SCC8300 Series 2 - Tutt Bryant · Shanghai Sany Science & Technology Co., Ltd. 04 Jun 2013 (Rev 0.1) 3 / 14 ASME B30.5 SCC8300 SERIES 2 SCC8300.HC.702.AU ERECTION Note: Blocks,slings

SCC8300 Series 2 HC Configuration Capacities

Shanghai Sany Science & Technology Co., Ltd.Shanghai Sany Science & Technology Co., Ltd.04 Jun 2013 (Rev 0.1)

1 / 14

ASME B30.5ASME B30.5SCC8300 SERIES 2

SCC8300.HC.702.AU

HC CONFIGURATION CAPACITIESStandard Hook Work2825A Tubular Boom + Boom Point Extension 128.0 t Upper Counterweight57.0 t Carbody Counterweight360 Degree Rating

OPERATING CONDITIONS: Machine to operate in a level position on a fi rmuniformly supporting surface. Crane operator judgment must be used to allow for dynamic load effects of swinging, hoisting or lowering, travel, wind conditions, as well as adverse operating conditions and physical machine depreciation. Refer to SCC8300 Safety, Operation & Maintenance Manual for operating guidelines.

MACHINE TRAVEL:Machine to travel on a fi rm, level and uniformly supporting surface and boom within boom angle range shown in capacity chart. Refer to Maximum Allowable Travel Specifi cation chart.

OPERATING RADIUS: Operating radius is horizontal distance from axis of rotation to center of vertical hoist line or load block.

BOOM POINT ELEVATION: Boom point elevation is vertical d i s tance f rom ground leve l to centerline of boom point shaft.

BOOM ANGLE: Boom angle in degree is angle between horizontal and centerline of boom butt and inserts, and is an indication of operating radius. in all cases, operating radius shall govern capacity.

The capacities in the rating chart meet ASME B30.5 requirements, including SAE J987 and SAE J765.

Ratings in this chart are in tonnes and do not exceed the percentage of tipping specifi ed for this crane by ASME B30.5.

Capacities included in this chart are the maximum allowable and are based on machine standing level on firm supporting under ideal job conditions. And comply with Australian Standard AS 1418.5 - 2002.

Capacities are in tonnes and are not more than 75% of minimum tipping loads except the figures shaded areas which are based on strength of material or factors other than stability (tipping).

Weight of all load blocks, slings, buckets, hoist lines and other load carrying devices beneath the boom point sheaves, is considered part of the main boom load. Do not lift loads in excess of those shown on this chart. Lifting loads in excess of those shown or operation not in accordance with good operating practice can cause tipping, structural damage or catastrophic failure, Where no capacity is shown, operation is not intended or approved.

WARNING

This rating chart is invalid if the crane has been modifi ed or altered by use of other than genuine SANY parts as such modifications or alterations may affect its capacity or safe operation.


2 / 14


SCC8300.HC.702.AU

WIRE ROPEWIRE ROPE

Ratings shown in this chart only apply to cranes equipped with wire ropes that meet the diameter, minimum breaking strength and parts of line requirements as indicated. Consult the SCC8300 Transport, Assembly & Disassembly Manual for a complete listing of current wire rope specifi cations.

MAXIMUM WIND SPEED(measured at boom tip) 7 m/s 9 m/s 11 m/s 13 m/s 16 m/s

BOOM LENGTH

(m)PERCENT REDUCTION

20.0 ~ 47.0 0 % 0 % 0 % 0 % 0 %

50.0 ~ 65.0 0 % 0 % 0 % 10 % 20 %

68.0 ~ 92.0 0 % 0 % 10 % 20 % 30 %

WIND CONDITIONSWIND CONDITIONS

No account is taken of the wind force on the load. The user must consider this effect, which can be substantial for loads with large surface areas. In any wind it is strongly recommended that taglines be used to control the load.

Operation is permitted in steady winds or wind gusts provided capacities are reduced as indicated in the table below.

HOIST ROPE SPECIFICATION

HOIST ROPE SPECIFICATION MAIN HOIST AUXILIARY HOIST BOOM HOIST

DAMITER (mm) 28.0 28.0 26.0

CONSTRUCTION NOTOR HP 2160 - Resistant NOTOR HP 2160 - Resistant INTEGRAL 8 2160

MINIMUM BREAKING STRENGTH (kN) 785 785 694

LENGTH (m) 710 540 360


3 / 14


SCC8300.HC.702.AU

ERECTIONERECTION

Note: Blocks,slings and other load carrying devices must be on the ground during erection.

