21
RT Software tOG GV Sports and K2 Dyno S Olaf Bahr, Product Manager Grass Valley, a Belden Brand. July 2015

RT Software tOG GV Sports and K2 Dyno S - Grass Valley · ALICAION NO RT SOFTWARE TOG GV SPORTS AND K2 DNO S 3 Installation on K2 Dyno S 1) If the K2 Dyno application is running,

  • Upload
    others

  • View
    5

  • Download
    0

Embed Size (px)

Citation preview

RT Software tOG GV Sports and K2 Dyno S Olaf Bahr Product Manager Grass Valley a Belden Brand

July 2015

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

2wwwgrassvalleycom

WHY tOG ON K2 DYNO S

The speed of live events and the need to efficiently tell the story of ldquowhat just happenedrdquo is increasingly in demand to be faster more dynamic paint a clearer picture and even be more entertaining to enhance the viewing experience The integration of tOG and K2 Dyno brings an affordable A-level analysis tool to every level of live event production

This Application Note covers

bull Software installation and setup on K2 Dyno S

bull Software installation and setup on the tOG PC

bull Preparing the K2 Summit 3G for interaction with tOG

bull Using the K2 Dyno StOG interface

bull Building stacked overlay graphics

Prior to using this Application Note verify with the K2 Dyno S K2 Summit 3G and tOG release notes that the appropriately compati-ble versions of software on all systems is being used Visit the Grass Valley K2 Dyno website for updated information regarding software releases required software and documentation wwwgrassvalleycomproductsk2_dyno and click on the Documentation tab in the Resources area

Required software for K2 Dyno installation in the RTDyno_Installzip file

ChromeStandaloneSetupexe

GoogleUpdateadm

tOGGVDynoClientcrx

tOGGVDynoClientpem

Required software for tOG Server installation

togpre-46_14565-windows-installer

tog-46_r15288-windows-installer

mysql-5535-winx64

dvsdriver-4354_1-windows-installer

gvsports-46_r15288-windows-installer

Have the IP address subnet mask and any other IP configuration information readily available for the K2 Dyno S K2 Summit 3G and tOG server In either a standalone or SAN configuration the K2 Dyno S K2 Summit 3G and tOG server need to be connected via a Gigabit Ethernet switch or router

For this Application Note example the IP addresses are

K2 Summit 3G 10164170

K2 Dyno S 10164171

tOG server PC 10164179

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

3wwwgrassvalleycom

Installation on K2 Dyno S

1) If the K2 Dyno application is running exit the application to the K2 Dyno S Mainte-nance level in order to see the Windows desktop

2) Verify that McAfee Embedded Security Manager is set to UPDATE

3) If not connected connect the K2 Dyno S Controller to the Internet via the Media Port on the back

4) Insert a USB device with the RTDyno_Install files

5) Run the ChromeStandaloneSetupexe

6) With an Internet connection Chrome will install on the K2 Dyno S controller Close the Chrome Browser application From this point Internet connection is no lon-ger required

7) To prevent Chrome from automatically downloading and installing updates that have not been tested in this environment it is advised the following adjustments to Chrome are made Use Windows Start menu and type in Edit group policy

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

4wwwgrassvalleycom

Installation on K2 Dyno S (cont)

8) From the selection click on Edit group policy When the window opens under User Configuration right-click on Administrative Templates then AddRemove Templates

9) Click Addhellip and browse to the RTDyno_Install folder that contains the file GoogleUpdateadm and select it and click Open

10) If it is listed in the window of tem-plates close the window

11) Under Computer Configuration select Administrative TemplatesClas-sic Administrative TemplatesGoogleGoogle UpdateApplications Google Chrome

12) In this folder right-click on Update policy override and select Edit

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

5wwwgrassvalleycom

Installation on K2 Dyno S (cont)

13) Change Update policy override to Enabled and Policy to Updates disabled

14) Then click Apply and then OK close all windows

15) Open a Chrome browser window and type in the URL search field chromeextensions This will open the Chrome extensions setup section

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

6wwwgrassvalleycom

Installation on K2 Dyno S (cont)

16) With Windows Explorer open the RTDyno_Install folder and drag the tOGGVDynoClientcrx file onto the Chrome Browser window

17) In the Chrome Browser Apps tab is the RT Software Client app Right-click and select Create shortcutshellip

hellipand only check the Desktop box Then click Create Now close the Chrome browser The RT Software Client shortcut will be created on the desktop (NOTE Do Not check add to Start Menu or Pin to Taskbar this will create an incorrect shortcut)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

7wwwgrassvalleycom

Installation on K2 Dyno S (cont)

18) On the K2 Dyno S desktop right-click and create a new text file

19) Name the file the IP address of the tOG server PC and include the txt suf-fix (For this example the IP address is 10164179 therefore the file name would be 10164179txt Please remember to substitute your IP address for the example given)

20) Right-click on the RT Software Client short-cut and select Properties

21) In the Target field there should be a sim-ilar line to this ldquoCProgram Files (x86)GoogleChromeApplicationchromeexerdquo --profile-directory=Default --app-id=hdin-gebnoinafgkhbbdfdfobnanfopjo

22) At the end of this string add a single space and then ldquocUsersAdministratorDesk-top10164179txtrdquo Then click Apply and OK (Note Do not forget the quotation marks and to substitute your IP address for the example given above)

23) If the IP address of the tOG server PC changes in the future the txt file name and the target line above both need to be changed as well

24) After these settings are complete it is acceptable to add the shortcut to the Win-dows Taskbar

25) Once installation is complete ENABLE McAfee Embedded Security by selecting Leave Update Mode

26) Restart the K2 Dyno S controller

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

8wwwgrassvalleycom

Installation on K2 Summit 3G

1) Launch AppCenter on the on the K2 Summit 3G

2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder

3) At the top of AppCenter select the Control tab and then Optionshellip

4) In the side tabs select Control and button check Remote and Local and AMP

5) Click OK

6) Do this for each channel to be con-trolled

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

9wwwgrassvalleycom

Installation on tOG Server

MySQL Installation

1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures

2) Prior to installation the operating system has to be installed Current versions supported are

