Upload
rusten2
View
265
Download
0
Embed Size (px)
Citation preview
8/11/2019 Sea Doo Shop Manual (2005)
1/314
8/11/2019 Sea Doo Shop Manual (2005)
2/314
Vehicle Shop M
8/11/2019 Sea Doo Shop Manual (2005)
3/314
Legal deposit:
National Library of QuebecNational Library of Canada 2005
All rights reserved. No parts of this manual may be reproduced in any form without the ppermission of Bombardier Recreational Products Inc. (BRP)
Bombardier Recreational Products Inc. (BRP) 2005
Technical PublicationsBombardier Recreational Products Inc. (BRP)Valcourt (Quebec) Canada
Printed in Canada
TM
Registered trademarks of Bombardier Recreational Products Inc. (BRP) or its affiliates.* Trademark of Bombardier Inc. used under license.
SEA-DOO
BOMBARDIER-ROTAX
BOMBARDIER LUBE
Sea-Doo Learning KeyTM
DESSTM
Rotax
O.P.A.S.TM
TOPSTM
This document contains the trademarks of the following companies:
Knights Spray-Nine is a trademark of Korkay System LtdGTX is a trademark of Castrol Ltd. Used under license
8/11/2019 Sea Doo Shop Manual (2005)
4/314
TABLE
SAFETY NOTICE ................ ................ ................. ..............
INTRODUCTION ................ ................ ................. ..............GENERAL INFORMATION.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ARRANGEMENT OF THIS MANUAL .... .... .... .... .... .... .... ... .... .... ... .... ....
ABBREVIATIONS USED IN THIS MANUAL ... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ..
ILLUSTRATIONS AND PROCEDURES ...... ... .... .... .... .... .... .... .... ... .... ....
ENGINE EMISSIONS INFORMATION ... .... ... .... .... .... .... .... .... .... ... .... ....
SELF-LOCKING FASTENERS PROCEDURE ... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ..
LOCTITE APPLICATION PROCEDURE...... .... ... .... .... ... ... ... .... .... ... .... ....TIGHTENING TORQUES .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
01 MAINTENANCE01 MAINTENANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02 PRE SE AS ON P RE PARAT IO N .. .... .... .... ... .... .... ... ... ... .... .... ... .... ....
03 STO RAGE PRO CEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROPULSION SYSTEM.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FUEL SYSTEM.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE OIL AND FILTER REPLACEMENT ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPENED LOOP COOLING SYSTEM ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLOSED LOOP COOLING SYSTEM (ENGINE) .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE LUBRICATION.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THROTTLE BODY LUBRICATION.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ANTIFREEZING PROTECTION ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BATTERY. . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WATERCRAFT CLEANING.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ANTICORROSION TREATMENT .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKLIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
04 SPECIAL PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOWING THE WATERCRAFT IN WATER.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SUBMERGED WATERCRAFT .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WATER-FLOODED ENGINE .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02 TROUBLESHOOTING01 TRO UBLESHO OTING C HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE WILL NOT START .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE HARD TO START.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE STARTS BUT RUNS ONLY AT IDLE SPEED.. ... .. ... ... .. ... .. ... ... .. ... ..
ENGINE MISFIRES, RUNS IRREGULARLY.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE CONTINUALLY BACKFIRES... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE DETONATION OR PINGING.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE LACKS ACCELERATION OR POWER ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE STOPS RUNNING
8/11/2019 Sea Doo Shop Manual (2005)
5/314
TABLE OF CONTENTS
03 ENGINE SYSTEM01 AIR IN TAKE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSPECTION.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02 LUBRICATION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OIL LEVEL VERIFICATION... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OIL CHANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OIL TYPE AND SYSTEM CAPACITY.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .OIL FILTER.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
03 COOL IN G SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLOSED LOOP COOLING SYSTEM (ENGINE) .. ... ... .. ... ... .. ... ... .. ... ... .. ... ... .. ... ...
CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COOLING SYSTEM LEAK TEST... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSPECTION.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COOLANT REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CARE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . .
TECHNICAL SPECIFICATIONS.. .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPENED LOOP COOLING SYSTEM (EXHAUST SYSTEM)... .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .
CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CARE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . .
TECHNICAL SPECIFICATIONS.. .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
04 EXHA UST SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXHAUST PIPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXHAUST MANIFOLD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MUFFLER.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RESONATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXHAUST OUTLET.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
05 REMO VAL AND IN STALLAT IO N... .... .... .... .... ... .... .... ... .... .... ... ... ... .... .... .... ...
ENGINE REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
04 ENGINE MANAGEMENT (1503 4-TEC)
01 OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATING PRINCIPLE... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR INDUCTION.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FUEL SYSTEM.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRICAL SYSTEM.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE MANAGEMENT SYSTEM (EMS) ... .... .... .... .... .... .... .... .... ... .... .... ... ....
EMS ENGINE MANAGEMENT SYSTEM FUNCTIONS... .. ... .. ... .. ... ... .. ... .. ... ... ... ... .. ...
02 DIAGNOSTIC P ROCEDURES
8/11/2019 Sea Doo Shop Manual (2005)
6/314
TABLE
IDLE SPEED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IGNITION TIMING.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY LANYARD SWITCH VERIFICATION.. .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ECM AND MPEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE WIRING HARNESS.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FUEL INJECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THROTTLE BODY .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THROTTLE POSITION SENSOR (TPS).. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IDLE BYPASS VALVE.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CRANKSHAFT POSITION SENSOR (CPS)... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .CAMSHAFT POSITION SENSOR (CAPS)... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MANIFOLD AIR TEMPERATURE SENSOR (MATS) .. ... .. ... .. ... .. .. ... .. ... .. ... ..
COOLANT TEMPERATURE SENSOR (CTS).. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MANIFOLD AIR PRESSURE SENSOR (MAPS) .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXHAUST GAS TEMPERATURE SENSOR (EGTS)... .. ... ... .. ... .. ... ... .. ... .. ... ..
KNOCK SENSOR (KS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OIL PRESSURE SENSOR (OPS) .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOPS VALVE .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OIL SEPARATOR PRESSURE SENSOR (OSPS) ... .. ... ... .. ... ... ... .. ... ... .. ... .. .
TOPS SWITCH.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
05 FUEL SYSTEM01 FUE L TANK AND FUE L PU MP .... .... .... .... .... .... .... .... .... .... ... .... ....
GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSPECTION.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TESTING PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
06 ELECTRICAL SYSTEM01 IG NITION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
QUICK TEST WITH B.U.D.S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VOLTAGE TEST.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IGNITION COIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPARK PLUGS.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IGNITION TIMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02 CHARGI NG SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TESTING PROCEDURE.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RECTIFIER/REGULATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BATTERY
8/11/2019 Sea Doo Shop Manual (2005)
7/314
TABLE OF CONTENTS
STARTER SPECIFICATION ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .04 IN STR UMEN TS AN D A CC ESSO RIES .. ... .... .... .... .... .... .... .... .... .... ... .... .... ... ....
GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . .
COMPONENT DESCRIPTION.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROCEDURES.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
07 PROPULSION01 JET PUM P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . .
JET PUMP INSPECTION ON WATERCRAFT... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PARTS INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PUMP PRESSURIZATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02 DRIVE SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . .REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSPECTION.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LUBRICATION .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
03 REVERSE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSPECTION.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTMENT.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
04 VAR IAB LE T RIM SY ST EM .... .... .... .... .... ... ... ... .... .... ... .... .... .... .... .... .... .... ... .
GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . .
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSPECTION.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTMENT.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
08 STEERING SYSTEM01 STEERIN G SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ALIGNMENT.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02 OFF POWER ASSISTED STEERING SYSTEM (O P A S )
8/11/2019 Sea Doo Shop Manual (2005)
8/314
TABLE
09 HULL/BODY01 ADJU ST ME NT AN D RE PAIR ... .... .... .... .... .... .... .... ... .... .... ... .... ....
GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GLOVE BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE COVER.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SEAT ADJUSTMENT.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STORAGE COMPARTMENT INNER SHELL .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STORAGE COVER SHOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STORAGE COMPARTMENT COVER ADJUSTMENT ... .. ... .. ... .. .. ... .. ... .. ... ..
MIRROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLUSTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DEFLECTOR AND/OR UPPER GRID... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SIDE MOLDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INLET GRATE.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RIDING PLATE.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
JET PUMP SUPPORT.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DRAIN PLUG INSTALLATION ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SEAT COVER REPLACEMENT.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BUMPER REPLACEMENT.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WAKE PYLON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPONSON REPLACEMENT.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPONSON ADAPTOR.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BAILER PICK-UPS INSPECTION ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DECALS REPLACEMENT.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HULL AND BODY REPAIR.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TOOLS AND MATERIALS LIST .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 TECHNICAL SPECIFICATIONS01 GT X, WAKE AN D G TX SC MO DELS .... .... .... .... ... ... ... .... .... ... .... ....
02 GT X L IMITED AND R XT MOD ELS ..... ... .... .... .... .... .... .... .... ... .... ....
03 R XP MODELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 ELECTRICAL CONNECTORS AND WIRING DIAGRAMS01 E LE CTR ICAL CON NE CT OR S ... .... .... .... .... .... .... .... ... .... .... ... .... ....
DEUTSCH CONNECTORS.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PACKARD CONNECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMP CONNECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ECM CONNECTORS.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BATTERY AND STARTER CABLE TERMINALS... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02 WIRIN G DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WIRE COLOR CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WIRE DIGIT CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8/11/2019 Sea Doo Shop Manual (2005)
9/314
SAFETY NOTICE
SAFETY NOTICEThis manual has been prepared as a guide to correctly service and repair 2005 SEA-DOO wdescribe in the model list in the INTRODUCTION.
This edition was primarily published to be used by watercraft mechanical technicians who aremiliar with all service procedures relating to BRP made watercraft. Mechanical technicians shtraining courses given by BRP Training Dept.
Please note that the instructions will apply only if proper hand tools and special service tools
ThisVEHICLE SHOP MANUALuses technical terms which may be slightly different from thein the Parts Catalog.
It is understood that this manual may be translated into another language. In the event of anycy, the English version shall prevail.
The content depicts parts and/or procedures applicable to the particular product at time of wvice and Warranty Bulletins may be published to update the content of this manual. Make sand understand these.
In addition, the sole purpose of the illustrations throughout the manual, is to assist identificageneral configuration of the parts. They are not to be interpreted as technical drawings or exof the parts.
The use of BRP parts is most strongly recommended when considering replacement of any cDealer and/or distributor assistance should be sought in case of doubt.
The engines and the corresponding components identified in this document should not beproduct(s) other than those mentioned in this document.
WARNINGUnless otherwise specified, engine should be turned OFF and cold for all maintenance procedures.
This manual emphasizes particular information denoted by the wording and symbols:
WARNINGIdentifies an instruction which, if not followed, could cause serious personal injury inclsibility of death.
CAUTION:Denotes an instruction which, if not followed, could severely damage vehicnents.
NOTE:Indicates supplementary information needed to fully complete an instruction.
Although the mere reading of such information does not eliminate the hazard, your understaninformation will promote its correct use. Always use common shopsafety practice.
8/11/2019 Sea Doo Shop Manual (2005)
10/314
I
INTRODUCTION
GENERAL INFORMATION
ThisVEHICLE SHOP MANUALcovers the following BRP made SEA-DOO 200should be used in conjunction with the1503 4-TEC ENGINE SHOP MANUAL.
MODEL COLOR ENGINE
GTX Twilight Blue Pearl 1503 Naturally Aspirated
GTX Limited Midnight Black Pearl 1503 Supercharged Intercooled
GTX Supercharged Twilight Blue Pearl 1503 Supercharged
RXP Apple Green 1503 Supercharged Intercooled
RXP Viper Red Metallic 1503 Supercharged Intercooled
RXT Apple Green 1503 Supercharged Intercooled
RXT Viper Red Metallic 1503 Supercharged Intercooled
WAKE Viper Red 1503 Naturally Aspirated
The use of RIGHT (starboard) and LEFT (port) indi-cations in the text, always refers to driving position(when sitting on watercraft).
Besides, in the marine industry, FRONT is calledBOW and REAR is called STERN.
F01L45B
1 2
1. Left (port)2. Right (starboard)
The information and component/system descrip-
This VEHICLE SHOP Mterms which may be diffthePARTS CATALOGS.
When ordering parts alwamodelPARTS CATALOGS
Hull Identification N
The Hull Identification Numdigits:
smr05-002-001_aen
8/11/2019 Sea Doo Shop Manual (2005)
11/314
INTRODUCTION
It is located on footboard at the rear of watercraft.
F08L0QA 1
TYPICAL
1. Hull Identification Number (H.I.N.)
P C
ARRANGEMENT OF THISMANUAL
The manual is divided into many majoryou can see in the main table of contbeginning of the manual.
Several sections are divided in variotions. There is a table of contents at thof many sections.
ABBREVIATIONS USED INTHIS MANUAL
ABBREVIATION DESCRIPTION
4-TEC NA Naturally-Aspirated Engine
ADC Analog to Digital Conversio
AC Alternate Current
APS Air Pressure Sensor
ATS Air Temperature Sensor
B.U.D.S. BRP Utility and Diagnostic
CDI Capacitor Discharge Ignitio
CPS Crankshaft Position Senso
CSI Cooling System Indicator
DC Direct Current
DESS Digitally Encoded Security
DI Direct Injection
E.I.N. Engine Identification Numb
ECM Engine Control Module
ECU Electronic Control Unit
EPA Environmental Protection A
HP Horse Power
LED Light Emitting Diode
IC Intercooler
LED Light Emitting Diode
MAG Magneto
MPEM Multi-Purpose Electronic M
8/11/2019 Sea Doo Shop Manual (2005)
12/314
I
ABBREVIATION DESCRIPTION
RAVE Rotax Adjustable Variable Exhaust
RFI Rotax Fuel Injection
RPM Revolution Per Minute
Sc Supercharger
STD Standard
TBD To Be Determined
TDC Top Dead CenterTPS Throttle Position Sensor
VDC Volt Direct Current
VCK Vehicle Communication Kit
Vdc Volt Direct Current
VTS Variable Trim System
WTS Water Temperature Sensor
ILLUSTRATIONS ANDPROCEDURES
The illustrations show the typical construction ofthe different assemblies and, in all cases, may notreproduce thefull detail or exact shape of the partsshown, however, they represent parts which havethe same or a similar function.
CAUTION:These watercraft are designed withparts dimensioned mostly in the metric sys-tem. However some components may be fromthe imperial system. When replacing fasten-ers, make sure to use only those recommendedby BRP.
Asmany of the procedures in this manual are inter-related, we suggest, that before undertaking anytask, you read and thoroughly understand the en-
tire section or subsection in which the procedureis contained.
A number of procedures throughout the book re-quire the use of special tools. Before undertakingany procedure, be sure that you have on hand allthe tools required, or approved equivalents.
8/11/2019 Sea Doo Shop Manual (2005)
13/314
INTRODUCTION
8/11/2019 Sea Doo Shop Manual (2005)
14/314
I
8/11/2019 Sea Doo Shop Manual (2005)
15/314
INTRODUCTION
ENGINE EMISSIONSINFORMATION
Manufacturer's Responsibility
Beginning with 1999 model year engines, PWCmanufacturers of marine engines must determinethe exhaust emission levels for each engine horse-power family and certify these engines with theUnited States of America Environmental Protec-tion Agency (EPA). An emissions control informa-tion label, showing emission levels and enginespecifications, must be placed on each vehicle atthe time of manufacture.
Dealer Responsibility
When performing service on all 1999 and morerecent Sea-Doo watercrafts that carry an emis-
sions control information label, adjustments mustbe kept within published factory specifications.
Replacement or repair of any emission relatedcomponent must be executed in a manner thatmaintains emission levels within the prescribedcertification standards.
