SCRAMBLER 33 & 38 HYDRO DRIVE YZ SERIES 5 & 6 · PDF fileSCRAMBLER 33" & 38" HYDRO DRIVE YZ SERIES 5 & 6 ... 36 38" MOWER DECK ASSEMBLY ... per rear wheel & tire assembly 8 7042940

Parts Manual for

Revision 3,

SCRAMBLER 33" & 38" HYDRO DRIVE YZSERIES 5 & 6

COPYRIGHT © 2005

McDonough, GA, 30253 U.S.A.

TP 400-5007-3-HZ-N7/26/2005Manual No. 7006175

SNAPPER PRODUCTS, INC.ALL RIGHTS RESERVED.

MODELYZ16335BVEYZ16385BVEYZ18336BVEYZ18386BVE

Table Of Contents

TP 400-5007-3-HZ-NManual No. 7006175SCRAMBLER 33" & 38" HYDRO DRIVE YZ

SERIES 5 & 6 3

PAGE GROUP4 CASTER, FRONT WHEEL & TIRE ASSEMBLY6 WHEELS- REAR8 FRONT FRAME & COVER ASSEMBLY

10 REAR FRAME ASSEMBLY14 JOYSTICK & OPERATOR SEAT (Part 1)16 JOYSTICK & OPERATOR SEAT (Part 2)18 FENDER & TRANSAXLE ASSEMBLY22 BRAKE/CLUTCH LEVER ASSEMBLY24 ENGINE COMPONENTS26 CLUTCH ASSEMBLY28 DECK LIFT HANDLE ASSEMBLY30 33" MOWER DECK ASSEMBLY (Part 1)32 33" MOWER DECK ASSEMBLY (Part 2)34 33" MOWER DECK ASSEMBLY (Part 3)36 38" MOWER DECK ASSEMBLY (Part 1)38 38" MOWER DECK ASSEMBLY (Part 2)40 38" MOWER DECK ASSEMBLY (Part 3)42 33" SPINDLE ASSEMBLY44 38" SPINDLE ASSEMBLY46 DECALS (Part 1)48 DECALS (Part 2)50 ELECTRICAL COMPONENTS52 WIRING SCHEMATIC

CASTER, FRONT WHEEL & TIRE ASSEMBLY

TP 400-5007-3-HZ-NManual No. 7006175 SCRAMBLER 33" & 38" HYDRO DRIVE YZ

SERIES 5 & 64

CASTER, FRONT WHEEL & TIRE ASSEMBLY

Footnotes:


SERIES 5 & 6 5

Part No DescriptionItem Qty Note

1 7059090 2 ASSEMBLY, Front Wheel & Tire (Complete) (Includes Items 2 thru 5)

2 7035618 1 TIRE, 11 x 4.00-5, Smooth Tread per front wheel & tire assembly3 7039477 1 RIM, 5.00 Dia. x 3.00 per front wheel & tire assembly4 7076998 1 LUBE FITTING, 1/4-28 Thread Forming Was 29275, per front wheel &

tire assembly5 7012234 1 VALVE STEM, Air (Snap-in) per front wheel & tire assembly6 7012709 2 RING, 1” External Retaining7 7023556 4 BUSHING, Caster Was 466268 7013864 2 LUBE FITTING, Straight (press-fit for .187 dia. Hole)9 7041783 2 WELDMENT, Pivot Yoke, Caster

10 7090839 2 NUT, 7/16-14 Hex Center Lock, GR5 or B11 7035359 2 TUBE, 5/8 O.D. x 14 Ga x 4.5112 7035358 4 BEARING, Ball, 5/8 x 1-3/8”13 7091772 2 SCREW, 7/16-14 x 6” Hex Head Cap, GR5

WHEELS- REAR


SERIES 5 & 66

WHEELS- REAR

Footnotes:


SERIES 5 & 6 7


1 7058947 2 ASSEMBLY, Rear Tire & Rim (Includes items 2A, 3A & 7) used on 33” Deck Models-- 7058948 2 ASSEMBLY, Rear Tire & Rim (Includes items 2B, 3B & 7) used on 38” Deck Models2A 7046321 1 TIRE, 18 x 7.00-8, Multi-Trac per rear wheel & tire assembly2B 7046322 1 TIRE, 18 x 8.50-8, Multi-Trac per rear wheel & tire assembly3A 7039471 1 RIM, 18 x 7.00 Wheel w/25mm Hub I. D. per rear wheel & tire assembly3B 7039468 1 RIM, 18 x 8.50 w/25mm Hub per rear wheel & tire assembly4 7072028 2 WASHER, 1.56 x 1.054 x .047 Flat5 7091764 2 KLIPRING, 1” External (Waldes Truarc 5304-100)6 7011022 2 HUB CAP7 7012234 1 VALVE STEM, Air (Snap-in) per rear wheel & tire assembly8 7042940 2 KEY, Square M6 x 38mm

FRONT FRAME & COVER ASSEMBLY


SERIES 5 & 68

FRONT FRAME & COVER ASSEMBLY

Footnotes:


