Section16 Part1 A-H - Banta · PDF fileand trimmer models with spade terminal wire end. 135-053 Spark Plug Boot For many Chain Saws & Trimmers. ... Size: 1/8” ID X 3/16” OD (50

CHAIN SAW ACCESSORIES - O.E.M Banta

C C

Part# O.E.M Application Part# O.E.M Application

G G

Part# Application Part# Application440-034New Style Single Terminal Electronic Ignition Module This module comes in a metal case. Complete with instruction sheet, and fasteners. For use on Chain Saws, Brush Cutters, String-Trimmers and Hedge Trimmers that have had mechanical points originally.

For Carburetor Kits and Partsplease see our sections “10”, “11” &“12”

430-017

Toggle Kill SwitchUsed as an on / off switch. Found on many Chain saws and Trimmers using a single wire, self grounding type switch. Kill Switch found on many small chain saw and trimmer models with spade terminal wire end.

135-053

Spark Plug BootFor many Chain Saws & Trimmers.(Fits 5mm spark plug wire)

135-095

Spark Plug BootFor Lawn and Garden equipment. (Fits 7mm spark plug wire)

135-046

Spark Plug BootFound on Lawn and Garden equipment. (Fits 7mm spark plug wire.)

135-015

Spark Plug ClipUniversal application. Used in our 135-053 & 135-095 spark plug boots.

135-012

Spark Plug Clip Universal application. Used in our 135-046 spark plug boots

135-061

5mm Spark Plug WireQuality black hypolon outer case with COPPER (not carbon) inner wire. Used on many chain saw and trimmer application. (5mm wire OD X 10 meter roll).

(Sold in multiples of 10)





135-0047mm Spark Plug Wire.Quality black hypolon outer case with COPPER (not carbon) inner wire. For use on most Small engine / 4 stroke Lawn & Garden applications. (7mm wire OD X 20 FT roll).

TYGON FUEL LINE

115-300 Size: 3/32” ID X 3/16” OD (50 FT roll) 115-305 Size: 1/8” ID X 3/16” OD (50 FT roll)115-310 Size: 1/8” ID X 1/4” OD (50 FT roll) Special formulation vinyl and oil tubing for

Chain saws, Snowmobiles and Lawnmowers. Maintains an air tight seal on fittings even in extreme temperatures. Resists swelling or hardening. Translucent material allows visual inspection of flow. Temperature range 35 degrees below to 165 degrees F.For more sizes and information on Tygon Fuel Linessee our “FUEL LINE and ACCESSORIES” section

115-106NEOPRENE FUEL LINE (5 meter roll = 16.5 FTapprox). Neoprene fuel line is oil and gas resistant. Size: 1/8” ID X 9/32” OD. For many Chain Saw and Trimmer applications.

For additional fuel parts see our “FUEL LINE & ACCESSORIES” section 26610-014Fuel Filter - In TankUse with 1/8” ID fuel line. (felt material). Found on many older Homelite chain saws. Measures: 1-1/2” Long X 9/16” diameter.

610-022

Replacement felt for above Measures: 1” Long X 1/4” ID X 9/16” OD.

610-006

Fuel Filter - In TankUse with 1/8” ID fuel line. (felt material). Found on many chain saws. Measures: 1-1/2” Long X 13/16” diameter.

610-030

Replacement felt for aboveMeasures: 1” Long X 7/16” ID X 13/16” OD.



UNIVERSAL UNIVERSAL continued

16-01

Banta CHAIN SAW ACCESSORIES - O.E.M

C C

Part# O.E.M Application Part# O.E.M ApplicationPart# Application Part# Application614-527

Fuel Filter - In TankUse with 1/8” ID fuel line. Dual filtration felt and stainless steel mesh element. Used on engines up to 33cc.

614-528

Fuel Filter - In TankUse with 1/8” ID fuel line. Dual filtration felt and stainless steel mesh element. Used on engines up to 80cc.

613-601

Fuel Filter - In TankUse with 3/32” thru 1/8” ID fuel lines. Our most popular filter for small trimmers and chain saws. Measures: 1-1/4” long X 1/2” diameter.

613-602

Fuel Filter - In TankUse with 1/8” ID fuel line. Measures: 1-1/4” long X 1/2” diameter.

613-603

Fuel Filter - In TankUse with 3/32” or 1/8” ID fuel line. Fits Husqvarna chain saws and many others. Measures: 1-5/8” long X 11/16” diameter.

613-604

Fuel Filter - In TankUse with 1/8” ID fuel line.Measures: 1-5/8” long X 11/16” diameter.

613-605

Fuel Filter - In TankUse with molded fuel lines. (1/4” ID)Fits chain saw models with molded fuel lines. Measures: 11/16” OD X 1-5/8” overall length.

613-607

Fuel Filter - In TankFor use with molded fuel lines. Fits Stihl chain saw models: 034, 036, 038 etc with molded fuel lines. NOTE: Similar to our our 613-605 but larger diameter (23mm). Recommended for larger cc Stihl chain saws. 044, MS440, 046, MS460, 064, MS640, 066, MS660 etc. Measures:1-3/4” overall length X 23mm diameter.



415-623

Intake Gasket AssortmentThis assortment contains carburetor mount gaskets for Tillotson, TK, Nikki, Walbro and Zama carburetors. Gasket comes in a plastic container that is labeled for easy reordering. Includes 117 pieces in total. (Note: Individual gasket sold in packs of 10) See our “CARBURETOR KITS” section for more information and better carburetor mount gasket pictures.For other Chain saw related gaskets - See our “CHAIN

SAW ACCESSORIES - O.E.M.” section that follows this one. Done in alphabetical order by Chain Saw

Manufacturers name A thru Z

560-101Starter Dog / Starter Pawl (Large)Found on many older chain saws using an aluminum starter cup. Size: Dog width: 1/2” with a 3/8” ID.

560-102Starter Dog WasherThis is a fibre washer used on older Fairbanks Morse, Remington etc. chain saws that used a starter dog assembly and aluminum starter cup.

140-061

Starter HandleUniversal rubber handle with steel insert. For use with #4 thru #6 Starter Rope sizes.

560-123Starter HandleUniversal heavy duty Starter Handle. This large plastic handle has a removable cap for putting rope knot.

147-045Starter Rope #4-1/2 Premium 16 carrier smooth braid starter rope / starter cord. Red tracer. Smoother cycling. Flexibility increased while maintaining firmness. Wound on a plastic spool. (Made in Germany).(3.6mm or 9/64” diameter) X 100 FT.

For more starter rope sizes see our “STARTER PARTS” section 42



UNIVERSAL continued UNIVERSAL continued

16-02


C C

Part# O.E.M Application Part# O.E.M ApplicationPart# Application Part# Application775-080

Shop Repair TagsIndividually numbered with customer tear-off.

DOLMAR / MAKITA605-003 122 173 030

Air FilterFits Chain Saws model:122 Size: 3-3/8” L X 3-3/8” W X 1/2” HT

605-005 114 173 531Air FilterFits Chain Saws models: 113 and 116. Size: 4” L X 2-1/4” W X 7/16” HT

605-006 123 173 110123 173 120

Air FilterFits Chain Saws model: 123 Size: 3-5/8” L X 3-1/2” W X 3/4” HT

605-355 394 173 010Wacker# 0108076Wacker# 0108077

Air FilterFits Concrete Saws models: DPC6300, 6201, 7300C, 7301 also PC6212, PC6214, PC6412, PC6414, PC7312, PC7314 & PC8140. Also found on Wacker models: BTS; Diamond Products models: SC Size: 4-1/8” L X 3-5/16” W X 2-5/16” HT. (Also see our 605-356 and 605-358 filters)

605-358 394 173 030394 173 030AWacker# 0108074

Pre Cleaner For our 605-355. Fits model: DPC6401 cut off / cut quik saw. 3 Layer filter. (Filter construction 50 PPI, 60 PPI and 80 PPI layers, bonded together). (Also see our 605-358 and 605-355 filters).Size: 5-1/2” L X 3-5/8” W X 3/4” HT NOTE: Two images shown, (1) pre filter only >.

605-360 326 173 080

Pre Cleaner For our 605-355 (Newer Style). Fits Makita / Sachs Dolmar model: DPC811.Size: 7-3/4” L X 5-1/8” W X 11/16” HT.


(While Quantities Last)

605-362 395 173 090Pre CleanerFits Makita / Sachs Dolmar models: PC6412, PC6414, PC6530, PC6535, PC7312, PC7314, PC7430, PC7435, PC8116 and PC8240Size: 6-3/8” L X 5-3/8” W X 11/16” HT

605-350 395-173-010

Air FilterFits Concrete Saws models: Dolmar: PC6412, PC6414, PC6530, PC6535, PC7312. PC7314, PC7430, PC7435, PC8116 and PC8240. Makita: DPC6430, DPC6431, DPC6440, DPC6441, DPC7330,DPC7331, DPC7340, DPC7341, DPC8131 and DPC8132 Wacker: BTS 930 L3, BTS 935 L3, BTS 1030 L3, BTS 1035L3 and BTS 1140 L3. Size: 4-1/8” L X 3-5/16” W X 1-7/8” HT. (NOTE: Similar to our 605-355 but measures 1-7/8” high vs our 605-355 at 2-5/16” high).

605-356 394-173-020

Air FilterFits Makita / Dolmar / Sachs Concrete Saws. Models: DPC6200,6201, 6410, 6411, 7300, 7301, 7310 and 7311. Size: 3-11/16” L X 2-5/8” W X 1/4” HT. (Also see our 605-355 and 605-358 filters)

670-101Bar NutFor Chain Saw models: 112, 114, 117, 119 (8mm hex nut)

670-113Bar NutFor older chain saw models 122 & 123.

651-101 901 506 554119 213 030

Chain AdjusterFor Chain Saw models 112, 114, 117 & 119.

651-106 901 506 554119 213 030

Chain Adjuster Fits chain saw models: CA, CC, CT, 122, 123 also found on some older 144, 152 & 153.

651-194 123 213 010924 306 400922 606 000

Chain AdjusterFor Chain Saw models 123 and 133





UNIVERSAL continued DOLMAR / MAKITA cont.

16-03


C C

Part# O.E.M Application Part# O.E.M Application570-240 123 130 000

Cylinder Assy (47mm) Fits Chain saw model: 123, also fits old Concrete Saw model: 309 (old style)

570-258 123 130 200

Cylinder Assy (47mm)Fits new Concrete Saw model: 309 PC.

570-239 325 130 010325 130 030 325 130 031325 130 033325 130 034325 130 035Wacker#020277802027790206854

Cylinder Assy (47mm)Fits chain saw models: DSC6200, DPC6400 & DPC6410.

570-246 133 130 001

Cylinder Assy (52mm) Fits Chain Saw model: 133.

123

309 PC

DSC6200

DPC6400 & 6410

133

572-481 122 132 100

Piston assembly (47mm)Fits chain saw model: 123, also fits old concrete saw model: 309 (old style).

574-119 123 132 020

Piston Rings (47mm) Fits Chain Saw model: 123, also fits old Concrete Saw model 309.

640-207

Gasket Set Fits Concrete Saw model: 309 PC. Includes Oil Seals

640-204

Gasket Set Fits Chain Saw model: 123, 133, 133S, 143

640-206

Gasket Set Fits Chain Saw model: 153.

640-208

Gasket SetFits chain saw models: 120 and 120 Si.Includes Oil Seals

591-101 962 210 015

Bearing - PistonFits Dolmar Chain Saw models: 112, 114, 117 & 119.