Dealers are not to modify the engine in any man-ner that would alter the horsepower or allow emis-sion levels to exceed their predetermined factoryspecifications.
Exceptions include manufacturer's prescribedchanges, such as altitude adjustments for exam-ple.
Owner Responsibility
The owner/operator is required to have enginemaintenance performed to maintain emission
levels within prescribed certification standards.
The owner/operator is not to, and should not al-low anyone to modify the engine in any mannerthat would alter the horsepower or allow emis-sions levels to exceed their predetermined factoryspecifications.
EPA Emission RegulationsAll new 1999 and more recent Sea-crafts manufactured by BRP are certEPA as conforming to the requiremregulations for the control of air polnew watercraft engines. This certificatingent on certain adjustments being sstandards. For this reason, the factoryfor servicing the product must be stric
and, whenever practicable, returned nal intent of the design.
The responsibilities listed above are gin no way a complete listing of the rulelations pertaining to the EPA requiremhaust emissions for marine productsdetailed information on this subject, yotact the following locations:
VIA U.S. POSTAL SERVICE:Office of Mobile Sources
Engine Programs and Compliance Div
Engine Compliance Programs Group (
401 M St. NW Washington, DC 2046
VIA EXPRESS or COURIER MAIL:
Office of Mobile Sources
Engine Programs and Compliance Div
Engine Compliance Programs Group (
501 3rd St. NW Washington, DC 2000
EPA INTERNET WEB SITE:
http:/www.epa.gov/omswww
SELF-LOCKING FASTENER
PROCEDUREThe following describes the most comcation procedures when working with fasteners.
Use a metal brush or a screwtap to clel th l t (M th l C
8/11/2019 Sea Doo Shop Manual (2005)
16/314
I
LOCTITE APPLICATIONPROCEDURE
The following describes the most common ap-plication procedures when working with Loctiteproducts.
NOTE:Always use proper strength Loctite prod-uct as recommended in thisSHOP MANUAL.
ThreadlockerUncovered Holes (bolts and nuts)
1. Apply here2. Do not apply
Clean threads (bolt and nut) with solvent.
Apply Loctite Primer N (P/N 293 800 041) onthreads and allow to dry.
Choose proper strength Loctite threadlocker.
Fit bolt in the hole.
Apply a few drops of threadlocker at proposedtightened nut engagement area.
Position nut and tighten as required.
Blind Holes
1. On threads2. On threads and at the bottom
Clean threads (bolt and Apply Loctite Primer N
threads (bolt and nut) seconds.
Choose proper strength
Apply several drops alonat the bottom of the ho
Apply several drops on
Tighten as required.Stud in Blind Holes
1 On threads
8/11/2019 Sea Doo Shop Manual (2005)
17/314
INTRODUCTION
Install stud. Install cover, etc.
Apply drops of proper strength Loctite on un-covered threads.
Tighten nuts as required.
Preassembled Parts
A00A3OA
1
2
1. Apply here2. Do not apply
Clean bolts and nuts with solvent.
Assemble components.
Tighten nuts.
Apply drops of proper strength Loctite onbolt/nut contact surfaces.
Avoid touching metal with tip of flask.
NOTE: For preventive maintenance on exist-ing equipment, retighten nuts and apply properstrength Loctite on bolt/nut contact surfaces.
Adjusting Screw
1. Apply here2. Plunger
Adjust screw to proper setting.
Apply drops of proper strength Loclocker on screw/body contact surfa
Avoid touching metal with tip of flas
NOTE:if it is difficult to readjust, heat a soldering iron (232C (450F)).
Stripped Thread Repair
1. Release agent2. Stripped threads3. Form-A-Thread4. Tape5. Cleaned bolt6 Plate
8/11/2019 Sea Doo Shop Manual (2005)
18/314
I
b. Put waxed paper or similar film on the sur-faces.
Twist bolt when inserting it to improve threadconformation.
NOTE:NOT intended for engine stud repairs.
Repair of Small Holes/Fine Threads
Option 1: Enlarge damaged hole, then followSTANDARD THREAD REPAIR procedure.
Option 2: Apply FORM-A-THREAD on the screwand insert in damaged hole.
Permanent Stud Installation (light duty)
Use a stud or thread on desired length.
DO NOT apply release agent on stud.
Do a STANDARD THREAD REPAIR.
Allow to cure for 30 minutes.
Assemble.
Gasket Compound
A00A3SA
21
1 3
1
1. Proper strength Loctite2. Loctite Primer N (P/N 293 800 041) and Gasket Eliminator 518
(P/N 293 800 038) on both sides of gasket3. Loctite Primer N only
Apply GASKET ELIMIN038) on both sides of gplicator.
Place gasket on matingimmediately.
NOTE:If the cover is bolteapply proper strength Lothreads. Tighten.
If holes are sunken, applyon bolt threads.
Tighten as usual.
Mounting on Shaft
Mounting with a Press
1. Bearing2. Proper strength Loctite3. Shaft
Clean shaft external papart.
Apply a strip of proper scircumference at insert
NOTE:Retaining compou
when applied on shaft. DO NOT use anti-seize
product.
No curing period is req
Mounting in Tandem
1 A l t i i
8/11/2019 Sea Doo Shop Manual (2005)
19/314
INTRODUCTION
Case-in ComponentsMetallic Gaskets
1. Proper strength Loctite
Clean inner housing diameter and outer gasketdiameter.
Spray housing and gasket with Loctite Primer N(P/N 293 800 041).
Apply a strip of proper strength Loctite on lead-ing edge of outer metallic gasket diameter.
NOTE:Any Loctite product can be used here. Alow strength liquid is recommended as normalstrength and gap are required.
Install according to standard procedure.
Wipe off surplus. Allow it to cure for 30 minutes.
NOTE:Normally used on worn-out housings toprevent leaking or sliding.
It is generally not necessary to remove gasketcompound applied on outer gasket diameter.
TIGHTENING TORQUES
Tighten fasteners to torque mentioned in explod-ed views and/or text, When they are not specified,refer to following table.
WARNINGT h ti ht i ifi ti
In order to avoid a poor assembliscrews, bolts or nuts in accordancfollowing procedure:
Manually screw all screws, bolts and
Apply the half of the recommended to
CAUTION:Be sure to use the propertorque for the proper strength grade
NOTE: When possible, always apply to
nut.
Torque to the recommended torque
NOTE:Always torque screws, bolts ana criss-cross sequence.
8/11/2019 Sea Doo Shop Manual (2005)
20/314
I
FASTENER GRADE/TORQUEFASTENER
SIZE 5.8Grade 8.8 Grade 10.9Grade
M4 1.5 2 Nm(13 18 lbfin)
2.5 3 Nm(22 27 lbfin)
3.5 4 Nm(31 35 lbfin)
M5 3 3.5 Nm
(27 31 lbfin)4.5 5.5 Nm(40 47 lbfin)
7 8.5 Nm(62 75 lbfin)
M6 6.5 8.5 Nm
(58 75 lbfin)8 12 Nm
(71 106 lbfin)10.5 15 Nm(93 133 lbfin)
M8 15 Nm (11 lbfft) 24.5 Nm (18 lbfft) 31.5 Nm (23 lbfft)
M10 29 Nm (21 lbfft) 48 Nm (35 lbfft) 61 Nm (45 lbfft) M12 52 Nm (38 lbfft) 85 Nm (63 lbfft) 105 Nm (77 lbfft)
M14 85 Nm (63 lbfft) 135 Nm (100 lbfft) 170 Nm (125 lbfft)
8/11/2019 Sea Doo Shop Manual (2005)
21/314
Section 0
Subsection 01 (MAI
MAINTENANCE CHARTThe schedule should be adjusted according to operating conditions and use.
NOTE:The chart gives an equivalence between number of hours and months/yenance operation to whatever time comes first.
IMPORTANT: Watercraft rental operations or intensive use of watercraft, will reof inspection and maintenance.