SERIES 5 & 6 9


1 7059380 1 WELDMENT, Front Frame Series #32 7075910 1 PLATE, Footrest Support3 7090595 6 BOLT, 5/16-18 x 3/4” Hex Flange Lock4 7091601 5 NUT, 5/16-18 Hex Flange Lock, GR5 Was 910705 7028260 2 FASTENER, “U” Type6 7090324 2 SCREW, 3/8-16 x 1” Hex Washer Self-tap7 7090517 2 WASHER, 3/8” FLAT (wide)8 7035375 2 SPACER, Front Frame Pivot9 7035374 1 PLATE, Front Frame Slip

10 7075841 1 FLOOR PAN, HOZ11 7075219 1 FOOTREST, HOZ12 7091890 4 WASHER, 1/4” Internal/External Lock13 7023341 2 KNOB (1/4-20 thread)14 7075885 1 MAT, Floor15 7041818 3 PAD, Floor Board Support16 7075993 1 DECAL, Warning, Read Manuals & Instructions see decal page17 7046426 1 DECAL, Deck Height see decal page18 7071916 1 DECAL, SNAPPER (14.56” long)

REAR FRAME ASSEMBLY


SERIES 5 & 610

REAR FRAME ASSEMBLY

Footnotes:


SERIES 5 & 6 11


1 7041782 1 WELDMENT, Rear Frame2 7035368 2 CUSHION, Seat Support3 7035369 2 SPRING, Seat Support4 7090999 2 SCREW, 1/4-20 x 5/8” Pan Head Self-Tap (Torx)5 7090731 2 BOLT, 5/16-18 x 1/2” Short Neck Carriage, GR5 Was 900046 7075630 1 HINGE, Seat7 7091601 2 NUT, 5/16-18 Hex Flange Lock, GR5 Was 910708 7033587 1 BUMPER, Rear9 7091506 4 SCREW, 5/16-18 x 1-1/2” Hex Washer Self-Tap

10 7091587 1 WASHER, .531 x 1.062 x .121 SAE Flat11 7090975 1 NUT, 1/2-13 Hex Center Lock, GR5 or B12 7041793 1 WELDMENT, Battery Bracket13 7013321 2 BUSHING, Tie Rod14 7090238 4 SCREW, 5/16-24 x 1” Hex Head Cap, GR515 7011791 4 RETAINER, 5/16” Bolt16 7091315 4 WASHER, .32 x .58 x .08 Split Lock17 7091297 4 NUT, 5/16-24 Hex, GR5 or B18 7011033 2 GROMMET19 7029464 1 ASSEMBLY, Brake/Clutch Cable20 7091730 1 BOLT, 1/2-13 Hex Shoulder21 7058728 1 WELDMENT, Idler Arm, Primary22 7058692 1 SPRING, Extension- 5” long23 7090122 3 WASHER, 3/8” SAE Flat24 7091585 2 NUT, 3/8-16 Hex Center Lock, GR5 or B25 7024344 1 PULLEY,Idler, V 3.30 HA26 7079832 1 BOLT, 3/8-16 x 4” Hex Head Cap, GR527 7034937 1 BRACKET, Hydro Idler28 7045168 1 SPRING, Extension, Hydro Idler29 7091553 1 SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR530 7039485 1 CABLE, Hydro Release Valve31 7091240 2 SCREW, #10-32 x 5/8” Hex Washer Head Machine32 7018574 1 IDLER, 4.12” Outside Diameter, Flat33 7090376 2 NUT, #10-32 Hex Nyloc34 7022886 1 SWITCH, Seat (NO/NC) Snap-In also shown on electronic

components page35 7075102 1 SLEEVE, Idler36 7034938 1 GUIDE, Belt37 7058691 1 COVER-Spring

REAR FRAME ASSEMBLY


SERIES 5 & 612

REAR FRAME ASSEMBLY

Footnotes:


SERIES 5 & 6 13


38 7091272 4 FASTENER, Ratchet39 7043858 2 BUSHING, Flange, .64 x .75 x .5

JOYSTICK & OPERATOR SEAT (Part 1)


SERIES 5 & 614


Footnotes:


SERIES 5 & 6 15


1 7035483 1 BRACKET, R.H. Tank Support2 7042637 1 WELDMENT, Bracket, Joystick3 7035533 1 PIVOT, Joystick Control4 7042636 1 WELDMENT, Handle, Joystick Control5 7091800 4 BOLT, 5/16-18 Shoulder, w/Nylon Patch6 7023656 1 LEVER, Shift Handle (grip)7 7090844 1 ROLL PIN, 3/16 x 3/4”8 7058531 1 ASSEMBLY, R.H. Fender9 7075612 1 BRACKET, R.H. Console

