Upload
prabuddha987
View
106
Download
0
Tags:
Embed Size (px)
DESCRIPTION
SDR OMCB TEMPLATE
Citation preview
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 1 页
SUBNETWORK_ID TEMPLATE_VERSION SDR_VERSION
Sub Network ID Template Version
1,001 4.1.0 4.11.10.14P04
Base Station Soft Version
INTEGER: 0~4095
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 2 页
OP_SIGN BTS_NAME NE_ID NE_IP
Operate Sign Site Name Network Element ID
P: No operate
LIC313 7 10.93.64.97test 186 10.90.151.173
Network Element IP Address
80 characters at mostWithout & ' " < > # % / \ ? @ : , * |
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
O&M IP of Node B, should be unique in the whole network.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 3 页
SDR_TYPE RNC_ID BSC_ID
SDR Type RNC ID BSC ID
BS8700 2,005 1,001BS8700 2,005 1,001
BS8700BS8900ABS8800 U120BS8800 U240BS8800 GU360BS8900 U240BS8900 GU360BS8906BS8800 U120ABS8908BS8900 Z01S80BS8900 Z01S18BS8900 Z02USG
INTEGER: 0 to 65535.
GSM single-mode base station does not need to fill in.
INTEGER: 0 to 65535.
UMTS single-mode base station does not need to fill in.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 4 页
LONGITUDE LATITUDE LOCATION VENDOR_NAME
Longitude Latitude Location Vendor Name
180.0 90.0 Viettel Peru90.0 90.0 Viettel Peru
RANGE: -180 to 180.
Accurate to six digits after the decimal point.
RANGE: -90 to 90.
Accurate to six digits after the decimal point.
40 bytes at most, can be blank.
40 bytes at most, can be blank.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 5 页
USER_DEFINED_STATE
User Defined State
11
80 bytes at most, can be blank.
NE_ID CLOCK_PRIORITY CLOCK_TYPE CLOCK_SYNC_MODE
Network Element ID Clock Source Type Clock Synchronization Mode
INTEGER: 1 to 8
7 1 1588186 1 1588
Clock Source Priority
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
Internal GNSSExternal GNSSCascade GNSS1PPS+TODBITS-2MHzBITS-2MbpsLine1588SyncE
0: GSM/UMTS Frequency Sync,1: GSM FrameNumber Sync. UMTS Frequency Sync,2: GSM Frequency Sync. UMTS FrameNumber Sync,3: GSM/UMTS FrameNumber Sync
GPS_CABLE_TYPE GPS_RECEIVER_TYPE GPS_CABLE_DELAY
GPS Cable Type GPS Receiver Type
INTEGER: 0 to 15
Length of Cascade cable(m)
0: Multiplexing input1: Distribution input
1:GPS2:GLONASS3:GPS+GLONASS
CLOCK_SSM
Enable SSM
Y:YesN:No
Must be configured if CLOCK_ID is SyncE
NE_ID LINK_PRIORITY TRANS_TYPE
Network Element ID Link Priority IP Clock Transmission Mode
INTEGER: 1 to 32
7 1 1186 1 1
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
0:Multicast1:Unicast
default: 1
IPCLK_SYNC_SERVER_IP IPCLK_IP_NO
10.95.211.1 0110.9.1.49 0
IP Address of 1588 Clock Sync Server
IP Link No. of 1588 Clock Sync Channel
Must be configured for IP 1588 clock reference source(GIPI interface IP). Valid only when it is IP over Ethernet transmission type. If there are two or more 1588 servers, configure it as this: "IP1;IP2;...", with four IP addresses at most.
INTEGER: 0 to 19
Existed in IP sheet.
NE_ID NTP_SERVER_IP TIME_ZONE SUMMER_TIME_START
Network Element ID Time Zone Summer Time Start
IPV4
NTP Server IP Address
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
Pattern: MM-DD HH:mm.
Fill in '0' if not used
SUMMER_TIME_END
Summer Time End
Pattern: MM-DD HH:mm.
Fill in '0' if not used
NE_ID TELECOM_OPERATOR OPERATOR_PLANNED_ID
Network Element ID Telecom Operator
7 Viettel Peru186 Viettel Peru
Network Element ID planned by operator
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
127 bytes at most, without & ' " < > # %
48 bytes at most, without & ' " < > # %
Operator plans the unique network element ID for base station. Users cannot set the option if it is not be planed.