4-TEC MODELSFIRST 10 HOURS
EVERY 25 HOURS OR 3 MO
EVERY 50 HOURS O
A: ADJUST
C: CLEAN
I: INSPECT
L: LUBRICATE
R: REPLACE
T: PROCEED WITH TASK EVERY 100 H
PART/TASK
GENERAL
Lubrication/corrosion protection T
ENGINE
Engine oil and filter (including cover's O-rings) R R (7)
Support and rubber mount I I
Seals and fasteners I I
Exhaust system fasteners (5) I I
Spark plug (5) R
Supercharger slipping moment (if so equipped) I
Supercharger drive gear, shaft and lock washer (if so equipped) I (10)
(5) Emission-re
(7) Replace for
of use whic
(10) Every 100
engines.
Every 200
intercoole
COOLING SYSTEM
Flushing (exhaust system) T (3)
Hose and fasteners I I
Coolant I R (7)
Coolant expansion tank cap/cooling system pressure test T (4)
(3) Daily flushi
(4) Perform ev
(7) Replace for
of use whic
FUEL SYSTEMThrottle cable I, A, L
Engine management system sensors I I
Fault code reading of engine management system (1) (5) I
Fuel lines, fuel rail, connections, pressure relief valve and fuel system
pressurization (5) I I
(1) In salt wate
(5) Emission-r
8/11/2019 Sea Doo Shop Manual (2005)
22/314
Section 01 MAINTENANCE
Subsection 01 (MAINTENANCE CHART)
4-TEC MODELSFIRST 10 HOURS
EVERY 25 HOURS OR 3 MONTHS
EVERY 50 HOURS OR 6 MONTHS
A: ADJUST
C: CLEAN
I: INSPECT
L: LUBRICATE
R: REPLACE
T: PROCEED WITH TASK EVERY 100 HOURS OR 1 YEAR
PART/TASK LEGEND
ELECTRICAL SYSTEM
Electrical connections and fastening (ignition system, starting system,fuel injectors etc.)
I I
MPEM and ECM connectors I (1)
MPEM mounting brackets/fasteners I
Digitally Encoded Security System and safety lanyard/post I I
Monitoring beeper I I
Battery and fasteners I I
(1) In salt water use.
STEERING SYSTEM
Steering cable I, A, L I, A, L
O .P.A .S . s yst em i nc lu din g fil te r (if so e qu ip ped ) I , A I, A (8) I, A (8) E ve ry 25 ho ur s wh en rid in g i n
PROPULSION SYSTEM
Drive shaft corrosion protection L (9)
Drive shaft protection boot I (2)
Drive shaft/impeller splines (normally aspirated and supercharged
engines) L
Drive shaft/impeller splines (supercharged intercooled engines) L
Sacrificial anode I
Shifter system/cable I, A, L I, A, L
VTS (Variable Trim System) (if so equipped) I, A I, A
Impeller shaft seal, sleeve and O -ring I (6)
Impeller and impeller/wear ring clearance I (2)
Water intake grate I (2)
Ride plate including coolant leak I IDrive shaft/hull sealing system I I
(2) These items have to be initially25 hours. Thereafter, servicin
specified in this chart.
(6) Replace after the vehicle com
of use or 2 years.
(9) Perform at storage period or a
use whichever comes first.
HULL/BODY
Bailer pick-ups, check for obstructions I I
Hull I I
S f
8/11/2019 Sea Doo Shop Manual (2005)
23/314
Section 0
Subsection 02 (PRESEAS
PRESEASON PREPARATIONTO BE PERFORMED BY
PRESEASON PREPARATIONCUSTOMER DEALER
GENERAL
Lubrication and corrosion protection
Spark plugs replacement (1)
ENGINEExhaust system condition and fasteners
Condition of seals and fasteners A
Oil level
COOLING SYSTEM
Coolant level
Hoses and components (3)
FUEL SYSTEM
Fuel injection sensors verification
Inspection of check valves, lines, fasteners andpressurization (2)
Filler neck, fuel tank and fuel cap condition (2)
Fuel tank straps
F
Refill fuel tank
ELECTRICAL SYSTEM
Battery condition/charging and installation
Connection and routing of electric harness (battery,starter, etc.) (2)
Digitally Encoded Security System (DESS) andmonitoring beeper verification
STEERING SYSTEM
Steering system adjustment and inspection (2)
Check O.P.A.S. system condition
8/11/2019 Sea Doo Shop Manual (2005)
24/314
Section 01 MAINTENANCE
Subsection 02 (PRESEASON PREPARATION)
TO BE PERFORMED BYPRESEASON PREPARATIONCUSTOMER DEALER
REFER
PROPULSION SYSTEM
Shifter system condition and cable adjustment Reverse S
Variable Trim System (VTS) condition(if so equipped)
VTS Sys
Propulsion system inspection Jet Pump and D
HULL and BODYInspection of bailer pick-ups Hull/Bo
Ski/wakeboard post and fasteners(if so equipped)
Hull/Bo
(1) Before installing new spark plugs, it is suggested to burn the excess BOMBARDIER LUBE (P/N 2or equivalent by starting the engine using the old spark plugs.
(2) Safety item covered in the annual safety inspection.
(3) If antifreeze was not changed for storage, drain and replace with new antifreeze.
N.A.: Not applicable
8/11/2019 Sea Doo Shop Manual (2005)
25/314
Section 0
Subsection 03 (STOR
STORAGE PROCEDURESSERVICE TOOLS
Description Part Number
flushing connector adaptor ................................................... 295 500 473 .........small hose pincher................................................................ 295 000 076 .........
SERVICE PRODUCTS
Description Part Number
anticorrosion coating ............................................................ 219 700 304 .........Bombardier fuel stabilizer..................................................... 413 408 600 .........
BOMBARDIER LUBE lubricant............................................. 293 600 016 .........
Loctite 243 (blue).................................................................. 293 800 060 .........
PROPULSION SYSTEM
Jet Pump
Verify jet pump grease for water contamination.
Check for the presence of water in cone and bear-ing; if so, replace oil seal and sleeve.
CAUTION: Use only Bombardier jet pumpgrease or equivalent, otherwise componentsservice life could be reduced. Do not mixgrease brands or types.
FUEL SYSTEM
Verify fuel system. Check fuel hoses for leaks.Replace damaged hoses or clamps if necessary.
Bombardier fuel stabilizer (P/N 413 408 600) orequivalent should be added in fuel tank to preventfuel deterioration and fuel system gumming. Fol-low manufacturer's instructions for proper use.
WARFuel is inflammable acertain conditions. Alventilated area. Do not
flames or sparks in thmay be pressurized, sopening. When fuelingel. Do not overfill or toleave watercraft in the increases, fuel expandsAlways wipe off any fwatercraft. Periodically
ENGINE OIL ANDREPLACEMENT
Change engine oil and filTION SYSTEM in ENGINE
8/11/2019 Sea Doo Shop Manual (2005)
26/314
Section 01 MAINTENANCE
Subsection 03 (STORAGE PROCEDURES)
Cooling system flushing should be performedwhen the watercraft is not expected to be usedfurther the same day or when the watercraft isstored for any extended time.
CAUTION:Failure to flush open loop coolingsystem, when necessary, will severely dam-age engine intercooler and/or exhaust system.Make sure engine operates during entire pro-cedure.
WARNINGPerform this operation in a well ventilatedarea. Do not touch any electrical part or jetpump area when engine is running.
Proceed as follows:
Clean jet pump by spraying water in its inlet andoutlet and then apply a coating of BOMBARDIERLUBE lubricant (P/N 293 600 016) or equivalent.
WARNINGAlways remove safety lanyard cap from postto prevent unexpected engine starting beforecleaning the jet pump area. Engine must notbe running for this operation.
Procedure Using Flushing Connectoron Jet Pump Support
All Models
Connect a garden hose to connector located at therear of watercraft on jet pump support. Do notopen water tap yet.
WARNINGWhen operating the engine while the water-craft is out of the water, the heat exchangerin the ride plate may become very hot. Avoidany contact with ride plate as burns may oc-cur.
