N!~1-!9NY'...~.b"~ ..' C p...,

NELSON STUD WELDINGSPECIFICATION S3L Shear Connectors (SC)

Nelson headed shear connectors deliver code specified shear strength values asused in composite construction, securing concrete to steel structuralcomponents. Nelson shear connectors meet requirements ofthe tOllowingcodes and are also USNRC approved:

AWS Dl.l Structural Welding Code - SteelAWS D1.6 Structural Welding Code - Stainless SteelAWS D1.5 Bridge Welding Code 1

AASHTO Standard Specification tOrHighway BridgesISO-139l8 welding - Studs tOrarc stud weldingCanadianStandardsAssociationW59 - Welded SteelConstructionInternational Building Code Section 19AlSC Manual of Steel Construction - Allowable Stress DesignAlSC Manual of Steel Construction - Load & Resistance Factor Design

See also: ICBO Evaluation Report ER-26l4 Nelson Shear Connectors

J Ched. StalldardStocL

u1.!~n9th

I

I

i

,---1

Shear connectors are typically used in composite steel construction tOrholding concrete slabs to steel members to resistshear tOrcesand increase shear loading capacity in steel buildings, bridges, columns caissons, containment liners, etc.They also act as embedment anchors on miscellaneous embedded plates, funnes, angles, strip plates, attachments andconnections. Options tOrWelding Through Metal Deck are available fur this stud.

For similar function studs, see Nelson H4L Headed Concrete Anchors and D2L DefoID1edBar Anchors.

When ordering, specify Ill!!:, Diameter, Length, Material, Quantity, and Part Number

* Burn Off: Burn off lengths shown are for welding to bare steel. For burn off values and other details when studs are welded

through metal deckto steel see WELD THROUGH DECK SPECIFICA nON SHEET

The Nelson Ferrule Shooter is available tOrsemi-automatic dispensing ofceran1ic fuules along with standard fuulesassembled 50 pieces per" string" tOreasy and fast loading onto the Ferrule Shooter dispenser. Following are the currentferrule assemblies available:

MATERIALS: Studs are available in Low Carbon Mild Steel and 316L Stainless Steel. For specific grade iniOnnation

and physical and chemical properties, conlOnning standards, and iniOnnation on stud plating and heat treating, pleasesee General Material Specifications. Certified Material Test Reports (CMTR) and Certificates of Compliance (COe) areavailable and must be requested at time of order.For fuules and grips used in welding at an angle to plate, welding to angles, and welding to a vertical base plate, seethe Special Applications section ofthe Femlle Specifications.

Visit our website www.NelsonStudWelding.com fur a list of our standard stock products.

Nelson Stud Walding, Inc.

7900 Wast Ridge Road

Elyria. Ohio 44035

PH 1-800-NEL-VllELD1-800-635-9353

E-rrail: Nelson.Sales@NelsonStud.com

3/02

1!.Xam Ie: /s,jL ,j/"l x 6-3/16"; lVJllO .Heel; 10,000 pieces; ff.lU.lU:;IOU.l;:J

Stud Burn Recommended Standard AccessoriesDiameter Off A H Chuck Foot Ferrule Holder Ferrule for Flat

3/4" 0.187 0.375 1.250 500001 088 502002042 501006027 10010115219 rrm 4rrm718' 0.187 0.375 1.375 500001091 502002042 501006028 100101140

22rrm 4rrm1" 0.250 0.500 1.625 500001424 502002042 501 006046 100101045

25mm 6rrm

Stud diameter Ferrule

314" dov.nhand 100101260

314" Vleldthrong h deck 100101249

71ef'dov.nhand 100101261

71ef'Vleldthroug h deck 100101262