Erection " OVER-THE-SIDE " is with the boom 90° to the side frames.Erection " OVER-THE-END " is with the boom over the drive end or idler end of the sideframes.

Erection " OVER-THE-END BLOCKED " is with the boom over the idler end of the sideframe with the idler tumblers blocked (See SCC8300 Transport, Assembly & Disassembly Manual for blocking instructions).

MAXIMUM BOOM & JIB SELF-ERECTION DATA

BOOM + JIB( CONFIGURATION )

OVER-THE-SIDEOR

OVER-THE-ENDOVER-THE-END BLOCKED

BOOM LENGTH(m)

JIB LENGTH(m)

BOOM LENGTH(m)

JIB LENGTH(m)

2825A + BPE (HC) 86.0 N/A 92.0 N/A

No operation is permitted when wind conditions exceed 16 m/s. When this condition exists, the following applies.

WINDS UP TO 22 m/s : Lower the load block(s) and weight ball(s) to the ground. Orient the boom in-line with the sideframes / crawlers. Set the boom at a 70 degree boom angle.

WINDS 22 m/s AND ABOVE : Lower the boom to the ground.

Refer to the SCC8300 Safety, Operation & Maintenance Manual for additional information concerning operating the crane in wind.

LOAD HOISTING INFORMATION28.0 mm Diameter NOTOR HP 2160 - Resistant Wire Rope

Wire Rope Weight - 3.69 kg / m

MAXIMUM LIFTING CAPACITY(t)

MINIMUMPARTS OF LINE

30.0 2

15.0 1


4 / 14


SCC8300.HC.702.AU

BOOM COMPOSITION CHART2825A TUBULAR BOOM - HC CONFIGURATION

BOOMLENGTH

(m)

BOOM SECTIONS

10.0 m2825ABASE

3.0 m2825A

CENTER

6.0 m2825A

CENTER

12.0 m2825A

CENTER I

12.0 m2825A

CENTER II

7.0 m2825A

TIP

BOOMPOINT

EXTENSION

MIDPOINTSUSPEN

SION

20 1 1 0 0 0 1 1 023 1 0 1 0 0 1 1 026 1 1 1 0 0 1 1 029 1 0 0 0 1 1 1 032 1 1 0 0 1 1 1 035 1 0 1 0 1 1 1 038 1 1 1 0 1 1 1 041 1 0 0 0 2 1 1 044 1 1 0 2 0 1 1 047 1 0 1 0 2 1 1 050 1 1 1 2 0 1 1 053 1 0 0 1 2 1 1 056 1 1 0 2 1 1 1 059 1 0 1 1 2 1 1 062 1 1 1 2 1 1 1 065 1 0 0 2 2 1 1 068 1 1 0 2 2 1 1 071 1 0 1 2 2 1 1 074 1 1 1 2 2 1 1 077 1 0 0 3 2 1 1 080 1 1 2 2 2 1 1 083 1 0 1 3 2 1 1 086 1 1 1 3 2 1 1 189 1 0 2 3 2 1 1 192 1 1 2 3 2 1 1 1

Note:12.0 m 2825A CENTER I is fi tted with four 12.0 m pendant bars. And there is no connecting base at the end of the connector for the mid-point suspension cable.

12.0 m 2825A CENTER II is only fi tted with two 12.0 m pendant bars. And there is a connecting base at the end of the connector for the mid-point suspension cable.

Refer to the SCC8300 Transport, Assembly & Disassembly Manual for proper midpoint suspension selection and installation.


