Salus RT200 Manual 002:89 23/11/10 11:05 Page 1 Electronic

Instruction ManualModel No RT200

Electronic Room Thermostat

2

Salus RT200 Manual 002:89 23/11/10 11:05 Page 1

RT200 INSTRUCTION MANUAL2

PRODUCT COMPLIANCEThis product complies with the essential requirements of the following ECDirectives:• Electro-Magnetic Compatibility directive 2004/108/EC• Low Voltage Directive 2006/95/EEC• EC Marking directive 93/68/EEC

SAFETY INFORMATIONThese instructions are applicable to the Salus Controls model stated on thefront cover of this manual only, and must not be used with any other make ormodel.

These instructions are intended to apply in the United Kingdom only, andshould be followed along with any other statutory obligations.

This accessory must be fitted by a Competent person, and installation mustcomply with the guidance provided in the current editions of BS7671 (IEEWiring Regulations) and Part ‘P’ of the Building Regulations. Failure tocomply with the requirements of these publications could lead toprosecution.

Always isolate the AC Mains supply before carrying out any work on theRT200 thermostat.

Please leave these instructions with the end user where they should be keptin a safe place for future reference.


RT200 INSTRUCTION MANUAL 3

INTRODUCTIONA thermostat is a device that is used to switchthe heating system in your home on and off asneeded. It works by sensing the airtemperature and switching on the heatingwhen the air temperature falls below thethermostat setting, and switching it off oncethe set temperature has been reached.

The RT200 from Salus Controls is a stylish andaccurate electronic thermostat with a large,easy to adjust setting dial. The thermostat hasbeen specifically designed to be used in 230VAC heating applications.

Features• Simple to use• Large dial• Stylish Casing• LED heat call indicator• Temperature range between 5 ºC and 35 ºC

OPERATIONThe RT200 is adjusted very easily by turning the rotary dial on the front ofthe thermostat to the required temperature setting. To adjust the settemperature, turn the rotary dial to the left to set a lower temperature, or tothe right to set a higher temperature.

The Light Emitting Diode (LED) on the front panel will light when thetemperature is below the set value, showing that the thermostat is calling forheat from the boiler. Once the room reaches the set temperature, the LEDwill turn off and the RT200 will stop calling for heat from the boiler.


INSTALLATIONPlease read the important safety information at the start of this manual before youbegin to install the thermostat.The ideal position to locate the RT200 thermostat is about 1.5m above floor level, ina location where the thermostat is accessible, reasonably lit and free from extremes oftemperature and draughts. Do not mount the thermostat on an outside wall, above aradiator or in a location where it may be subjected to direct sunlight.The electrical connections to the RT200 are made to the supplied industry standardbackplate. This simplifies installation, as no connections are made to the controlleritself. Connection details are shown below - no Earth connection is required for thecorrect and safe operation of the RT200, but a parking terminal is provided to connectan Earth wire if one is present.


Backplate Connections

Terminal Description BackplateN Mains NeutralL Mains Live

SL Switched Live (Normally Open Contact)Earth Parking (no electrical connection)

After installing the backplate in a suitable location, wiring connections can be made as shown above. The following criteria apply to the installation:• The incoming AC mains supply should be 230V AC and fused at 5 amps.• Optimum cable size for installation is 1.5 mm2; wiring colours should be in

accordance with the current requirements of the IEE Wiring Regulations.• Cable entry should be from the rear of the backplate.• All wiring connections should be securely made, and be firmly gripped

beneath the square brass washer on each terminal.



Do not restore the mains supply to the system until all associated items are fully installed.NOTE: All electrical installation work should be carried out by a suitably qualified Electricianor other competent person. If you are not sure how to install this thermostat consult eitherwith a qualified electrician, heating engineer or your boiler / heating system supplier foradvice on how to continue.Do not remove or refit the RT200 onto the backplate without the mains supply tothe system being isolated.

ENERGY TIPOne way to set and use your room thermostat is to find the lowest temperature settingthat you are comfortable with, and then leave it set at this temperature. You can dothis by setting the room thermostat to a low temperature, (for example 17 °C) andthen increasing the setting by one degree each day until you are comfortable withthe room temperature - you won’t have to adjust the thermostat further, asadjustment above this setting will waste energy - a 1 °C increase in temperature isequal to 3% of your heating costs.

MAINTENANCEThe RT200 thermostat requires no special maintenance. Periodically, the outer casingcan be wiped clean using a dry cloth (please DO NOT use solvents, polishes, detergentsor abrasive cleaners, as these can damage the thermostat).There are no user serviceable parts within the unit; any servicing or repairs shouldonly be carried out by Salus Controls or their appointed agents.Should the RT200 thermostat fail to function correctly, check:• The RT200 temperature has been set correctly.• Heating system time switch or programmer is switched on.

WARRANTYSalus Controls warrants that this product will be free from any defect in materials orworkmanship, and shall perform in accordance with its specification, for a period oftwo years from the date of purchase. Salus Controls sole liability for breach of thiswarranty will be (at its option) to repair or replace the defective product.


PRODUCT SPECIFICATIONModel: RT200Type: Surface mounted electronic room

thermostat designed for 230V ACheating applications.

SwitchingSwitching Voltage: 230V AC / 50HzSwitching Current: 3A resistive, 1A inductiveContact Type: Single Pole Single Throw (SPST)

TemperatureRange: 5 ºC to 35 ºCAccuracy: ± 1 ºC at 25 ºC

EnvironmentOperating Temperature: 0 ºC to + 50 ºCStorage Temperature: - 20 ºC to + 55 ºC



Salus Controls warrants that this product will be free from any defect in materials orworkmanship, and shall perform in accordance with its specification, for a period oftwo years from the date of purchase. Salus Controls sole liability for breach of thiswarranty will be (at its option) to repair or replace the defective product.

RT200 Warranty

Customer Name: ..............................................................

Customer Address: ...........................................................

.........................................................................................

Post Code: ......................... Tel No: ..................................

Email: ...............................................................................

Engineers Company: ........................................................

Tel No: .............................................................................

Email: ...............................................................................

Intallation Date: ...............................................................

Engineers Name: ..............................................................

Engineers Signature: ........................................................



Email: [email protected] Tel: 01226 323961Email: [email protected] Tel: 01226 323961

Sales:Technical:

Salus Controls plc, Salus House, Dodworth Business Park South,Whinby Road, Dodworth, Barnsley S75 3SP

salus-tech.


Documents

Salus RT200 Manual 002:89 23/11/10 11:05 Page 1 Electronic