10 7035936 1 BOOT, Joystick, Rubber11 7046246 1 BRACKET, Joystick Boot12 7046494 1 STOP, Joystick13 7090999 4 SCREW, 1/4-20 x 5/8” Pan Head Self-Tap (Torx)14 7075811 1 DECAL, Ignition Switch see decal page15 7075760 1 DECAL, SNAPPER16 7034817 1 DECAL, SCRAMBLER17 7091593 1 PIN, 3/8 Self Locking Cotter18 7090188 3 WASHER, .34 x .69 x .08 Flat19 7044717 1 CYLINDER, Joystick Control20 7044763 1 WELDMENT, U-Bracket21 7091020 2 PUSHNUT, 1/4”22 7044702 1 PIN, Joystick23 7091511 1 NUT, 5/16-18 Hex, GR5 or B24 7091315 1 WASHER, .32 x .58 x .08 Split Lock25 7014664 1 BOLT, 5/16-18 x .530” Shoulder26 7075617 1 ARM REST, HOZ27 7091908 2 SCREW, 5/16-18 x 1-3/4” Hex Head Cap, GR528 7091298 2 NUT, 5/16-18 Hex Nyloc29 7075610 1 FENDER, R.H. Lower30 7091542 4 SCREW, 5/16-18 x 1/2” Pan Head Self-Tap (Torx)31 7026343 1 SWITCH, Ignition(After-fire Solenoid) also shown on electronic

components page32 7091819 7 SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap Was 9036233 7058513 1 WELDMENT, Fender Support34 7090361 2 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap



SERIES 5 & 616


Footnotes:


SERIES 5 & 6 17


13 7090999 6 SCREW, 1/4-20 x 5/8” Pan Head Self-Tap (Torx)15 7075760 1 DECAL, SNAPPER18 7090188 2 WASHER, .34 x .69 x .08 Flat26 7075617 1 ARM REST, HOZ27 7091908 2 SCREW, 5/16-18 x 1-3/4” Hex Head Cap, GR528 7091298 2 NUT, 5/16-18 Hex Nyloc30 7091542 4 SCREW, 5/16-18 x 1/2” Pan Head Self-Tap (Torx)32 7091819 3 SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap Was 9036234 7090361 2 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap35 7035481 1 BRACKET, L.H. Tank Support36 7075629 1 BRACKET, Brake/Clutch Detent37 7075609 1 FENDER, L.H. Lower38 7023355 1 SWITCH, Park Brake (NC/NO) also shown on electronic

components page39 7090913 2 SCREW, #10-24 x 1/2" Hex Washer Self-Tap (Torx) (Torx)

40A 7075611 1 BRACKET, L.H. Console series 540B 7038601 1 BRACKET, L.H. Console series 641 7075884 1 SWITCH, PTO E.C. (Delta Part No. 6201-219) also shown on electronic

components page42A 7072517 1 CONTROL, Throttle/Choke, Dual Lever series 542B 7024642 1 CONTROL, Throttle series 6 (not shown)43 7058511 1 WELDMENT, Fuel Tank Support44 7058530 1 ASSEMBLY, Fuel Tank/Left Hand Fender includes fuel cap (75748),

grommet (12337), fitting (74835) & tube (75708)

45 7075748 1 GAS CAP w/Screw Vent46 7074835 1 FITTING, Dapco Dapco part number #1149247 7012337 1 GROMMET48 7075708 1 DIP TUBE49 7071683 1 DECAL, Hydro Release see decal page50 7075812 1 DECAL, Park Brake see decal page51 7075810 1 DECAL, Operating Instructions see decal page52 7044897 1 SEAT, Milsco High Back53 7046561 1 TETHER, Seat54 7075628 1 HEAT SHIELD, Engine55 7090858 4 SCREW, 5/16-18 x 1/2” Hex Washer Self-Tap56 7023655 1 LEVER, Throttle Control series 657 7071921 1 RIVET, Plastic Snap series 6

FENDER & TRANSAXLE ASSEMBLY


SERIES 5 & 618


Footnotes:


SERIES 5 & 6 19


1 7029128 1 TRANSAXLE, Hydro Eaton Model X778-0052 7029129 1 TRANSAXLE, Hydro w/o Manifold R.H. Eaton Model X778-0113 7015894 2 KEY, #605 Woodruff4 7091122 8 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was 905395 7035337 2 FAN, 6” O.D., 10 Blade6 7035336 2 PULLEY, Hydro Input7 7091771 2 RING, RR3100-66 External Retaining8 7041823 1 V-BELT, HA Sect. 42.00” effective length Hydro Drive9 7034915 2 BRACKET, Support, Fender

