Covers

1. LUBRICATE THREADS ON THE COVER

ZERK FITTINGS

Wire Rope WIRE ROPE

• INSPECT ENTIRE LENGTH OF WIRE ROPE. LUBRICATE AS NEEDED.

• LEATHER GLOVES SHOULD BE USED WHEN HANDELING WIRE ROPE.

• WHEN WINDING WINCH CABLE ON THE WINCH DRUM, NEVER ATTEMPT TO MAINTAIN TENSION BY ALLOWING WINCH CABLE TO SLIP THROUGH HANDS. ALWAYS USE “HAND-OVER-HAND” TECHNIQUE.

• THE FORMATION OF KINKS MUST ALWAYS BE PREVENTED AS THIS DISPLACES THE STRANDS OF WIRE FROM THEIR ORIGINAL POSITION & RELATION TO EACH OTHER CAUSING SEVERE BENDING AND UNEQUAL TENSION IN THE STRANDS. THIS DISTORTION AND WIRE DISPLACEMENT CANNOT BE CORRECTED EVEN UNDER HIGH TENSION & A PERMANENT WEAK POINT REMAINS IN THE ROPE. DISPLACED OR RAISED WIRES INDICATE A PREVIOUS KINK, BUT WILL NOT SHOW THE DAMGED CONDITION OF THE INNER ROPE WIRES.

CRANE BOOM LUBRICATION

EXTEND CRANE FULLY. CLEAN ALL FOUR SIDES WITH A DEGREASER. BRUSH ON AMSOIL HEAVY DUTY SYNTHETIC GREASE ON ALL FOUR SIDES. USE POSITIONING PADS AS GUIDES FOR GREASE LINES.

CRANE LUBRICATION

1 2

1. EXTEND CRANE FULLY

2. LUBRICATE ZERK FITTING

LUBRICATING PORT

Crane Basket Outlets

1. MAKE CONNECTIONS TO SUPPLY CRANE BASKET OUTLETS.

2. SILICON CONNECTIONS

3. TEST OUTLETS

ZERK FITTINGS

Tow Reel

1. LUBRICATE ZERK FITTINGS.

2. OPERATE REEL (PULL OUT ENTIRE LENGTH AND AIR REWIND.

ZERK FITTINGS

Bulwark & Deck House Lights

1. LUBRICATE THREADS WITH VASELINE.

2. CLEAN GLASS.

3. 33 BULWARK LIGHTS.

ZERK FITTINGS

Rescue Platform

Wipe Zerk fitting clean with a red rag before lubricating.

Lubricate Zerk fittings on each side of Rescue Platform .

Zerk fittings

Flood Lights

1. LUBRICATE METAL LATCHES.

2. CLEAN INSIDE GLASS AS NEEDED.

ZERK FITTINGS