570-001 Many Applications

Cylinder PlugFits Dolmar, Husqvarna, ICS, Makita, Partner, Stihl and Wacker cylinder assemblies. (For Decompression Valve see our part# 570-002)

570-002 001 131 150

Decompression Valve For Chain Saw and Concrete saw cylinder assemblies. Fits many Dolmar / Makita, cylinder assemblies. Dolmar models: 64XX, 73XX and 81XX; Makita models: DPC64XX, DPC73XX and DPC81XX (For plug only see our 570-001).


DOLMAR / MAKITA cont.DOLMAR / MAKITA cont.

16-04


C C

Part# O.E.M Application Part# O.E.M Application550-156 965 451 900Gas CapFits Chain Saw models 110, 112, 113, 114, 116, 117,119, 120, 123 and 133.

551-104 965 451 230

Oil CapFits Chain Saw models:CA and CT. (old)

625-325 100573

Starter Spring For Chain Saw model “D” JR 34.

625-577 108 163 010

Starter Spring Fits chain saw models: 103 and 108.

625-576 123 163 010

Starter SpringFits Dolmar chain saw models: 112, 133, 166, 307 and 311.

625-575 119 163 010144 163 010

Starter SpringFits Dolmar chain saw models: 112, 114, 117, 119, 122, 144, 166, 308 and 310.

654-106 112 310 010Wrap HandleFor Chain Saw models: 112, 114, 117,119 and 120. (While Quantities Last)

705-574

T-WrenchFits chain saw models: 112, 113, 114, 116, 117, 119, 120 and 120 Super. Size: A= 7”, B= 1-1/16”, C= 1”.Bar= 1/2” (13mm), Plug= 3/4” (19mm)

705-525T-WrenchFits chain saw models: CA, CC and CT Size: A= 7”, B= 1-11/16”, C= 1 5/8”. Bar= 11/16” (17mm), Plug= 13/16” (21mm)

A

B

C

A

B

C

605-307 130300 3973 0

Air FilterFor Chain Saw model CS5000 and CS5000, Type 1E serial# 001001 and higher. Measures: 2-1/2” OD X 1-3/4” ID X 1-1/4” HT

605-309 130313 3833 1

Air Filter For Chain Saw model CS4400 and CS510. (Tall version). Measures: 2-1/2” OD X 1-3/4” ID X 1-3/8” HT

605-007 130305 0033 3

Air FilterFits Chain Saw model: CS-60 Size: 4-1/4” L X 3-3/4” W

605-008 130305 03430

Air FilterFits Chain Saw model: CS-451 and CS-452 Size: 3-1/16” L X 2-3/4” W

605-014 130310 03930130310 03930 2

Air FilterFits Chain Saw model: 302 Size: 3-1/16” L X 2-5/8” W

670-101 43301912330

Bar NutFor Chain Saw models: C60, 452, 500, 510 and 550

651-201 43301613931

Chain AdjusterFor Chain Saw models: 280 and 290.

651-110 Echo

Chain AdjusterFor Chain Saw models: 302 and 315.



DOLMAR / MAKITA cont. ECHO

16-05


C C

Part# O.E.M Application Part# O.E.M Application651-112 EchoChain AdjusterFor Chain Saw model: CS - 60.

For ECHO Clutches - See our “Trimmer Parts” section.621-107 175018 0022 0Clutch Spring For Chain Saw model: CS - 60.Size: ____” diameter, ____ Overall Length

621-108 EchoClutch SpringFor Chain Saw models: 452, 601 and 602.Size: ____” diameter, ____ Overall Length

574-248 10001130830Piston Ring Set (52mm X 1.5mm) Fits Echo chain saw model: 8000. Aftermarket cast iron piston rings. Two piston rings included. Note: Some chain saw applications use one only piston ring.

550-103Gas CapFor Chain Saw models: 601, 702 and 750.

551-102 436000 0393 0

Oil CapFor Chain Saw models: 301, 351, 451, 452, 601, 602, 701 and 702.

551-103 177220 0023 0

Oil CapFor Chain Saw model: CS - 60S

622-498 100212 03930

Oil SealFor (Magneto Side). Fits Chain Saw models: 280, 302, 315, 330 and 351. Oil Seal For (PTO Side). Fits Chain Saw models 302 and 351. Measures:12mm shaftsize X 32mm OD

622-506 100212 11230Oil SealFor (PTO Side) Fits Chain Saw models: 280, 315, 330, 400 and 351. Measures: 12mm shaft size X 19mm OD

140-046 177228 0111 0Starter HandlePlastic starter handle. For use on small equipment applications. Ideal for small trimmers, brushcutters and chain saw applications.

625-476 177220 0283 4John Deere# MG67224

Starter Spring For Chain Saw models 451, 452, 500, 550, 600, 601, 602, 650, 701, 702, 750, 5500, 6700 and 8000. Fits John Deere models: 50V, 60, 70, 55EV, 65EV, 80EV and 60170.

625-477 177220 0393 0Fits chain saw models: CS-302, CS-351, CS-400, CS-440, CS-4600, CS-5000. For Generators / Pumps Spring - Fits models: PB-200 and 202. Trimmer Spring - Fits models: SRM200, 202, 300, 302, 351 and 400.

625-479 177220 0653 0

Fits chain saw models: CS-280, CS-290 and CS-330. Trimmer Spring - Fits models: KE140, 200 GT-140, 160, 200, 1000, SRM140, PB300E, PB210, PB211, SRM200, SRM200AE, SRM210E, SRM250E and PB330

705-574

T-WrenchFits chain saw models: 100, 315, CS451, 452, 550, 601, 602, 605, 660, 702, 802, 4500, 5500 & 8000Size: A= 7”, B= 1-1/16”, C= 1”. Bar= 1/2” (13mm), Plug= 3/4” (19mm)

FRONTIER605-808 Frontier

AYP# 35373Jonsereds# 100251

Air FilterFor Chain Saw model Mark-1, also found on small Husky, Jonsereds and Pioneer models. Measures: 3-7/8” L X 2-3/8”W

560-147 FrontierStarter PulleyFor all old style Frontier Chain Saw models without anti - vib. Found on Small Husky, Jonsereds and Pioneer models that were made by Frontier.

625-325 100073

Starter SpringFor all Frontier Chain Saw models. (Spring and metal band) Note: will also replace Frontier# 100573 - if you reuse the metal case


A

B

C

ECHO continued ECHO continued

16-06


C C

Part# O.E.M Application Part# O.E.M Application605-121 69681 / A65178Air Filter For Chain Saw models Super Mini, EZ- Automatic and Super EZ. Size: 4” L X 2-7/8” W X 1/16” HT.

605-105 587741 / 63589 AAir Filter For Chain Saw models XL-12 and Super XL. Size: 4” L X 3-1/2” W X 3/4” HT

605-139 D92702B A24779 / 69141

Air Filter Fits Chain Saw models XL, XL-2 and Super 2. Size: 2” L X (1-3/8” - 1-5/8”) W X 1/2” HT

605-143 02500Air Filter Fits Chain Saw models 180,192 and 200 - also fits Little Red XL, Super 2 and Green Machine model 20

651-396 63225 / 93039

Chain Adjuster For Chain Saw models XL12, SuperXL,410, 450, 540. Also fits chain saw model 550

651-397 69254-1A / 69254-2802202A00440

Chain AdjusterFor Chain Saw models XL, XL-2, Super 2, VI Super 2, 240 and 245.

621-110 65842

Clutch Spring For Chain Saw models: XL-113, XL-114 and XL-122.

572-195Piston Assembly (46mm)For chain saw model: XL-Super.

623-597 637781

Head GasketFor Chain Saw models XL-922, 923, 925 and Concrete Saw model XL-98 Cut-off saws.

610-345 63718 / 69451UP06862

Duck Bill ValveFor chain saw models XL, XL-2 and Super 2. Duck Bill Valve - Found on Trimmers and Chain Saws. Measures: .100” ID X .201” OD X .25” L

115-645 70310-987031098

Homelite Fuel Line (50 FT) For use on Homelite and McCulloch Chain Saws and Trimmers. Measures: 7/64” (.109”) ID X 13/64” (.209”) OD with a 3/64” (0.047”) wall thickness. Sold and Priced in 50 foot rolls, Gray in colour.

610-212 63744A63745A

Molded Fuel Line For chain saw models XL-12 and Super XL-12. Measures: 9” overall length with a .308” OD grommet at 6-5/16”

610-014 A-69923

Fuel Filter AssemblyUse with 1/8” ID fuel line. (felt material). Found on many older Homelite chain saws. Measures: 1-1/2” Long X 9/16” diameter

610-022 64083 / 640831

Fuel Filter Felt Replacement felt filter for our 610-014 in-tank fuel filter. Fuel Filter for many Poulan chain saw models. Measures: 1” Long X 1/4” ID X 9/16” OD.

610-006

Fuel Filter AssemblyUse with 1/8” ID fuel line. (felt material) Found on many older Homelite chain saws. Measures: 1-1/2” Long X 13/16” diameter.

610-030 59253 / 592531A

Fuel Filter - Felt Replacement felt filter for our 610-006 in-tank fuel filter. Measures: 1” Long X 7/16” ID X 13/16” OD.

613-601 49422 / 96639UP 0387

Fuel Filter - In TankOur most popular filter for small Homelite and McCulloch trimmers and chain saws. Also fits many other applications. Measures: 1-1/4” long X 1/2” diameter.

550-102 DA92701C

Fuel and Oil Cap Kit Fits chain saw models XL, XL-2, Super 2, VI Super 2, 180, 190, 200, LX30, 240 and Super 240. Kit includes: (1) fuel and (1) oil cap shown



HOMELITE HOMELITE continued

16-07


C C

Part# O.E.M Application Part# O.E.M Application600-874 94711A

94711B94711BS94711CSUP03903

Electronic ModuleFits Chain Saw models XL, XL-2, Super 2,190, 240, 245, P100-1, Super 200 and 240, also fits trimmer models ST-100, 120, 145, 155, 160A, 180, 200, 210, 245, HB-280, 380, 680 and HD-480.

600-957 A79261A79641A94111S

Electronic IgnitionFits Chain Saw models XL-76, XL-130 & Super Mini. Will also fit Pioneer Chain Saw model P-41 if the original Pioneer lamination is reused.

Note 1: You will have to reuse your original Pioneer lamination. For Pioneer P41 applications we DO NOT recommend purchasing unless you have some small engine repair knowledge. Note 2: BANTA purchases these modules from the O.E.M. vender and there is “No Warranty” on these modules. They are tested by the Manufacturer before they are shipped. The most important thing to remember when installing a 600-957 is that you have a good ground connection. (Prestolite Module - Blue). Our 600-957 WILL NOT replace Phelon module Pioneer# 430938 / 507-430938).

623-322 59274Chainsaw Exhaust Gasket Muffler exhaust gasket forchain saw models XL-12 and Super XL-AO.

636-409 68748A59052AA68748UP06580

Muffler / ExhaustMuffler for Chain Saw newer model XL-12. New (3) bolt style, comes complete with bolts, spacers and baffle. Size: 3-7/16” X 2-7/8 X 2-5/16” Depth. (3) 3/16” ID mounting holes. The top (2) mounting holes are on 2-7/8” centers. Exhaust intake hole measures: 1-9/16” X 5/8”.Picture shows Top and Bottom views (1) muffler only > NOTE: Will fit old style (2 bolt) type but you will have to cover the third hole.