5 / 14


SCC8300.HC.702.AU

Explanation of SymbolsExplanation of Symbols

360°360 Degree Rating360 Degree Rating

Lifting CapacitiesLifting Capacities

Boom LengthBoom Length

Boom AngleBoom Angle

OperatingOperatingRadiusRadius

Boom Point Boom Point ElevationElevation

Crane CounterweightCrane Counterweight+

Carbody CounterweightCarbody Counterweight

Boom Point ExtensionBoom Point Extension+

No. 2825A Tubular Boom No. 2825A Tubular Boom

BPE+

2825A


6 / 14


° ° °m tm m tm m tm

128.0 t+

57.0 t 360°

BPE+

2825A

SCC8300.HC.702.AU

7.5 83.1 22.9 30.0 8 81.7 22.7 30.0 9 78.9 22.4 30.0 10 76.0 22.0 30.0 12 70.0 21.0 30.0 14 63.6 19.8 30.0 16 56.7 18.2 30.0 18 49.0 16.1 30.0

8 82.8 25.8 30.0 9 80.3 25.5 30.0 10 77.8 25.2 30.0 12 72.7 24.4 30.0 14 67.3 23.3 30.0 16 61.7 22.0 30.0 18 55.6 20.4 30.0 20 48.9 18.4 30.0 22 41.1 15.7 30.0

8 83.6 28.9 30.0 9 81.4 28.6 30.0

10 79.2 28.3 30.0 12 74.7 27.6 30.0 14 70.1 26.7 30.0 16 65.3 25.6 30.0 18 60.2 24.2 30.0 20 54.7 22.6 30.0 22 48.8 20.6 30.0 24 42.0 18.1 30.0

20.0 m 23.0 m 26.0 m

Note: Ratings shown in this chart must be meet the following list:1) Capacities are in tonnes, and are based on 75% of minimum tipping loads with machine standing level on fi rm supporting surface under ideal job conditions.2) Capacities shaded areas are based on strength of material or factors other than stability (tipping).3) Deduction from the lifting capacities must be made for mass of hook block, sling and other suspended gear.4) When the capacity of the hook block used is less than the lofting capacities, the hook block capacity is a maximum load.

KIND OF HOOK BLOCK HOOK BLOCK CAPACITY(t)

MASS (t)

15 t 15 1.0

50 t 50 2.4

100 t 100 3.2

150 t 150 3.8

300 t 300 6.2


7 / 14


° ° °m tm m tm m t m

128.0 t+

57.0 t 360°

BPE+

2825A

SCC8300.HC.702.AU

9 82.3 31.7 30.0 10 80.3 31.4 30.0 11 78.3 31.1 30.0 12 76.3 30.8 30.0 14 72.2 30.0 30.0 16 68.0 29.0 30.0 18 63.6 27.9 30.0 20 59.0 26.5 30.0 22 54.1 24.8 30.0 24 48.7 22.8 30.0 26 42.8 20.4 30.0

9 83.0 34.8 30.0 10 81.2 34.5 30.0 11 79.4 34.3 30.0 12 77.6 33.9 30.0 14 73.9 33.2 30.0 16 70.2 32.4 30.0 18 66.3 31.3 30.0 20 62.2 30.1 30.0 22 58.0 28.7 30.0 24 53.5 27.0 30.0 26 48.7 25.1 30.0 28 43.3 22.7 30.0 30 37.3 19.8 30.0

9 83.6 37.8 30.0 10 82.0 37.6 30.0 11 80.3 37.4 30.0 12 78.7 37.1 30.0 14 75.4 36.4 30.0 16 71.9 35.6 30.0 18 68.4 34.7 30.0 20 64.8 33.6 30.0 22 61.1 32.4 30.0 24 57.2 30.9 30.0 26 53.0 29.2 30.0 28 48.6 27.3 30.0 30 43.8 25.0 30.0 32 38.4 22.3 30.0

29.0 m 32.0 m 35.0 m


8 / 14



128.0 t+

57.0 t 360°

BPE+

2825A

SCC8300.HC.702.AU

9.5 83.3 40.8 30.0 10 82.6 40.7 30.0 11 81.1 40.4 30.0 12 79.6 40.2 30.0 14 76.5 39.6 30.0 16 73.4 38.9 30.0 18 70.2 38.0 30.0 20 67.0 37.0 30.0 22 63.6 35.9 30.0 24 60.1 34.6 30.0 26 56.5 33.2 30.0 28 52.7 31.5 30.0 30 48.6 29.5 30.0 32 44.2 27.3 30.0 34 39.3 24.6 30.0

10 83.1 43.7 30.0 11 81.7 43.5 30.0 12 80.3 43.3 30.0 14 77.5 42.7 30.0 16 74.7 42.1 30.0 18 71.7 41.3 30.0 20 68.8 40.4 30.0 22 65.7 39.4 30.0 24 62.6 38.2 30.0 26 59.3 36.9 30.0 28 55.9 35.4 30.0 30 52.3 33.7 30.0 32 48.6 31.8 30.0 34 44.5 29.6 30.0 36 40.1 27.0 30.0