10 7034916 1 BRACKET, Support, Hydro11 7091819 4 SCREW, 1/4-20 x 5/8” Hex Washer Self-Tap Was 9036212 7034909 1 FENDER, Rear Frame, Left Hand13 7034908 1 FENDER, Rear Frame, Right Hand14 7034917 1 BRACKET, Deck Support, Left Rear15 7035424 1 BRACKET, Deck Support, Right Rear17 7091541 26 SCREW, 5/16-18 x 3/4” Hex Washer Self-Tap Was 9036818 7090324 8 SCREW, 3/8-16 x 1” Hex Washer Self-tap19 7034922 2 BRACKET, Control Cable, Hydro20 7029147 4 ROD END, #10-32 w/Stud21 7091801 4 NUT, #10-32 Hex Center Lock22 7029170 1 CABLE, L.H. Hydraulic Control (45.5” long)23 7029169 1 CABLE, R.H. Hydraulic Control (35.5” long)24 7039484 1 BRACKET, Cable, Hydro Release Valve25 7090361 2 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap26 7039483 2 BRACKET, Actuator, Hydro Release Valve27 7012114 2 BUSHING, Differential Link, Powdered Metal28 7091841 2 SCREW, 5/16-18 x 1” Hex Washer Self-Tap, GR529 7034913 2 ARM, Directional Control30 7091165 4 BOLT, 1/4-28 x 5/8” w/Nyloc Patch, GR831 7090746 4 WASHER, 1/4” Belleville32 7034914 2 ARM, Brake33 7090122 6 WASHER, 3/8" Flat Was 9151434 7029284 1 ROD, Brake, R.H.35 7029142 1 ROD, Brake, L.H.36 7091594 2 COTTER-PIN, 1/16" x 1.42" Self-Locking Was 2487437 7024586 2 SWIVEL, Brake Link- PM



SERIES 5 & 620


Footnotes:


SERIES 5 & 6 21


38 7074511 2 SPRING, Brake Compression39 7091299 2 NUT, 3/8-16 Hex Nyloc40 7039485 1 CABLE, Hydro Release Valve41 7044767 1 DECAL, Hydro Reservoir see decal page42 7090011 2 WASHER, #10, Internal Tooth Lock43 7090013 3 NUT, #10-32, Hex

BRAKE/CLUTCH LEVER ASSEMBLY


SERIES 5 & 622

BRAKE/CLUTCH LEVER ASSEMBLY

Footnotes:


SERIES 5 & 6 23


1 7075774 1 GRIP, 5/16 x 2-1/2” Vinyl color: red (replaces 29383)2 7035945 1 GRIP, Brake/Clutch Handle3 7075527 1 ROD, Park Brake 36” arc radius (replaces 35479 &

58542)4 7035946 1 SPRING, Clutch/Brake Release5 7035485 1 ARM, Brake/Clutch Lever6 7035484 1 PIVOT, Brake/Clutch Lever7 7091084 1 SCREW, 1/4-20 x 3/8” Hex Washer Self-Tap Was 912938 7075528 1 TUBE, Clutch/Brake Lever 35.99” arc radius (replaces

58541)9 7010694 1 BUSHING, Nylon

10 7029207 1 ROD, Clutch/Brake11 7052431 2 ASSEMBLY, Foot Shaft Pivot weldment with grease fitting,

1386412 7090841 3 PIN, 3/16 x 1-1/2” Roll13 7029208 1 ARM, Brake/Clutch14 7042614 1 WELDMENT, Brake/Clutch Arm15 7091601 4 NUT, 5/16-18 Hex Flange Lock, GR5 Was 9107016 7091000 4 SCREW, 5/16-18 x 7/8” Pan Head Self-Tap (Torx)

ENGINE COMPONENTS


SERIES 5 & 624

ENGINE COMPONENTS

Footnotes:


SERIES 5 & 6 25


1 -- 1 ENGINE, 18 HP Briggs Intek Model 31H777-0115-E1 (series 5)

-- -- 1 ENGINE, 18 HP Briggs Intek Model 31H777-0117-E1 (series 6)

2 7010210 1 KEY, 1/4” Square x 2”3 7015352 2 GASKET, Exhaust4 7027972 1 ASSEMBLY, Oil Valve5 7035362 1 GUIDE, Engine Belt6 7036389 1 PLATE, Engine7 7041822 1 PULLEY, Engine series 5 (bottom pulley 4.25

O.D.)-- 7040706 1 PULLEY, Engine series 6 (bottom pulley 4.75

O.D.)8 7090324 4 SCREW, 3/8-16 x 1” Hex Washer Self-tap engine mounting bolts9 7091301 1 WASHER, 7/16 Split Lock

10 7091763 1 SCREW, 7/16-20 x 1-1/2” Hex Head Cap, GR511 7091807 1 WASHER, .468 x 1.38 x .25 Flat (special)12 7029900 4 HOSE CLAMP, .490 x .31 or 1222213 7024161 2 BOLT, 5/16-18 x 4” Shoulder14 7024566 1 SCREW LOCK15 7041537 1 DEFLECTOR, Muffler16 7071756 1 ADAPTER, Muffler Briggs part no. 69576617 7074826 1 MUFFLER, 14.5HP B&S Engine Nelson part no. 25482D18 7091581 3 SCREW, #8-18 x 1/2” Hex Head Sheet Metal19 7044824 1 HEAT SHIELD, Muffler- 17HP B&S Intek series 5-- 7041340 1 HEAT SHIELD, Muffler- B&S series 620 7029982 1 HOSE, Fuel, 1/4 I.D. x 14” long21 7016325 1 VALVE, Fuel22 7012638 1 HOSE, Fuel, 12-1/2” long Was 12912