1. Quick connect adapter2. Flushing connector adapter
TYPICAL
1. Flushing connector
2. Quick connect adapter and flushing connector ad3. Garden hose
To flush the exhaust cooling systemengine then immediately open the wa
WARNINGCertain components in the enginement may be very hot. Direct conta
sult in skin burn. Do not touch anypart or jet pump area when engine i
CAUTION:Never flush a hot enginstart the engine before opening theOpen water tap immediately afterstarted to prevent overheating.
8/11/2019 Sea Doo Shop Manual (2005)
27/314
Section 0
Subsection 03 (STOR
Close the water tap, then stop the engine.CAUTION:Always close the water tap beforestopping the engine.
Disconnect the garden hose.
CAUTION:Remove flushing connector adapterafter operation (if used).
Procedure Using Flushing Connector
in Engine CompartmentGTX 4-TEC Limited Models
This flushing connectorallows to flush the exhaustcooling system directly by the engine compart-ment. The access is easier than the connectoron the jet pump support but requires the use ofa small hose pincher.
Remove seat to gain access.
Install a small hose pincheplied inside vehicle tool kThis prevent water from dcooling system.
This prevents water fromcooling system.
1. Coupler hose2. Small hose pincher
Attach other end of coupleDo not open water tap ye
To flush the exhaust cooligine then immediately op
WARCertain components inment may be very hot
S i MAINTENANCE
8/11/2019 Sea Doo Shop Manual (2005)
28/314
Section 01 MAINTENANCE
Subsection 03 (STORAGE PROCEDURES)
CAUTION: Never run engine without supplyingwater to the exhaust cooling system when wa-tercraft is out of water.
CAUTION: Never run engine longer than 5 min-utes. Drive line seal has no cooling when wa-tercraft is out of water.
Run the engine about 20 seconds at a fast idlebetween 4000 - 5000 RPM.
Ensure water flows out of jet pump while flushing.
Close the water tap, then stop the engine.
CAUTION:Always close the water tap beforestopping the engine.
Unlock and remove coupler hose. Reinstall dustcap over flushing connector.
Remove hose pincher from water outlet hose.
CAUTION:Serious damage to exhaust system
can occur if hose pincher is not removed.
CLOSED LOOP COOLINGSYSTEM (ENGINE)
Antifreeze should be replaced for the storage pe-riod to prevent antifreeze deterioration.
Make sure to perform an antifreeze density test.
For the coolant replacement procedure, refer toCOOLING SYSTEM section.
CAUTION: Improper antifreeze mixture mightallow freezing of the liquid in the cooling sys-tem if vehicle is stored in area where freezingpoint is reached. This would seriously damagethe engine. Failure to replace the antifreezefor storage may allow its degradation thatcould result in poor cooling when engine will
be used.
ENGINE LUBRICATION
Engine must be lubricated to prevent corrosion oninternal parts.
F i f th i i d d t th d
Spray liberally BOMBARDIER LUB(P/N 293 600 016) into the intake po
Crank engine several times while ketle fully depressed (drown engine mtribute lubricant in cylinders, on inand exhaust valves.
Carefully inspect O-rings conditioninstalling fuel injectors. Replace Onew ones if damaged. Lubricate O
injection oil prior to installing. Reinstall the injectors.
Apply Loctite 243 (blue) (P/N 293 8torque the two bolts to 9 Nm (80 hold the fuel rail on.
Make sure there is no leak at injecranking the engine in the upcomin
WARNINGIf a leak is present, immediately stgine. Do not start engine until thepaired.
WARNINGAt preseason preparation, ensure ta fuel pressure test and ensure thleak. Also run engine and check
Refer to FUEL TANK AND FUEL Ption.
THROTTLE BODY LUBRICA
It is recommended to lubricate the thto prevent corrosion on external and inespecially if the craft is used in salt wa
Remove the air intake hose from throt
Open the throttle body valve by pressthe throttle lever and spray BOMBARlubricant (P/N 293 600 016) through body bore to lubricate valve mechan
l th t l t
S ti 0
8/11/2019 Sea Doo Shop Manual (2005)
29/314
Section 0
Subsection 03 (STOR
Let the intercooler drain, then connect the bot-tom hose.
Pour approximately 200 mL (6.76 oz U.S.) ofantifreeze into the intercooler.
Thenpour approximately300mL (10.14 oz U.S.)of antifreeze into the exhaust manifold.
Reconnect the upper hose.
CAUTION: It is highly recommended to pourantifreeze into the intercooler and exhaustmanifold. Failure to do so, may cause severedamage to these components.
CAUTION: Use only undiluted antifreeze (100%concentration). The premixed antifreeze avail-able from BRP is NOT suitable for this par-ticular application. Its concentration will bereduced when mixed with remaining watertrapped in water jackets.
NOTE: When available, it is recommended touse biodegradable antifreeze compatible withinternal combustion aluminum engines. This willcontribute to protect the environment.
NOTE:The engine will not have to run during thisoperation but should have been ran before, to ex-haust as much water as possible, from coolingsystem components.
BATTERYFor battery removal, cleaning and storage, refer toCHARGING SYSTEM.
WATERCRAFT CLEANING
Clean the bilge with hot water and mild detergentor with bilge cleaner. Rinse thoroughly. Lift front
end of watercraft to completely drain bilge. If anyrepairs are needed to body or to the hull, touchup paint and Gelcote repair kit are available. Re-place damaged labels/decals.
Wash the body with soap and water solution (onlyuse mild detergent). Rinse thoroughly with fresh
If the watercraft is to be with an opaque tarpaulin grime from affecting the ptercraft finish as well as plation.
CAUTION:The watercrawater for storage. Nevestored in direct sunlight
ANTICORROSIONWipe offany residual watement.
Spray BOMBARDIER LUB016) over all metallic compartment.
Lubricate the throttle cabLUBE lubricant (P/N 293 6
Apply the anticorrosion coon drive shaft. Refer to D
The seat and the seat extly left opened during storagine compartment condenrosion.
Section 01 MAINTENANCE
8/11/2019 Sea Doo Shop Manual (2005)
30/314
Section 01 MAINTENANCE
Subsection 03 (STORAGE PROCEDURES)
CHECKLISTOPERATION
Verify jet pump grease.
Verify fuel system.
Add Bombardier fuel stabilizer.
Fill up fuel tank.
Change engine oil and filter.
Check engine drain hose(s).
Flush exhaust cooling system.
Replace antifreeze. Check solutionconcentration in the cooling system (in coolregions).
Lubricate the engine.
Lubricate throttle body.
Add antifreeze into intercooler and exhaustmanifold (where temperatures are belowfreezing).
Remove, clean and store the battery.
Clean the bilge.
Wash the body.
Spray BOMBARDIER LUBE lubricant (P/N 293600 016) over all metallic components in enginecompartment and in throttle cable.
Apply the anticorrosion coating (P/N 219 700304) on drive shaft.
Partially lift the seat and the seat extension.
Section 0
8/11/2019 Sea Doo Shop Manual (2005)
31/314
Section 0
Subsection 04 (SPE
SPECIAL PROCEDURESSERVICE TOOLS
Description Part Number
large hose pincher................................................................ 529 032 500 .........oil pump cover fitting............................................................ 293 710 037 .........pump ....................................................................................
529 035 880 .........
SERVICE PRODUCTS
Description Part Number
Loctite 243 (blue).................................................................. 293 800 060 .........
pulley flange cleaner............................................................. 413 711 809 .........
TOWING THE WATERCRAFTIN WATER
Special precautions should be taken when towinga Sea-Doo watercraft in water.
Maximum recommended towing speed is24 km/h (15 MPH).
When towing your watercraft in water, pinch thewater supply hose from the jet pump housing tothe engine with a large hose pincher (P/N 529 032500).
Snugly install the hose pinply hose as shown in the
NOTE: Pinch the hose wequipped).
Section 01 MAINTENANCE
8/11/2019 Sea Doo Shop Manual (2005)
32/314
Section 01 MAINTENANCE
Subsection 04 (SPECIAL PROCEDURES)
TYPICAL
1. Hose pincher
CAUTION: When finished towing the wa-tercraft, the hose pincher must be removedbefore operating it.