10 83.6 46.8 30.0 11 82.3 46.6 30.0 12 81.0 46.3 30.0 14 78.4 45.8 30.0 16 75.7 45.2 30.0 18 73.0 44.5 30.0 20 70.3 43.7 30.0 22 67.5 42.7 30.0 24 64.6 41.7 30.0 26 61.6 40.5 30.0 28 58.6 39.1 30.0 30 55.4 37.6 30.0 32 52.0 35.9 30.0 34 48.5 34.0 30.0 36 44.8 31.8 30.0 38 40.7 29.3 30.0 40 36.2 26.4 26.1

38.0 m 41.0 m 44.0 m


9 / 14



128.0 t+

57.0 t 360°

BPE+

2825A

SCC8300.HC.702.AU

10 84.0 49.8 30.0 11 82.8 49.6 30.0 12 81.6 49.4 30.0 14 79.1 48.9 30.0 16 76.6 48.4 30.0 18 74.1 47.7 30.0 20 71.6 46.9 30.0 22 69.0 46.1 30.0 24 66.3 45.1 30.0 26 63.6 44.0 30.0 28 60.8 42.7 30.0 30 57.9 41.4 30.0 32 54.9 39.8 30.0 34 51.8 38.1 30.0 36 48.5 36.2 30.0 38 45.0 34.1 28.8 40 41.2 31.6 26.0 42 37.1 28.8 23.9

11 83.2 52.7 30.0 12 82.1 52.5 30.0 14 79.8 52.0 30.0 16 77.5 51.5 30.0 18 75.1 50.9 30.0 20 72.7 50.1 30.0 22 70.3 49.3 30.0 24 67.8 48.4 30.0 26 65.3 47.4 30.0 28 62.7 46.3 30.0 30 60.1 45.0 30.0 32 57.4 43.6 30.0 34 54.5 42.1 30.0 36 51.6 40.4 30.0 38 48.5 38.5 28.6 40 45.2 36.3 26.2 42 41.7 33.9 23.6 44 37.9 31.2 21.8

11 83.6 55.7 30.0 12 82.5 55.5 30.0 14 80.4 55.1 30.0 16 78.2 54.6 30.0 18 76.0 54.0 30.0 20 73.7 53.3 30.0 22 71.5 52.6 30.0 24 69.2 51.7 30.0 26 66.8 50.8 30.0 28 64.4 49.7 30.0 30 62.0 48.6 30.0 32 59.5 47.3 30.0 34 56.9 45.9 30.0 36 54.2 44.3 30.0 38 51.4 42.6 28.4 40 48.5 40.7 26.1 42 45.4 38.6 24.0 44 42.1 36.2 22.1 46 38.6 33.6 19.9 48 34.7 30.5 18.4

47.0 m 50.0 m 53.0 m


10 / 14



128.0 t+

57.0 t 360°

BPE+

2825A

SCC8300.HC.702.AU

11 83.9 58.7 30.0 12 82.9 58.6 30.0 14 80.9 58.2 30.0 16 78.8 57.7 30.0 18 76.7 57.1 30.0 20 74.6 56.5 30.0 22 72.5 55.8 30.0 24 70.3 55.0 30.0 26 68.1 54.1 30.0 28 65.9 53.1 30.0 30 63.6 52.0 30.0 32 61.3 50.8 30.0 34 58.9 49.5 30.0 36 56.4 48.1 30.0 38 53.9 46.5 28.2 40 51.2 44.8 25.9 42 48.5 42.9 23.8 44 45.6 40.8 21.9 46 42.5 38.5 20.2 48 39.2 35.9 18.1 50 35.6 33.0 16.7

12 83.3 61.6 30.0 14 81.3 61.2 30.0 16 79.4 60.8 30.0 18 77.4 60.3 30.0 20 75.4 59.7 30.0 22 73.4 59.0 30.0 24 71.4 58.2 30.0 26 69.3 57.4 30.0 28 67.2 56.5 30.0 30 65.1 55.5 30.0 32 62.9 54.3 30.0 34 60.6 53.1 30.0 36 58.4 51.8 30.0 38 56.0 50.4 28.0 40 53.6 48.8 25.7 42 51.1 47.1 23.6 44 48.4 45.2 21.7 46 45.7 43.1 20.0 48 42.8 40.8 18.4 50 39.7 38.3 16.5 52 36.4 35.4 15.3