560-300 97768A / PS03117UP05460

Sarter PulleyFor Chain Saw models XL, Super 2, 240, 245, 250, 300 and Trimmermodels ST-80,100 & 200. Measures: 2-9/16” OD

625-107 69217

Starter Spring For Chain Saw models: XL, XL-2, Super 2, 190 and 240. Trimmer Spring - Fits models: ST80, 100, 120, 200 and 210.



625-115 A94918A

Starter SpringFor Chain Saw model 330. Generator / Pump SpringFits models: HB 280, 480 and 680.

625-116 94842 / A94842

Starter SpringFor Chain Saw models XL-12, XL-15, Super XL, Super XL-AO and XLBC-4 and XL-Automatic Trimmer Spring - Fits model: ST400.

625-117 A98326

Starter SpringFor Chain Saw models 290 and 340.

705-534T-WrenchFits chain saw models: Super XLAO, XL-12 Size: A= 7”, B= 1-9/16”, C= 1-1/2”. Bar= 5/8” (16mm), Plug= 3/4” (19mm)

705-535T-WrenchFits chain saw models: XL-76, XL-130 & “C” series. Size: A= 7”, B= 1-5/8”, C= 1-9/16”. Bar= 5/8” (16mm), Plug= 13/16” (21mm)

HUSQVARNA605-085 530 02 98-11

Air FilterFits chain saw models: 136, 137, 141, 142, 36 and 41.

605-066 503 15 19-03

Air FilterNylon mesh styleFits Chain Saws models 238 and 242.

605-173 501 80 71-01501 80 71-05

Air FilterFits Chain Saw models 61, 66, 261, 266, 281 & 288. Nylon mess style (2 bolt) Size: 3-1/2” L X 3.735” W X 1-3/8” HT

A

B C

16-08

HOMELITE continued HOMELITE continued


C C

Part# O.E.M Application Part# O.E.M Application605-062 503 81 45-02

503 81 45-03 575 26 91-03

Air FilterFor Chain Saw models 362, 365, 371 & 372. Size: 3-5/8” L X 2-7/8” W X 1-5/8” HT

605-159 506 26 34-01506 26 34-02

Air filterFor Cut-off Saw Size: 3-23/32” L X 3-3/4” W X 2-1/16” HT. Note: Two images shown for reference.

605-160 506 26 91-01Pre FilterFor our 605-159. Fits cut-off saw models: 371K and 375K. 3 layer foam filter. Size: 7-5/8” L X 4-7/8” W X 3/4” HT

605-156 506 14 58-01

Air filterFor Cut-off Saw model 268K and 272K. Size: 4-1/16” L X 4” W X 3-3/16” HT Note: Two images shown for reference(For use with our pre filter 605-155).

605-155 506 14 57-01

Pre-filterFor our 605-156. Fits Cut-off Saw models 268K and 272K. Note: Image shows both top and side (3 laminated layers for filtration). Size: 5” L X 4-1/2 to 4-7/8” W X 3/4” HT.

605-171 506 26 86-01

Pre FilterFor cut-off saw. Fits model: 3120K. 3 layer foam filter. Size: 8” L X 6” W X 3/4” HT.

605-440 506 23 19-01

Pre Filter(3) Layer foam filter. Fits models: K950 Active and K960 Cut Quik saws. Size: 10-3/8” L X 5-1/4” W X 3/4” HT approximately. (Also see our 605-438 Air Filter)

605-024 503 44 72-03503 44 72-04

Air FilterFits chain saw models: 262, 268, 272, 394.Size: 3-9/16” L X 2-9/16” W Overall Height: 1-1/4”.

605-064 503 89 81-01503 89 81-02

Air FilterFits chain saw models: 51 and 55. This filter is the commonly used flock design. Air filter is held in place with a screw (screw provided). Oil-less type filter.

605-060 537 02 40-03Air Filter. (Twist on)Fits the following chain saw models: 340, 345, 346, 350, 351 and 353; Air filter attaches by simply twisting on the carburetor manifold. Note: Some 346 and 353 models use a steel snap to connect. See picture for clarification.

605-028 503 44 72-03Air FilterAssembly for chain saw models: 262, 268, 272 & 394.

605-378 506 36 72-01506 36 72-02544 18 16-01

Panel Air Filter For Concrete / Cut Quik Saw model: K750. Base Size: 4-15/16” L X 4-1/2” W X 1-3/8” HT. (For use with our 605-377 pre filter)

605-377 506 36 71-01

Pre filter Fits Cut Quik Saw model: K750. Size: 7-5/64” L X 5-1/2” W X 13/16” HT. (Use with our 605-378 air filter)

605-063 537 20 75-01Air FilterFits models: 570, 575 and 576. Nylon mesh style. Size: 3-3/8” L X 3-1/4” W X 2-1/8” HT approximately. Note: Air filter only, does not include knob or mounting screw.

605-460 505 31 55-30

Air Filter For Husqvarna and Partner concrete / cut quik saws. For Husqvarna model: K185 and Partner models: K1200 and K1200 Mark II. Size: 5-7/8” OD X 4-1/8” ID X 2-1/2” HT

670-101 503 22 00-01

Bar Nut (8mm)Fits many chain saw manufacturers chain saws. Fits models: 41, 44, 444, 50, 51, 55, 61, 66, 162, 181, 266, 268, 280, 285, 380, 2100 etc. Size: 8mm X 1.25 thread. For 13mm T-wrench


16-09

HUSQVARNA continued HUSQVARNA continued


C C


Bar Plate For chain saw models 61, 66 and 266. (New Style)

653-127 537 01 37-71

Bar Plate For chain saw models: 362, 365, 372 and 385.

592-106 738 22 02-25Crankshaft BearingFits many Chain Saw models. Measures: 15mm ID X 35mm OD X 11mm HT (Bearing# 6202)

875-724 506 07 05-20 506 34 74-20 506 34 74-23 506 37 27-03 506 37 27-20

Drive belt (cogged belt) Fits models: 371K and 375K cut-off saws & Partner K950 cut off saws with 12” and 14” blades. Size: 3/8” W X 34-1/2” L

875-712 506 29 67-02 544 90 84-02

Drive Belt (multi-rib)For concrete saw model: K750. Size: .551” W X 32” L (6 rib, polyester cord construction)

875-725 506 07 05-04 506 34 74-24

Drive Belt (cogged)For concrete saw model: K950 Active with 16” blades. Size: 3/8” W X 36” L

875-711 506 03 30-31 506 27 67-41

Drive Belt (cogged)For concrete saw model: K650 Active, K650 Active II & K700 Active II. Size: 1/4” W X 31-1/2” L

657-123 501 53 05-01

Av BufferAnti Vibration Dampings For chain saw models: 61, 162 (old) and 480, with metal crankcase. Measures: 5/8” OD X 15/16” overall length

657-122 501 27 23-01501 27 63-01

Av BufferAnti Vibration Dampings for chain saw models: 61, 162 (old) & 480, with metal crankcase. Size: 7/8” OD X 1-3/32” overall length. Also found on some Makita / Dolmar saws.


657-131 501 62 87-01

Anti Vibration Dampings (Light) For chain saw models: 36, 41, 42, 61, 66, 136, 141, 162 (new), 238, 242, 246, 266, 268 and 272 with plastic crankcase. Also fits Husqvarna cut quik saw models: 268K & 272K. Fits Jonsereds saw model: 670. Measures: 5/8” OD X 1-1/16” overall length. (For larger diameter (Medium) Av buffer see our 657-132).

657-132 501 62 87-01Av BufferAnti Vibration Dampings (Medium) for chain saw models: 36, 41, 42, 61, 66, 136, 141, 162 (new), 238, 242, 246, 266, 268 and 272 with plastic crankcase. Also fits cut quik saw models: 268K and 272K. Measures: 3/4” OD X 1-1/16” overall length.

657-133 501 69 94-01501 77 35-01

Av BufferAnti Vibration Dampings (Large) for chain saw models: 61, 162 (new), 66, 266, 268 and 272 with plastic crankcase. Measures: 7/8” OD X 1-5/16” overall length

657-124 501 81 47-01 / 501 81 47-02

AV Buffer Anti Vibration Dampings for chain saw models: 181, 262, 281, 288 and 3120. Measures: 15/16” OD (coarse threaded male end), 13/16” OD (fine threaded female end) X 1-1/2” overall length.

657-125 501 76 39-02

AV BufferAnti Vibration Dampings for chain saw models: 50, 51, 55 and 55 Rancher. (1984 thru 2007) Measures: 5/8” to 11/16” Tapered OD X 1-5/16” overall height.

657-137 503 85 41-01

Anti Vibration Dampings For chain saw models: 340, 345, 346, 350, 351, 353, 357, 359, 455 and 460. Measures: 19.85mm OD X 48mm Overall Length. This measurement does not include the internal threaded bolt.

657-127 503 52 87-02

AV BufferAnti Vibration Dampings for chain saw models: 394 and 395. (2003 thru 2010) Measures: 19mm OD X 52mm Overall Length. This measurement does not include the internal threaded bolt.

657-126 503 63 75-03

AV BufferAnti Vibration Dampings for chain saw models: 362, 362 XP, 365, 371, 372 and 575. (Hard), Front upper handle (1999 - 2007) Measures: 18mm OD X 46mm Overall Length. This measurement does not include the internal threaded bolt.

16-10



C C

Part# O.E.M Application Part# O.E.M Application657-128 503 63 76-02AV BufferAnti Vibration Dampings For chain saw models: 362, 362 XP (1999 thru 2005), 365 (1996 thru 2009), 371 (1999 thru 2004), 372 (1999 thru 2011) (HARD), Rear AV / anti vibe mount. Measures: 22mm OD X 46mm Overall Length.Will also replace Husqvarna# 503637601 (Std). Overall measurement includes threaded (5mm) female insert piece.

657-129 503 89 56-02

AV BufferAnti Vibration Dampings For chain saw models: 362, 362 XP (1999 thru 2005), 365 (96 thru 2009), 371 (99 thru 2004), 372 (1999 thru 2011) (HARD), Front AV / anti vibe mount. Measures: 22mm OD X 46mm Overall Length.Will also replace Husqvarna# 503895601 (Std) . Overall measurement includes threaded (5mm) female insert piece.

606-316 503 74 39-01

Carburetor Rubber ElbowIntake Manifold - Rubber. Fits chain saw models: 362, 365, 371 and 372.

651-173 501 45 27-01501 45 27-02501 45 41-01501 54 63-01

Chain AdjusterFor chain saw models: 44, 50, 50 Rancher, 238 and 444.

651-172 501 53 71-01

Chain Adjuster For chain saw models: 51, 61, 162, 181, 266, 268 & older model 272 XP; also found on older Jonsereds models 630 & 670.

651-192 501 43 27-01501 45 27-02501 81 73-01501 81 92-01

Chain AdjusterFor chain saw models: 55, 154 and 254.

651-113 501 15 43-02501 22 68-01501 24 81-01

Chain AdjusterFor chain saw models: 65, 77, 180, 280 & 380.

651-175 537 07 12-01

Chain Adjuster Assembly For chain saw models: 340, 345, 346, 350, 351, 353, 357 and 359. (Includes part#’s 503869101 and 503885401);

651-174 537 04 04-21537 04 41-02537 07 95-01

Chain AdjusterFor chain saw models: 362, 362 XP, 365, 372, 385, 570, 575 and 576.

651-138 503 46 77-01

Chain Adjuster For chain saw models: 394, 394 XP, 395 and 395 XP.

