seawing Room submisiion

NAME OF THE SEAM: SUPER IMPOSED SEAM

Introduction : Super-Imposed seam is the commonest construction seam on garments. The simplest seam type within the class is formed by superimposing the edge of one piece of material on another. A variety of stitch types can be used on this type of seam.

Explanation for making superimposed seam:

Pattern Equipments Machine Sewing Fabrics

Block:2pieces Scissors, Steam iron, Pins, Ruler, Measurement Tape, Tailor’s chalk.

Singer Domestic Sewing M/CNeedle Size: 16Max Stitch per inch:16

Stitch per inch:10Sewing thread: Cotton

poplinSize: 6×6,6×6

Diagram of Superimposed seam:

(a) (b) Superimposed seam Working Processes:

First work: Took two pieces of fabric both are same in size. Second work: Laving 1cm from end & stitch along straight to them.

Uses: Both of fabrics joining the fabrics and for neatening the edge of for achieving both simultaneously.

NAME OF THE SEAM: Lapped seam

Introduction: The simplest seam type in this class is formed by lapping two pieces of fabrics.

Diagram of Lapped seam:

(a) (b) Lapped seamExplanation of Lapped seam:





poplinSize:6×6,6×6

Working Processes:

First work: Take 2 pieces fabrics.Second work: Take the fabrics (a) keep the fabric (a) on the top of (b) then 1cm seam allowance and stitch a striate line.

Uses: Where it is used commonly used is in the joining of panel in sails where a strong seam is achieved by using two of three rows.

NAME OF THE SEAM: Lap felled

Introduction: Much more common on long seams on garments such as jeans and shirts is the so- called lap-felled seam.

Diagram of Lap felled seam

Explanation for making Lap felled-1 seam:





PoplinColor: OrangeSize:6×6,6×6

Working Processes:

First work: Keep two pieces of fabric;Second work: Jointed two pieces of fabric by superimposed than stitch.

Uses: Garments such as jeans and shirts.

NAME OF THE SEAM: BOUND SEAM

Introduction: A folding device turns of the edge under and warps the strip over the edge of the main fabric. Bias cut strip would normally be used, unless the fabric had an element of stretch.

Diagram of Bound seam:

(a) (b) C Bound seam

Explanation for making Bound seam:


Fabric:2piecesRibon: 1 pic.

Scissors, Steam iron, Pins, Ruler, Measurement Tape, Tailor’s chalk.



poplin

Working Processes:Cut 2pieces of fabric and took a ribbon.Then joint it by roving and gave top stitch.

Uses : Children wear.

NAME OF THE SEAM: FRENCH SEAM

Introduction: A similar, and in many cases an equally acceptable seam, could be constructed using a folding device and a multi-needle machine.

Diagram of French seam:

Explanation for making French seam:





poplinSize: 6×6,6×6

Working Processes:First work: Take two pieces of fabrics, o.5cm seam allowance then stitch the fabric a straight line.Second work: Fold the fabric and 1cm seam allowance the stitch the fabric a straight line. Uses: Collar, belt of pants etc.

NAME OF THE SEAM: GATHER SEAM

Introduction : It is a method of fitting of fabric into a small space, which is good on very bulky fabrics. It also gives a decorative effect.

Diagram of Gather seam:

Diagram for making Gather seam:





poplin

Working Processes:First work: Keep two pieces fabric 1part is 7x12inch and another part is 6x2inch.Second work: Keep the first part fabric, and then make a normal stitch.Third work: Now tension the thread and make a gather used by hand.Forth work: Fold another part of fabric and join by stitch.Fifth work: Remove the false stitch.

Uses: Skirts, ladies wear.

NAME OF THE SEAM: NECKlINE WITH FACHING

Introduction: The neck seams of the facings and interfacings are sewn separately. The neck line seam allowance will extend all around. Stitch the interfacing into place.

Diagram of U- shaped neck facing seam:

Explanation for making U- shaped neck facing seam:





poplin

Working Processes:

First work: keep two pieces fabric. Second work: We have to fabric frays, cut .4 inch of the interfacing at the outside edge, turn upper fabric back and sewing.

Uses: Collar, Children dress.