12 83.6 64.7 30.0 14 81.8 64.3 30.0 16 79.9 63.9 30.0 18 78.0 63.4 30.0 20 76.1 62.8 30.0 22 74.2 62.2 30.0 24 72.3 61.4 30.0 26 70.3 60.7 30.0 28 68.4 59.8 30.0 30 66.4 58.8 30.0 32 64.3 57.8 30.0 34 62.2 56.6 30.0 36 60.1 55.4 30.0 38 57.9 54.1 27.7 40 55.6 52.6 25.4 42 53.3 51.0 23.3 44 50.9 49.3 21.4 46 48.4 47.4 19.7 48 45.8 45.4 18.1 50 43.1 43.1 16.6 52 40.2 40.6 14.9 54 37.1 37.8 13.7 56 33.7 34.7 12.6

56.0 m 59.0 m 62.0 m


11 / 14



128.0 t+

57.0 t 360°

BPE+

2825A

SCC8300.HC.702.AU

12 83.9 67.7 30.0 14 82.1 67.3 30.0 16 80.4 66.9 30.0 18 78.6 66.5 30.0 20 76.8 65.9 30.0 22 75.0 65.3 30.0 24 73.1 64.6 30.0 26 71.3 63.9 30.0 28 69.4 63.1 30.0 30 67.5 62.2 30.0 32 65.6 61.2 30.0 34 63.6 60.1 30.0 36 61.6 58.9 30.0 38 59.6 57.7 27.5 40 57.5 56.3 25.2 42 55.3 54.8 23.1 44 53.1 53.2 21.2 46 50.8 51.5 19.5 48 48.4 49.6 17.9 50 45.9 47.6 16.4 52 43.3 45.4 15.1 54 40.6 42.9 13.5 56 37.7 40.2 12.4 58 34.5 37.2 11.4

14 82.5 70.4 30.0 16 80.8 70.0 30.0 18 79.1 69.5 30.0 20 77.4 69.0 30.0 22 75.7 68.5 30.0 24 73.9 67.8 30.0 26 72.1 67.1 30.0 28 70.4 66.3 30.0 30 68.6 65.5 30.0 32 66.7 64.5 30.0 34 64.9 63.5 30.0 36 63.0 62.4 29.9 38 61.0 61.2 27.2 40 59.1 59.9 24.9 42 57.1 58.6 22.8 44 55.0 57.1 20.9 46 52.9 55.5 19.2 48 50.7 53.7 17.6 50 48.4 51.9 16.2 52 46.0 49.8 14.9 54 43.6 47.6 13.6 56 41.0 45.2 12.1 58 38.2 42.6 11.1 60 35.2 39.6 10.1

14 82.8 73.4 30.0 16 81.2 73.1 30.0 18 79.6 72.6 30.0 20 77.9 72.1 30.0 22 76.3 71.6 30.0 24 74.6 71.0 30.0 26 72.9 70.3 30.0 28 71.2 69.5 30.0 30 69.5 68.7 30.0 32 67.8 67.8 30.0 34 66.0 66.9 30.0 36 64.2 65.8 29.5 38 62.4 64.7 26.9 40 60.5 63.5 24.6 42 58.6 62.2 22.5 44 56.7 60.8 20.6 46 54.7 59.3 18.9 48 52.7 57.7 17.3 50 50.6 56.0 15.9 52 48.4 54.1 14.5 54 46.1 52.1 13.2 56 43.8 49.9 12.2 58 41.3 47.5 10.8 60 38.7 44.9 9.8 62 35.9 42.0 8.9