RedHat EL 55 Workstation 64-bit

Windows 7 Pro 64-bit SP1

3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are

Linux ndash 33120

Windows ndash 33182

4) Refer to the documentation associated with the selected driver for install instructions

Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at

wwwmysqlcomdownloadsmysql

This is the community edition and is available for free under the Open Source GPL license

1) Double click on the installer

2) Click Next

3) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

10wwwgrassvalleycom

MySQL Installation (cont)

4) Typical is the setup type to be installed Click Next

5) Click Install

7) Click Next

6) MySQL will now install

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

11wwwgrassvalleycom

MySQL Installation (cont)

8) Click Next

11) Click Next

9) Click Finish

10) MySQL will now launch the MySQL Instance configurator

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

12wwwgrassvalleycom

MySQL Installation (cont)

12) Select Standard Configuration then Click Next

15) IMPORTANT Deselect the Modify Secu-rity Settings

16) Click Next

13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH

14) Click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

13wwwgrassvalleycom

MySQL Installation (cont)

17) MySQL service is ready to execute the con-figuration

18) Click Execute to finalize the installation and configuration of MySQL

19) Click Finish when the service is complete then close all open windows

20) Run the tOG Pre install application

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

14wwwgrassvalleycom

MySQL Installation (cont)

23) Click Finish to complete the installation

24) Run the tOG install application

25) Accept the EULA and click Next

26) Use the default installation directory loca-tion and click Next

27) Click Finish to complete the installation

28) Run the GV Sports Install application

29) Accept the EULA and click Next

30) Use the default Installation Directory loca-tion and click Next

31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next

32) Click Next again to start the install

33) Click Finish to complete the installation

34) On the desktop is a folder with the tOG ver-sion name

22) Use the default Installation Directory loca-tion and click Next

21) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

2wwwgrassvalleycom

WHY tOG ON K2 DYNO S

The speed of live events and the need to efficiently tell the story of ldquowhat just happenedrdquo is increasingly in demand to be faster more dynamic paint a clearer picture and even be more entertaining to enhance the viewing experience The integration of tOG and K2 Dyno brings an affordable A-level analysis tool to every level of live event production

This Application Note covers

bull Software installation and setup on K2 Dyno S

bull Software installation and setup on the tOG PC

bull Preparing the K2 Summit 3G for interaction with tOG

bull Using the K2 Dyno StOG interface

bull Building stacked overlay graphics

Prior to using this Application Note verify with the K2 Dyno S K2 Summit 3G and tOG release notes that the appropriately compati-ble versions of software on all systems is being used Visit the Grass Valley K2 Dyno website for updated information regarding software releases required software and documentation wwwgrassvalleycomproductsk2_dyno and click on the Documentation tab in the Resources area

Required software for K2 Dyno installation in the RTDyno_Installzip file

ChromeStandaloneSetupexe

GoogleUpdateadm

tOGGVDynoClientcrx

tOGGVDynoClientpem

Required software for tOG Server installation

togpre-46_14565-windows-installer

tog-46_r15288-windows-installer

mysql-5535-winx64

dvsdriver-4354_1-windows-installer

gvsports-46_r15288-windows-installer

Have the IP address subnet mask and any other IP configuration information readily available for the K2 Dyno S K2 Summit 3G and tOG server In either a standalone or SAN configuration the K2 Dyno S K2 Summit 3G and tOG server need to be connected via a Gigabit Ethernet switch or router

For this Application Note example the IP addresses are

K2 Summit 3G 10164170

K2 Dyno S 10164171

tOG server PC 10164179

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

3wwwgrassvalleycom

Installation on K2 Dyno S

1) If the K2 Dyno application is running exit the application to the K2 Dyno S Mainte-nance level in order to see the Windows desktop

2) Verify that McAfee Embedded Security Manager is set to UPDATE

3) If not connected connect the K2 Dyno S Controller to the Internet via the Media Port on the back

4) Insert a USB device with the RTDyno_Install files

5) Run the ChromeStandaloneSetupexe

6) With an Internet connection Chrome will install on the K2 Dyno S controller Close the Chrome Browser application From this point Internet connection is no lon-ger required

7) To prevent Chrome from automatically downloading and installing updates that have not been tested in this environment it is advised the following adjustments to Chrome are made Use Windows Start menu and type in Edit group policy

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

4wwwgrassvalleycom

Installation on K2 Dyno S (cont)

8) From the selection click on Edit group policy When the window opens under User Configuration right-click on Administrative Templates then AddRemove Templates

9) Click Addhellip and browse to the RTDyno_Install folder that contains the file GoogleUpdateadm and select it and click Open

10) If it is listed in the window of tem-plates close the window

11) Under Computer Configuration select Administrative TemplatesClas-sic Administrative TemplatesGoogleGoogle UpdateApplications Google Chrome

12) In this folder right-click on Update policy override and select Edit

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

5wwwgrassvalleycom

Installation on K2 Dyno S (cont)

13) Change Update policy override to Enabled and Policy to Updates disabled

14) Then click Apply and then OK close all windows

15) Open a Chrome browser window and type in the URL search field chromeextensions This will open the Chrome extensions setup section

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

6wwwgrassvalleycom

Installation on K2 Dyno S (cont)

16) With Windows Explorer open the RTDyno_Install folder and drag the tOGGVDynoClientcrx file onto the Chrome Browser window

17) In the Chrome Browser Apps tab is the RT Software Client app Right-click and select Create shortcutshellip

hellipand only check the Desktop box Then click Create Now close the Chrome browser The RT Software Client shortcut will be created on the desktop (NOTE Do Not check add to Start Menu or Pin to Taskbar this will create an incorrect shortcut)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

7wwwgrassvalleycom

Installation on K2 Dyno S (cont)

18) On the K2 Dyno S desktop right-click and create a new text file

19) Name the file the IP address of the tOG server PC and include the txt suf-fix (For this example the IP address is 10164179 therefore the file name would be 10164179txt Please remember to substitute your IP address for the example given)