VENDOR_PLANNED_ID RADIO_MODE BBU_TYPE BBU_SLOT_1
Radio Mode BBU Type BBU Slot 1
GSM+UMTS BBU-2U CCGSM+UMTS BBU-2U CC
Network Element ID planned by vendor
48 bytes at most, without & ' " < > # %
Vendor plans the unique network element ID for base station. Users cannot set the option if it is not be planed.
UMTSGSMGSM+UMTS
BBU-2UBBU-3UDIET
CCCCCTRB-G904TRB-G184TRB-G194TRB-G854
BBU_SLOT_2 BBU_SLOT_3 BBU_SLOT_4 BBU_SLOT_5
BBU Slot 2 BBU Slot 3 BBU Slot 4 BBU Slot 5
FSFS
CCCCCUES
Keep empty or remove the column if there isn't a board.(It's applies to all BBU Slot)
FSUBPG2BPLUESUBPG(only available in BBU-3U)
BPCFSUBPGUBPG2TAM0TAM1TAM2BPLUESUBPG3
BPCUBPGBPKUBPG2SEUESTAM0TAM1TAM2USR1-ABPLUBPG3BPK-s
BBU_SLOT_6 BBU_SLOT_7 BBU_SLOT_8 BBU_SLOT_9 BBU_SLOT_10
BBU Slot 6 BBU Slot 7 BBU Slot 8 BBU Slot 9 BBU Slot 10
BPC UBPGBPC UBPG
BPCUBPGBPKUBPG2SEUESTAM0TAM1TAM2USR1-ABPLUBPG3BPK_s
BPCUBPGBPKUBPG2SEUESTAM0TAM1TAM2USR1-ABPLUBPG3BPK_s
BPCUBPGBPKUBPG2SEUESTAM0TAM1TAM2BPLUBPG3BPK_s
UBPGUES
only available in BBU-3U
UBPGUES
only available in BBU-3U
BBU_SLOT_11 BBU_SLOT_12 BBU_SLOT_14 BBU_SLOT_15
BBU Slot 11 BBU Slot 12 BBU Slot 14 BBU Slot 15
PM
PMPM
UBPGUES
only available in BBU-3U
UBPGUES
only available in BBU-3U
PMSE(only available in BBU-3U)
BBU_SLOT_16 BBU_SLOT_17 SHELF2_BBU_SLOT_1 SHELF2_BBU_SLOT_2
BBU Slot 16 BBU Slot 17 Shelf 2's BBU Slot 1 Shelf 2's BBU Slot 2
PM
only available in BBU-3U
PM
only available in BBU-3U
CCCCC
CCCCCUES
SHELF2_BBU_SLOT_3 SHELF2_BBU_SLOT_4 SHELF2_BBU_SLOT_5 SHELF2_BBU_SLOT_6
Shelf 2's BBU Slot 3 Shelf 2's BBU Slot 4 Shelf 2's BBU Slot 5 Shelf 2's BBU Slot 6
FSUBPG2BPLUES
BPCFSUBPGUBPG2TAM0TAM1TAM2BPLUESUBPG3
BPCUBPGBPKUBPG2SEUESTAM0TAM1TAM2USR1-ABPLUBPG3BPK_s
BPCUBPGBPKUBPG2SEUESTAM0TAM1TAM2USR1-ABPLUBPG3BPK_s
SHELF2_BBU_SLOT_7 SHELF2_BBU_SLOT_8 SHELF2_BBU_SLOT_14
Shelf 2's BBU Slot 7 Shelf 2's BBU Slot 8 Shelf 2's BBU Slot 14
BPCUBPGBPKUBPG2SEUESTAM0TAM1TAM2USR1-ABPLUBPG3BPK_s
BPCUBPGBPKUBPG2SEUESTAM0TAM1TAM2BPLUBPG3BPK_s
PM
SHELF2_BBU_SLOT_15 RACK_TOPOLOGY FS3_OPTICAL_MODULE_TYPE
Shelf 2's BBU Slot 15 Rack Topology
PM
1-51 1.25G1-51 1.25G
Optical Module Type of FS in Slot 3
Pattern:1-RU-RU-...,1-RU-RU-... For example, "1-2-3,1-4,1-51-52" means RSU2 and RSU4 and RRU51 connect with the main rack, RSU3 connects with RSU2, RRU52 connects with RRU51. Keep blank if there is no cascade connection.