65.0 m 68.0 m 71.0 m


12 / 14



128.0 t+

57.0 t 360°

BPE+

2825A

SCC8300.HC.702.AU

14 83.1 76.5 30.0 16 81.5 76.1 30.0 18 80.0 75.7 30.0 20 78.4 75.2 30.0 22 76.8 74.7 30.0 24 75.2 74.1 30.0 26 73.6 73.5 30.0 28 72.0 72.7 30.0 30 70.4 72.0 30.0 32 68.7 71.1 30.0 34 67.0 70.2 30.0 36 65.3 69.2 29.1 38 63.6 68.2 26.7 40 61.9 67.0 24.3 42 60.1 65.8 22.2 44 58.2 64.5 20.3 46 56.4 63.1 18.6 48 54.5 61.6 17.0 50 52.5 59.9 15.6 52 50.5 58.2 14.3 54 48.4 56.3 13.1 56 46.2 54.3 11.9 58 44.0 52.2 10.9 60 41.6 49.8 9.9 62 39.1 47.2 8.7 64 36.5 44.4 7.8 66 33.7 41.3 7.0

14 83.4 79.5 30.0 16 81.9 79.2 30.0 18 80.4 78.8 30.0 20 78.9 78.3 30.0 22 77.4 77.8 30.0 24 75.8 77.2 30.0 26 74.3 76.6 30.0 28 72.7 75.9 30.0 30 71.2 75.2 30.0 32 69.6 74.4 30.0 34 68.0 73.5 30.0 36 66.4 72.6 28.5 38 64.7 71.6 26.2 40 63.1 70.5 24.1 42 61.4 69.3 22.0 44 59.6 68.1 20.1 46 57.9 66.7 18.4 48 56.1 65.3 16.8 50 54.2 63.8 15.4 52 52.3 62.2 14.0 54 50.4 60.4 12.8 56 48.4 58.6 11.7 58 46.3 56.6 10.6 60 44.1 54.4 9.7 62 41.9 52.1 8.8 64 39.5 49.6 7.6 66 37.0 46.8 6.8 68 34.4 43.8 6.1

14 83.6 82.5 30.0 16 82.2 82.2 30.0 18 80.7 81.8 30.0 20 79.3 81.4 30.0 22 77.8 80.9 30.0 24 76.4 80.4 30.0 26 74.9 79.8 30.0 28 73.4 79.1 30.0 30 71.9 78.4 30.0 32 70.4 77.6 30.0 34 68.9 76.8 30.0 36 67.3 75.9 27.9 38 65.7 74.9 25.6 40 64.1 73.9 23.5 42 62.5 72.8 21.6 44 60.9 71.6 19.8 46 59.2 70.4 18.1 48 57.5 69.0 16.5 50 55.8 67.6 15.1 52 54.0 66.0 13.7 54 52.2 64.4 12.5 56 50.3 62.7 11.4 58 48.4 60.8 10.3 60 46.4 58.8 9.4 62 44.3 56.7 8.5 64 42.2 54.4 7.6 66 39.9 51.9 6.5 68 37.5 49.2 5.8 70 35.0 46.2 5.1

74.0 m 77.0 m 80.0 m


13 / 14



128.0 t+

57.0 t 360°

BPE+

2825A

SCC8300.HC.702.AU

14 83.8 85.6 30.0 16 82.5 85.3 30.0 18 81.1 84.9 30.0 20 79.7 84.5 30.0 22 78.3 84.0 30.0 24 76.9 83.5 30.0 26 75.5 82.9 30.0 28 74.0 82.3 30.0 30 72.6 81.6 30.0 32 71.1 80.8 30.0 34 69.7 80.0 29.8 36 68.2 79.2 27.3 38 66.7 78.3 25.1 40 65.2 77.3 23.0 42 63.6 76.2 21.1 44 62.0 75.1 19.4 46 60.5 73.9 17.8 48 58.8 72.6 16.2 50 57.2 71.3 14.8 52 55.5 69.8 13.5 54 53.8 68.3 12.3 56 52.0 66.7 11.1 58 50.2 64.9 10.1 60 48.4 63.1 9.1 62 46.4 61.1 8.2 64 44.5 58.9 7.4 66 42.4 56.7 6.6 68 40.2 54.2 5.5 70 38.0 51.5 4.8 72 35.6 48.6 4.2 74 33.0 45.5 3.5