621-111 501 20 87-01

Clutch Spring For chain saw models 65, 77 and 380.

621-144 501 40 34-02Clutch Spring For chain saw models: 61, 66, 162, 266 and 266 XP.

621-145 501 40 45-01Clutch SpringFor chain saw models: 44 and 444.

621-112Clutch Spring For chain saw model: 35 and Jonsereds model: 361, also Pioneer model P12. That were manufactured by Frontier.

621-156 504 21 00-16Clutch Spring For Chain Saw models 40 and 41

621-114 501 45 61-01

Clutch Spring For models: 50, 51, 55, 55 Rancher, 244R, 244RX,254, 257, 261, 36R, 44, 444. Overall Length: 5-3/8”.

621-115 503 14 51-01

Clutch Spring For models: 281, 288, 3120, 334T, 335XP, 336, 338, 339, 385, 390, 394, 395, K960 and K1250. Overall Length: 1-1/8” X 7/16” OD.

646-150 501 45 54-03

Clutch AssemblyFor chain saw models: 50, 51, 55, 54, 254, 257 and 261.Measures: 2.610” OD X 0.453” Thick.

646-152 537 10 34-01537 10 34-03

Clutch AssemblyFor chain saw models: 357 and 359. Measures: 2.640” OD X 0.400” Thick.

16-11



C C


501 77 85-02503 52 79-01503 74 44-02

Clutch AssemblyFor chain saw models: 61, (afterSerial# 602497), 66, 266 (after serial# 6051313), 268 and 272. Measures: 3.057” OD X 0.475” Thick.

646-113 501 77 85-01

Clutch Assembly For chain saw models:61, 66, 266, 266XP, 268 and 272; Measures: 3.057” OD X 0.512” Thick. (Also see our 646-153 newer style).

646-154 503 74 44-01

Clutch AssemblyFor chain saw models: 362, 365, 371, 372, 385, 390 and 575. Measures: 3.057” OD X 0.471” Thick.

646-155 503 70 15-02

Clutch AssemblyFor chain saw models:281, 288 & 395 (after Serial# 003900001) Measures: 3.045” OD X 0.542” Thick.

570-241 503 87 00-73

Cylinder Assy. (40mm)Fits chain saw model: H340.

570-254 503 53 68-01503 53 68-02

Cylinder Assy. (42mm) Fits chain saw models: 242 and 242XP.

H340

242 & 242XP

570-264 503 50 39-01503 50 39-02503 50 39-03

Cylinder Assy. (45mm) Fits chain saw models: 254 & 254XP.

570-285 503 16 83-01503 60 91-71

Cylinder Assy. (45mm)Fits chain saw model: 51. (For 46mm cylinder assembly see our 570-284)

570-284 503 16 91-71503 60 91-02 503 60 91-08503 60 91-72

Cylinder Assy. (46mm)Fits chain saw model: 55. Note: This will also fit on the smaller bore model 51

570-283 537 15 73-02

Cylinder Assy. (47mm)Fits chain saw models: 359 and also 357XP.

570-252 503 53 20-71

Cylinder Assy. (48mm) Fits chain saw model: 61.

254 & 254XP

51

55

359 & 357XP

61

16-12



C C


503 54 11-72 503 90 79-71

Cylinder Assy. (48mm)Fits chain saw models: 262. Note: Decompression valve NOT included, use our 570-003 De-compression valve. Bore: 48 mm, Stroke: 34 mm, Displacement: 62 cc, Rings: 48 mm X 1.5 mm.

570-282 501 41 78-01

Cylinder Assy. (48mm) Fits chain saw models: 65 and 265.

570-286 503 69 10-73503 93 90-03

Cylinder Assy. (48mm)Fits chain saw models: 365.

570-280 501 65 85-71 503 61 10-71 544 22 29-02

Cylinder Assembly (50mm)Fits chain saw models: 268, 268 S, 268 K and 268 XP. Note: Dealers have used this Cylinder and Piston on Husqvarna Chain Saw model 272. Same as our 570-279 but 2mm smaller bore and does not include a hole for a decompression valve. Uses our 572-524 replacement piston assy.

570-279 503 60 96-71 503 75 81-71 503 75 81-72 504 01 68-02

Cylinder Assembly (52mm) Fits chain saw models: 272, 272K.Same as our 570-280 but this cylinder assembly has a hole for a decompression valve and has a 2mm larger bore. (Note: Cylinder Plug only included for decompression valve see our 570-002 or 570-003). Uses our 572-715 replacement piston assy.

262

65 & 265

365

268 & 268S

272 & 272K

570-287 503 62 64-72 503 62 64-73503 93 90-05 503 93 93-71 503 93 93-72 503 96 52-71

Cylinder Assy. (52mm)Fits chain saw models: 362, 371, 372 and 375.

570-270 506 386 171520 757 302

Cylinder Assy. (51 mm)Fits cut quik saw models: K750.

570-288 503 90 74-01503 90 74-71

Cylinder Assy. (54mm) Fits chain saw models: 181, 281 and 288.

570-289 503 99 39-71

Cylinder Assy. (56mm)Fits chain saw models: 395.

570-271 506 15 55-06

Cylinder Assy. (56 mm)Fits cut quik saw model: K950.

362 &371

K750

181, 281 & 288

395

K950

16-13



C C

Part# O.E.M Application Part# O.E.M Application570-269 506 29 42-71A

Cylinder Assy. (60mm)Fits chain saw models: K1250, 3120 and 3120K

572-501 503 51 32-01

Piston Assembly (42mm)For chain saw models: 242 and 242XP.

572-701 503 73 02-71

Piston Assembly (44mm)Fits chain saw models: 246.

572-700 503 89 96-71

Piston Assembly (44mm)Fits Chain saw models: 350 & 351.

572-703 503 16 77-01


572-704 503 60 81-01503 60 81-71

Piston Assembly (46mm)Fits chain saw model: 55, older style.

572-706 503 92 04-71537 21 96-02

Piston Assembly (46mm)Fits chain saw model: 357.

Note 1: Replaces Husqvarna# 503 92 04-71 before SN 020700001Note 2: This Piston Assembly will also work in chain saw model 257.

572-705 537 15 72-02

Piston Assembly (47mm) Fits chain saw model: 359.

Note: Dealers have also used this piston assembly in Jonsereds chain saw model: 2059.

K1250, 3120& 3120K

572-708 537 29 30-02


572-499 503 53 90-02

Piston Assembly (48mm) For chain saw model:61. Note: Will also fit Jonsereds chain saw model 630.

572-526 501 20 56-03

Piston Assembly (48mm)For chain saw models: 65 and 265. (While Quantities Last)

572-714 503 69 13-71

Piston Assembly (48mm)Fits Chain Saw model: 365. (Replaces our old# 572-806)

572-710 503 53 11-71


572-524 501 65 94-03

Piston Assembly (50mm)For chain saw models: 268, 268 S, 268 K & 268 XP.

Note: Will also fit Jonsereds model 670.

572-807 501 65 88-03

Piston Assembly (50mm)Fits selected 670 Jonsereds chain saw models.

NOTE 1: Also fits Husqvarna chain saw model: 272 (older models) and will fit model: 266 / 266 XP with 50mm bore.

NOTE 2: Our 572-524 piston assembly was also used in older Husqvarna 268 models - see actual piston pictures for proper reference. For 52mm piston assembly see our 572-715.

572-718 503 28 90-42503 69 12-71503 69 14-71503 93 92-71

Piston Assembly (50mm) Fits chain saw models: 362, 371 & 372 (pre 1998).

Note: Will also fit Jonsereds chain saw models: 2071 and 2171

16-14



C C


Piston Assembly (51mm)Fits chain saw models: 575 & 299. (51mm X 1.2mm).

572-715 503 60 98-02503 60 98-03

Piston Assembly (52mm)Fits chain saw model: 272P.

572-716 503 50 27-02


572-719

Piston Assembly (52mm)Fits chain saw model:285.

572-720 503 50 60-02

Piston Assembly (54mm) Fits Chain Saw model : 288 (older style).

572-717 537 16 98-71

Piston Assembly (54mm)Fits chain saw model: 385

Note: Piston rings = 1.2mm thick

572-724 537 42 02-02

Piston Assembly (55mm)Fits chain saw models: 390, 390XP & 390 XPW.

Note: Piston Rings = 1.2mm thick

572-721 503 46 02-02


Note 1: Piston rings measure 1.5mm thickNote 2: Overall Height = 49mm, (1mm) higher than our 572-722.

572-722 537 13 76 71


Note 1: Piston Rings = 1.2mm thick

572-723 503 48 87-03


572-730 501 89 41-03

Piston Assembly (60mm)Fits chain saw models: 3120 / 3120 EPA.

574-200 530 02 96-05530 02 98-05

Piston Ring Set (38mm X 1.5mm) Fits chain saw models: 36, 136, 137 and 235.

574-206 503 28 90-02Piston Ring Set (40mm X 1.5mm) Fits chain saw model: 141, 142 and 340.

574-212 503 28 90-05Piston Ring Set (42mm X 1.5mm) Fits chain saw models: 42, 45, 242, 246, 345 and 346.

574-159 503 28 90-05Piston Ring (42mm X 1.5mm)Fits Chain Saw models: 242 and 242 XP

574-216 503 28 90-10Piston Ring Set (44mm X 1.5mm) Fits chain saw models: 49, 50, 51 EPA, 350 and 351.

574-161 503 28 90-11Piston Ring (45mm X 1.5mm)For chain saw models: 254 and 254XP.

574-221 503 28 90-14Piston Ring Set (46mm X 1.5mm) Fits chain saw models: 55, 257, 357 and 359.

574-230 503 28 90-29Piston Ring Set (47mm X 1.5mm) Fits chain saw models: 359 and 362.

574-157 501 20 50-01501 20 56-02503 28 90-15

Piston Ring (48mm X 1.5mm)For chain saw models: 61, 65, 265.

16-15



C C


503 28 90-17Piston Ring (50mm X 1.5mm) Fits Chain saw models: 266, 266 XP, 268, 268 S, 268 K and 268 XP

574-242 503 28 90-42Piston Ring Set (50mm X 1.5mm) Fits chain saw models: 266, 268, 362, 371 and 372.

574-248 503 28 90-19

Piston Ring Set (52mm X 1.5mm) Fits chain saw models:272 and 281.

574-254 503 28 90-22

Piston Ring Set (54mm X 1.5mm) Fits chain saw model: 288.

574-260 503 28 90-24

Piston Ring Set (56mm X 1.5mm) Fits chain saw models: 394 “Non EPA” and 2101.

NOTE: Some chain saw applications use only one piston ring.570-001 Many Applications

Cylinder Plug Fits Dolmar, Husqvarna, ICS, Makita, Partner, Stihl and Wacker cylinder assemblies. (For Decompression Valve see our part# 570-002)

570-002 503 66 56-01503 71 53-01

Decompression ValveFor Chain Saw and Concrete Saws. Fits models: K650 and K700 Active I, II and III, K750, K950 and K1250.(For plug only see our part# 570-001)

570-005 503 66 56-01

Decompression Valve (Blue Knob) For Chain Saw and Concrete saw cylinder assemblies. Fits Husqvarna, Jonsereds & Partner models: K1250 etc. Overall Length: 1-7/8” - Blue knob with 2 holes in nut. Similar to our 570-003 but with a longer main body.

