-
DET NORSKE VERITAS
TYPE APPROVAL CERTIFICATE
CERTIFICATE N. S-5264
his Certificate consists of 4 pages his is to certify that
the
Lifting Set for Offshore Containers wth type designation(s)
Master Links and Master Link Assemblies, Type M
and MT Manufactured by
GUNNEBO INDUSTRIER AB
RAMNS, Sweden is found to comply with
DNV 2.7-1 Offshore Containers
EN 12079-2 Offshore containers and associated lifting sets Part
2: Lifting sets Design,
manufacture and marking
IMO/MSC Circular 860
EN 1677-4 Components for slings - Safety - Part 4: Links, Grade
8
Application Grade 10 Links
for Lifting Sets for Offshore Containers
Place and date This Certificate is valid until
Hvik, 2008-06-04 2012-06-30
for Det Norske Veritas
AS
Per Esvall Local Office Alexandre Gerszt
Head of Section DNV Stockholm Surveyor
-
Product description
Links for use in Lifting Sets for Offshore Containers certified
to DNV 2.7-1 Offshore
Containers.
Detailed product information and range of certified products
covered by this Type
Approval are listed in Appendix 1 of this Type Approval
Certificate.
Application/Limitation
For application of links the minimum Working Load Limit (WLL)
shall be decided
according to the strength requirements for lifting sets on
offshore containers as given
in DNV 2.7-1 Offshore Containers, Chapter 8.
Tests to be carried out:
- Production testing: According to DNV Standard for
Certification No. 2.7-1
and EN standard EN 1677-4 "Components for slings Safety - Part
4; Links,
Grade 8" in agreement with the DNV surveyor.
- Material to be impact tested by Charpy impact method according
to DNV
2.7-1 Offshore Containers, Chapter 8.4.
All products manufactured according to this TA shall be
inspected by a DNV
surveyor, and in addition the DNV surveyor shall witness the
production testing and
issue certificates for each batch, according to DNV 2.7-1
Offshore Containers,
Chapter 8 and Appendix K.
Type Approval documentation
Tests carried out
Prototype strength tested according to Rules.
Marking of product
Each item to be marked according to EN 1677-1, "Components for
slings - Safety -
Part 1: Forged steel components, Grade 8".
Certificate retention survey
For retention of Type Approval, a DNV surveyor shall perform a
survey every
2nd
year and before the expiry date of this certificate to verify
that the type approval is
complied with.
END OF CERTIFICATE
-
Appendix 1
Product description and details
Master links type M (dwg T00036/P01):
Type Dia.
[mm]
WLL
[t]
MPF
[kN]
Min. BF
[kN]
M-13-10 OFFS 19 5,4 132 212
M-1310-10 OFFS 22 7,8 161 306
M-1613-10 OFFS 28 10,6 260 416
M-281-10 OFFS 28 10,6 260 416
M-19-10 OFFS 30 11,9 292 467
M-321-10 OFFS 32 14,1 346 553
S-16-10 OFFS 32 14,6 358 573
M-381-10 OFFS 40 20,9 513 820
M-2220-10 OFFS 40 23,1 567 906
M-32-10 OFFS 45 33 809 1295
M-3226-10 OFFS 50 44 1079 1727
M-3632-10 OFFS 55 55 1349 2158
Master link assemblies type MT (dwg T00037/P01):
Type Dia.
[mm]
WLL
[t]
MPF
[kN]
Min. BF
[kN]
MT-9-10 OFFS 28 7,8 191 306
MT-281-10 OFFS 28 10,6 260 416
MT-321-10 OFFS 32 14,1 346 553
MT-381-10 OFFS 40 20,9 513 820
MT-20-10 OFFS 55 33 809 1295
Notice: This Certificate is subject to terms and conditions
overleaf. Any significant change in design or construction may
render this
Certificate invalid.
If any person suffers loss or damage which is proved to have
been caused by any negligent act or omission of Det Norske Verit
as, then Det Norske Veritas shall pay compensation to such person
for his proved direct loss or damage. However, the compensation
shall not exceed an amount equal to ten times the fee charged for
the service in question, provided that the maximum compensation
shall never exceed USD 2 million.In this provision "Det Norske
Veritas" shall mean the Foundation Det Norske Veritas as well as
all its subsidiaries,
directors, officers, employees, agents and any other acting on
behalf of Det Norske Veritas.