23A 7072517 1 CONTROL, Throttle/Choke, Dual Lever series 523B 7024642 1 CONTROL, Throttle series 624 7091122 3 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap Was 9053925 7090606 1 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR5 Was 9151026 7015861 1 HARNESS CLIP (vinyl covered)27 7071760 1 HEAT SHIELD28 7023655 1 LEVER, Throttle Control series 629 7071921 1 RIVET, Plastic Snap series 630 7091240 2 SCREW, #10-32 x 5/8” Hex Washer Head Machine series 631 7090376 2 NUT, #10-32 Hex Nyloc series 6

CLUTCH ASSEMBLY


SERIES 5 & 626

CLUTCH ASSEMBLY

Footnotes:


SERIES 5 & 6 27


1 7091735 1 BOLT, 7/16-20 x 8” Hex Head, GR52 7029138 2 WASHER, .468 I.D. x 1.50 O.D. x .188 Flat3 7029136 2 BEARING, 6305 w/Snap Ring4 7091601 6 NUT, 5/16-18 Hex Flange Lock, GR5 Was 910705 7029117 1 V-BELT, 5L Sect. Cog, 50.170” effective length Primary Drive (Dayco #46-0364)6 7029107 1 PULLEY, Jackshaft7 7091829 2 SCREW, 1/4-20 x 1/2” Set w/Patch8 7063269 1 SUPPORT, Jackshaft- TG 20009 7091508 6 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR5

10 7029135 1 JACKSHAFT11 7013250 2 KEY 1/4” Square x 1” qty. 1 on 38” units12 7074573 1 BRACKET, Anti-Rotation, Ogura used on 33” units13 7029232 1 CLUTCH, Electric Ogura MA-GT-SN11S (33” units)-- 7074022 1 CLUTCH/BRAKE, Electric (Warner) (38” units)14 7091301 1 WASHER, 7/16” Split Lock15 7090460 1 NUT, 7/16-20 Hex, GR5 or B16 7012652 1 WIRE CLIP 7/16”, Vinyl Covered

17A 7029137 1 SPACER, Jackshaft17B 7075110 1 SPACER, Clutch (Ogura)

DECK LIFT HANDLE ASSEMBLY


SERIES 5 & 628

DECK LIFT HANDLE ASSEMBLY

Footnotes:


SERIES 5 & 6 29


1 7041924 1 HANDLE, Deck Lift2 7041925 1 BRACKET, Pivot Support3 7058090 1 WELDMENT, Deck Lift Handle4 7029040 1 WASHER - Slipper5 7046489 1 SPRING, Torsion6 7090072 2 SCREW, 1/4-20 x 5/8” Hex Head Cap, GR57 7091584 3 NUT, 1/4-20 Hex Flange Lock Was 905838 7035489 1 BAR, Deck Lift9 7090122 3 WASHER, 3/8” SAE Flat

10 7091503 2 HAIR PIN, 3/32 x 1-1/2”11 7013996 1 PIN, 3/8 x 2” Clevis12 7058077 1 DETENT, Lift Handle13 7091318 1 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR514 7091601 1 NUT, 5/16-18 Hex Flange Lock, GR5 Was 9107015 7046457 1 DECAL, Deck Position16 7091887 1 PIN.38 x .5 Large Head Clevis17 7046491 1 PIN, 3/8 x 1-5/8” Clevis18 7046490 1 SPACER, Deck Lift19 7091597 1 PIN, 3/32 x 3/4” Cotter20 7091530 1 BOLT, 1/4-20 x 3/4 Short Neck Carriage, GR521 7074768 2 GRIP, Deck Lift

33" MOWER DECK ASSEMBLY (Part 1)


SERIES 5 & 630


Footnotes:


SERIES 5 & 6 31


1 7061956 1 * DECK, 33” Replacement2 7034866 2 BRACKET, 33 Deck Lift, Slotted3 7034867 2 BRACKET, 33 Deck Lift4 7033570 1 BRACKET, Anti-Scalp, Front, Adjustment5 7033571 2 BRACKET, Anti-Scalp, Side, Adjustment6 7036579 1 WEIGHT BAR, 33 Rear, HOZ7 7091640 2 BOLT, 3/8-16 x 1” Square Neck Carriage, GR 5 replaces 907478 7074467 1 NUT, 3/4-16 Hex Jam, GR 89 7090595 8 BOLT, 5/16-18 x 3/4” Hex Flange Lock