570-003 503 71 53-01

Decompression Valve For Chain Saw and Concrete saw cylinder assemblies. Fits models: 254, 257, 261, 262, 268, 272, 281, 288, 357, 359, 362, 365, 371, 372, 385, 394 and 395 etc.Overall Length: 1-7/16” - Blue knob with 2 holes in nut.

590-149 501 52 84-02Crankshaft Assembly For Husqvarna chain saw models: 61, 66, 266, 266 XP, 268, 268 XP & 272; older models before 1993 with larger flywheel nut.

592-106 738 22 02-25Crankshaft BearingFound on many models. Measures: 37/64” ID X 1-3/8” OD X 7/16” HT. Measures: 15mm x 35mm x 11mm (Bearing# 6202 - open both sides)

590-165 503 61 33-71

Crankshaft AssemblyFor chain saw models: 61, 66, 266, 266 XP, 268, 268 XP and 272; after 1993

640-354

Gasket Set Fits chain saw models: 254 and 257.

640-243

Gasket Set Fits chain saw models: 61 and 66. (Includes oil seals)

640-220

Gasket Set Fits chain saw models: 266, 266 XP and 162. (Includes oil seals)

640-183

Gasket Set Fits chain saw models: 268 and 268 XP.

640-224

Gasket SetFits chain saw models: 365 and 372. (Includes oil seals)

640-371

Gasket Set Fits chain saw model: 271.

16-16



C C

Part# O.E.M Application Part# O.E.M Application640-388Gasket Set Fits chain saw model: 288.

640-394

Gasket SetFits chain saw model: 394.

640-235Gasket Set For chain saw model: Rancher 50.

640-360 506 38 53-05

Gasket SetFits cut quit / concrete saw models: K750 and K760.

640-186

Gasket SetFits Husqvarna / Partner cut quit / concrete saw model: K950. (Includes oil seals).

623-820 501 51 22-01

Head / Base GasketFor chain saw models: 61, 162, 66, 266 & 266XP

623-751 506 37 67-01

Head / Base Gasket For cut quik / concrete saw models: K750 and K760.

623-499 506 15 82-01

Head / Base Gasket For cut quik / concrete saw models: K950.

623-868 503 49 10-02503 49 10-01

Head / Base Gasket Fits chain saw model: P-650 and concrete saw models: K-650 (both old and new) and K700, Active I, II and III.

623-822 503 96 15-01

Head / Base Gasket onlyFits chain saw models: 362, 365, 372, 372 & 375; also fits Jonsereds models: 2065, 2071, 2162 and 2171.

613-603 503 44 32-01Fuel Filter - In Tank. Fits chain saw models: 36, 40, 41, 42, 45, 50, 51,55, 61, 66, 394 and many others. Use with 3/32” or 1/8” ID fuel line. Measures: 1-5/8” long X 11/16” diameter.

610-141 501 28 59-01 501 28 59-02503 50 97-01

Molded Fuel Line Fits chain saw models: 61, 66, 266 etc. Measures: 5-1/16” overall length.

610-151 501 51 99-01

Oil Pipe For chain saw models: 61, 266 and 266 XP. (Also found on Jonsereds Chain Saw model 630)

550-151 501 81 96-01501 81 96-02530 07 12-66537 21 52-02

Gas CapFor chain saw models: 36, 41, 42, 50, 51, 55, 154, 181, 234, 238, 254 / XP, 262, 281, 288, 345, 365, 394, 3120 - also fits Cut-off Saw models 371K, 375K and 3120K. Gas & Oils Cap For Chain Saw models: 181, 281, 288, 394.

551-107 501 43 14-01501 43 14-02501 56 45-01501 56 45-02501 56 45-04501 76 56-02

Gas CapFor chain saw models: 44, 61, 66, 162, 65, 77 (new), 266 / XP, 268 / XP, 272, 380, 480, 2100 and 2101

551-153 501 76 56-01501 76 56-02

Oil Cap For chain saw models: 36, 41, 50, 51, 55, 136, 141, 154, 254, 254XP, 257, 261 and 262.

551-145 501 62 66-01

Oil Cap For chain saw models:44, 61, 66, 162, 234, 238, 266, 266 XP, 268, 268 XP and 2100.

627-061 501 51 33-10501 51 38-01

Oil Pump Drive Gear This nylon gear fits chain saw models: 61, 66, 266, 268 and 272.

16-17



C C


Oil Pump Worm Gear. Fits chain saw models: 362, 365, 371, 372 & 375.

627-266 501 51 25-01501 51 38-01501 83 17-01

Oiler / Oil Pump Assembly Fits chain saw models: 61, 66, 266, 268, 272. Includes all three pieces shown.

627-281 503 69 81-01

Oil / Oil Pump AssemblyFits Chain Saw models: 281 and 288

627-270 503 52 13-01503 52 13-05

Oiler / Oil Pump Assembly Fits chain saw models: 365, 371, 372, 385, 390, 570 and 575.

600-185 503 62 02-01503 62 02-02503 62 02-03503 90 14-01506 16 90-02544 01 84-0194114601

Electronic IgnitionFor Chain Saw models: 45, 51, 55, 254, 257, 61, 262, 268, 272 and 394. For Jonsereds model: 630 chain saw.Note: Includes spark plug boot, not shown.

600-180 545 06 39-01 530 03 92-39

Electronic IgnitionFits chain saw models: 137, 142

600-164 501 51 62-01 501 51 62-02 501 61 73-02

Electronic Ignition Fits chain saw models: 61 (old), 66, 266 and 33The electronic ignition component is connected with the ignition coil to achieve full ignition. This type of ignition module utilizes transistor switches for magnet activation.

600-162 503 96 24-01 / 503 96 24-02 503 96 24-03 / 503 96 24-04503 96 24-05 / 503 96 24-06537 16 21-01 / 537 16 21-04 537 16 21-05 / 537 16 22-01 537 16 22-04 / 537 27 74-01 544 04 70-01 / 544 04 71-01 544 04 72-01 / 544 04 72-02

Ignition Module For chain saws. (Non RPM Limited). Fits models: 334, 335, 336, 338, 339, 340, 345, 346, 350, 351, 353, 357, 359, 362, 365, 371, 372, 385, 390, 570 & 575.

430-163 501 52 66-02 503 08 97-02 503 71 79-01 503 91 79-01

On / Off Switch For Chain Saw models: 36, 41, 50, 51, 55, 61, 266, 266 XP, 268, 268 XP, 272, 281, 340, 345, 394 & 395. (Made to O.E.M. Specs.) Two pictures shown for reference

430-180 503 71 82-01

Stop Switch or On / Off Switch For Chain Saw models: 232L, 232R, 235FR, 235R, 324LDX, 324LX, 324RX, 326, 336, 339XPT, 385. For Trimmer models: 123C, 123HD, 123L, 123LD, 225AI, 225B, 225BX, 225E, 225H, 225HBV, 225L, 225LD, 225 LITE, 225R, 225RD, 225RJ, 227L, 227JD, 227R, 227RD, 227RJ, 232L, 232R, 232RD, 232RL, 235R, 235RL, 240, 240R, 240RBD.

636-142 503 74 91-01501 76 66-02

Muffler / Exhaust For chain saw models: 51 and 55. Exhaust mounting holes are 40mm center to center. (Complete with spark arrester screen.)

636-141 503 47 69-01 503 59 92-05

Muffler / Exhaust For chain saw models: 61, 268 and 272. Also fits some older Jonsereds chain saw models: 625, 630 and 670. This is an aftermarket muffler. Mounting bolts holes are on 40mm centres. NOTE 1: This muffler is a NON DF version NOT US Forest Service approved.

636-146 501 81 68-01Muffler / ExhaustFor chain saw models: 281 and 288. Mounting bolts holes are on 46mm centres. NOTE 1: This muffler is a NON DF versionNOT US Forest Service approved


16-18


C C


503 71 13-07Muffler / Exhaust For chain saw models: 394, 394 EPA, 395 and 395 EPA. Mounting bolts holes are on 52mm centres. NOTE 1: This muffler is a NON DF version NOT US Forest Service approved. (Also see our 636-149)

636-149 503 71 13-04

Muffler / Exhaust For chain saw models: 394, 394 EPA, 395 and 395 EPA. Mounting bolts holes are on 52mm centres. Note: Complete with spark arrester screen. (Also see our 636-148)

636-143 503 76 53-02503 76 54-02

Muffler / Exhaust For chain saw models: 362, 365, 371, 372. Mounting bolt holes are on 53mm centres Note: Complete with spark arrester screen. (Also see our 636-145)

636-145 503 76 53-01

Muffler / Exhaust For chain saw models: 362, 365, 371, 372. Mounting bolt holes are on 53mm centres Note: This muffler is a NON DF version NOT US Forest Service approved(Also see our 636-143)

623-033 501 52 25-04

Exhaust / Muffler GasketsFits Chain Saw models: 61, 66, 162, 266 and 266XP. (Also found on Jonsereds model 630).

560-191 501 55 14-01501 55 14-02503 54 39-01

Starter Handle For most Husqvarna Chain Saw models, as well as many Jonsereds Chain Saws.

135-204 501 48 54-02

Spark Plug Boot with spring (70 degree)For chain saw models: 36, 41, 42, 40, 45, 50, 51, 55, 61, 66, 136, 141, 140, 242, 246, 254, 257, 261, 262, 266, 268K, 272K, 288, 335, 340, 345, 346, 350, 351, 362, 365, 371, 371K, 372, 394, 395, 3120, 3120K. (Fits 5mm spark plug wire).


650-272 503 73 66-01

Sprocket Side Cover For chain saw models: 61, 266, 268 and 272.

650-275 537 03 35-01

Sprocket Side Cover For chain saw models: 362, 365, 371, 372, 385, 390 and 575. Note: Chain adjuster and rubber saw chain guard included as shown in picture.

655-255 503 15 18-01503 15 18-02 / 503 60 88-03

Starter AssemblyFor chain saw models: 50, 51 and 55. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, handle etc. Just needs to be bolted on. (Made of plastic)

655-272 501 61 55-71

Starter AssemblyFor chain saw models: 61, 266, 268, 268K and 272. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, handle etc. Just needs to be bolted on. (Made of plastic)

655-365 503 62 81-71

Starter Assembly For chain saw models: 362, 365, 371 and 372. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, handle etc. Just needs to be bolted on. (Made of plastic). Uses our 625-410 replacement starter spring.


16-19



C C


Starter Assembly For chain saw models: 281 and 288. (1989 thru 2009). This aftermarket assembly comes complete with housing, starter pulley, spring, rope, handle etc. Just needs to be bolted on. (Made of plastic)

655-250 506 38 56-11 / 506 38 56-12 506 38 56-13 / 574 36 20-01

Starter Assembly For concrete / cut quik saw models: K750 and K760. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, handle etc. Just needs to be bolted on. (Uses our 625-430 starter spring).

560-060 503 76 37-01 503 85 95-01

Starter Pawl (steel) For chain saw models: 362, 365, 371 and 372.

560-147Starter Pulley For Chain Saw model: 35.Measures: 8mm / .315” ID X 2-3/8” (60mm) OD X 1-1/4” Overall Height. 8 Tooth gear X 1-1/8” OD.

560-368 069313530 06 93-13

Starter PulleyFits chain saw models: 136 and 41. Dealers use it on Husqvarna model 41 Chain Saw. May fit other Husky saws? (4) cog pulley. NOTE: original Husky application is (6) cog.

