Rope Kit Labels

Version 2019-05-01

www.waszp.com

Trolley Tie Down Assembly - RFC211MK1 X2 (Cleats) - S/T 10-6 X 1 1/4” - B/R Red Rope 800mm X2 - M8 Washers X2 - WZHTDSH Tie Down Hooks X2

To Fit:

1. Put stopper knot under trolley pad making sure to slide washer onto the end so the knot does not pull through the trolley pad

2. Use screws provided to attach Cleat to pre-drilled holes

3. Thread rope through hook and then through the cleats putting a stopper knot at the end

02 www.waszp.com

GPS Mount

- WZGPSX GPS Mount assembly - BO5x40SH (M5x40 SS Cap Bolt) - BO5W x2 (M5 Washer)

Bungs inc rubber washers x 2

03 www.waszp.com

Top pin for wing mounts

- WZWPO x 4 (Wing outer Pin) - ROB2 0.2m x 4 (2mm Bungee)

www.waszp.com

04

Wing Cover Ties

- ROD3 2.9m x 2 (3mm Dyneema Grey)

05 www.waszp.com

05 Foot Strap Ties

- ROD3 1.5m x 2 (3mm Dyneema Grey)

Tie a 10cm loop then twice around the wing bar

through that loop. Make sure you go through the

webbing positioning strap.

The standard footstraps work very well if tight. Make

sure you put some tension on them to position the

rope on the front wing bar before tensioning the

tramps.

www.waszp.com 06

Tiller centreing and Rudder bungee

- 2x ROB8 0.75m (8mm Bungee)

www.waszp.com 07

Rope to pull rudder down.

- ROCL4K 1.35m (Control Rope 4mm black) - ROB2 1.2m (Bungee 2mm)

www.waszp.com 08

Bungee and ties for wand forward tension

- ROB8 0.6m (8mm Bungee) - ROD2G 0.5m (2mm Dyneema)

(cut after tied one end)

www.waszp.com 09

Ride Height Adjuster Control Cord

- ROD2Y 5.25m (2mm Dyneema Yellow)

www.waszp.com 10

Ropes and pulleys for Downhaul.

- ROCL4K 5.9m (4mm Control Rope Black) - ROB4 1.3m x2 (4mm Bungee) - RF13101-2 x2 (Kite Block) - HK406 (16mm Double Block)(mast) - RF1806 (4mm Std Shackle) - HK408 (16mm Triple Block)(sail) - RF616 (5mm Std Shackle)

www.waszp.com

11

Outhaul control line - to sailor

- ROCL4R 6m (4mm Control Rope Red) - RF13101-2 x2 (Kite Block) - ROB4 1.2m x2 (4mm Bungee)(beside outer wing bar)

12 www.waszp.com

Clew pulleys

- HK406 x2 (16mm double block) - RF621 (Long 4mm D Shackle) (for sail) - ROD2G 0.3m (Dyneema 2mm Grey) (for boom)

13 www.waszp.com

Outhaul control line - to boom

- ROCL4R 3.4m (4mm Control Rope Red) - ROB4 1.7m (4mm Bungee) (along hull centre)

14 www.waszp.com

Mainsheet

- ROM7 7.1m (DS-7)

www.waszp.com 15

Mainsheet bridle

- RF30101 (30mm Single Loop Block) - RF616 (Std 5mm D shackle) - ROD3 x3 (spliced bridle ropes) (longer to rear)

16 www.waszp.com

Mainsheet blocks for sail (tied to webbing blocks)

- RF35101 x2 (Ronstan Orbit Block 30) - ROD2G 0.3m x2 (Dyneema 2mm Grey)

www.waszp.com

17

Mainsheet Block (Tied to tramps)

- RF46101 (Ronstan Orbit Ratchet Block) - ROCL4K 0.3m (4mm Control Rope Black) - BOW5 x2 (M5 washer)

www.waszp.com 18

Mainsheet catcher

- ROB2 1.8m (2mm bungee) (Goes from rear wing corner through ring on rudder pin to other rear wing corner. Stops mainsheet catching on wing bars)

www.waszp.com 19

Boom to Mast

- Spliced 3mm Dyneema

www.waszp.com 20

Spares Kit

- 1 x WZWSFUR Wing support front up right

- 1 x WZWSFUL Wing support front up left

- 1 x WZWSRU Wing support rear up

- 1 x WZWSFDR Wing support front down right

- 1 x WZWSFDL Wing support front down left

- 2 x WZWSRD Wing support rear down

- 4 x ATCS30 Cam Spacer

- 1 x BO1-4x10P 1/4"-20 Plastic Bolt (Bung)

- 1 x BO3x6GS M3x6mm Grub Screw

- 1 x BO3x8RHP M3x8mm Round Head Bolt Phillip

- 1 x M2FFRP Foil Retaining Pin

- 1 x WZFB Waszp foil joiner bolt

- 1 x WZHBREEF Bolt rope end stopper front -

1 x WZWSMP Wing support lower pin - 1 x

WZWSUP Wing support upper pin

www.waszp.com 21