1.25G2.5G3G6G
FS4_OPTICAL_MODULE_TYPE
Optical Module Type of FS in Slot 4
1.25G2.5G3G6G
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 23 页
NE_ID RRU_NAME RU_NO BOARD_TYPE
Network Element ID RRU Name RU No. Board Type
7 51 ADTR-GU1987 52 ADTR-GU1987 53 ADTR-GU198
186 51 ADTR-GU198186 52 ADTR-GU198
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
60 characters at most, can be blank. Without& ' " < > # % / \ ? @ : ,
RSU: 2 to 50RRU: 51 to 201DIET: 1 to 3
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 24 页
FS_PORT OPTICAL_MODULE_TYPE ANTENNA_TYPE VSWR_LOWER
Previous Hop Optical Port Optical Module Type Antenna Type
Integer
0 1.25G RET 2001 1.25G RET 2002 1.25G RET 2000 1.25G RET 2001 1.25G RET 200
VSWR Lower Limit
Shelf 1's FS-3: 0 to 5Shelf 1's FS-4: 20 to 25Shelf 1's UBPG2-3: 0 to 2Shelf 1's UBPG2-4: 20 to 22Shelf 1's UBPG2-8: 80 to 82
Shelf 2's FS-3: 10~15
Shelf 2's FS-4: 30~35
Shelf 2's UBPG2-3: 10~12
Shelf 2's UBPG2-4: 30~32
Shelf 2's UBPG2-8: 85~87
Only GSM BTS can use UBPG2 as parent topo.
1.25G2.5G3G6G
R8840、R8860、RU02 series must be 1.25G. All of RU linked to same FS port must be identical.
ANT:Normal AntennaRET:Aisg
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 25 页
VSWR_UPPER LOWER_RESUME_LIMIT UPPER_RESUME_LIMIT DIVERSITY_MODE
Diversity Receiving Mode
Integer Integer Integer
300 190 290 0300 190 290 0300 190 290 0300 190 290 0300 190 290 0
VSWR Upper Limit
Alarm Recovery Lower Limit of VSWR
Alarm Recovery Upper Limit of VSWR
0:Normal diversity reception1:Cross diversity receptiondefault: 0
NE_ID RU_NO PADEV_NO RADIO_MODE
Network Element ID RU No. PA Device No. Radio Mode
7 51 1 GSM+UMTS7 52 1 GSM+UMTS7 53 1 GSM+UMTS
186 51 1 GSM+UMTS186 52 1 GSM+UMTS
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
RSU: 2 to 50RRU: 51 to 201
INTEGER: 1 to 3
The second PA is 2,The third PA is 3
UMTSGSMGSM+UMTS
TRANSMIT_FREQ
0.00.00.00.00.0
Central Downlink Frequency(MHz)
Multiple of 0.2MHz. 0 or blank represents automatical calculation by Node B
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 28 页
NE_ID FCE_RACK_NO CTRL_AUX_CABINET_NO
Network Element ID FCE Rack NoControlled auxiliary cabinet
No.INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
2 to 50119 to 123: FCE in 1-1-19 to 1-1-23
Fill out the attribute for the FCE in an auxiliary cabinet, Can not be duplicate.
NE_ID RU_NO RX_PORT_NO
Network Element ID RU No. Rx Port ID
INTEGER: 1 to 6
7 51 27 51 17 52 27 52 17 53 27 53 1
186 51 1186 51 2186 52 1186 52 2
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
RSU: 2 to 50RRU: 51 to 201
RECEIVE_FREQ RX_EXTENSION_RU RX_EXTENSION_PORT
Rx RF Extension RU No. Rx RF Extension Port ID
INTEGER: 1 to 6
0.00.00.00.00.00.00.00.00.00.0
Central Uplink Frequency(MHz)
Multiple of 0.2MHz. 0 or blank represents automatical calculation by Node B. When downlink frequency is not 0, uplink frequency should not be 0.
The frequency band of associated RU should be identical. Each RU can only be associated once.
TMA_NO TM_TYPE RX_POWER_GAIN
TMA No. Tower Top Amplifier type
INTEGER: 1 to 96
Tower Top Amplifier Uplink Power Gain
TMAA-TMAA-COMETMAA-ETMA
TMA: 70 to 150A-TMA: 44 to 100A-COM: 0 to 14ETMA: 200 to 320A-ETMA: 92 to 100Invalid: 65535
TX_POWER_GAIN TMA_NOISE ANT_NO RET_NO
Tower Top Amplifier Downlink Power
Gain(0.1db)
Tower Top Amplifier Noise
Coefficient(0.1dB)
Connected Mechanical
Antenna RDN
Connected RET Antenna RDN
INTEGER:70 to 170Invalid:255
INTEGER: 10 to 30Invalid:255
This field can not be configured. Do not modify it.