560-241 505 30 37-75505 30 37-35

Starter Pulley For Chain Saw models: 51 and 55. Measures: 12.8 mm or 1/2” ID X 64.52 mm or 2.540” OD X 30 mm or 1.183” overall height.

560-238 501 79 44-01

Starter PulleyFor Chain Saw model: 242.Measures: 12mm ID X 2-9/16” OD X 1-5/16” HT (While Quantities Last)

560-182 501 52 07-01Starter PulleyFor Chain Saw models: 61, 66, 266 & 181 (old). Measures: 10mm ID X 2-7/8” OD X 1-11/32” HT

560-211 503 10 24-02Starter PulleyFor Chain Saw models: 61, 66, 266 & 181 (new). Measures: 14mm ID X 2-7/8” OD X 1-13/32” HT

560-253 503 10 24-03503 10 24-05

Starter Pulley (longer hub) For Chain Saw models: 268, 268XP and 272. Measures: 14mm ID X 2-7/8” OD X 1-9/16” HT

560-209 503 48 48-01Starter PulleyFits chain saw models: 281 and 288. Measures: 14mm ID X 2-7/8” OD X 1-5/16” HT

560-260 503 85 96-01503 87 63-01537 09 25-01

Starter PulleyFits Husqvarna chain saw models: 340, 345, 346, 350, 351, 353, 362, 365, 371, 372, 385, 390, 445, 455 and 460. Also fits Jonsered chain saw models: 2141, 2149. Size: 12.2 mm ID X 68.3 mm OD X 27.7 mm overall height.

560-210 506 25 81-02Starter PulleyFits Concrete / Quik Saw models: K650 and K950. Measures: 14mm ID X 2-7/8” OD X 1-9/16” HT

560-242 506 01 64-01 537 20 19-01

Starter Pulley For Chain Saw models: 40, 45, 49, 240, 245, 334T, 335XPT, 336, 338 and 339. Measures: 13 mm or .510” ID X 65.25 mm or 2.566” OD X 29 mm or 1.14” overall height.

625-400 501 52 04-01Starter Spring For chain saw models: 61, 61 Rancher,66, 162, 181, 266, 266 XP, 268 & 272.

625-401 501 40 22-01

Starter SpringFor chain saw models: L65, 77, 160,180, 280, 285, 380 and 480.






16-20


C C


501 46 04-02501 46 06-01

Starter SpringFor chain saw models: 36R, all 40 series, 44, 45, 140, 165R, 240, 244, 340 and 444.

625-403 501 20 13-01

Starter SpringFor chain saw models:1100, 2100 and 2101.

625-404 501 76 31-01Starter SpringFor chain saw models: 41, 50, 50 Rancher, 51 and 55. Note: Will work on chain saw models: 340, 345, 346, 350, 351, 357, 359 if you re-use the original starter spring case - You will have to make a slight adjustment to the outside spring hook. (This spring is NOT an exact replacement for the Original Husqvarna# 537 09 31 01)

625-405 501 63 02-01501 63 01-01

Starter SpringFor chain saw models: 42, 133, 154, 242 & 246. Will also work in models: 254, 257, 261 and 262. (Spring comes in a metal band and DOES NOT include the plastic case / retainer

625-325 501 70 67-01

Starter SpringFor chain saw models: older 34 and 35. (spring in metal band)

625-406 503 13 50-01Starter SpringFor chain saw models: 356, 394, 395, 3120 and K12506.

625-407 503 85 99-01

Starter SpringFor chain saw models: 333, 335, 340, 345, 346, 350, 351, 353 (older style smaller). Spring is in a metal band, OD= 57mm approximately.Note: Just because this part is listed for a certain model doesn’t mean it will fit every saw ever made with that model number. Please see the image& OEM# to help determine if it is the correct part for your application.

625-410 503 78 72-01Starter Spring For chain saw models: 362, 365, 371 and 372. Spring is in a metal band, OD= 63mm approximately. Replacement starter spring for our 655-365.

625-411 501 52 01-02

Starter Spring For chain saw model: 288

625-430 506 25 89-01

Starter Spring For Concrete Saw / Cut Quik Saw models: K750, K760, K960 and K970.

625-408 537 09 31-01

Starter Spring For chain saw models: 340, 345, 346, 350, 351, 353, 357, 359. (newer style - larger diameter). Jonsereds chain saw models: 2149, 2159, CS2141, CS2145, CS2150, CS2152, CS2153, CS2156 and CS2159. Spring is in a plastic cage, Spring OD = 67mm / 2-5/8” approximately. Note: Also see our smaller OD spring 625-407.

654-148 501 62 90-03Tube Handle For chain saw model: 242. .....................................................

654-151 501 87 29-07For chain saw models: 50, 51, 55 and 254......................................................

654-138 501 53 45-02 501 53 45-03

For chain saw models: 61, 66, 162, 266, 266 XP, 268, 268 XP and 272......................................................

654-152 501 80 75-05For chain saw model: 281.

705-574T-WrenchFits chain saw model: 32, 36,38, 40, 44, 50, 51, 55, 61, 66,162,262, 266, 268, 281, 285, 288, 298, 380, 444, 480, 2100, 2102, 3120 & most other models. Size: A= 7”, B= 1”, C= 1”. Bar= 1/2” (13mm), Plug= 3/4” (19mm)

705-592 Carlton# 41C1319T

T Wrench / ScrenchUsed on Husqvarna and Stihl cut quik / cut off / concrete saws. Fits Husqvarna concrete saw models: K960 an d K970. Size: 1/2” (13mm) Bar Nut X 3/4” (19mm) Spark Plug X (B = 1-3/4”) + (C = 1-1/4”) = 3” total with a 7-3/4” long handle. T27 Torx End.

16-21



C C

Part# O.E.M Application Part# O.E.M Application605-710 71752Air FilterFits ICS Concrete / Cut off Saw models: 603GC, 613GC, 633GC and 680GC. Size: 3-7/8” OD X 2-3/8” ID X 3-1/4” HT. Same as our 605-709 except higher.

605-711 73336Pre FilterFor our 605-710 air filter. Fits ICS Concrete / Cut off Saw models: 603GC, 613GC, 633GC and 680GC. Size: 2-3/8” bottom OD X 2-1/16” top OD X 2-9/16” HT.

592-106 505375Crankshaft Bearing Fits ICS concrete saws, Size: 15mm (37/64”) ID X 35mm (1-3/8”) OD X 11mm (7/16”) HT(Bearing# 6202 - open both sides)

593-103 73209Crankshaft bearing ICS models 613GC, 633GC and 680GC; Size: 17mm ID X 40mm OD X 12mm HT.(Bearing# 6203/C3) Open both sides.

JONSEREDS605-173 501 80 71-01

501 80 71-05Air Filter For Chain Saw model: 630

605-062 503 81 45-03Air Filter For chain saw models: 2063, 2071, 2163 and 2171. Nylon mesh style.Size: 3-5/8” L x 2-7/8” W x 1-5/8” HTNote: Picture shows front and back views for reference

605-060 537 02 40-03

Air Filter (Twist on) For chain saw models:2141, 2145, 2149, 2150 and 2152. Air filter attaches by simply twisting on the carburetor manifold. Note: Some 346 and 353 models use a steel snap to connect.

646-154 503 74 44-01

Clutch Assembly For chain saw models: 2063, 2065, 2163, 2165, 2071 & 2171. Measures: 3.057” OD X 0.471” Thick.

646-155 503 70 15-02

Clutch Assembly For chain saw models: 820, 830, 920, 930, 2094 & 2095. Measures: 3.045” OD (77mm) X 0.542” (13.90mm) Thick.

646-113 501 77 85-01

Clutch Assembly Fits chain saw models: 625, 630 and 670. Measures: 3.057” OD X 0.512” Thick. (Also see our 646-153 newer style).

651-175 537 07 12-01

Chain Adjuster Assembly Found on model: 2159 chain saw.(Includes part#’s 503869101 and 503885401);

570-283 537 15 73-02

Cylinder Assembly (47mm) Fits model: 2159. Displacement: 59cc; Stroke: 34mm.

570-286 503 69 10-73503 93 90-03

Cylinder Assembly (48mm) Fits chain saw models: 2065 and 2165.

570-287 503 62 64-72503 62 64-73503 93 90-05503 93 93-71503 93 93-72503 96 52-71

Cylinder Assembly (50mm) Fits chain saw models: 2071 and 2171.

2159

2065 & 2165

2071 & 2171

ICS JONSEREDS continued

16-22


C C

Part# O.E.M Application Part# O.E.M Application572-801


572-705 537 15 72-02

Piston Assembly (47mm) Fits chain saw model: 2059 and 2159.

572-499 503 53 90-02

Piston Assembly (48mm) For chain saw models:625 and 630. Direct replacement for the original (48mm) bore Jonsereds cylinder assembly.

572-714 503 69 13-71

Piston Assembly (48mm)Fits Chain Saw models: 2065 & 2165. (replaces our old# 572-806)

572-524 501 65 94-03

Piston Assembly (50mm)For model: 670.

572-718 503 28 90-42503 69 12-71503 69 14-71503 93 92-71

Piston Assembly (50mm) Fits Chain Saw models: 2071 and 2171.

572-807 501 65 88-03

Piston Assembly (50mm) Fits chain saw model: 670. Includes: Piston, Piston pin, Retainer clips and ring.

572-715 503 60 98-02503 60 98-03

Piston Assembly (52mm)Fits chain saw model: 670. NOTE: For 50mm piston assembly see our 572-807.

572-717 537 16 98-71

Piston Assembly (54mm) Fits chain saw model: 2186. Note: Piston Rings = 1.2mm thick

572-812


572-721 503 46 02-02

Piston Assembly (56mm)Fits chain saw model: 2095. Overall Height = 49mm, (1mm) higher then our 572-722Note: Piston rings = 1.5mm thick

572-722 537 13 76-71

Piston Assembly (56mm)Fits chain saw model: 2095. Note: Piston Rings = 1.2mm thick

574-206 503 28 90-02

Piston Ring Set (40mm X 1.5mm)Fits chain saw model: 2040.

574-212 503 28 90-05

Piston Ring Set (42mm X 1.5mm)Fits chain saw model: 2045.

574-230 503 28 90-29

Piston Ring Set(47mm X 1.5mm) Fits chain saw model: 2063 & 2163.

574-157 501 20 56-02503 28 90-15

Piston Ring only (48mm X 1.5mm) Fits chain saw model: 630For our 572-499 piston assembly.

16-23

JONSEREDS continued JONSEREDS continued


C C

Part# O.E.M Application Part# O.E.M Application574-137 503 28 90-17Piston Ring only (50mm X 1.5mm) Fits chain saw model: 670For 572-524 piston assembly

574-254 503 28 90-22Piston Ring Set (54mm X 1.5mm) Fits chain saw model: 2083.

570-003 503 71 53-01Decompression Valve For Chain Saw and Concrete saw cylinder assemblies. Overall Length: 1-7/16” - Blue knob with 2 holes in nut.

570-005 503 665 601

Decompression Valve (Blue Knob) For Chain Saw and Concrete saw cylinder assemblies. Fits Husqvarna, Jonsereds and Partner models: K1250 etc. Overall Length: 1-7/8” - Blue knob with 2 holes in nut. Similar to our 570-003 but with a longer main body.

623-820 501 51 22-02

Head / Base GasketFits models: 630 and 670.

623-822 503 96 15-01Head / Base Gasket onlyFits chain saw models: 362, 365, 372, 372 and 375; also fits Jonsereds models: 2065, 2071, 2162 and 2171.