20) Right-click on the RT Software Client short-cut and select Properties

21) In the Target field there should be a sim-ilar line to this ldquoCProgram Files (x86)GoogleChromeApplicationchromeexerdquo --profile-directory=Default --app-id=hdin-gebnoinafgkhbbdfdfobnanfopjo

22) At the end of this string add a single space and then ldquocUsersAdministratorDesk-top10164179txtrdquo Then click Apply and OK (Note Do not forget the quotation marks and to substitute your IP address for the example given above)

23) If the IP address of the tOG server PC changes in the future the txt file name and the target line above both need to be changed as well

24) After these settings are complete it is acceptable to add the shortcut to the Win-dows Taskbar

25) Once installation is complete ENABLE McAfee Embedded Security by selecting Leave Update Mode

26) Restart the K2 Dyno S controller

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

8wwwgrassvalleycom

Installation on K2 Summit 3G

1) Launch AppCenter on the on the K2 Summit 3G

2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder

3) At the top of AppCenter select the Control tab and then Optionshellip

4) In the side tabs select Control and button check Remote and Local and AMP

5) Click OK

6) Do this for each channel to be con-trolled

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

9wwwgrassvalleycom

Installation on tOG Server

MySQL Installation

1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures

2) Prior to installation the operating system has to be installed Current versions supported are

RedHat EL 55 Workstation 64-bit

Windows 7 Pro 64-bit SP1

3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are

Linux ndash 33120

Windows ndash 33182

4) Refer to the documentation associated with the selected driver for install instructions

Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at

wwwmysqlcomdownloadsmysql

This is the community edition and is available for free under the Open Source GPL license

1) Double click on the installer

2) Click Next

3) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

10wwwgrassvalleycom

MySQL Installation (cont)

4) Typical is the setup type to be installed Click Next

5) Click Install

7) Click Next

6) MySQL will now install

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

11wwwgrassvalleycom

MySQL Installation (cont)

8) Click Next

11) Click Next

9) Click Finish

10) MySQL will now launch the MySQL Instance configurator

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

12wwwgrassvalleycom

MySQL Installation (cont)

12) Select Standard Configuration then Click Next

15) IMPORTANT Deselect the Modify Secu-rity Settings

16) Click Next

13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH

14) Click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

13wwwgrassvalleycom

MySQL Installation (cont)

17) MySQL service is ready to execute the con-figuration

18) Click Execute to finalize the installation and configuration of MySQL

19) Click Finish when the service is complete then close all open windows

20) Run the tOG Pre install application

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

14wwwgrassvalleycom

MySQL Installation (cont)

23) Click Finish to complete the installation

24) Run the tOG install application

25) Accept the EULA and click Next

26) Use the default installation directory loca-tion and click Next

27) Click Finish to complete the installation

28) Run the GV Sports Install application

29) Accept the EULA and click Next

30) Use the default Installation Directory loca-tion and click Next

31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next

32) Click Next again to start the install

33) Click Finish to complete the installation

34) On the desktop is a folder with the tOG ver-sion name

22) Use the default Installation Directory loca-tion and click Next

21) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

3wwwgrassvalleycom

Installation on K2 Dyno S

1) If the K2 Dyno application is running exit the application to the K2 Dyno S Mainte-nance level in order to see the Windows desktop

2) Verify that McAfee Embedded Security Manager is set to UPDATE

3) If not connected connect the K2 Dyno S Controller to the Internet via the Media Port on the back

4) Insert a USB device with the RTDyno_Install files

5) Run the ChromeStandaloneSetupexe

6) With an Internet connection Chrome will install on the K2 Dyno S controller Close the Chrome Browser application From this point Internet connection is no lon-ger required

7) To prevent Chrome from automatically downloading and installing updates that have not been tested in this environment it is advised the following adjustments to Chrome are made Use Windows Start menu and type in Edit group policy

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

4wwwgrassvalleycom

Installation on K2 Dyno S (cont)

8) From the selection click on Edit group policy When the window opens under User Configuration right-click on Administrative Templates then AddRemove Templates

9) Click Addhellip and browse to the RTDyno_Install folder that contains the file GoogleUpdateadm and select it and click Open

10) If it is listed in the window of tem-plates close the window

11) Under Computer Configuration select Administrative TemplatesClas-sic Administrative TemplatesGoogleGoogle UpdateApplications Google Chrome

12) In this folder right-click on Update policy override and select Edit

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

5wwwgrassvalleycom

Installation on K2 Dyno S (cont)

13) Change Update policy override to Enabled and Policy to Updates disabled

14) Then click Apply and then OK close all windows

15) Open a Chrome browser window and type in the URL search field chromeextensions This will open the Chrome extensions setup section

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

6wwwgrassvalleycom

Installation on K2 Dyno S (cont)

16) With Windows Explorer open the RTDyno_Install folder and drag the tOGGVDynoClientcrx file onto the Chrome Browser window

17) In the Chrome Browser Apps tab is the RT Software Client app Right-click and select Create shortcutshellip

hellipand only check the Desktop box Then click Create Now close the Chrome browser The RT Software Client shortcut will be created on the desktop (NOTE Do Not check add to Start Menu or Pin to Taskbar this will create an incorrect shortcut)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

7wwwgrassvalleycom

Installation on K2 Dyno S (cont)

18) On the K2 Dyno S desktop right-click and create a new text file

19) Name the file the IP address of the tOG server PC and include the txt suf-fix (For this example the IP address is 10164179 therefore the file name would be 10164179txt Please remember to substitute your IP address for the example given)

20) Right-click on the RT Software Client short-cut and select Properties

21) In the Target field there should be a sim-ilar line to this ldquoCProgram Files (x86)GoogleChromeApplicationchromeexerdquo --profile-directory=Default --app-id=hdin-gebnoinafgkhbbdfdfobnanfopjo

22) At the end of this string add a single space and then ldquocUsersAdministratorDesk-top10164179txtrdquo Then click Apply and OK (Note Do not forget the quotation marks and to substitute your IP address for the example given above)