NAME OF THE POCKET: PATCH POCKTE

Introduction : It is one kind of pocket. It is look like an English letter U in this cases it is called U shaped pocket.

Diagram of U- shaped pocket seam:

Explanation for making U- shaped pocket seam:





poplin

Working Processes:

First work: Keep the pocket 1cm fold on the top of the pocket and stitch a line.Second: Keep 1cm around the pocket, with 1cm give the pocket U-shape. Fold the extra cloth from the side.Third work: Then press the pocket smooth.Forth work: Keep the pocket on the bass in middle point.Fifth work: Stitch the pocket in border line.

Uses: Shirt, Baby Frock.

NAME OF THE POCKET: RECTANGULAR PATCH POCKTE

Introduction: There are many types of pocket, it is one of them. It is a very used seam.

Diagram of Applied pocket seam:

Explanation for making Plain pocket seam:





Poplin

Working Processes:

First work: Keep the pocket 1cm fold on the top of the pocket and stitch a line.Second: Keep 1cm around the pocket, with 1cm give the pocket U-shape. Fold the extra cloth from the side.Third work: Then press the pocket smooth.Forth work: Keep the pocket on the bass in middle point.Fifth work: Stitch the pocket in border line.

Uses : Shirt, Pant (Back side).

NAME OF THE PLEAT: BOX PLATE

Introduction : There are three types of flat pleats: box pleat is one of them. Box can fit the box pleated skirt another way, but it’s time-consuming.

Diagram of Box pleat seam:

(a) (b)





poplin

Explanation for making Box pleat seam:

Working Processes:

First work: Keep 2 pieces fabric, (a) pieces is 7x6’’ and another piece (b) is 2.5cm.Second work: First time we have to fold the piece (a), them1.4cm seam allowance and 1.5cm stitch.Third work: Make a box plate used by Iron, and then stitch the fabric the fabric a straight line on top side.Forth work: Fold another part and join the part with the first part used by stitch.Fifth work: Again fold another part (b) and top stitch.

Uses : Shirt, Box pleated skirt.

NAME OF THE PLEAT: INVERTED PLATE

Introduction: There are three types of flat pleats; box pleat, inverted pleats, and side pleats. All other fancy pleating is a combination of types. Pleats are always folded. Diagram of Inverted pleat seam:

(A) (B)

Explanation for making Inverted pleat seam:





Poplin

Working Processes :

First work: Keep 2 pieces fabric, (a) pieces is 7x6’’ and another piece (b) is 2.5cm.Second work: First time we have to fold the piece (a), them1.4cm seam allowance and 1.5cm stitch.Third work: Make a box plate used by Iron, and then stitch the fabric the fabric a straight line on top side.Forth work: Fold another part and join the part with the first part used by stitch.Fifth work: Again fold another part (b) and top stitch.

Uses: Shirt, Inverter pleated skirt.

NAME OF THE SEAM: PIPED SEAM

Introduction: A piping seam with an additional component would be one that contained an inserted and piping.

Diagram of Piped seam:

(a) (b) (c)

Explanation for making Piped seam:





Poplin

Working Processes:

First work: Keep 3 pieces of fabrics. Then small piece (c) has to fold.Second work: Folding fabric has to keep on (a) and (b) side of these fabrics.Third work: Now we have to straight sewing.

Uses: Hemming purposes.

NAME OF THE SEAM: PIPING

Introduction: A folding device turns of the edge under and warps the strip over the edge of the main fabric. Bias cut strip would normally be used, unless the fabric had an element of stretch.

Diagram of piping seam:

(a) (b) Piping seam

Explanation for making Piping seam:





Popling

Working Processes:

First work: Keep two pieces of fabric one is 7x3cm (a) and another is 7X9 (b) cm.Second work:

Uses: Children wear.

NAME OF THE SEAM: DART

Introduction: It is a method of fitting the body into a small space, which is very need for body. It also gives a decorative effect.

Diagram of Dart seam:

(a) (b)

Explanation for making Dart seam:


Block:1piece Scissors, Steam iron, Pins, Ruler, Measurement Tape, Tailor’s chalk.



Poplin

Working Processes:

First work: Take the measurement of dart.Second work: Fold the dart.Third work: Now join two points of dart.Forth work: After joining its make a triangular shape.Fifth work: At the opposite side it takes a shape.

