Samsung™ Tablet Install Guide

©2021 Trimble Inc. All rights reserved. Unauthorized duplication prohibited. Trimble and the Globe & Triangle Logo are trademarks of Trimble Inc. registered in the United States Patent and Trademark Office and/or in other countries. All other trademarks are the property of their respective owners.

Physical Install

Tablets communicate to the Trimble base unit over Wi-Fi, so the devices do not physically interact. Tablet physical install consists of two parts:1) Mount the display to the dash using the provided

mount, adding a swivel if preferred.– Be sure the screws holding the cradle to the mount are

fully seated. Loose screw heads can create seating/charging issues.

– In this example, the RAM™ swivel mount is added to provide a clear view for the driver.

2) Connect the power cable and route it to the 2-pin Power connection point, either on the in-dash Power Assembly or the Trimble Base Unit Cable.– Be sure to secure all cables and connectors to avoid

damage or disconnect.

Notes on Power Connections

Most cradle cables come with the 2-pin power matching the PMG/PCG/TG field-installed cables.– If your cable does not have that plug, you can splice to the base unit

2-pin, red-to-red and black-to-black. Be sure to remove power before cutting the cable.

– You can also connect the Power and Ground directly to vehicle spares if preferred. Be sure to fuse the power side at 5 amps at the source, unless you are using the Trimble Fused Power Assembly.

Tab Active2™ and Tab Active3™ with ProClip™ Cradle Hardware Overview

Samsung Tab Active 3 and

Protective Sleeve

Part L-016-0537

ProClip Cradle

Locking = L-016-0532

Non-Locking = L-016-0531

Same for TA models 2 and 3

ProClip Power Cable

Included with Cradle

Not sold separately

Power Connection to

PMG Power Assembly or

PCG/TG 2-pin Power

Tab Active 2-3 with RAM™ CradleHardware Overview

Samsung Tab Active 3 and

Protective Sleeve

Part L-016-0537

RAM Cradle

Part H-053-0538

Same for TA models 2 and 3

RAM Power Cable

Included with Cradle

Not sold separately

Power Connection to

PMG Power Assembly or

PCG/TG 2-pin Power

Samsung A7 Lite™ ProClip Mount

A7 is encased in the cradle

with the USB charger

connected.

The power cable is included

in the kit and is not sold

separately.

ProClip with Key Lock

H-053-0537

ProClip no Key Lock

H-053-0536Quick-Release

2-Pin Power

Optional RAM Swivel Mount

The RAM swivel mount provides a flexible base to put the display in the driver’s view and reach. This is especially useful when the mount location is farther to the center or right of the dash. – H-050-0512 8” Arm

– H-050-0529 3” Arm

Tab A, Tab Active 2, A7 Lite Buttons

Volume

Power

Recents

Home

Back

Tab Active 3 Buttons

Press the Bixby/Power Button to boot.

A brief Bixby/Power + Volume Down = Screenshot.

An extended Bixby/Power + Volume Down = Power Down.

Press Active key to launch preset apps.

Recents Home Back

Volume

Bixby/Power

Active

Activation and Pairing

PMobile Android™ Permissions 1

Swipe

PMobile

AlwaysAllow

Allow Allow

PMobile Android Permissions 2

Allow all

the timeAllow Allow

OK Slide Right

Press BACK

PMobile Android Permissions 3

Allow Slide Right

Press BACK

Slide Right

Press BACK

Allow

Activation

Enter

Password

9238

Enter PMG/PCG Serial

Number (DSN)

Activation 2

Display may reboot to change

protocols, depending on base

unit type.

Re-enter the Password and

base unit serial number.

Re-enter the Password and

base unit serial number.

Activation 3The display will pair to the

base unit using a multi-step

security protocol. If an error

occurs at this point, reboot the

display and try again.

The display will ask if this is a

New Installation.

If the Vehicle and Base Unit

are new to the network,

answer Yes.

If the Vehicle or Base Unit are

already active in the network,

answer No.

Activation 4

For a New Install, enter the

Installer ID (optional) and

Vehicle ID then press Submit

For a Swap, enter the Installer

ID (optional) and Vehicle ID.

Leave Old DSN blank.

Then press Submit

Activation Complete

ELD Activation

When ELD is enabled for the first time, the display will reboot then

ask a series of Android permissions questions, similar to PMobile.

Allow all

the timeAllow Allow

ELD Activation 2

Allow only while

using the appAllow Allow

ELD Complete

Slide the bar right

and press Back

Install Complete