ScreenLogic™ Wireless Connection Kit - pentair.com · Personality board COM PORT Pin configuration Note: Install the ScreenLogic outdoor wireless transceiver within 10 feet from

ScreenLogic Wireless Connection Kit Installation Guide

Installation Guide

ScreenLogic™Wireless Connection Kit

pool/spa control system

ScreenLogic Wireless Connection Kit Installation GuideP/N 520663 - Rev B


Technical Support

Contact Technical Support at:

Sanford, North Carolina (8 A.M. to 5 P.M.)

Phone: (800) 831-7133

Fax: (919) 566-8920

Moorpark, California (8 A.M. to 5 P.M.)

Phone: (800) 831-7133

Fax: (800) 284-4151

Web sites: visit www.pentairpool.com and www.staritepool.com

Related IntelliTouch Manual

IntelliTouch ScreenLogic User’s Guide (P/N 520493)

© 2006 Pentair Water Pool and Spa, Inc. All rights reserved.

1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-800010951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 523-2400

This document is subject to change without notice.

Trademarks and Disclaimers. The trademark IntelliTouch is a registered trademark of PentairWater Pool and Spa, Inc. ScreenLogic is a trademark of Pentair Water Pool and Spa, Inc. Othertrademarks and trade names may be used in this document to refer to either the entitiesclaiming the marks and names or their products. Pentair Water Pool and Spa, Inc. disclaimsproprietary interest in marks and names of others.

P/N 520663 - Rev B 06/22/06


8

Step 2:Connect the ScreenLogic Indoor Wireless Transceiver to theScreenLogic Protocol Adapter

To connect the ScreenLogic indoor wireless transceiver to theScreenLogic Protocol adapter:

1. Using the provided connection cable, connect one end of thecable to the ScreenLogic Protocol adapter and the other endto the ScreenLogic indoor wireless transceiver. The cableplugs are keyed for easy connection.

2. Plug the ScreenLogic Wireless Connection transceiver ACadapter wall-plug into an AC grounded electrical outlet.

ScreenLogic ProtocolAdapter

1 ft. connection cable(provide in kit)

ScreenLogic indoor wirelesstransceiver

Protocol Adapter <----------> Indoor wireless transceiverRED (Pin 4) <----------> RED (Pin 1)YELLOW (Pin 3) <----------> GREEN (Pin 2)GREEN (Pin 2) <----------> YELLOW (Pin 5)BLACK (Pin 1) <----------> BLACK (Pin 6)

Wiring Configuration

Protocol Adapter

LA

N

LABEL P/N 520535

RE

SE

T

SERI

AL C

ONNE

CTIO

N

Blac

k G

reen

Yello

w R

ed

P/N 520489


Contents

i

Introduction ........................................................................................... 1

ScreenLogic Wireless Connection Kit Contents ..................................... 1

In this Installation Guide ....................................................................... 1

Summary installation steps ................................................................... 1

Step 1: Mount the Outdoor Wireless Transceiver and Connect to theIntelliTouch Load Center ........................................................................ 3

Step 2: Connect the Indoor Wireless Transceiver to the ScreenLogicProtocol Adapter ................................................................................... 8

FCC Regulatory Safety Notice - This equipment has been tested and found tocomply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to tryto correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.• Modifications not expressly approved by the party responsible for FCC

compliance could void the user’s authority to operate the equipment.


7. After the connection has been completed, close the controlpanel into its original position and secure it with the twoaccess screws.

8. Install the front panel and secure it with the two retainingscrews.

9. Close the Load Center front door. Fasten the two springlatches.

10. Switch the power on to the IntelliTouch Load Center.

11. Proceed to the “Connect the ScreenLogic IndoorWireless Transceiver to the ScreenLogic ProtocolAdapter” on page 8.

7

Personality board COM PORT Pin configuration

Note: Install the ScreenLogic outdoor wirelesstransceiver within 10 feet from Load Center

1 DNG KLB

2 TD- NRG

3 TD+ LEY

4 V51 DER

COM PORT screwterminal connector onPersonality board

Transceiver caseBlack

Transceiver Connector(see page 4 for details)

GreenRed Yellow

1 2 5 6

BLKGRNYELRED


IntroductionYour ScreenLogic Wireless Connection kit consists of two wireless900 Mhz transceivers which provides a wireless connectionbetween the ScreenLogic Protocol adapter and the IntelliTouchLoad Center located at the equipment pad. This wirelessconnection eliminates the existing hard wire connection from insideyour home to the equipment pad.

ScreenLogic Wireless Connection Kit ContentsThe following items are included in the Wireless Connection kit. If anyitems are missing please contact Technical Support.

• One ScreenLogic indoor wireless transceiver with AC poweradapter and one foot connection cable with attached plugs.

• One ScreenLogic outdoor wireless transceiver with 10 footattached cable

• ScreenLogic Wireless Connection Installation Guide(this manual)

In this Installation GuideUse the information in this manual for installing the WirelessConnection kit contents.

• For ScreenLogic system operating instructions, refer to theScreenLogic User’s Guide (P/N 520493)

Summary installation stepsThe ScreenLogic connection diagram on page 2 shows the transceiverlocations and connections. To install the ScreenLogic WirelessConnection kit:

• Mount the transceiver antenna near the IntelliTouch LoadCenter and connect the transceiver to the Personality board(COM port) located in the IntelliTouch Load Center.

• Connect the ScreenLogic indoor wireless transceiver to theScreenLogic Protocol adapter. Plug the transceiver ACpower adapter into an AC wall-outlet and into the transceiverunit to power up the unit.

1


5. Route the four conductor transceiver connection cable intothe lower plastic grommet, up through the low voltageraceway to the Personality board.