23) If the IP address of the tOG server PC changes in the future the txt file name and the target line above both need to be changed as well

24) After these settings are complete it is acceptable to add the shortcut to the Win-dows Taskbar

25) Once installation is complete ENABLE McAfee Embedded Security by selecting Leave Update Mode

26) Restart the K2 Dyno S controller

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

8wwwgrassvalleycom

Installation on K2 Summit 3G

1) Launch AppCenter on the on the K2 Summit 3G

2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder

3) At the top of AppCenter select the Control tab and then Optionshellip

4) In the side tabs select Control and button check Remote and Local and AMP

5) Click OK

6) Do this for each channel to be con-trolled

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

9wwwgrassvalleycom

Installation on tOG Server

MySQL Installation

1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures

2) Prior to installation the operating system has to be installed Current versions supported are

RedHat EL 55 Workstation 64-bit

Windows 7 Pro 64-bit SP1

3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are

Linux ndash 33120

Windows ndash 33182

4) Refer to the documentation associated with the selected driver for install instructions

Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at

wwwmysqlcomdownloadsmysql

This is the community edition and is available for free under the Open Source GPL license

1) Double click on the installer

2) Click Next

3) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

10wwwgrassvalleycom

MySQL Installation (cont)

4) Typical is the setup type to be installed Click Next

5) Click Install

7) Click Next

6) MySQL will now install

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

11wwwgrassvalleycom

MySQL Installation (cont)

8) Click Next

11) Click Next

9) Click Finish

10) MySQL will now launch the MySQL Instance configurator

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

12wwwgrassvalleycom

MySQL Installation (cont)

12) Select Standard Configuration then Click Next

15) IMPORTANT Deselect the Modify Secu-rity Settings

16) Click Next

13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH

14) Click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

13wwwgrassvalleycom

MySQL Installation (cont)

17) MySQL service is ready to execute the con-figuration

18) Click Execute to finalize the installation and configuration of MySQL

19) Click Finish when the service is complete then close all open windows

20) Run the tOG Pre install application

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

14wwwgrassvalleycom

MySQL Installation (cont)

23) Click Finish to complete the installation

24) Run the tOG install application

25) Accept the EULA and click Next

26) Use the default installation directory loca-tion and click Next

27) Click Finish to complete the installation

28) Run the GV Sports Install application

29) Accept the EULA and click Next

30) Use the default Installation Directory loca-tion and click Next

31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next

32) Click Next again to start the install

33) Click Finish to complete the installation

34) On the desktop is a folder with the tOG ver-sion name

22) Use the default Installation Directory loca-tion and click Next

21) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

4wwwgrassvalleycom

Installation on K2 Dyno S (cont)

8) From the selection click on Edit group policy When the window opens under User Configuration right-click on Administrative Templates then AddRemove Templates

9) Click Addhellip and browse to the RTDyno_Install folder that contains the file GoogleUpdateadm and select it and click Open

10) If it is listed in the window of tem-plates close the window

11) Under Computer Configuration select Administrative TemplatesClas-sic Administrative TemplatesGoogleGoogle UpdateApplications Google Chrome

12) In this folder right-click on Update policy override and select Edit

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

5wwwgrassvalleycom

Installation on K2 Dyno S (cont)

13) Change Update policy override to Enabled and Policy to Updates disabled

14) Then click Apply and then OK close all windows

15) Open a Chrome browser window and type in the URL search field chromeextensions This will open the Chrome extensions setup section

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

6wwwgrassvalleycom

Installation on K2 Dyno S (cont)

16) With Windows Explorer open the RTDyno_Install folder and drag the tOGGVDynoClientcrx file onto the Chrome Browser window

17) In the Chrome Browser Apps tab is the RT Software Client app Right-click and select Create shortcutshellip

hellipand only check the Desktop box Then click Create Now close the Chrome browser The RT Software Client shortcut will be created on the desktop (NOTE Do Not check add to Start Menu or Pin to Taskbar this will create an incorrect shortcut)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

7wwwgrassvalleycom

Installation on K2 Dyno S (cont)

18) On the K2 Dyno S desktop right-click and create a new text file

19) Name the file the IP address of the tOG server PC and include the txt suf-fix (For this example the IP address is 10164179 therefore the file name would be 10164179txt Please remember to substitute your IP address for the example given)

20) Right-click on the RT Software Client short-cut and select Properties

21) In the Target field there should be a sim-ilar line to this ldquoCProgram Files (x86)GoogleChromeApplicationchromeexerdquo --profile-directory=Default --app-id=hdin-gebnoinafgkhbbdfdfobnanfopjo

22) At the end of this string add a single space and then ldquocUsersAdministratorDesk-top10164179txtrdquo Then click Apply and OK (Note Do not forget the quotation marks and to substitute your IP address for the example given above)

23) If the IP address of the tOG server PC changes in the future the txt file name and the target line above both need to be changed as well

24) After these settings are complete it is acceptable to add the shortcut to the Win-dows Taskbar

25) Once installation is complete ENABLE McAfee Embedded Security by selecting Leave Update Mode

26) Restart the K2 Dyno S controller

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

8wwwgrassvalleycom

Installation on K2 Summit 3G

1) Launch AppCenter on the on the K2 Summit 3G

2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder

3) At the top of AppCenter select the Control tab and then Optionshellip

4) In the side tabs select Control and button check Remote and Local and AMP

5) Click OK

6) Do this for each channel to be con-trolled

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

9wwwgrassvalleycom

Installation on tOG Server

MySQL Installation

1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures

2) Prior to installation the operating system has to be installed Current versions supported are

RedHat EL 55 Workstation 64-bit

Windows 7 Pro 64-bit SP1

3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are

Linux ndash 33120

Windows ndash 33182

4) Refer to the documentation associated with the selected driver for install instructions

Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at

wwwmysqlcomdownloadsmysql

This is the community edition and is available for free under the Open Source GPL license

1) Double click on the installer

2) Click Next

3) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

10wwwgrassvalleycom

MySQL Installation (cont)