640-243

Gasket SetFits chain saw model: 630. (Includes oil seals)

551-107 501 56 45-01Fuel CapFor chain saw models: 625, 630 and 670.

600-185 503 90 14-01941 14 60-1

Electronic IgnitionFor chain saw model: 630

600-164 501 51 61-01501 51 61-02501 61 75-01

Electronic Ignition Fits chain saw models: 625, 630 & 670.The electronic ignition component is connected with the ignition coil to achieve full ignition. This type of ignition module utilizes transistor switches for magnet activation.

610-040 363400Fuel Filter - FeltFuel Filter found on many Jonsereds chain saw models. Measures: 3/4” L X 1/2” ID X 3/4” OD

560-191 501 55 14-02

Starter HandleFor most Jonsereds Chain Saw models.

560-147

Starter PulleyFor Chain Saw model: 361. (Frontier)Measures: 8mm / .315” ID X 2-3/8” (60mm) OD X 1-1/4” Overall Height. 8 Tooth gear X 1-1/8” OD.NOTE: For other Jonsereds “Starter Pulleys” see our Husqvarna listings for more information

625-400 501 52 04-01

Starter Spring For chain saw models: 625, 630, Super & 670.

625-450 504 21 26-01

Starter Spring For chain saw models: 66E, 70E, 80, 90, 111 Super, 621, 801, 910E, 910EV and 920.

625-451 504 21 26-02

Starter SpringFor chain saw models: 49SP, 50, 51, 52, 52E & 521EV.

625-452 504 21 00-17

Starter Spring For chain sawmodels: 451E and 451EV.

625-455 504 21 26-06

Starter Spring For chain saw models: 450, 455, 510SP, 520SP, 525 and 535.

625-325 507 10 00-73

Starter Spring For chain saw models: M36, 361, 361E, 365, 370 and 380.



16-24



C C


Starter Spring For chain saw models: 490 and 590.

625-404 501 76 31-01

Starter SpringFor chain saw model: 2041.

Note: Will work on Husqvarna chain saw models: 340, 345, 346, 350, 351, 357, 359 if you re-use the original starter spring case - You will have to make a slight adjustment to the outside spring hook. (This spring is NOT an exact replacement for the Original Husqvarna# 537 09 31 01)

625-408 537 10 93-101

Starter Spring For chain saw models: 2149, 2159, CS2141, CS2145, CS2150, CS2152, CS2153, CS2156 and CS2159. Spring is in a plastic cage, Spring OD = 67mm / 2-5/8” approximately.

636-145 503 76 53-01

Muffler / Exhaust For chain saw models:2063, 2065, 2071, 2163, 2165 and 2171. Exhaust mounting holes are 53mm center to center. This muffler is a NON DF version NOT US Forest Service approved. (Also see our 636-143)

636-143 503 76 53-02503 76 54-02

Muffler / Exhaust For chain saw models: 2063, 2065, 2071, 2163, 2165 and 2171. Exhaust mounting holes are 53mm center to center. Comes with spark arrester. (Also see our 636-145)

636-148 503 71 13-07

Muffler / ExhaustFits chain saw models: 2094 & 2095. Mounting bolts holes are on 52mmcentres. NOTE 1: This muffleris a NON DF version NOT US Forest Service approved. (Also see our 636-149) Front and back images shown for reference

636-149 503 71 13-04

Muffler / ExhaustFor chain saw models: 2094 & 2095. Mounting boltsholes are on 52mm centres. Note: Complete with spark arrester screen. (Also see our 636-148) Front and back images shown for reference.

705-574

T-WrenchFits chain saw models: 510, 525, 530, 535, 630,670 and most other Jonsereds models. Size: A= 7”, B= 1”, C= 1”. Bar= 1/2” (13mm), Plug= 3/4” (19mm)

705-600

T-WrenchFits chain saw models: 77, 90, 621, 820 and 920.Size: A= 7”, B= 1-1/8”, C= 1-1/8”. Bar= 19/32” (15mm), Plug= 3/4” (19mm)

For MAKITA - See DOLMAR / MAKITA

McCULLOCH605-204 214224 / 216905

61460 / 91460Air Filter Fits models: 110, 120, 130, Mini Mac and Eager Beaver. Size: 2” OD X 7/8” HT

605-339 213883 / 215803300385

Air Filter Fits Chain Saws and Blowers. Models: 300 and 385. Felt with rubber seal. Size: 4” L X 2-13/16” W

605-215 89072 / 92410

Air FilterFits Chain Saw model: 510 Size: 3-1/4” L X 3-1/4” W

16-25



C C

Part# O.E.M Application Part# O.E.M Application605-253 68685

91458Air Filter Fits chain saw model: Power Mac. Size: 3” L X 2-1/4” W

605-216 55498Air Filter Fits chain saws models:D44, 14, 150, 160 and all Super series, Super 250 & 550. Size: 5-3/8” L X 5-1/4” W

605-261 21568185387

Air FilterFits chain saws models: 800, 805 and 850 Size: 5-3/8” L X 5-1/8” W

605-246 2166856992292420

Air Filter Fits chain saws models: 10-10 and 700 series Size: 4-3/8” L X 4-1/8” W

605-212 21545632200194970

Air FilterFits chain saws models: 310, 320, 330 & Eager Beaver 2.1 Size: 3-3/16” L X 2-11/16” W

605-238 214226 / 95213Air Filter Fits chain saws models: 600, 610 series and Eager Beaver 3.7 (Raised centre) Size: 4-3/8”L X 4-1/4” W

670-104 110676Bar NutFor chain saw model: Mini- Mac 600 series. Size: 1/4”-28

670-105 120029Bar Nut For chain saw model: Mini Mac 300 series. Size: 6.3mm X 1.0 thread

670-101 213169

Bar NutFits Husqvarna, Jonsereds, McCulloch etc. McCulloch models: 600, 605, 610 and 650. Size: 8mm X 1.25 thread. For 13mm T-wrench



651-141Chain Adjuster For McCulloch chain saw model: Mac 6.

651-243 110907 / 6865684929 / 90658

Chain Adjuster For chain saw model: Mini Mac 100 and 300 series

651-399 102115 / 105603110590 / 11095091982 / 94362

Chain Adjuster For chain saw model: 600 series.

621-120 83223Clutch Spring For chain saw models: 10-10, Mac 7-10, 55, 60 and SP 81.

621-121 51468AClutch Spring For chain saw models: Super 250 and Super 550.

610-048 63932Fuel FilterFound on many chain saw models. Made of felt. Measures: 1” L X 3/4” OD

613-601 21698549422 / 93720

Fuel Filter - In TankFuel Filter for all McCulloch Mini Chain Saw and Trimmer models using 3/32” thru 1/8” ID fuel lines.Measures: 1-1/4” long X 1/2” diameter.

610-238 215708301011 / 64848

Molded FuelLine for chain saw model: 10-10. Measures: 6-1/8” overall length

600-935 Walbro# AM-35

Electronic ModuleFor chain saw models: Eager Beaver and Super Airstream V. (Original WALBRO module) (Made by SEM / WALBRO)

502-119 Phelon# 08133-04

Coil and Core (Armature)For chain saw models: MINI. For older style with points & condensor. (Original PHELON coil) (Made in the U.S.A.)


16-26

McCULLOCH continued McCULLOCH continued


C C

Part# O.E.M Application Part# O.E.M Application550-111 89322Fuel CapGas Cap for chain saw models: Pro 10-10 and Pro Mac 60 series.

551-111 87270Oil CapFor chain saw models: Pro 10-10 and Pro Mac 60 series.

625-200 51665Starter SpringFor chain saw models: 1-40, 50,60, 70, 80, 200, 300, 400, 500, 600, 700, 800, D-44, PM-105, SP-125, 550 and Super 797.

625-201 68626

Starter Spring For chain saw models: Mac 1-10, 2-10, 3-10, 4-10, 5-10E, 6-10, CP 55, 70, 10-1C and 52-10A.

625-202 83078Starter SpringFor chain saw models: Mac 110, 115, 120, 130, 140, Mini Mac 6, 25, 30, 35, Power Mac 6, Pro Mac 55, 510, Super Pro 40, 310, 320, 330, 340 & Titan 7.

625-203 83334 / 87680Starter Spring For chain saw models: Pro Mac 10-10, 55, 60, 555, 570, 610, 650, 700, 800, 805, 850, 1010S, 5700, 8200,Super Pro 60, 70, 80, 81 and Model 7-10A.

625-427 32107

Starter Spring For chain saw model: 1000.

OLEO MAC 625-675 50 00132Starter Spring For chain saw models: 250, 251, 251E, 251 Super, 252, 254 and early model 264.Note: Comes in a plastic case not shown

625-676 40 0013240 95034

Starter SpringFor chain saw models: 234, 240, 241, 244, 264F - Deluxe, 350, 355A, 935D, 941, 942, 945, 946, 950, 951 & 970.

625-500 60 0013261 00963

Starter SpringFor chain saw models: 260, 261, 271, 272, 284, 460AS, 480AS, 481, 482 and 482 MP.

PARTNER605-338 506 22 42-01

531 03 14-97Air FilterFits Concrete / Cut-off Saws models: K650 Active and K700 Active. Size: 4-3/4” L X 3-3/8” W X 2-1/8” HT.Note: Top and Bottom images shown for reference.(For Pre Filter see our 605-239).

605-239 506 22 63-01999810

Pre filterFits chain saw models: K650 Active and K700. (3) layer foam filterSize: 7-7/8” L X 4-1/2” W X 3/4” HT

605-378 544 18 16-01

Air FilterPanel Air filter for Concrete / Cut Quik Saw model: K750. (For use with our 605-377 pre filter)Base Size: 4-15/16” L X 4-1/2” W X 1-3/8” HT.

605-377 506 36 71-01

Pre filter For Concrete / Cut Quik Saw model: K750. (For use with our 605-378 air filter) Size: 7-5/64” L X 5-1/2” W X 13/16” HT.

605-440 506 23 19-01506 25 59-32

Pre Filter(3) Layer foam filter. Fits chain saw models: K950 Active & K960 Cut Quik saws. Size: 10-3/8” L X 5-1/4” W X 3/4” HT approx.(Also see our 605-438 Air Filter)

605-438 506 23 18-01506 23 18-02

Air FilterFits chain saw models: K950 and K1250 Active Cut Quik saws. Size: 6” L X 4-1/8” W X 2-5/8” HT

605-280 506 26 87-01

Pre filterFits Concrete / Cut Quick Saw models: K1250. (3) layer foam filter.Size: 10-5/32” L X 6-1/2” W X 13/16” HT.

16-27

McCULLOCH continued OLEO MAC continued


C C


Air Filter For concrete / cut quik saws. For models: K1200 and K1200 Mark II. Size: 5-7/8” OD X 4-1/8” ID X 2-1/2” HT

875-724 506 07 05-03

Drive belt (cogged)For concrete / cut quick saw model: K950 with 12” and 14” blades. Size: 3/8” W X 34-1/2” L

875-712 506 29 67-02 544 90 84-02

Drive belt (multi rib)For concrete / cut quick saw model: K750. Size: .551” W X 32” L (6 rib, polyester cord construction)

875-725 506 07 05-04 506 34 74-24

Drive belt (cogged)For concrete / cut quick saw model: K950 Active with 16” blades. Size: 3/8” W X 36” L

875-711 506 03 30-31 506 27 67-41

Drive belt (cogged)For concrete / cut quick saw model: K650 Active, K650 Active II and K700 Active II Size: 1/4” W X 31-1/2” L

875-713 506 07 05-06

Drive belt (cogged)For concrete / cut quick saw model: K650 Active III & K700 Active III cut off saws.Size: 3/8” W X 31-1/2” L

875-726 506 07 05-07

Drive belt (cogged)For concrete / cut quick saw model: K1250 Active cut off saws. Size: 3/8” W X 39-1/2” L

670-101 503 22 00-01

Bar NutFits chain saw models: R16, S50, S55, P55, P70 and P100. Size: 8mm X 1.25 thread. For 13mm T-wrench

651-142 230902267650

Chain AdjusterFor chain saw models: R16, S50, S55, P55, S65, P70 and P100.