SUBMERGED WATERCRAFT
Drain bilge if water is present.
If it was submerged in salt water, spray bilge andall components with fresh water using a gardenhose to stop the salt corroding effect.
Engine
Refer to WATER-FLOODED ENGINE to validate ifi i i
Throttle Body
Throttle body should be lubricated corrosion if watercraft was submergeSTORAGE for procedure.
WATER-FLOODED ENGINE
If engine is water-flooded, it must bwithin a few hours after the event. Ot
gine will have to be overhauled.CAUTION: A water-flooded engineproperly lubricated, operated thenagain, otherwise parts will be serioaged.
Check fuel reservoir for water contamnecessary, siphon and refill with fresh
To limit damages to the engine, perfo
lowing procedure as soon as possibleDrain bilge if water is present.
If it was submerged in salt water, spraall components with fresh water usinhose to stop the salt corroding effect.
CAUTION:Never try to crank or stgine. Water trapped in the intakewould enter the combustion chambthe intake valves and may cause dthe engine.
Whenever the engine is stopped, allclose thus preventing water from beinin the engine.
If water is suspected to be in the intaexhaust system, it must be drained as
Remove the intake manifold and drasuck out the water from the intake vRefer to1503 4-TEC ENGINE SHOP M
Remove the water from oil/air separathose.
Remove the exhaust pipe and drain it. remove the mufflers to drain them or
Section 0
8/11/2019 Sea Doo Shop Manual (2005)
33/314
Section 0
Subsection 04 (SPE
SuperchargerSupercharged 4-TEC Engines
If there was water in the oil or in the intake mani-fold, it is recommended to take the superchargerapart, dry all the components, replace the slipclutch needle bearings and shaft ball bearings.Refer to1503 4-TEC ENGINE SHOP MANUAL.
Oil Change Procedure
(water-contaminated oil) Using the pump (P/N 529 035 880), siphon oil
from reservoir through dipstick hole.
CAUTION:Never crank or start engine whensiphon tube is in dipstick hole. Never start en-gine when there is no oil in engine.
Remove the pump from the dipstick hole.
While in drowned engine mode, crank the en-
gine for 5 seconds. Remove the oil filter cap and the oil filter.
Again, siphon oil from the reservoir.
Put a rag under the scavenge oil pump cover.
Remove the scavenge oil pump cover drain plugand install the oil pump cover fitting (P/N 293710 037).
1. Scavenge oil pump cover drain
Connect the pump (P/
fitting. The front of the engine
proximately 15 degreesof the oil. Raise the realy. Siphon the oil from
Level the engine.
Remove thepump andt243 (blue) (P/N 293 80drain plug.
NOTE:If spillage occurs, the pulley flange cleaner (vent oil stains.
Install a new oil filter acap.
Fill up the reservoir wit
Boil out the remaining w
Recommended procCEDURE IN A TESTTRAILER WITH WAT
Optional procedureDURE CONNECTED
Refer to instructions belo
Section 01 MAINTENANCE
8/11/2019 Sea Doo Shop Manual (2005)
34/314
Subsection 04 (SPECIAL PROCEDURES)
WARNINGMake sure to safely secure the watercraft.
With the engine still running at 3500 RPM, in-stall a hose pincher to the coolant line going tothe oil cooler.
WARNINGCertain components in the engine compart-ment may be very hot. Direct contact may re-sult in skin burn. Do not touch any electricalparts or jet pump area when engine is run-ning.
1. Oil cooler coolant inlet hose
Continue to run the engine at 3500 RPM for 15more minutes (20 minutes total run time).
Shut the engine off.
Remove the hose pincher on the coolant line
going to the oil cooler.CAUTION:Hose pincher must be removed pri-or to operating the watercraft. Failure to dothis will result in damage to the engine.
Change the oil and filter again.
Procedure is now completed.
CAUTION: Never run engine withouwater to the exhaust cooling systemtercraft is out of water.
Run the engine for 5 minutes at 30
With the engine still running at 300stall a hose pincher to the coolant lithe oil cooler.
WARNING
Certain components in the enginement may be very hot. Direct contasult in skin burn. Do not touch anyparts or jet pump area when engining.
1. Oil cooler coolant inlet hose
Continue to run the engine at 3000 more minutes (20 minutes total run
Shut off the engine.
Remove the hose pincher on the c
going to the oil cooler.CAUTION:Hose pincher must be reor to operating the watercraft. Fathis will result in damage to the eng
Change the oil and filter again.
Move rearward the ring seal carrier
Section 02 TR
8/11/2019 Sea Doo Shop Manual (2005)
35/314
Subsection 01 (TROUBLE
TROUBLESHOOTING CHARTThe following is provided to help in diagnosing the probable source of troubleshould not be assumed to show all causes for all problems.
NOTE:On fuel injection models, always check for fault codes. If a fault code fault code and recheck operating conditions. Refer to DIAGNOSTIC PROCEDAGEMENT section.
ENGINE WILL NOT START
OTHER OBSERVATION POSSIBLE CAUSE R
Wrong safety lanyard Use one that has
DESS operation non functional If 2 short beeps installing safety lMANAGEMENT
Safety lanyard switch faulty or
disconnected or harness damaged
Replace
Burnt fuse: battery, starting system.Also fuel pump
Check wiring the
Starting system fuse keeps on burning Check wiring, stand MPEM
Discharged or disconnected battery Check/recharge
Defective or disconnected start/stopswitch
Check, refer to S
Battery connections Check/clean/tigh
Poor/bad or corroded ground contacts(engine, starter etc.)