4) Typical is the setup type to be installed Click Next

5) Click Install

7) Click Next

6) MySQL will now install

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

11wwwgrassvalleycom

MySQL Installation (cont)

8) Click Next

11) Click Next

9) Click Finish

10) MySQL will now launch the MySQL Instance configurator

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

12wwwgrassvalleycom

MySQL Installation (cont)

12) Select Standard Configuration then Click Next

15) IMPORTANT Deselect the Modify Secu-rity Settings

16) Click Next

13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH

14) Click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

13wwwgrassvalleycom

MySQL Installation (cont)

17) MySQL service is ready to execute the con-figuration

18) Click Execute to finalize the installation and configuration of MySQL

19) Click Finish when the service is complete then close all open windows

20) Run the tOG Pre install application

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

14wwwgrassvalleycom

MySQL Installation (cont)

23) Click Finish to complete the installation

24) Run the tOG install application

25) Accept the EULA and click Next

26) Use the default installation directory loca-tion and click Next

27) Click Finish to complete the installation

28) Run the GV Sports Install application

29) Accept the EULA and click Next

30) Use the default Installation Directory loca-tion and click Next

31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next

32) Click Next again to start the install

33) Click Finish to complete the installation

34) On the desktop is a folder with the tOG ver-sion name

22) Use the default Installation Directory loca-tion and click Next

21) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

5wwwgrassvalleycom

Installation on K2 Dyno S (cont)

13) Change Update policy override to Enabled and Policy to Updates disabled

14) Then click Apply and then OK close all windows

15) Open a Chrome browser window and type in the URL search field chromeextensions This will open the Chrome extensions setup section

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

6wwwgrassvalleycom

Installation on K2 Dyno S (cont)

16) With Windows Explorer open the RTDyno_Install folder and drag the tOGGVDynoClientcrx file onto the Chrome Browser window

17) In the Chrome Browser Apps tab is the RT Software Client app Right-click and select Create shortcutshellip

hellipand only check the Desktop box Then click Create Now close the Chrome browser The RT Software Client shortcut will be created on the desktop (NOTE Do Not check add to Start Menu or Pin to Taskbar this will create an incorrect shortcut)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

7wwwgrassvalleycom

Installation on K2 Dyno S (cont)

18) On the K2 Dyno S desktop right-click and create a new text file

19) Name the file the IP address of the tOG server PC and include the txt suf-fix (For this example the IP address is 10164179 therefore the file name would be 10164179txt Please remember to substitute your IP address for the example given)

20) Right-click on the RT Software Client short-cut and select Properties

21) In the Target field there should be a sim-ilar line to this ldquoCProgram Files (x86)GoogleChromeApplicationchromeexerdquo --profile-directory=Default --app-id=hdin-gebnoinafgkhbbdfdfobnanfopjo

22) At the end of this string add a single space and then ldquocUsersAdministratorDesk-top10164179txtrdquo Then click Apply and OK (Note Do not forget the quotation marks and to substitute your IP address for the example given above)

23) If the IP address of the tOG server PC changes in the future the txt file name and the target line above both need to be changed as well

24) After these settings are complete it is acceptable to add the shortcut to the Win-dows Taskbar

25) Once installation is complete ENABLE McAfee Embedded Security by selecting Leave Update Mode

26) Restart the K2 Dyno S controller

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

8wwwgrassvalleycom

Installation on K2 Summit 3G

1) Launch AppCenter on the on the K2 Summit 3G

2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder

3) At the top of AppCenter select the Control tab and then Optionshellip

4) In the side tabs select Control and button check Remote and Local and AMP

5) Click OK

6) Do this for each channel to be con-trolled

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

9wwwgrassvalleycom

Installation on tOG Server

MySQL Installation

1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures

2) Prior to installation the operating system has to be installed Current versions supported are

RedHat EL 55 Workstation 64-bit

Windows 7 Pro 64-bit SP1

3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are

Linux ndash 33120

Windows ndash 33182

4) Refer to the documentation associated with the selected driver for install instructions

Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at

wwwmysqlcomdownloadsmysql

This is the community edition and is available for free under the Open Source GPL license

1) Double click on the installer

2) Click Next

3) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

10wwwgrassvalleycom

MySQL Installation (cont)

4) Typical is the setup type to be installed Click Next

5) Click Install

7) Click Next

6) MySQL will now install

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

11wwwgrassvalleycom

MySQL Installation (cont)

8) Click Next

11) Click Next

9) Click Finish

10) MySQL will now launch the MySQL Instance configurator

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

12wwwgrassvalleycom

MySQL Installation (cont)

12) Select Standard Configuration then Click Next

15) IMPORTANT Deselect the Modify Secu-rity Settings

16) Click Next

13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH

14) Click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

13wwwgrassvalleycom

MySQL Installation (cont)

17) MySQL service is ready to execute the con-figuration

18) Click Execute to finalize the installation and configuration of MySQL

19) Click Finish when the service is complete then close all open windows

20) Run the tOG Pre install application

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

14wwwgrassvalleycom

MySQL Installation (cont)

23) Click Finish to complete the installation

24) Run the tOG install application

25) Accept the EULA and click Next

26) Use the default installation directory loca-tion and click Next

27) Click Finish to complete the installation

28) Run the GV Sports Install application

29) Accept the EULA and click Next

30) Use the default Installation Directory loca-tion and click Next

31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next

32) Click Next again to start the install

33) Click Finish to complete the installation

34) On the desktop is a folder with the tOG ver-sion name

22) Use the default Installation Directory loca-tion and click Next

21) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

6wwwgrassvalleycom

Installation on K2 Dyno S (cont)

16) With Windows Explorer open the RTDyno_Install folder and drag the tOGGVDynoClientcrx file onto the Chrome Browser window

17) In the Chrome Browser Apps tab is the RT Software Client app Right-click and select Create shortcutshellip

hellipand only check the Desktop box Then click Create Now close the Chrome browser The RT Software Client shortcut will be created on the desktop (NOTE Do Not check add to Start Menu or Pin to Taskbar this will create an incorrect shortcut)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

7wwwgrassvalleycom

Installation on K2 Dyno S (cont)