Uses: In any kinds of ladies dress.

NAME OF THE SEAM: WELTED SEAM

Introduction: The type of rose topstitch seam often used down shirt panels is also technically a lapped seam. But its little contraction is different in this case it is called a welted or a raised and welted seam.

Diagram of welted seam:

Explanation for making welted seam:





Poplin

Working Processes:

First work: Keep two pieces fabrics.Second work: Joined two pieces of fabric by over lapping stitch & than superimposed & stitch.

Uses: In side leg seam.

A B

NAME OF THE SEAM: CONTINUOUS STRIP OPENING

Diagram Continuous step opening :

Explanation for making Continuous strip opening :





Poplin

Working Process :

Step 1: Keep the V-neck facing on the base

Step 2: Keep ½ cm seam allowance of the outer V-line, and then stitch V-direction.

Step 3: Move the facing on the opposite side. Press it smoothly.

Step 4: give the top stitch in borderline of V-neck facing.

Uses: *Kameez, Fotua, T-shirt,

NAME OF THE SEAM: ZIPPER ATTACHMENT

Diagram

Seam definition : The process of joining zipper between two cutting pieces of same size is known as zipper attachment.

Explanation of zipper attachment

Pattern Machine Sewing FabricFabric- 2 pieces,Zipper

Singer Domestic Sewing M/C,Needle Size: 16,Max Stitch per inch: 16,Bobbin and bobbin case

Stitch Per inch: 12,Sewing Thread: Cotton.

Type: poplin,

Working Process:

Step 1: Keep 2 pieces of fabric and 1 piece zipper

Step 2: 3” Super imposed stitch & 1” back tag stitch

Step 3: Join the zipper and make a zipper cover (fly piece)

Uses: Pant, Trouser, Skirts and ladies pant etc.

NAME OF THE SEAM: SLEEVE PLACKET

Diagram

a b c Sleeve placket

Seam definition: When three pieces of fabric join with one another which are made for sleeve as like placket is called sleeve placket.

Explantion:

Pattern Machine Sewing FabricFabric3 pieces,


Stitch Per inch: 12Sewing Thread: Cotton

Type: poplin

Working Process:

Step 1: to cut three pieces of fabric.

Step 2: Cut in the middle of © fabric.

Step 3: Left of © join with (a) and right of © join with (b).

Step 4: then stitch the sleeve placket.

Uses : Long shirt.

NAME OF THE SEAM: PIN TUCK

Diagram

Seam definition: When stitch is done after one inch to create pill structure is called pin tac.

Explanation :

Pattern Machine Sewing FabricFabric-1 piece,



Type: poplinSize:6x7,

Working Process : Step 1: to cut a piece of fabric of 6 x 7 Step 2: to make pill effect after 1 inch. Step 3: stitch over the pill effect Uses: Home decorative.

NAME OF THE SEAM: TROUSER SLANTED POCKTE

Seam definition: The pocket which is made for front part of pant is called pant front pocket.

Equipments and Materials:

Pattern Machine Sewing FabricFabric- 4 pieces,



Type: poplinColor: OrangeDifferent sizes by following pattern

Working Process

Uses: Trouser, male pants.

NAME OF THE SEAM: COIN POCKTEDiagram

Seam definition : The pocket which is made to keep coin for this reason it is known as coin pocket.

Explantion and Materials:

Pattern Machine Sewing FabricFabric- 5 pieces,



Type: poplinDifferent sizes by following pattern

Working Process:

uses: Pant, trouser.

Index

1. Super imposed seam.

2. Lapped seam.

3. Lap felled seam.

4. Bound seam.

5. French seam.

6. Gather.

7. Neckline with facing.

8. Patch pocket.

9. Rectangular patch pocket.

10. Box pleat.

11. Inverted pleats.

12. Piped seam.

13. Piping seam.

14. Dart.

15. Welted seam.

16. Continuous strip opening.

17. Slave placket.

18. Pin tucks.

19. Trouser Slanted pocket.

20. Coin pocket.

21. Zipper attachment.

22. Fly opening.

23. Welt pocket.

24. Jetted pocket.

Documents

seawing Room submisiion