Check/clean/repa
Water/fuel hydro-lock Check, refer to M
Starter malfunction Check, refer to E
Starter solenoid Check, refer to E
Obstructed starter drive gear assembly Check/repair, refHOUSING/MAG4-TEC ENGINE
Seized or obstructed engine Check/repair, refENGINE SHOP
Engine does not turn over
Section 02 TROUBLESHOOTING
8/11/2019 Sea Doo Shop Manual (2005)
36/314
Subsection 01 (TROUBLESHOOTING CHART)
OTHER OBSERVATION POSSIBLE CAUSE REMEDYLoose battery cable connections Check/clean/tighten
Discharged/weak battery Check/charge/replace
Restriction in jet pump Check/clean pump
Partial seizure in jet pump Inspect, refer to PROPULSION
Partial engine hydro-lock Check, refer to MAINTENANC
Partial engine seizure Check compression, refer to t4-TEC ENGINE SHOP MAN
Worn starter Check, refer to ELECTRICAL S
Timing chain not guided by chain guide ) Check, refer to the1503 4-TESHOP MANUAL
Oil is too thick. Change oil vis
Engine turns slowly
Outside temperature too low
Battery capacity is not sufficietemperature
Faulty component in the fuel injectionsystem
Check for fault codes. Refer DIAGNOSTIC PROCEDURES MANAGEMENT
Engine drowned mode is active Release throttle lever
Low battery voltage Recharge or replace battery
Check fuel pump pressure out
Check fuel pump fuse
Low or no fuel pressure
Check wiring harness
Check fuel injector operation. necessary
Fuel injectors not working
Check output signal from MPE
No spark at the spark plug Check spark plugs condition aas necessary
Check ignition system and repDefective MPEM or ECM
Replace MPEM or ECM (as ap
Defective CPS Check operation of CPS and rnecessary
Wat ta i at d f l Ch k/ i h d fill
Engine turns over
Section 02 TR
8/11/2019 Sea Doo Shop Manual (2005)
37/314
Subsection 01 (TROUBLE
OTHER OBSERVATION POSSIBLE CAUSE R
Defective encoder/trigger wheel Check, refer to E
Incorrectly aligned flywheel and triggerwheel
Properly positionwheel, refer to thSHOP MANUA
Insufficient engine compression Replace defectiv
Engine turns over (cont'd)
Idle bypass valve stuck or notfunctioning
Check, refer to E
Spark plug faulty, fouled or worn out Check spark plug
Ignition Check, refer to E
No spark at spark plugs
Faulty ECM Replace ECM
ENGINE HARD TO START
OTHER OBSERVATION POSSIBLE CAUSE R
Defective idle bypass valve Refer to ENGINE
Wrong TPS zero setting Refer to ENGINE
Throttle cable adjustment Refer to ENGINE
Temperature too low for availablebattery capacity
Battery capacity temperature
Air lock in fuel rail Refer to ENGINE
Water in intake system (defective MAPsensor)
Check and remoSPECIAL PROCE
Water in fuel reservoir or contaminatedfuel
Flush reservoir a
Check cylinder c
Check for cylinde
Mechanical engine failure
Check starting sy
Spark plug faulty, fouled or worn out Check spark plug
Check fuel pumpFUEL TANK AND
Low fuel pressure
Check fuel press
Section 02 TROUBLESHOOTING
S b ti 01 (TROUBLESHOOTING CHART)
8/11/2019 Sea Doo Shop Manual (2005)
38/314
Subsection 01 (TROUBLESHOOTING CHART)
ENGINE STARTS BUT RUNS ONLY AT IDLE SPEED
OTHER OBSERVATION POSSIBLE CAUSE REMEDY
The system is in limp home mode Refer to ENGINE MANAGEMcheck the fault codes
Broken or loose throttle cable Change/readjust
ENGINE MISFIRES, RUNS IRREGULARLY
OTHER OBSERVATION POSSIBLE CAUSE REMEDY
Fouled, defective, worn spark plugs Check/verify heat range/gap/re
Faulty ECM or MPEM Check, refer to ENGINE MANA
Defective trigger wheel/CPS Check, refer to ENGINE MANA
Bad ignition coil wiring Check wiring condition and pgrounding of ignition coil
Faulty ignition coil, or bad connector Check coil. Refer to ENGINEMANAGEMENT or ELECTRICSYSTEM
Weak spark
Poor engine ground Check/clean/repair
Low fuel pressure Check pump, regulator, injectopinchers or if filter is plugged.if necessary
Stale or water fouled fuel Check/siphon and refill
Fuel filter dirty or restricted Check/clean/replace
Clogged fuel injectors Remove and clean fuel injecto
Lean fuel mixtureDry spark plug (exceptwhen water fouled)
Defective sensor or ECM Check faulty codes in ECM meto ENGINE MANAGEMENT
Flame arrester dirty or restricted Check/replace
Faulty fuel injector(s) Remove and replace fuel injec
to ENGINE MANAGEMENT
Defective sensor or ECM Check fault codes. Refer to EMANAGEMENT
Fuel pressure fluctuating Inspect fuel pressure regulatoFUEL SYSTEM
Rich fuel mixtureFouled spark plug
Section 02 TR
Subsection 01 (TROUBLE
8/11/2019 Sea Doo Shop Manual (2005)
39/314
Subsection 01 (TROUBLE
OTHER OBSERVATION POSSIBLE CAUSE R
Check spark plug condition, check faultcodes, check fuel pressure.
Check, refer to IENGINE MANAGhas been performsure injector wiremixed. Refer tofor wire colors a
Starts, but runs poorly
Bent or missing tooth on trigger wheel Check, refer to E
Injector wiring reversed Refer to the WIRAlso fuel injectionmisinjecting
Damaged fuel injector Check, refer to E
ENGINE CONTINUALLY BACKFIRES
OTHER OBSERVATION POSSIBLE CAUSE R
Weak spark Fouled, defective spark plugs Clean/replace
Spark plugs Ignition coil wiring reversed Refer to WIRING
Incorrect setting Check/reset, refeSYSTEMIgnition timing
Defective trigger wheel/CPS Check, refer to E
Engine Intake or exhaust valve(s) leak Pressure check e
4-TEC ENGINE
ENGINE DETONATION OR PINGING
OTHER OBSERVATION POSSIBLE CAUSE R
Ignition Spark plug heat range too high Check/change to
Engine overheats and exhaust overheats Check, see ENGsection
Fuel octane too low of poor fuel quality Use good quality
Knock sensor disconnected or faulty Check, refer to E
Bad knock sensor connection Check, refer to E
Engine/exhaust hightemperature
Bad ECM connection Check, refer to E
Section 02 TROUBLESHOOTING
Subsection 01 (TROUBLESHOOTING CHART)
8/11/2019 Sea Doo Shop Manual (2005)
40/314
Subsection 01 (TROUBLESHOOTING CHART)
ENGINE LACKS ACCELERATION OR POWER
OTHER OBSERVATION POSSIBLE CAUSE REMEDY
Weak spark Check/replace, refer to IGNITSYSTEM
Throttle does not open fully Check/readjust, refer to ENGIMANAGEMENT
Low compression Check/repair, refer to the150
ENGINE SHOP MANUALWater in fuel Check/siphon/replace
Impeller leading edge damaged Check/replace, refer to PROPUSYSTEM
Too much engine oil Siphon or adjust level. Refer LUBRICATION SYSTEM
Poor fuel quality Siphon then refill with fresh fu
Clogged fuel injectors Remove and clean fuel injecto
Low fuel pressure Check fuel line and fuel pump
Incorrect throttle position sensor (TPS)adjustment
Check and adjust TPS, refer toMANAGEMENT
Improper timing chain alignment Refer to CYLINDER HEAD in t4-TEC ENGINE SHOP MAN
Defective supercharger Check/repair, refer to the150
ENGINE SHOP MANUAL
Overheated engine See ENGINE OVERHEATS in t
Engine revs lower thanits maximum operationalRPM
Limp home mode activated Refer to ENGINE MANAGEME
ENGINE STOPS RUNNING
OTHER OBSERVATION POSSIBLE CAUSE REMEDY
Contaminated or inappropriate fuel Syphon reservoir and refill witEngine stalls at idle
Air in fuel rail Refill fuel tank
Engine running out of fuel Check fuel delivery system forEngine start but stops
Section 02 TR
Subsection 01 (TROUBLE
8/11/2019 Sea Doo Shop Manual (2005)
41/314
Subsection 01 (TROUBLE
ENGINE CANNOT REACH MAXIMUM RPM
OTHER OBSERVATION POSSIBLE CAUSE R
Low fuel pressure Check fuel pump
Jet pump related problem Check propulsionJET PUMP
Limp home mode activated Refer to ENGINE
Exhaust system blockage/muffler
damage
Check and repair
Exhaust gases in bilge (leak) Check exhaust s
Defective supercharger Check/repair, refENGINE SHOP
Battery voltage is too low Check/repair, refSYSTEM
ENGINE RUNS TOO FAST (VEHICLE CANNOT REACH IT
OTHER OBSERVATION POSSIBLE CAUSE R
Faulty rev limiter Check, refer to E
Improper impeller pitch (too low) Check/replace, rSYSTEMEngine RPM too high
Damaged impeller Replace impeller
SYSTEMDamaged leading or trailing edge ofimpeller
Check/replaceNOTE:Leading eto poor performaedge damage coperformance and
Jet pump cavitation