This field can not be configured. Do not modify it.
NE_ID EPM_BOARD EPM_PWR_TYPE
Network Element ID Connected Board Epm Power Type
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
SASE-SlotNo2-SA: SA in shelf 22-SE-SlotNo: SE in shelf 2
ZXDU58 B900ZXDU58 B121ZXDU68 B201ZXDU150ZXDU45ZXDU75ZXDU58 B121(V4.5)ZXDU68 B201(V5.0)ZXDU68 W301ZXDU68 S301ZXDU58 B121(V2.2)
EPM_DEAL_MODE
EPm Data Processing Mode
0:Transparent transmission,1:Parse
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 35 页
NE_ID DRY_CONTACT_POSITION DRY_CONTACT_NO
Network Element ID Dry Contact Position Dry Contact No.
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
SASE-SlotNo2-SA: SA in shelf 22-SE-SlotNo: SE in shelf 2
FCE (1-1-18)FCE-RackNo
If position is RU, the pattern is RU-No., example:RU-51.
The boards that support dry contact alarms are SA, FCE boards, and radio frequency boards.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 36 页
DRY_CONTACT_USERLABEL DRY_CONTACT_TYPE
User Label Dry Contact Type
128 bytes at most, can be blank. Without& ' " < > # % / \ ? @ : ,
Input:Input dry contactOutput:Output dry contact
Output dry contact should be linked to contact No.6 or 7 of SA/SE.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 37 页
DRY_CONTACT_CONTENT ALARM_STATUS
Dry Contact Alarm Code Dry Contact Alarm Status
198092044:Door control alarm 198092045:Flooding alarm 198092046:Smog alarm 198092047:Infrared alarm 198092048:Air conditioner fault 198092049:Lightning protection device alarm198092051:PSU alarm 198092052:PSU fan alarm 198092068:Base station has a main power cut-off alarm198092206:Battery alarm 198092207:AC power-cut alarm 198092208:Rectifier module alarm 198092209:Thermoelectric cooler alarm 198092259:Battery low-voltage alarm 198092260:Faulty external device connected at a dry contact 198092261:Outdoor lightning protection box alarm 198092262:Breaker alarm in indoor lightning protection box
Valid only if type is input. OPEN:Alarm appears if contact is openCLOSE:Alarm appears if contact is closed
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 38 页
OUT_CONTACT_TYPE
Output Dry Contact Status
Valid only if type is output. 0:Output low level1:Output high level
NE_ID TAM_SHELF TAM_SLOT
Network Element ID TAM Board Shelf No. TAM Board Slot No.
INTEGER: 1 to 2 INTEGER: 1 to 23INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
TAM_PORT TAM_WORKING_CURRENT TAM_ALM_MODE
TAM Board Port No. Alarm Detect Mode
INTEGER: 0 to 5
Work Current Value(mA)
TAM0: 75 to 300TAM1: 75 to 400TAM2: 75 to 400
Configure the maximum current value of the specified port.
0:currentDetect1:pulsewidthDetect
NE_ID AISG_RU_NO UNIQUE_ID DEV_TYPE
Network Element ID CCU Rack No. Device Serial Number Device Type
32 bytes at mostINTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
RSU:2 to 50
RRU:51 to 201
Existed in RU sheet.
RETCMULTI_RETATMAMULTI_TMAACOMAETMANSNRETLGPTMA
VENDOR_CODE AISG_VERSION RET_RU_NO
Vendor Code AISG Version Connected RET Device RU No
127 bytes at most 1.12.0
RSU: 2 to 50RRU: 51 to 201
Existed in RxDevice sheet and ANTENNA_TYPE must be RET. It indicates AISG_TMA_NO bearer.
RET_PORT_NO AISG_TMA_NO MULTI_ANT_NO
Subunits No.Connected RET Device Port
NoConnected TMA
Device No.INTEGER: 1 to 6
Existed in RxDevice sheet and ANTENNA_TYPE must be RET. It indicates AISG_TMA_NO bearer.
