RF-ECU-2013-C

ROOF WINDOW ELECTRIC OPERATION RETRO FIT KIT

Safety

• The kit must not be used until it has been installed using these instructions.

• The remote control should be kept out of reach of children.

• If repair work is required, disconnect the transformer plug from the mains supply.

• Installation in rooms with high levels of humidity should be in accordance with

relevant electrical regulations.

• Kit is for indoor use only.

• The transformer plug must not be covered (maximum temperature of 40 °C).

IMPORTANT INFORMATION

Function

• This window may be manually operated by removing the pin and clip from the back of the ventilation handle when the window is open or by removing the domed nut on the ventilation handle when closed.

• In case of snow and /or ice, the operation of the window may be obscured.

Product

• The transformer plug must not be removed and mains voltage fed directly to the ECU.

• Disposal of electrical product must be in conformance with national waste regulations.

• The packaging can be disposed as normal household waste.

Maintenance and service

• If installed and operated correctly in accordance with the fitting instructions, the kit does not require any maintenance.

• It is recommended that KEYLITE service engineers carry out any repair work to the window or Keylite electric Kit.

A. Window motor, bracket & cable

B. Blind contact

C. Transformer cable

D. Control panel (ECU)

E. Remote control and holder

F. Transformer plug

G. Rain sensor

FIXING BAG

H. Chain fixing bracket, screw and nut

I. Motor chain retaining pin and clip

J. 15mm screws (x9)

Battery drill

PZ2 Bit

10mm Drill bit

4mm Drill bit

3mm Drill bit

P21 Screwdriver

KIT CONTENTS

TOOLS REQUIRED

2

A

B

C

D

E

G

F

H

I

J

10mm

4mm

3mm

PREPARATION

The blind contactIt is strongly recommended that you install the blind contact even if you do not currently have a blind fitted. Tools required shown on Page 2.

1. Remove the lid from the blind contact by undoing the screw using the P21 screwdriver.

2. Open window using the ventilation handle at the top.

3. Place the blind contact body over the top left hand corner of the sash making sure the contact is pushed towards the locking bolt and the centre of the sash. Using the 3mm drill bit carefully pilot the two holes in the timber.

3

X

X

X30mm

20mm

PREPARATION

4. Secure the blind contact set using two 15mm screws provided. Replace the lid back onto blind contact and secure using screw.

5. Remove the hood flashing from the window frame.

6. Mark point “X” on the plasterboard above the window .

7. Using the 10mm drill bit and power drill carefully drill through the plasterboard at point marked “X” above the window to create a path for the transformer cable. Make note to keep the drill bit parallel with the frame timber when drilling.

4

X

Power supply

8. Take the transformer power cable and feed the white plug on the end through the hole made above the roof window at point “X”.

9. Feed the end of the cable through to the outside of the window.

10. Take the white transformer plug and connect into the “PW” jack on the ECU. Make sure the cable is routed as shown.

Rain sensor

11. Take the blue plug on the end of the rain sensor and connect in to the RS jack on the ECU as shown. Make sure the rain sensor cable is routed as shown.

PREPARATION

5

PREPARATION

12. Turn the ECU around and then fit the rain senor cable down the front using the channel provided.

Fitting the ECU

Once both the transformer and rain sensor have been plugged into the ECU and the cables routed as explained, the ECU is now ready to secure in position.

13. Offer the ECU up to the top left hand corner (from inside) using the two guides on the ECU.

14. Secure the ECU into place with three 15mm screws.

6

Securing the rain sensor

15. Looking from the outside of the window , remove the adhesive patch from the back of the rain sensor and stick it to a clean and dry surface as shown below. Take note that the cable route follows the inside edge of the aluminium channel.

Fixing the window motor

16. Working from inside the room, offer the motor complete with bracket up to the window frame. Make sure the orientation of the bracket and motor is as shown. Align the two tabs either side of the latch keep on the left nearest to the ECU.

N.B. For 1140mm or 1340mm wide windows please remove the right hand latch mechanism

as shown.

17. Secure the motor bracket to the latch timber using 15mm screws and battery drill with PZ2 bit attached.

18. Carefully feed the window motor cable through the route shown and connect green plug into ‘WM’ jack on the ECU.

PREPARATION

7

ON

OFF

Window-Open Blind-Open

Blind-CloseWindow-Close

The remote control operation works on a loop

Open

Stop

Close

Stop

PREPARATION

Programming the remote control

19. Take the transformer plug and connect the jack into the transformer power cable. Connect the transformer plug into the mains and switch on.

20. Turn on the remote control.

21. Press the RC button on the ECU and the LED above the button will flash.

22. Press any button on the remote control and the

LED on the ECU will flash and extinguish. This will be followed by a click from the ECU. The remote control is now programmed.

8

118mm

20mm

Y

Attaching the motor chain to the window

23. Mark a point shown as “Y” on the back of the ventilation handle foam at the top of the window as shown.

24. Using a battery drill and the 4mm drill bit carefully drill through the foam of the ventilation handle and the back section. Stop when the drill bit is visible from the inside. Make sure drill bit is at right angles to the ventilation handle.

25. Place the bracket onto the foam of the ventilation handle over the hole. Place the bolt though the hole. Compressing the foam with the bracket until the threads of the bolt are visible from wire. Attach the domed nut to the thread as shown.

PREPARATION

9

PREPARATION

26. Press the button on the remote control to extend the chain from the motor.

27. When the motor chain is fully extended connect to the ventilation handle using clip and pin.

28. Press the button on the remote control to close the window.

The window is now connected and operable via the remote control.

10