Sealing of ride plate, jet pump support orjet pump
Check/reseal, rePROPULSION SY
Section 02 TROUBLESHOOTING
Subsection 01 (TROUBLESHOOTING CHART)
8/11/2019 Sea Doo Shop Manual (2005)
42/314
Subsection 01 (TROUBLESHOOTING CHART)
ENGINE OVERHEATS
OTHER OBSERVATION POSSIBLE CAUSE REMEDY
Coolant level low Refill/check for leaks
Coolant leaking out of weep hole(PTO housing)
Replace seal
Hoses or clamps missing/defective Repair/replace
Cylinder head gasket leaks
(white exhaust gas)
Replace cylinder head gasket
Thermostat failure Replace
Coolant pump failure Replace
Coolant level too low
Internal passage blockage Inspect and clean
Temperature sensor defective Check/replace. Refer to ENGMANAGEMENT
Worn water pump impeller Check/replaceCooling system restriction Check/flush, refer to MAINTE
Damaged ride plate or hoses Check, refer to COOLING SYSHULL/BODY
Monitoring beepersounds continuously
Thermostat defective Check/replace
ENGINE SMOKE IN THE EXHAUST
OTHER OBSERVATION POSSIBLE CAUSE REMEDY
Coolant leak Check/repair. Refer to COOLSYSTEM
Intercooler leak(if so equipped)
Check/repair. Refer to the15ENGINE SHOP MANUAL
Damaged cylinder head gasket Check/replace cylinder head g
Water ingestion Inspect intake manifold for winfiltration
White smoke
Valve guide seals Check/replace valve guide seato CYLINDER HEAD in the15ENGINE SHOP MANUAL
Oil l l t hi h Si h f il
Section 02 TR
Subsection 01 (TROUBLE
8/11/2019 Sea Doo Shop Manual (2005)
43/314
(
LOW OR NO ENGINE OIL PRESSURE
OTHER OBSERVATION POSSIBLE CAUSE
Oil level too low Refill. See TECspecifications
Leaking gasket Replace
Oil leaking out of weep hole (PTO housing) Replace oil seal
Oil pressure sensor defective Check/replace
Oil pump malfunctioning Clean rotor and
Oil regulator valve sticks open, or springload too small
Clean/replace
Heavy wear on plain bearings Replace
ENGINE OIL CONTAMINATION (MILKY)
OTHER OBSERVATION POSSIBLE CAUSE
Oil seal and rotary seal on coolant pumpshaft leaking
Replace both seHOUSING in theSHOP MANUAL
Cylinder head gasket leaking Replace gasket.4-TEC ENGINEChange oil
Loose screws on cylinder head, PTOhousing or oil separator Retorque. Chan
Oil contamination due to metal or plasticparticles
Replace possiblChange oil
Water and oil mixtureleaking out of leak
indicator hole (PTOhousing)
Water ingestion (intake manifold, TOPSvalve, dipstick)
Refer to MAINT
The same causes as above apply. However, look at the folloWater and oil mixturewithout leaking out at
leak indicator hole(PTO housing)
Leak indicator hole plugged Check/clean lea
Section 02 TROUBLESHOOTING
Subsection 01 (TROUBLESHOOTING CHART)
8/11/2019 Sea Doo Shop Manual (2005)
44/314
UNUSUAL ENGINE NOISE AND/OR VIBRATION
OTHER OBSERVATION POSSIBLE CAUSE REMEDY
Worn chain tensioner Replace
Worn chain guide Replace
Stretched chain and/or worn out sprockets Replace chain and sprockets
Sprocket screws got loose Retorque
Hydraulic element inside rocker arm(s)is worn out (valve adjustment) or lifterdamaged
Replace faulty rocker arm(s) a
Rocker arm screws not tightened Retorque
Heavy wear on crankshaft and/or balancershaft bearings
Replace
Crankshaft and balancer shaft not aligned Check marks and readjust sha
Heavy wear on thrust washers, or thrustwashers missing
Check/replace
Defective supercharger (if so equipped) Check/repair, refer to the150ENGINE SHOP MANUAL
Missing/defective air intake hose Check/replace air intake hose refer to AIR INTAKE SYSTEM
INAPPROPRIATE SPEEDOMETER READING
OTHER OBSERVATION POSSIBLE CAUSE REMEDY
Faulty speed sensor or related circuits. Refer to INSTRUMENTS ANACCESSORIES
MPEM was replaced and speedometercalibration data were not transferred tonew MPEM.
Install latest B.U.D.S version in BOSSWeb then connect towith VCK and it will automatupdate MPEM. Refer to ENG
MANAGEMENT
ABNORMAL NOISE FROM PROPULSION SYSTEM
OTHER OBSERVATION POSSIBLE CAUSE REMEDY
Section 02 TR
Subsection 01 (TROUBLE
8/11/2019 Sea Doo Shop Manual (2005)
45/314
NOTE:Prior to replacing an ECM or MPEM, refer to the appropriate ECM/MPEM
replacement in the ENGINE MANAGEMENT section and read carefully the testan ECM/MPEM that could otherwise be good.
Section 03
Subsection 01 (AI
8/11/2019 Sea Doo Shop Manual (2005)
46/314
AIR INTAKE SYSTEMSERVICE TOOLS
Description Part Number
hook tool............................................................................... 529 035 989 .........
Section 03 ENGINE SYSTEM
Subsection 01 (AIR INTAKE SYSTEM)
8/11/2019 Sea Doo Shop Manual (2005)
47/314
4-TEC Naturally Aspirated Engine
Section 03
Subsection 01 (AI
8/11/2019 Sea Doo Shop Manual (2005)
48/314
4-TEC Supercharged and Supercharged Intercooled Engines
Section 03 ENGINE SYSTEM
Subsection 01 (AIR INTAKE SYSTEM)
8/11/2019 Sea Doo Shop Manual (2005)
49/314
INSPECTION
Check for water in air silencerno. 1. If so, replacecheck valvesno. 2. Check collar tightness. En-sure there is no water trapped in tubeno. 3(if soequipped).
Inspect silencer, tube and hose condition. Re-place any damaged part.
REMOVAL
From storage compartment, remove/disconnect:
hoseno. 4.
front access door (if so equipped)
rectifier/voltage regulator
wiring harness from air silencer
fuel tank straps (refer to FUEL SYShook tool (P/N 529 035 989).
Pull air silencer out.
Section 03
Subsection 01 (AI
8/11/2019 Sea Doo Shop Manual (2005)
50/314
1. Lift lock tab
coolant expansion tank
Step 1: Push tab (each side) to releaseStep 2: Pull tank out
vent tube support
1. Vent tube support2. Remove retaining screws3. Pay attention to nuts undernea
tube from air intake hosPull tube out.
INSTALLATION
Reverse removal operatiotion to the following.
Section 03
Subsection 02 (LUB
8/11/2019 Sea Doo Shop Manual (2005)
51/314
LUBRICATION SYSTEMSERVICE TOOLS
Description Part Number
suction pump........................................................................ 529 035 880 .........
SERVICE PRODUCTS
Description Part Number
pulley flange cleaner............................................................. 413 711 809 .........
GENERALPrior to changing the oil, ensure vehicle is on alevel surface.
Oil and oil filter must be replaced at the sametime. Oil change and oil filter replacement shouldbe done with a warm engine.
WARNING
The engine oil can be very hot. Wait until en-gine oil is warm.
Dispose oil and filter as per your local environmen-tal regulations.
OIL LEVEL VERIFICATION
CAUTION:Check level frequently and refill if
necessary. Do not overfill - it would make theengine smoke and reduce its power. Operatingthe engine with an improper level may severelydamage engine. Wipe off any spillage.
Section 03 ENGINE SYSTEM
Subsection 02 (LUBRICATION SYSTEM)
8/11/2019 Sea Doo Shop Manual (2005)
52/314
Check the oil level as follows:
NOTE: It is of the utmost importance to follow thisprocedure in order to obtain an accurate reading ofthe engine oil level.
Watercraft must be level. Check oil level eitherwith watercraft in water or out of water. Engineshould bewarm.
CAUTION: Never run engine without supplyingwater to the exhaust cooling system when wa-
tercraft is out of water. If out of water, raise trailer tongue and block in
position when bumper rail is level. Link a gar-den hose to the hose adapter. Refer to STOR-AGE PROCEDURES in MAINTENANCE sectionand follow the procedures.
CAUTION:Failure to flush exhaust cooling sys-tem, when watercraft is out of water, may se-verely damage engine and/or exhaust system.
Warm-up engine then let idle for 30 secondsbefore stopping.
Stop engine.
Wait at least 30 seconds then pull dipstick outand wipe clean.
WARNINGEngine oil may be hot. Certain components
in the engine compartment may be very hot.Direct contact may result in skin burn.
CAUTION: Never run engine longer than 5 min-utes. Drive line seal has no cooling when wa-tercraft is out of water.
Reinstall dipstick, push in completely.