INTEGER: 1 to 96
Existed in RxDevice sheet. Indicates RET_RU_NO and RET_PORT_NO bearer.
INTEGER: 1 to 4255:Invalid
The antenna number of AISG1.1 and AISG2.0 Single RET decives is invalid. A subunit No. of other AISG2.0 devices corresponds to an AISG that can be controlled independently.
AISG_USERLABEL FATHER_PORT SELF_PORT
Superior Channel Local ChannelDescription of Self-
defined Field128 bytes at most, can be blank. Without& ' " < > # % / \ ? @ : ,
INTEGER: 0 to 12
Used for SDTMA device of NSN private protocol. The value for other devices is 0.
INTEGER: 0 to 12
Used for SDTMA device of NSN private protocol. The value for other devices is 0.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 45 页
NE_ID TRANSMISSION_TYPE TRANSMISSION_MEDIUM
Network Element ID Transmission Type Transmission Medium
7 IP FE186 IP FE
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
IPATMATM+IP
FEE1T1FE+E1FE+T1
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 46 页
ETHERNET_WORK_MODE FE_BANDWIDTH FE_PHYLAYERPORTNO
Ethernet Mode FE/GE BandWidth(kbps)
INTEGER: 0 to 17
Auto 21,000 0Auto 21,000 0
FE/GE Physical Layer Port No.
Auto1000M100M10M100M-Fiber
INTEGER:100 to 1000000. Step 100
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 47 页
NE_ID ATM_E1T1_PHYLAYERPORT_NO
Network Element ID ATM E1/T1 Physical Layer Port No.
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
Pattern: portNo,portNo,.. portNo:0 to 17. Must be existed in E1T1 sheet
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 48 页
ATM_ADDRESS
ATM Address
Pattern: dec.dec…Keep blank if not used
NE_ID E1T1_PHYLAYERPORT_NO E1T1_SHELF
Network Element ID E1T1 Board Shelf No.
INTEGER: 0 to 17 INTEGER: 1 to 2
E1/T1 Physical Layer Port No.
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
E1T1_BOARD E1T1_PORT
E1T1 Board Type E1/T1 Port No.
INTEGER: 0 to 7SASE-5SE-14TRB Series.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 51 页
NE_ID HDLC_NO HDLC_E1T1_PHYLAYERPORT_NO
Network Element ID HDLC Link No. E1/T1 Physical Layer Port No.
INTEGER: 0 to 15INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
INTEGER: 0 to 17
Must be existed in E1T1 sheet
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 52 页
HDLC_TIMESLOT_MAP TSI_IN_TIMESLOT_MAP TSI_OUT_PHYLAYERPORT_NO
HDLC Timeslot TSI In Timeslot TSI Out Physical Layer Port No.
Pattern:start of time slot-end of time slot,... Slot 1 to 31(T1 is 24) can be used. Slot 0 is excluded.Default: 1-31
The pattern is same as HDLC timeslot. can not overlap with the HDLC timeslot. should be filled in case of time slot interchange, otherwise keeping empty.
INTEGER: 0 to 17.
Should be filled in case of time slot interchange, otherwise keeping empty.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 53 页
TSI_OUT_TIMESLOT_MAP TSI_OUT_NO
TSI Out Timeslot TSI Out No.
The pattern is same as HDLC timeslot. The number of out&in timeslot must be identical. should be filled in case of time slot interchange, otherwise keeping empty.
This field can not be configured. Do not modify it.
NE_ID IP_NO IP_VLAN_ID IP_VLAN_IP_ADDR
Network Element ID IP No. IP Vlan No. IP Address
INTEGER: 0 to 19 IPV4
7 1 3,033 10.95.64.977 0 3,032 10.93.64.97186 0 10.90.151.173186 1 110.9.1.50
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
INTEGER: 1 to 4094.
Keeping empty if it's invalid.
IP_VLAN_MASK IP_VLAN_GATEWAY STATICROUTE_IPADDRESS
IP Subnet Mask IP Gateway Address
IPV4 IPV4
255.255.255.224 10.95.64.126255.255.255.224 10.93.64.126255.255.255.0 10.90.151.254255.255.255.0 110.9.1.49
Static Route Destination IP Address
IPV4can be blank.
STATICROUTE_NETWORKMASK STATICROUTE_NEXTHOP_IPADDR PATH_DOMAIN
Static Route Network Mask Static Route Next Hop IP Address Path Domain
IPV4can be blank.