10 7091601 14 NUT, 5/16-18 Hex Flange Lock Was 9058511 7090700 1 BOLT, 5/16-18 Hex Flange Lock, GR512 7028620 1 SPACER, .340 I.D. x .63 O.D. x .310” thick13 7091575 1 NUT, 5/16-18 Hex Center Lock, GR B Was 9106714 7090731 6 BOLT, 5/16-18 x 1/2” Short Neck Carriage, GR5 Was 9000415 7038018 1 BRACE, Spindle16 7091588 7 BOLT, 3/8-16 x 3/4” Hex Flange Lock, GR5 Was 90612 or 9158817 7091619 4 NUT, 3/8-16 Hex Flange Lock Was 9061318 7034168 1 BLADE, 33 High Lift19 7090491 2 SCREW, 1/2-20 x 1-1/4 Hex Head Cap, GR5 replaces 9039220 7090509 2 WASHER, 1/2” Internal Tooth Lock21 7091939 2 NUT, 1/2-20 Hex GR5 or B replaces 9055922 7052917 1 ASSEMBLY, Spindle23 7012670 1 TOLERANCE RING, 2”24 7010740 2 RING, 2” External Retaining25 7042587 1 WELDMENT, Idler Arm, 3326 7014407 1 WASHER, Spindle27 7026558 1 PULLEY, 33” Spindle28 7032028 2 WASHER, .781 x 1.5 x .132 Flat29 7091585 5 NUT, 3/8-16 Hex Center Lock Was 90546



SERIES 5 & 632


Footnotes:


SERIES 5 & 6 33


28 7032028 2 WASHER, .781 x 1.5 x .132 Flat29 7091585 1 NUT, 3/8-16 Hex Center Lock Was 9054630 7042586 1 WELDMENT, Lift Arm, Front31 7010935 4 WASHER, 3/4” Flat32 7015447 1 ECCENTRIC, Leveling33 7090390 1 WASHER, 3/8” Internal Tooth Lock34 7034815 1 LIFT ARM, Front35 7090163 1 SCREW, 3/8-24 x 1-1/4” Hex Head Cap w/Nylon Patch, GR536 7042585 1 WELDMENT, Lift Arm, Rear37 7035495 1 ROD, Cutter Deck Timing38 7024586 1 SWIVEL, Brake Link- PM39 7021815 1 SPACER, .391 I.D. x .531 long40 7090122 1 WASHER, 3/8” SAE Flat41 7091310 1 HAIR PIN, #13 Was 1623142 7022717 1 ROD, Deck Support43 7017847 1 RING, .438 External Retaining



SERIES 5 & 634


Footnotes:


SERIES 5 & 6 35


44 7091532 3 SCREW, 3/8-24 x 3-3/4 Hex Head Cap, GR545 7015272 3 SPACER, 3” long46 7019190 3 WHEEL, Gage47 7052555 1 ASSEMBLY, Discharge Chute includes items 48 thru 5348 7016341 1 SPRING, Hinge49 7026233 1 CHUTE, Discharge, 28”/33”50 7026234 1 ROD, Chute51 7026483 1 PALNUT WASHER (for .25 dia. rod)52 7013010 2 DECAL, Danger, Cut Finger (CPSC) replaces 2683153 7033780 1 HINGE, Plastic Side Chute54 7091811 3 BOLT, 5/16-18 x 5/8” Hex Flange Lock, GR555 7091601 3 NUT, 5/16-18 Hex Flange Lock, GR556 7075707 1 IDLER, Flat (4.00 O.D.) replaces 2771757 7090122 4 WASHER, 3/8" Flat Was 9151458 7091585 2 NUT, 3/8-16 Hex Center Lock, GR5 or B59 7035969 1 SPRING, Extension 1.03 Dia. X 6.8” long60 7035389 1 BELT, HA Section, 33 DECK (55.2” effective length)61 7022991 1 DECAL, 33 Hi-Vac62 7091503 3 HAIR PIN, 3/32 x 1-1/2”63 7028728 2 ADJUSTER, Chain (5/16-18 thread)64 7028200 2 SWIVEL, Adjustment65 7091508 1 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR566 7090188 1 WASHER, 11/32” Flat Was 9129667 7091537 1 WING NUT, 5/16-18 Was 9049268 7091528 1 WASHER, .375 x .875 x .083 Flat69 7090289 3 NUT, 3/8-24 Hex Center Lock replaces 9160070 7046720 1 DECAL, Chute/Deflector



SERIES 5 & 636


Footnotes:


SERIES 5 & 6 37


1 7061957 1 * DECK, 38” Replacement2 7063198 2 ASSEMBLY, Spindle- 38 Deck Was 59377 or 545133 7029213 2 PULLEY, 4.5 O.D., A/B Groove4 7058440 1 ASSEMBLY, Idler Arm, 38 Deck includes items 5 thru 75 7058440 1 WELDMENT, Idler Arm Was 584396 7011016 2 BUSHING, 1/2” Nylon7 7013864 1 LUBE FITTING, Straight (press-fit for .187 dia. Hole)8 7033756 1 BRACKET, Gage Wheel9 7033891 1 BRACKET, Left Hand Wheel