16 82.7 88.3 30.0 18 81.4 87.9 30.0 20 80.0 87.5 30.0 22 78.7 87.1 30.0 24 77.3 86.6 30.0 26 76.0 86.0 30.0 28 74.6 85.4 30.0 30 73.2 84.8 30.0 32 71.8 84.1 30.0 34 70.4 83.3 29.1 36 69.0 82.5 26.6 38 67.5 81.6 24.4 40 66.1 80.6 22.3 42 64.6 79.6 20.5 44 63.1 78.5 18.8 46 61.6 77.4 17.2 48 60.1 76.2 15.8 50 58.5 74.9 14.4 52 56.9 73.5 13.1 54 55.3 72.1 11.9 56 53.6 70.5 10.8 58 51.9 68.9 9.7 60 50.2 67.1 8.7 62 48.4 65.3 7.8 64 46.5 63.3 7.0 66 44.6 61.2 6.2 68 42.6 58.9 5.4 70 40.5 56.5 4.4 72 38.4 53.9 3.8 74 36.1 51.0 3.2 76 33.6 47.9 2.6

16 83.0 91.3 30.0 18 81.7 91.0 30.0 20 80.4 90.6 30.0 22 79.1 90.2 30.0 24 77.8 89.7 30.0 26 76.4 89.1 30.0 28 75.1 88.6 30.0 30 73.8 87.9 30.0 32 72.4 87.2 30.0 34 71.1 86.5 28.5 36 69.7 85.7 26.1 38 68.3 84.9 23.8 40 66.9 84.0 21.8 42 65.5 83.0 20.0 44 64.1 82.0 18.3 46 62.6 80.9 16.7 48 61.2 79.7 15.3 50 59.7 78.5 14.0 52 58.2 77.2 12.8 54 56.6 75.8 11.6 56 55.0 74.3 10.5 58 53.4 72.8 9.5 60 51.8 71.1 8.5 62 50.1 69.4 7.6 64 48.4 67.5 6.7 66 46.6 65.6 5.9 68 44.7 63.5 5.2 70 42.8 61.2 4.5 72 40.8 58.8 3.5 74 38.7 56.2 2.9 76 36.6 53.4 2.3 78 34.2 50.4 1.8

83.0 m 86.0 m 89.0 m


14 / 14


° °m tm m tm

128.0 t+

57.0 t 360°

BPE+

2825A

SCC8300.HC.702.AU

16 83.2 94.4 30.0 18 81.9 94.0 30.0 20 80.7 93.7 30.0 22 79.4 93.2 30.0 24 78.2 92.8 30.0 26 76.9 92.3 30.0 28 75.6 91.7 30.0 30 74.3 91.1 30.0 32 73.0 90.4 30.0 34 71.7 89.7 27.5 36 70.4 88.9 25.1 38 69.1 88.1 22.9 40 67.7 87.3 20.9 42 66.4 86.3 19.1 44 65.0 85.3 17.4 46 63.6 84.3 15.9 48 62.2 83.2 14.5 50 60.8 82.0 13.2 52 59.3 80.8 12.0 54 57.8 79.4 10.9

92.0 m

56 56.3 78.0 9.8 58 54.8 76.6 8.9 60 53.3 75.0 7.9 62 51.7 73.4 7.1 64 50.0 71.6 6.2

92.0 m

YEARSIN AUSTRALIA

1938-2018

Western RegionPerth (South Guildford), WAPh: 08 9230 0500Email: [email protected]

Karratha, WAPh: 08 9143 0089Email: [email protected]

Northern RegionDarwin (Berrimah), NTPh: 08 8924 1333Email: [email protected]

Eastern RegionBrisbane (Ormeau), QLDPh: 07 5540 8700Email: [email protected]

Sydney (Sydney Olympic Park), NSWPh: 02 9646 6000Email: [email protected]

Melbourne (Dandenong), VICPh: 03 9554 0300Email: [email protected]

Hunter RegionMuswellbrook, NSWPh: 02 6541 6444Email: [email protected]

Onlinewww.tuttbryant.com.au

Tutt Bryant Heavy Lift & Shift Locations

Singleton

Sydney

Brisbane

Melbourne

Perth

Karratha

South Guidlford

Darwin

Muswellbrook

Ormeau

Dandenong

Naval Base

Olympic Park

Berrimah

Documents

SCC8300 Series 2 - Tutt Bryant · Shanghai Sany Science & Technology Co., Ltd. 04 Jun 2013 (Rev 0.1) 3 / 14 ASME B30.5 SCC8300 SERIES 2 SCC8300.HC.702.AU ERECTION Note: Blocks,slings