IPV4can be blank.
INTEGER: 0~3255: Invalid
UMTS multi-path parameter
PPP_NO PPP_HDLC_NO PPP_IP_ADDRESS PPP_PROTOCOL
PPP No. PPP HDLC Link No. PPP EncapsulationBase Station IP
AddressINTEGER: 0 to 7. ML-PPP: 0 to 2
Pattern: hdlc No.,hdlc No.,... hdlc No.:0 to 15, 8 links at most.
IPV4. "0.0.0.0" represents automatic allocation.
PPPML-PPP
PPP_COMPRESSION MP_HEAD MP_PRIORITY
Support IP compress or not MP Head MP Priority
Y:supportN:non-support
PPP does not support IP compress.
LongShortInvalid
Valid when encapsulation type is ML-PPP.
1234INVALID
Valid when encapsulation type is ML-PPP.
QOSMAP_NO
QosMap No.
1001
This field can not be configured. Do not modify it.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 60 页
NE_ID SCTP_NO SCTP_RADIO_MODE SCTP_LOCAL_PORT
Network Element ID SCTP No. SCTP Radio Mode SCTP Local Port
INTEGER: 0 to 3
7 1 UMTS 1077 0 GSM 7186 0 GSM 1186 1 UMTS 186
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
GSMUMTS
UMTS:0 to 65535GSM:1 to 1536, it is Site Id.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 61 页
SCTP_REMOTE_PORT SCTP_REMOTE_IP SCTP_IP_NO
SCTP Remote Port IP No. of SCTP Channel
IPV4
107 10.95.205.129 114,595 10.91.130.1 014,595 10.91.210.1 0186 10.95.205.129 1
SCTP Remote IP Address
UMTS:0 to 65535GSM: iBSC CMP module No. + 0x3900
INTEGER: 0 to 19
Existed in IP sheet.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 62 页
SCTP_INOUT_STREAM SCTP_QOS
SCTP QOS
Integer: 2 to 6
2 462 462 462 46
Number of SCTP in-and-out Streams
Integer: 0 to 63
IP service model configuration. You can choose different model according to the actual scenario.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 63 页
NE_ID OMC_CHANNEL_NO OMCB_GATEWAY_IP OMCB_IP_NO
Network Element ID OMC Channel Link No. OMC Used IP No.
Integer: 0 to 2 IPV4
7 0 10.91.130.254 0186 0 10.91.130.254 0
OMC Gateway IP Address
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
INTEGER: 0 to 19
Existed in IP sheet.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 64 页
OMC_SERVER_IP INNER_IP OMCB_QOS
OMC Server IP Address SDR inner ip address
IPV4 IPV4
10.121.13.1 4610.121.13.1 46
Operation and Maintenance Gateway QoS
Integer: 0 to 63
The transmission quality priority of O&M packet. It is set by the user. It is recommendedto set it to "46:EF service, accelerated forwarding, minimum delay, and maximum flow".
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 65 页
NE_ID NODEB_ID CE_UP CE_DOWN
Network Element ID NodeB ID CE Up CE Down
7 7 189 123186 186 189 123
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
INTEGER: 0 to 65535.
Same as NE ID if radio mode is UMTS.
INTEGER: 1 to 384065535:Invalid
INTEGER: 1 to 384065535:Invalid
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 66 页
DYNAMIC_POWER_TRACK PASHARE_PER
RU Dynamic Power Track Power-sharing Ratio
INTEGER: 0 to 50
N 0N 0
Y: Function openedN: Function closed
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 67 页
NE_ID UMTS_SECTOR_ID UMTS_SECTOR_INFO RELATED_RU
Network Element ID Sector No. Sector Information Related RU
INTEGER: 0 to 255
7 0 517 1 527 2 53186 0 51186 1 52
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
199 bytes at most, can be blank. Without& ' " < > # % / \ ? @ : ,
RU Units belong to this sector. Pattern: RU No.&RU No.&…The second PA of RU is:'RU No.#2'
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 68 页
RX_TYPE RFRX_ORDER
Rx Type RFRx Line Order
Y 0Y 0Y 0Y 0Y 0
Y: DiversityN: No DiversityMIMO
0: Normal1: ReversePattern: RU Order&RU Order&…If all of the RU order is the same, fill in '0' or '1'
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 69 页
NE_ID LOCAL_CELL_INFO LOCAL_CELL_ID
Network Element ID Local Cell Information Local Cell ID
7 30,1317 30,1327 30,133186 1186 2
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
199 bytes at most, can be blank, without& ' " < > # % / \ ? @ : ,
INTEGER: 0 to 268435455.