6. Strip back the cable conductors ¼ in. Insert the wires into thescrew terminals of the COM PORT plug located on thePersonality board as shown below. Using a smallflat-blade screwdriver, secure the wires with the screws.Make sure to match the color coding of the four wires:

Pin 4 - Red = +15Pin 3 - Yellow = +DTPin 2 - Green = -DTPin 1 - Black = GND

6

Note: If necessary, multiple wiresmay be inserted into a singlescrew terminal.

IntelliTouch Personalityboard COM PORTS

(J7/J8) screw terminalconnector

Raceway

Control panelPersonality

board


12

34

WA

N

RJ11

RJ45

INT

ER

NE

T

12

34

WA

N

- L

AN

-

Exi

stin

g w

ired

orw

irele

ss r

oute

r(m

an

da

tory

)R

J11

for

DS

LC

oax

for

Cab

le

In-w

all

Touc

hS

cree

n

Wir

eles

s tr

ansc

eive

rco

nnec

ted

toP

erso

nalit

y bo

ard

(CO

M p

ort)

via

10’ c

able

Pro

toco

lA

dapt

er

Scr

eenL

ogic

Wire

less

rou

ter

Wire

less

Dig

ital T

able

tW

irele

ss P

DA

Indo

or C

ontr

olP

anel

(*)

Exi

stin

g P

C

Eth

erne

t cab

le (R

J45

- CAT

5)

Eth

erne

t ca

ble

(RJ4

5 -

CAT

5)

DS

L or

Cab

le M

odem

(RJ4

5)

Cab

le d

ista

nce

limits

:-

Eth

erne

t ca

ble

dist

ance

lim

it =

300

fee

t-

Fou

r-w

ire c

able

dis

tanc

e lim

it =

150

0 fe

etN

ote:

(*)

Opt

iona

l wiri

ng f

or e

xist

ing

Indo

orC

ontr

ol P

anel

. Tap

into

the

Ind

oor

Con

trol

Pan

el c

onne

ctor

or

pig

tail

off

the

four

-wire

cabl

e co

nnec

ted

to t

he P

erso

nalit

y bo

ard.

Tra

nsc

eiv

er

conn

ecte

d to

Scr

eenL

ogic

Pro

toco

l ad

apte

r

Load

Cen

ter

(Loc

ated

out

side

at

equi

pmen

t pa

d)

2

4-w

ire 1

foo

tca

ble

AC

pow

erad

apte

rScreenLogic Wireless Connection Kit Installation Guide

WARNING Switch OFF the main system power to the Load Centerbefore making any connections.

1. Unlatch the two front door spring latches, and open the door.

2. Remove the two retaining screws securing the high voltagecover-panel, and remove it from the load center enclosure.

3. Loosen the two access screws securing the control panel andfold it down.

5

Panel retainingscrew

(Cover-panelnot shown)

Accessscrew

Retainingscrew

Accessscrew

Control panel

Connect the Transceiver connection cable to the Personality board

IntelliTouch Load Center

4. With the control panel in the open position, you can accessthe Personality board connectors.


3

Step 1: Mount the Outdoor Wireless Transceiver and Connectto the IntelliTouch Load Center

The following describes how to mount the outdoor transceiver at alocation near the IntelliTouch Load Center and connect the four-wire cable to the Personality board located in the IntelliTouch LoadCenter.

Mount the Transceiver module

The Transceiver is a two-way radio device with an attached antennathat communicates to and from the IntelliTouch system. Mount thetransceiver at a convenient location (on a flat vertical surface) near theload center, at a minimum of 5 ft. above ground level to optimize thetransmit and receive operating range. To avoid signal interference,mount the transceiver 10 feet away from the IntelliTouch Load Center,any metal surface/structure, or air blower located in the immediate areaof the equipment pad.

1. Slide the transceiver case off the back plate. The transceivercable is routed through the lower exit hole (right side) at thebottom of the back plate. The connector on the other end ofthe cable plugs into the transceiver board. Open the plasticbag inside the case and remove the transceiver antenna andtransceiver case screws, and set them aside.

2. Position the back plate against the mounting surface so thatthe transceiver is oriented in an upright position (with theantenna pointing upwards). Use a pencil to mark the fourmounting points. Drill four 3/16 in. diameter holes into themounting surface.

3. Position the back plate (with attached connection wire) overthe mounting points and secure it with four screws.

4. CAUTION - Electrostatic Discharge (ESD): Hold thecircuit board from the edges. Do not touch the boardcomponents, electrostatic discharge can damage theboard. Carefully remove the transceiver circuit board fromits bag. While holding the transceiver circuit board on itsedges, screw the antenna on the board threaded post. Do notover tighten.

5. Carefully connect the connection cable plug onto thetransceiver circuit board.


Transceiver Module

4

6. Position the transceiver circuit board with antenna into the mountedback plate. Align the board to the left side of the back plate.

7. Slide the case over the circuit board and antenna into the back plate.You may need to reposition the transceiver board inside the case tofully close the case. Secure the circuit board in the case using thetwo retaining screws provided in the plastic bag.

8. Proceed to “Connect the Transceiver connection cable to the Personalityboard” on page 5.

Transceiver circuit board

Back plate

Retaining screws

Case

Cable exits from lower exithole (right side)

Antenna

Mounting point (4x)

Circuit board threaded post

BlackGreen

Red Yellow

Screw terminalconnector (4-wirecable connects tothe IntelliTouchPersonality board)

1 2 5 6

Pin numbers

Documents

ScreenLogic™ Wireless Connection Kit - pentair.com · Personality board COM PORT Pin configuration Note: Install the ScreenLogic outdoor wireless transceiver within 10 feet from