18) On the K2 Dyno S desktop right-click and create a new text file

19) Name the file the IP address of the tOG server PC and include the txt suf-fix (For this example the IP address is 10164179 therefore the file name would be 10164179txt Please remember to substitute your IP address for the example given)

20) Right-click on the RT Software Client short-cut and select Properties

21) In the Target field there should be a sim-ilar line to this ldquoCProgram Files (x86)GoogleChromeApplicationchromeexerdquo --profile-directory=Default --app-id=hdin-gebnoinafgkhbbdfdfobnanfopjo

22) At the end of this string add a single space and then ldquocUsersAdministratorDesk-top10164179txtrdquo Then click Apply and OK (Note Do not forget the quotation marks and to substitute your IP address for the example given above)

23) If the IP address of the tOG server PC changes in the future the txt file name and the target line above both need to be changed as well

24) After these settings are complete it is acceptable to add the shortcut to the Win-dows Taskbar

25) Once installation is complete ENABLE McAfee Embedded Security by selecting Leave Update Mode

26) Restart the K2 Dyno S controller

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

8wwwgrassvalleycom

Installation on K2 Summit 3G

1) Launch AppCenter on the on the K2 Summit 3G

2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder

3) At the top of AppCenter select the Control tab and then Optionshellip

4) In the side tabs select Control and button check Remote and Local and AMP

5) Click OK

6) Do this for each channel to be con-trolled

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

9wwwgrassvalleycom

Installation on tOG Server

MySQL Installation

1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures

2) Prior to installation the operating system has to be installed Current versions supported are

RedHat EL 55 Workstation 64-bit

Windows 7 Pro 64-bit SP1

3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are

Linux ndash 33120

Windows ndash 33182

4) Refer to the documentation associated with the selected driver for install instructions

Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at

wwwmysqlcomdownloadsmysql

This is the community edition and is available for free under the Open Source GPL license

1) Double click on the installer

2) Click Next

3) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

10wwwgrassvalleycom

MySQL Installation (cont)

4) Typical is the setup type to be installed Click Next

5) Click Install

7) Click Next

6) MySQL will now install

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

11wwwgrassvalleycom

MySQL Installation (cont)

8) Click Next

11) Click Next

9) Click Finish

10) MySQL will now launch the MySQL Instance configurator

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

12wwwgrassvalleycom

MySQL Installation (cont)

12) Select Standard Configuration then Click Next

15) IMPORTANT Deselect the Modify Secu-rity Settings

16) Click Next

13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH

14) Click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

13wwwgrassvalleycom

MySQL Installation (cont)

17) MySQL service is ready to execute the con-figuration

18) Click Execute to finalize the installation and configuration of MySQL

19) Click Finish when the service is complete then close all open windows

20) Run the tOG Pre install application

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

14wwwgrassvalleycom

MySQL Installation (cont)

23) Click Finish to complete the installation

24) Run the tOG install application

25) Accept the EULA and click Next

26) Use the default installation directory loca-tion and click Next

27) Click Finish to complete the installation

28) Run the GV Sports Install application

29) Accept the EULA and click Next

30) Use the default Installation Directory loca-tion and click Next

31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next

32) Click Next again to start the install

33) Click Finish to complete the installation

34) On the desktop is a folder with the tOG ver-sion name

22) Use the default Installation Directory loca-tion and click Next

21) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

7wwwgrassvalleycom

Installation on K2 Dyno S (cont)

18) On the K2 Dyno S desktop right-click and create a new text file

19) Name the file the IP address of the tOG server PC and include the txt suf-fix (For this example the IP address is 10164179 therefore the file name would be 10164179txt Please remember to substitute your IP address for the example given)

20) Right-click on the RT Software Client short-cut and select Properties

21) In the Target field there should be a sim-ilar line to this ldquoCProgram Files (x86)GoogleChromeApplicationchromeexerdquo --profile-directory=Default --app-id=hdin-gebnoinafgkhbbdfdfobnanfopjo

22) At the end of this string add a single space and then ldquocUsersAdministratorDesk-top10164179txtrdquo Then click Apply and OK (Note Do not forget the quotation marks and to substitute your IP address for the example given above)

23) If the IP address of the tOG server PC changes in the future the txt file name and the target line above both need to be changed as well

24) After these settings are complete it is acceptable to add the shortcut to the Win-dows Taskbar

25) Once installation is complete ENABLE McAfee Embedded Security by selecting Leave Update Mode

26) Restart the K2 Dyno S controller

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

8wwwgrassvalleycom

Installation on K2 Summit 3G

1) Launch AppCenter on the on the K2 Summit 3G

2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder

3) At the top of AppCenter select the Control tab and then Optionshellip

4) In the side tabs select Control and button check Remote and Local and AMP

5) Click OK

6) Do this for each channel to be con-trolled

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

9wwwgrassvalleycom

Installation on tOG Server

MySQL Installation

1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures

2) Prior to installation the operating system has to be installed Current versions supported are

RedHat EL 55 Workstation 64-bit

Windows 7 Pro 64-bit SP1

3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are

Linux ndash 33120

Windows ndash 33182

4) Refer to the documentation associated with the selected driver for install instructions

Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at

wwwmysqlcomdownloadsmysql

This is the community edition and is available for free under the Open Source GPL license

1) Double click on the installer

2) Click Next

3) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

10wwwgrassvalleycom

MySQL Installation (cont)

4) Typical is the setup type to be installed Click Next

5) Click Install

7) Click Next

6) MySQL will now install

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

11wwwgrassvalleycom

MySQL Installation (cont)

8) Click Next

11) Click Next

9) Click Finish

10) MySQL will now launch the MySQL Instance configurator

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

12wwwgrassvalleycom

MySQL Installation (cont)

12) Select Standard Configuration then Click Next

15) IMPORTANT Deselect the Modify Secu-rity Settings

16) Click Next

13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH

14) Click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

13wwwgrassvalleycom

MySQL Installation (cont)