10 7034861 1 BRACKET, 38 Deck Lift, Left Front11 7034863 1 BRACKET, 38 Deck Lift, Right Front12 7090595 15 BOLT, 5/16-18 x 3/4” Hex Flange Lock replaces 9063613 7035566 1 BRACKET, L.H., Rear Lift Arm14 7091575 1 NUT, 5/16-18 Hex Center Lock, GR5 or B15 7091619 2 NUT, 3/8-16 Hex Flange Lock Was 9061316 7090658 2 NUT, 5/8-18 Hex Jam or 9100617 7035494 1 BRACKET, Gage Wheel18 7042964 1 STUD, Idler (5/16-24 thread)19 7044648 1 WELDMENT, Stationary Idler20 7091601 19 NUT, 5/16-18 Hex Flange Lock Was 9058521 7090799 13 BOLT, 5/16-18 x 5/8” Short Neck Carriage, GR5 Was 9102622 7092062 1 NUT, 5/16-24 Hex Lock, GR C Was 1120123 7091547 3 BOLT, 3/8-16 x 3/4” Short Neck Carriage Was 90850 or 9154724 7091587 3 WASHER, .531 x 1.062 x .121 SAE Flat25 7091597 1 PIN, 3/32 x 3/4” Cotter replaces 9108226 7091303 1 BOLT, 5/16-18 x 1” Short Neck Carriage, GR5 replaces 9095827 7028620 1 SPACER, .340 I.D. x .63 O.D. x .310” thick28 7091528 1 WASHER, .375 x .875 x .083 Flat29 7016314 1 WASHER, 5/16 x1-1/4” x .09 Flat



SERIES 5 & 638


Footnotes:


SERIES 5 & 6 39


30 7015447 1 ECCENTRIC, Leveling31 7034815 1 LIFT ARM, Front32 7090390 1 WASHER, 3/8” Internal Tooth Lock33 7090163 1 SCREW, 3/8-24 x 1-1/4” Hex Head Cap w/Nylon Patch, GR534 7042586 1 WELDMENT, Lift Arm, Front35 7010935 4 WASHER, 3/4” Flat36 7035495 1 ROD, Cutter Deck Timing (3/8-16 thread)37 7042585 1 WELDMENT, Lift Arm, Rear38 7024586 1 SWIVEL, Brake Link- PM39 7091310 1 HAIR PIN, #13 Was 1623140 7091585 1 NUT, 3/8-16 Hex Center Lock Was 9054641 7032028 2 WASHER, .781 x 1.5 x .132 Flat42 7021815 1 SPACER, .391 I.D. x .531 long43 7091528 1 WASHER, .375 x .875 x .083 Flat



SERIES 5 & 640


Footnotes:


SERIES 5 & 6 41


14 7091575 1 NUT, 5/16-18 Hex Center Lock, GR5 or B15 7091619 1 NUT, 3/8-16 Hex Flange Lock Was 9061344 7026122 3 WHEEL, 4 x 1-1/2” Offset45 7091526 3 BOLT, 3/8-24 x .62 Shoulder46 7013010 1 DECAL, Danger, Cut Finger (CPSC) replaces 2683147 7022717 1 ROD, Deck Support48 7017847 1 RING, .438 External Retaining49 7029308 1 V-BELT, HA Section 89.8” Effective Length50 7090188 1 WASHER, .34 x .69 x .08 Flat replaces 9129651 7028728 2 ADJUSTER, Chain (5/16-18 thread)52 7028200 2 SWIVEL, Adjustment53 7091503 3 HAIR PIN, 3/32 x 1-1/2”54 7090122 13 WASHER, 3/8” SAE Flat replaces 9151455 7026154 1 DECAL, 38 Inch56 7046720 1 DECAL, Chute/Deflector57 7035969 1 SPRING, Extension 1.03 Dia. X 6.8” long58 7024452 1 IDLER, 3-1/4” I.D. x 1-1/4” Flat59 7072319 1 PULLEY, 3-1/4 Dia. Flat Idler60 7012063 1 WASHER, Cone61 7029425 1 CHUTE, Discharge, 38” Deck62 7035502 1 ROD, Pivot, Side Discharge, 3863 7091508 1 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR564 7035503 1 ROD, Mounting, Side Discharge 3/8-16 thread65 7035813 1 SPRING, Torsion-Side Discharge-38 Deck66 7036543 1 TEENUT, 5/16-18 Thread67 7091553 2 SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR5 replaces 9156068 7090289 3 NUT, 3/8-24 Hex Center Lock69 7091585 2 NUT, 3/8-16 Hex Center Lock, GR5 or B70 7091833 1 SCREW 5/16-18 x 5/8” Cross Recessed Pan Head Was 91918

33" SPINDLE ASSEMBLY


SERIES 5 & 642


Footnotes:


SERIES 5 & 6 43


-- 7052917 1 ASSEMBLY, Spindle includes items 1 thru 101 7047962 1 WELDMENT, Spindle Housing2 7024687 1 SHAFT, Spindle (7.54” long)3 7014407 1 WASHER, Spindle4 7013313 2 BALL BEARING, 3/4” I.D.5 7037751 1 HOLDER, Blade6 7012491 2 RING, 1-3/4” External Retaining Ring7 7010817 1 FITTING, Lube, Press-In (for .187 dia. Hole)8 7090356 1 NUT, 5/8-18 Hex Center Lock Jam, GR5 or B9 7090392 2 SCREW, 1/2-20 x 1” Hex Head Cap