Unique in the network.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 70 页
BP_BOARD AUTOASSIGN_BASEBAND_RESOURCE UMTS_SECTOR_ID
BP Board Sector No.
7 Y 07 Y 17 Y 27 Y 07 Y 1
Automatically assign baseband resource or not
Fill in BPC and BPK's slot number.Pattern: BPSlot&BPSlot&…Plus 20 for slot number of shelf 2's BP board.
YN
Refers to the sheet "UMTS Sector"
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 71 页
TRANSMITTING_FREQ FREQ_SPACING CELL_RADIUS TRANSMIT_OFFSET
Cell Radius
Integer: -63 to 63
1,983.6 5M 5km 01,983.6 5M 5km 01,983.6 5M 5km 01,983.6 5M 5km 01,983.6 5M 5km 0
Transmitting Frequency(MHz)
Receive Filter BandWidth
Transmit Delay Offset(chip)
Multiple of 0.2MHz.869 to 894925 to 9601805 to 18801930 to 19902110 to 2170
5M4.8M4.6M4.4M4.2M3.8M
2.5km5km10km20km40km80km120km240km
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 72 页
RECEIVE_OFFSET LOCAL_CELL_POWER SUPPORT_SPEED COVERAGE_TYPE
Local Cell Power(W) Coverage Type
Integer: -63 to 63
0 20 0 10 20 0 10 20 0 10 20 0 10 20 0 1
receive Delay Offset(chip)
Mobile Speed Supported by Cell
INTEGER: 1 to 200255:Invalid
0:0-250km/h1:250-350km/h
0:Indoor1:Outdoor
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 73 页
DC_LOCAL_CELL BATTERY_SAVING LOCAL_CELL_2MS_GAIN
Dual Carrier Secondary Local Cell Electric-saving Mode 2ms Gain
N EnableN EnableN EnableN EnableN Enable
Primary and secondary local cell must belong to the same sector, and is neighboring cells(transmission frequency interval is between 3.8 and 5MHz)
Y:Function openedN:Function closed
Enable:supportDisable:non-support
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 74 页
LOCAL_CELL_VAM ENHANCED_VAM
VAM Function
N NN NN NN NN N
Enable E-VAM function or not
Y:supportN:non-support
It can be set as "Y" only when Rx type of affiliated sector is MIMO.
Y:Enable
N:Disable
In the case of vamEnable being Y, it decide whether to enable E-VAM function.
NE_ID CELL_ID GPS_OFFSET
Network Element ID Cell No.
INTEGER: 1 to 54 INTEGER: 0 to 50
7 1 0186 1 0
GPS Synchronous Frame Header Offset
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
POINT1_RU_NO POINT2_RU_NO BCCH_RU_NO
BCCH preferential RU No.High speed railway cell entry
point 1 RU No.High speed railway cell entry
point 2 RU No.
The second PA of R8882、RSU82 is:'RU No.#2'. Can be blank
The second PA of R8882、RSU82 is:'RU No.#2'. Can be blank
The second PA of R8882、RSU82 is:'RU No.#2'. Can be blank
BCCH_TRU_NO
Can be blank
BCCH preferential Carrier No.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 78 页
NE_ID GRU_NO CHANNEL_GROUP_NO GU_CONFIG_MODE
Network Element ID GSM RU No. GU Carrier Config Mode
7 51 0 4G+1U7 52 0 4G+1U7 53 0 4G+1U
186 51 0 4G+1U186 52 0 4G+1U
GSM Cell Channel Group No.
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
RSU: 2 to 50RRU: 51 to 201
The second PA of R8882、RSU82 is:'RU No.#2'
INTEGER: 0 to 216
GSM Cell Channel Group No. 0 indicates no grouping. When Carrier Group is greater than zero,GSM Cell Channel Group No must be greater than zero.