17) MySQL service is ready to execute the con-figuration

18) Click Execute to finalize the installation and configuration of MySQL

19) Click Finish when the service is complete then close all open windows

20) Run the tOG Pre install application

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

14wwwgrassvalleycom

MySQL Installation (cont)

23) Click Finish to complete the installation

24) Run the tOG install application

25) Accept the EULA and click Next

26) Use the default installation directory loca-tion and click Next

27) Click Finish to complete the installation

28) Run the GV Sports Install application

29) Accept the EULA and click Next

30) Use the default Installation Directory loca-tion and click Next

31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next

32) Click Next again to start the install

33) Click Finish to complete the installation

34) On the desktop is a folder with the tOG ver-sion name

22) Use the default Installation Directory loca-tion and click Next

21) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

8wwwgrassvalleycom

Installation on K2 Summit 3G

1) Launch AppCenter on the on the K2 Summit 3G

2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder

3) At the top of AppCenter select the Control tab and then Optionshellip

4) In the side tabs select Control and button check Remote and Local and AMP

5) Click OK

6) Do this for each channel to be con-trolled

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

9wwwgrassvalleycom

Installation on tOG Server

MySQL Installation

1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures

2) Prior to installation the operating system has to be installed Current versions supported are

RedHat EL 55 Workstation 64-bit

Windows 7 Pro 64-bit SP1

3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are

Linux ndash 33120

Windows ndash 33182

4) Refer to the documentation associated with the selected driver for install instructions

Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at

wwwmysqlcomdownloadsmysql

This is the community edition and is available for free under the Open Source GPL license

1) Double click on the installer

2) Click Next

3) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

10wwwgrassvalleycom

MySQL Installation (cont)

4) Typical is the setup type to be installed Click Next

5) Click Install

7) Click Next

6) MySQL will now install

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

11wwwgrassvalleycom

MySQL Installation (cont)

8) Click Next

11) Click Next

9) Click Finish

10) MySQL will now launch the MySQL Instance configurator

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

12wwwgrassvalleycom

MySQL Installation (cont)

12) Select Standard Configuration then Click Next

15) IMPORTANT Deselect the Modify Secu-rity Settings

16) Click Next

13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH

14) Click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

13wwwgrassvalleycom

MySQL Installation (cont)

17) MySQL service is ready to execute the con-figuration

18) Click Execute to finalize the installation and configuration of MySQL

19) Click Finish when the service is complete then close all open windows

20) Run the tOG Pre install application

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

14wwwgrassvalleycom

MySQL Installation (cont)

23) Click Finish to complete the installation

24) Run the tOG install application

25) Accept the EULA and click Next

26) Use the default installation directory loca-tion and click Next

27) Click Finish to complete the installation

28) Run the GV Sports Install application

29) Accept the EULA and click Next

30) Use the default Installation Directory loca-tion and click Next

31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next

32) Click Next again to start the install

33) Click Finish to complete the installation

34) On the desktop is a folder with the tOG ver-sion name

22) Use the default Installation Directory loca-tion and click Next

21) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

9wwwgrassvalleycom

Installation on tOG Server

MySQL Installation

1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures

2) Prior to installation the operating system has to be installed Current versions supported are

RedHat EL 55 Workstation 64-bit

Windows 7 Pro 64-bit SP1

3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are

Linux ndash 33120

Windows ndash 33182

4) Refer to the documentation associated with the selected driver for install instructions

Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at

wwwmysqlcomdownloadsmysql

This is the community edition and is available for free under the Open Source GPL license

1) Double click on the installer

2) Click Next

3) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

10wwwgrassvalleycom

MySQL Installation (cont)

4) Typical is the setup type to be installed Click Next

5) Click Install

7) Click Next

6) MySQL will now install

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

11wwwgrassvalleycom

MySQL Installation (cont)

8) Click Next

11) Click Next

9) Click Finish

10) MySQL will now launch the MySQL Instance configurator

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

12wwwgrassvalleycom

MySQL Installation (cont)

12) Select Standard Configuration then Click Next

15) IMPORTANT Deselect the Modify Secu-rity Settings

16) Click Next

13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH

14) Click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

13wwwgrassvalleycom

MySQL Installation (cont)

17) MySQL service is ready to execute the con-figuration

18) Click Execute to finalize the installation and configuration of MySQL

19) Click Finish when the service is complete then close all open windows

20) Run the tOG Pre install application

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

14wwwgrassvalleycom

MySQL Installation (cont)

23) Click Finish to complete the installation

24) Run the tOG install application

25) Accept the EULA and click Next

26) Use the default installation directory loca-tion and click Next

27) Click Finish to complete the installation

28) Run the GV Sports Install application

29) Accept the EULA and click Next

30) Use the default Installation Directory loca-tion and click Next

31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next

32) Click Next again to start the install

33) Click Finish to complete the installation

34) On the desktop is a folder with the tOG ver-sion name

22) Use the default Installation Directory loca-tion and click Next

21) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

10wwwgrassvalleycom

MySQL Installation (cont)

4) Typical is the setup type to be installed Click Next

5) Click Install

7) Click Next

6) MySQL will now install

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

11wwwgrassvalleycom

MySQL Installation (cont)

8) Click Next

11) Click Next

9) Click Finish

10) MySQL will now launch the MySQL Instance configurator

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

12wwwgrassvalleycom

MySQL Installation (cont)

12) Select Standard Configuration then Click Next

15) IMPORTANT Deselect the Modify Secu-rity Settings

16) Click Next

13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH

14) Click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

13wwwgrassvalleycom

MySQL Installation (cont)

17) MySQL service is ready to execute the con-figuration

18) Click Execute to finalize the installation and configuration of MySQL

19) Click Finish when the service is complete then close all open windows

20) Run the tOG Pre install application

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

14wwwgrassvalleycom

MySQL Installation (cont)

23) Click Finish to complete the installation

24) Run the tOG install application

25) Accept the EULA and click Next

26) Use the default installation directory loca-tion and click Next

27) Click Finish to complete the installation

28) Run the GV Sports Install application

29) Accept the EULA and click Next

30) Use the default Installation Directory loca-tion and click Next

31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next

32) Click Next again to start the install

33) Click Finish to complete the installation

34) On the desktop is a folder with the tOG ver-sion name

22) Use the default Installation Directory loca-tion and click Next

21) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

11wwwgrassvalleycom

MySQL Installation (cont)