10 7091939 2 NUT, 1/2-20 Hex GR5 or B replaces 90559



SERIES 5 & 644


Footnotes:


SERIES 5 & 6 45


-- 7063198 2 ASSEMBLY, Spindle- 38 Deck Was 59377 (Includes 2 thru 9)1 7010817 1 FITTING, Lube, Press-In (for .187 dia. Hole)2 7012491 2 RING, 1-3/4” External Retaining Ring3 7013313 2 BALL BEARING, 3/4” I.D.4 7059378 1 WELDMENT, 38 Spindle Housing5 7072537 1 SHAFT, Spindle (7.155” long)6 7072109 1 WASHER, Spindle Blade7 7024467 2 WASHER, Bellville 9/16 x 1-3/4”8 7091633 1 NUT, 9/16-18 Hex, GR B9 7042998 1 BLADE, 19.64- 38 Deck

10 7072440 1 SPACER, Pulley

DECALS (Part 1)


SERIES 5 & 646

DECALS (Part 1)

Footnotes:


SERIES 5 & 6 47


1 7075760 2 DECAL, SNAPPER2 7034817 1 DECAL, SCRAMBLER3 7075812 1 DECAL, Park Brake4 7046426 1 DECAL, Deck Height5 7075811 1 DECAL, Ignition Switch6 7075594 1 DECAL, Engine, 16 HP OHV B&S Simplicity part no. 17230707 7044767 1 DECAL, Hydro Reservoir8 7046457 1 DECAL, Deck Position9 7022991 1 DECAL, 33 Hi-Vac

10 7026154 1 DECAL, 38 Inch

DECALS (Part 2)


SERIES 5 & 648

DECALS (Part 2)

Footnotes:


SERIES 5 & 6 49


11 7075993 1 DECAL, Warning, Read Manuals & Instructions12 7075810 1 DECAL, Operating Instructions14 7046720 1 DECAL, Chute/Deflector15 7013010 1 DECAL, Danger, Cut Finger13 7071683 1 DECAL, Hydro Release17 7075635 1 DECAL, Service Parts, HOZ Domestic18 7029113 1 DECAL, Caution, Fuel (English)16 7073335 1 DECAL OPEI Ride-On

ELECTRICAL COMPONENTS


SERIES 5 & 650

ELECTRICAL COMPONENTS

Footnotes:


SERIES 5 & 6 51


1 7075497 1 WIRING HARNESS, 18 HP Briggs2 7090977 2 NUT, 1/4-20 Hex Jam, GR5 or B3 7090411 2 SCREW, #10-24 x 1/2” Hex Head Cap4 7091584 3 NUT, 1/4-20 Hex Flange Lock5 7016835 1 WIRE, Positive, 13” long6 7042956 1 WIRE, Negative, 14” long7 7071694 2 COVER, Battery Cable8 7090053 3 WASHER, 1/4” Internal Tooth Lock Was 913149 7022886 1 SWITCH, Seat (NO/NC) Snap-In

10 7075884 1 SWITCH, PTO E.C. Delta part no. 6201-21911 7023355 1 SWITCH, Park Brake (NC/NO)12 7090913 3 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Torx)13 7029130 1 BATTERY, 12V, 3 Amp, 190 Cold Cranking Amp includes drain tube14 7026343 1 SWITCH, Ignition (After-fire Solenoid)15 7029714 1 SPACER, .65 x .88 x .10 - YZ16 7023506 1 BEZEL17 7075622 1 SOLENOID - Super Trombetta- 2 Terminal18 7090071 2 SCREW, 1/4-20 x 1/2” Hex Head Cap, GR519 7012688 2 NUT, #10-24 Hex Twin “Whiz” Lock20 7035661 1 SPACER, PTO Switch not shown

WIRING SCHEMATIC


SERIES 5 & 652

WIRING SCHEMATIC

Footnotes:


SERIES 5 & 6 53


-- -- 1 Wiring schematic includes harness # 75497

Parts Manual for

SCRAMBLER 33" & 38" HYDRO DRIVE YZSERIES 5 & 6

IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE

RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.

Revision 3,

COPYRIGHT © 2005

TP 400-5007-3-HZ-N7/26/2005Manual No. 7006175

SNAPPER PRODUCTS, INC.ALL RIGHTS RESERVED.

McDonough, GA, 30253 U.S.A.

Documents

SCRAMBLER 33 & 38 HYDRO DRIVE YZ SERIES 5 & 6 · PDF fileSCRAMBLER 33" & 38" HYDRO DRIVE YZ SERIES 5 & 6 ... 36 38" MOWER DECK ASSEMBLY ... per rear wheel & tire assembly 8 7042940