4G+1U2G+2UINVALID
Single radio mode is INVALID.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 79 页
CARRIER_GROUP CARRIER_NUMBER CARRIER_POWER_PARA STATIC_POWER_LEVEL
Carrier Group Total Carrier Number Carrier Power(W) Static Power Level(db)
INTEGER: 1 to 80
0 2 20 2db0 2 20 2db0 2 20 2db0 2 20 2db0 2 20 2db
INTEGER: 0 to 32. 0:Do not group
DTR:1 to 6TTR:1 to 2RSU82:1 to 4R8882: 1 to 6
0db, 2db, 4db, 6db, 8db, 10db, 12db, 14db, 16db, 18db, 20db, -0.2db, -0.4db,-0.6db, -0.8db, -1.0db, -1.2db
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 80 页
CELL_ID_1 TRX_NUMBER_1 CELL_ID_2 TRX_NUMBER_2
First GSM Cell No. Second GSM Cell No.
INTEGER: 1 to 54
1 21 11 21 11 2
Carrier Number dedicated to first sector
Carrier Number dedicated to second
sector
INTEGER: 1 to 6
The sum total of all sector's carrier number is not greater than the Total Carrier Number.
INTEGER: 1 to 54255: Invalid
INTEGER: 1 to 6
The sum total of all sector's carrier number is not greater than the Total Carrier Number.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 81 页
CELL_ID_3 TRX_NUMBER_3 CELL_ID_4 TRX_NUMBER_4
Third GSM Cell No. Fourth GSM Cell No.
INTEGER: 1 to 54
Carrier Number dedicated to third
sector
Carrier Number dedicated to fourth
sector
INTEGER: 1 to 6
The sum total of all sector's carrier number is not greater than the Total Carrier Number.
INTEGER: 1 to 54255: Invalid
INTEGER: 1 to 6
The sum total of all sector's carrier number is not greater than the Total Carrier Number.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 82 页
CELL_ID_5 TRX_NUMBER_5 CELL_ID_6 TRX_NUMBER_6
Fifth GSM Cell No. Sixth GSM Cell No.
INTEGER: 1 to 54
Carrier Number dedicated to fifth sector
Carrier Number dedicated to sixth
sector
INTEGER: 1 to 6
The sum total of all sector's carrier number is not greater than the Total Carrier Number.
INTEGER: 1 to 54255: Invalid
INTEGER: 1 to 6
The sum total of all sector's carrier number is not greater than the Total Carrier Number.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 83 页
SUB_FREQ_BAND TX_MODE RX_MODE
Tx Mode Rx Mode
255 0 0255 0 0255 0 0255 0 0255 0 0
Branch Frequence Band
INTEGER: 1 to 3. 255: Invalid
0:Normal mode1:DPCT2:DDT3:Antenna hopping
RU02: series:0 to 3, RSU82/R8882:{0,2,3}. Other RU types should be blank. Default:0
0:2-antenna diversity reception1:4-antenna diversity reception
Only RU02/RSU82/R8882 can be configured as 4-antenna diversity reception.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 84 页
DDT_OFFSET GSM_RX_CONFIG GSM_NO
DDT delay
0 00 00 00 00 0
GSM primary-secondary antenna receiving setting
GSM Cell Channel Resource No.
INTEGER: 0 to 8.
Be valid when tx mode is DDT. Default:0
0:Primary and secondary antenna receiving,1:Primary antenna receiving. secondary antenna not receiving,2:Secondary antenna receiving. primary antenna not receiving
This field can not be configured. Do not modify it.
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 85 页
NE_ID CELL_ID TRX_NO CHANNEL_MODE
Network Element ID Cell No. Channel Mode
INTEGER: 1 to 54 INTEGER: 1 to 60
7 1 2 SINGLE186 1 1 SINGLE
Logic Carrier Frequency No.
INTEGER: 0 to 65535.
Should be unique in the whole subnetwork. Index of all sheets.
0:Single carrier1:Dual carrier2:Multi carrier
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 86 页
CARRIER_GROUP FREQ_BAND SUB_FREQ_BAND USE_IRC
Carrier Group Frequency Band Use IRC or Not
0 1900M 255 10 1900M 255 1
Branch Frequence Band
INTEGER: 0 to 32. 0:Do not group
2.1G1900M1800M850M900M
INTEGER: 1 to 3. 255: Invalid
0:Disable IRC1:Enable IRC2:Enable STIRC
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 87 页 , 第 87 页
EXTENSION_CARRIER MCUM_RX_SEL_MODE MCUM_TX_SEL_MODE
N N NN N N
Extend Carrier Frequency or Not
Is uplink signal selected according to
CIR
Select RU transmission or not
Y:YesN:No
Y:YesN:No
default:N
Y:YesN:No
default:N