8) Click Next

11) Click Next

9) Click Finish

10) MySQL will now launch the MySQL Instance configurator

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

12wwwgrassvalleycom

MySQL Installation (cont)

12) Select Standard Configuration then Click Next

15) IMPORTANT Deselect the Modify Secu-rity Settings

16) Click Next

13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH

14) Click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

13wwwgrassvalleycom

MySQL Installation (cont)

17) MySQL service is ready to execute the con-figuration

18) Click Execute to finalize the installation and configuration of MySQL

19) Click Finish when the service is complete then close all open windows

20) Run the tOG Pre install application

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

14wwwgrassvalleycom

MySQL Installation (cont)

23) Click Finish to complete the installation

24) Run the tOG install application

25) Accept the EULA and click Next

26) Use the default installation directory loca-tion and click Next

27) Click Finish to complete the installation

28) Run the GV Sports Install application

29) Accept the EULA and click Next

30) Use the default Installation Directory loca-tion and click Next

31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next

32) Click Next again to start the install

33) Click Finish to complete the installation

34) On the desktop is a folder with the tOG ver-sion name

22) Use the default Installation Directory loca-tion and click Next

21) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

12wwwgrassvalleycom

MySQL Installation (cont)

12) Select Standard Configuration then Click Next

15) IMPORTANT Deselect the Modify Secu-rity Settings

16) Click Next

13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH

14) Click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

13wwwgrassvalleycom

MySQL Installation (cont)

17) MySQL service is ready to execute the con-figuration

18) Click Execute to finalize the installation and configuration of MySQL

19) Click Finish when the service is complete then close all open windows

20) Run the tOG Pre install application

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

14wwwgrassvalleycom

MySQL Installation (cont)

23) Click Finish to complete the installation

24) Run the tOG install application

25) Accept the EULA and click Next

26) Use the default installation directory loca-tion and click Next

27) Click Finish to complete the installation

28) Run the GV Sports Install application

29) Accept the EULA and click Next

30) Use the default Installation Directory loca-tion and click Next

31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next

32) Click Next again to start the install

33) Click Finish to complete the installation

34) On the desktop is a folder with the tOG ver-sion name

22) Use the default Installation Directory loca-tion and click Next

21) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

13wwwgrassvalleycom

MySQL Installation (cont)

17) MySQL service is ready to execute the con-figuration

18) Click Execute to finalize the installation and configuration of MySQL

19) Click Finish when the service is complete then close all open windows

20) Run the tOG Pre install application

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

14wwwgrassvalleycom

MySQL Installation (cont)

23) Click Finish to complete the installation

24) Run the tOG install application

25) Accept the EULA and click Next

26) Use the default installation directory loca-tion and click Next

27) Click Finish to complete the installation

28) Run the GV Sports Install application

29) Accept the EULA and click Next

30) Use the default Installation Directory loca-tion and click Next

31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next

32) Click Next again to start the install

33) Click Finish to complete the installation

34) On the desktop is a folder with the tOG ver-sion name

22) Use the default Installation Directory loca-tion and click Next

21) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

14wwwgrassvalleycom

MySQL Installation (cont)

23) Click Finish to complete the installation

24) Run the tOG install application

25) Accept the EULA and click Next

26) Use the default installation directory loca-tion and click Next

27) Click Finish to complete the installation

28) Run the GV Sports Install application

29) Accept the EULA and click Next

30) Use the default Installation Directory loca-tion and click Next

31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next

32) Click Next again to start the install

33) Click Finish to complete the installation

34) On the desktop is a folder with the tOG ver-sion name

22) Use the default Installation Directory loca-tion and click Next

21) Accept the EULA and click Next

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

15wwwgrassvalleycom

MySQL Installation (cont)

36) The GV Sports shortcut can be copied to the desktop

37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server

38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server

39) Launch GV Sports with the desktop shortcut

35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall

40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab

41) Under Clip Control Plugin select K2DirClipStore

42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)

43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)

44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels

45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels

46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

16wwwgrassvalleycom

MySQL Installation (cont)

48) From the right hand panel of tabs select tOG Preferences

49) Under the Protocol tab None should be the Protocol setting

50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes

47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List

51) Under the Video tab choose the input and output device settings

52) If using the split screen tool the Number of Channels on the input side should be set to 2

53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter

54) Click Save to save any changes

55) Exit the tOG application and relaunch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

17wwwgrassvalleycom

MySQL Installation (cont)

56) IMPORTANT Xitami Web Server service must be stopped on the tOG server

Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server

57) Right-click Properties and under Gen-eral tab Startup type set to Disable

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

18wwwgrassvalleycom

MySQL Installation (cont)

58) Then ensure Service Status is STOPPED Click Apply and close the window

59) Next verify the Windows Firewall is turned OFF

60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing

61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process

62) Close all windows

63) Restart the tOG server

64) Launch with the GV Sports shortcut

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

19wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller

1) Start a replay session with the K2 Dyno S and start recording

2) Launch the tOG application on the tOG server

3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface

4) Click Show Tools in the bottom-left corner to expose the tools

6) Click Clips in the upper-right to access clips on the K2 Summit

5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

20wwwgrassvalleycom

Using the tOG Application on K2 Dyno S Controller (cont)

7) Double tap a clip to load it to the K2 Summit output channel

8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen

9) Use the Restart button at the top to recue the clip and the overlay graphic clears

10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe

11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack

12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point

13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen

14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg

21

APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S

Appendix

1) Double click on the DVS driver installer

2) Click Next

3) Accept the EULA and click Next

4) Use the default Installation Directory loca-tion and click Next

5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows

6) Windows Power Save Mode

If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER

Service Help

Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care

GVB-1-0105C-EN-AN

This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents

Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein

Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice

WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn

wwwgrassvalleycomblog

reg