621-127 294112

Clutch SpringFor chain saw model: R16.

621-156 505 29 31-66

Clutch SpringFor chain saw models: 400, 500 and 5000.

621-115 503 14 51-01

Clutch Spring For models: 281, 288, 3120, 334T, 335XP, 336, 338, 339, 385, 390, 394, 395, K960 and K1250. Overall Length: 1-1/8” X 7/16” OD.

570-268 506 09 92-12

Cylinder Assembly (50mm)Fits concrete saw models: K650 (new style), Super MKII and K700.

570-270 506 38 61-71

Cylinder Assembly (51mm)Fits concrete / cut quik saw model: K750.

570-271 506 15 55-06

Cylinder Assembly (56 mm)Fits concrete / cut quik saw model: K950.

570-269 506 29 427-1A

Cylinder Assembly (60mm) Fits concrete / cut quik saw model: K1250

K650 Cut off

K750

K950

K1250

16-28

PARTNER continued PARTNER continued


C C


Piston Assembly (48mm)For chain saw model: P650 and Partner concrete saw model: K650 (old style). Includes: domed piston and rings, piston pin and clips.

572-511 506 09 90-01

Piston Assembly (50mm)For concrete saw model: K650 (new style).

572-902

Piston Assembly (51mm)Fits concrete / cut quik saw model: K750.

574-157 505 26 60-48

Piston Ring (48mm)For chain saw model: P650 and Partner concrete saw model: K650 (old style)

574-137 503 28 90-17

Piston Ring (50mm)For Partner concrete saw model: K650 (newer style).

570-002 503 66 56-01503 71 53-01

Decompression Valve For Chain Saw and Concrete saw cylinder assemblies. Fits models: K650 and K700, Active I, II, III. Overall Length: 2” - Black knob with 1 holes in nut. Similar to our 570-004 but with different knob. (For plug only see our 570-001)

570-005 503 66 56-01

Decompression Valve (Blue Knob) For Chain Saw and Concrete saw cylinder assemblies. Fits Husqvarna, Jonsereds and Partner models: K1250 etc. Overall Length: 1-7/8” - Blue knob with 2 holes in nut. Similar to our 570-003 but with a longer main body.

640-360 506 38 53-05

Gasket SetFits Husqvarna / Partner cut quit / concrete saw models: K750 and K760.(Includes oil seals)


640-182

Gasket SetFits Chain Saw model: K-650 Active

640-186

Gasket SetFits Husqvarna / Partner cut quit / concrete saw model: K950. (Includes oil seals).

640-323

Gasket SetFor chain saw models: 500, 5000 and 5000 Plus. (Includes oil seals).

623-868 503 49 10-02503 49 10-01

Head / Base Gasket Fits Chain Saw model P650 and Concrete Saw model K-650 (both old and new), K700 Active I, II, III.

623-751 506 37 67-01

Head / Base Gasket For cut quik / concrete saw models: K750 and K760.

623-499 506 15 82-01

Head / Base Gasket For cut quik / concrete saw models: K950.

591-101 302333

Bearing - Piston Fits Chain Saw models R16, S50, P650 and Partner K650 concrete saw. (Size: 12mm X 16mm X 13mm)

551-116Oil CapFor chain saw models: R16, S50, S55, P55 and P70. Made of aluminum with screwdriver slot on top.

550-109 506 25 59-32

Fuel Cap For chain saw and concrete / cut quik saw models: K650 and K950.

650-122 340722

Sprocket Cover Partner Cover for chain saw models: R16, S50, S55, P55 and P70. Cast aluminum cover (yellow)

16-29

PARTNER continued PARTNER continued


C C


Starter SpringFor chain saw models: 500, 5000 and 5000 Plus.

625-427 505 29 51-08295108

Starter SpringFor chain saw models: R16, 18, 22, 30, 40, F55, K16, 20, 65, 650, 850, 1200, P55, 70, 100, 7000.

625-325 504 35 27-05

Starter Spring For chain saw models: MINI P, P2, 3, 4, 330, 340, 350, P11 and P12.

625-430 506 25 89-01

Starter Spring For Partner / Husqvarna Concrete Saw / Cut Quik Saw models: K750, K760, K960 and K970.

655-250 506 38 56-12

Starter Assembly For concrete / cut quik saw model: K750. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, handle etc. Just needs to be bolted on

POULAN605-428 23791

530 023791

Air FilterFits chain saw models: Micro XXV, Micro 25, 180, 200, 205, 225, 235, 236, 1800, 2000, 2100, 2300, 2350 and 2400. Size: 2-5/8” L X 1-1/2” W X 1” HT

605-436 23369530 023369

Air FilterFits chain saw models: 25 and 25DASize: 3-3/8” L X 1-5/8” W X 1-1/4” HT

605-410 2586530 002586530 02586

Air FilterFits chain saw model: 361 Size: 4-1/8” L X 3-1/2” W

605-515 530 037793

Air Filter Fits chain saw models: 1950, 2050, 2075, 210, 2150, 2175, 2250, 230, 2450, 2550, 260, Pro 221, 221LE, 2375, Wild Thing, 1900, 2350, 2055, 220, 225 and Woodsman. Size: 3-1/4” L X 2-1/2” W X 3/4” HT

605-486 036141530 036141545 057701

Air FilterFits chain saw models: 2200, 2500, 2600, 2700, 2750, 2775, 2900, 3050, PP4620AVHD, PP4620AVL and Poulan Pro 255, 295, 310 and 315.Size: 3” L X 2-3/4” W X 7/8” HT

605-402 24548 / 20913530 024548952 014129

Air FilterFits chain saw models: 3400 and 3700. Size: 3-7/8” L X 2-5/8” W X 1” HT

646-129 93919ClutchFor many small Poulan chain saw and Poulan / Weedeater Trimmer models. Measures: 2-3/8” OD, steel washer included.

621-132

Clutch SpringFor chain saw models:201, 221, 361, 401 and 451.

651-150 530 015134530 015135530 023492

Chain AdjusterFor chain saw models: Micro XXV, Micro XXV Deluxe, Micro 25, Micro 25 Deluxe, 1800 2000, 2300 and 2350.

651-151 15134 / 15135 / 23492530 015134530 023492

Chain Adjuster For chain saw model: 250.

651-375 15385 / 23064530 015385530 023064

Chain AdjusterFor chain saw models: 3400 and 3700.

651-377 069611530 069611

Chain AdjusterFor chain saw models: 210, 230, 260, 2050, 2075, 2150, 2175, 2250, 2450 and 2550.


16-30

PARTNER continued POULAN continued


C C


Cylinder AssemblyFits chain saw models: 220, 221, 260, 351, 370, 390, 420, 1950, 2050, 2150, 2175, 2250, 2375 Wild Thing, 2450, 2550. Includes: cylinder,piston and rings, piston pin & clips. (Cylinder Bore: 41 mm). This cylinder kit seems to be listed as fitting several Poulan chain saw models varying from 33 cc thru 42 cc. Please see picture for more clarification. Dealers have told us this kit replaces Poulan OEM#’s 530069606 and 530047127.

610-022 23364530 091878

Fuel Filter Replacement felt filter for our 610-014 in-tank fuel filter. Fuel Filter for many Poulan chain saw models. Measures: 1” Long X 1/4” ID X 9/16” OD.

610-030 34032530 034032

Fuel FilterReplacement felt filter for our 610-006 in-tank fuel filter. Fuel Filter for many Poulan chain saw models. Measures: 1” Long X 7/16” ID X 13/16” OD.

610-345 530 023166 530 026119

Duck Bill Valve For Homelite chain saw models XL, XL-2 and Super 2. Duck Bill Valve - Fits Homelite Trimmers and Chain Saws. Measures: .100” ID X .201” OD X .25” L

125-245 530 014347 / 952 701583530 010729 / 952 701567

Gas CapFor chain saw models: 180, 190, 1800, 185, 2000, 2300AV, 2300CVA, 2350CVA and 5500.Measures: 1-1/2” diameter.

550-151 530 071266501 819602

Fuel CapFor chain saw models: 234, 238 and 365.

600-915 Walbro#MA-15

Electronic Ignition Module For Poulan / Weedeater chain saw “CSI” models. (Original WALBRO / SEM module)



630-038 2501

Starter CupFor chain saw model: 25D. Made of aluminum

560-101 4229Starter Dog / Starter Pawl.Found on many older chain saws using an aluminum starter cup. Size: Dog width: 1/2” with a 3/8” ID.

610-034 530 023877

Fuel Line FittingFits chain saw models: 180, 1800, 180C, 1800 Super, 190, 2000, 210, Micro XXV and S23. Arbor Pro gas saws.

610-032 530 010897 / 530 014362 530 014815 / 530 023364 530 047004530 095643 530 095646 530 095649

Fuel FilterFits chain saw models: 2025, 2050, 2350, 2775 & FL 1500. Size: 9/16” OD X 1-5/8” L.

660-060 530 069957530 071259

Oil Pump Fits chain saw models: 1950 thru 2550, 211, 220 & 260 Pro.

560-368 530 06931369313

Starter PulleyFits chain saw models: 2200, 2500, 255, 2600, 2750, 2900, 295, 3050, 310, 315. Starter Pulley for Poulan saws - Dealers have used it on Husqvarna model 41 Chain Saw. May fit other Husky saws? (4) cog pulley. NOTE: original Husky application is (6) cog.

145-516

Starter Rope AssemblyFor chain saw models: 25D and also 180 and 190. Rope length 21”, plastic knob fastened to rope end.

625-152 530 04201242012

Starter SpringFor chain saw models: 245, 305, 306, 345, 2000 and 2300

16-31

POULAN continued POULAN continued


C C

Part# O.E.M Application Part# O.E.M Application625-442 530 027531

Starter SpringFor chain saw models: 2025, 2050, 2075, 210, 2150, 2175, 2250, 230, 2350, 2450, 2550 and 260, 285, 295, 305, 310, 315 and 335

625-157 530 04205142051

Starter Spring For chain saw models: 3400 and 3700. Starter Spring for Sears / Roper / AYP chain saw models: 358-354810, 358-354830 (3.4, 3.7 CU. IN. Poulan)

625-101 4262

Starter SpringFor Lombard chain saw models: 42 series, Lightning and Comango. Starter Spring for Poulan chain saw models: 360, 361 and 400.

REMINGTON605-501 67863

Air FilterFits chain saws. Made of wire mesh and felt material. Size: 1-13/16” L X 1-3/16” W

605-533 080604Air Filter Fits chain saws. Made of wire mesh and felt material. Size: 2-3/4” L X 7/8” W

605-523 66241Air FilterFits chain saw model: Mighty Mite (Large version). Made of felt material. Size: 3-9/16” L X 3-1/4” to 4-1/16” W (bottom)

605-553 65071Air FilterFits chain saw model: SL9 and SL9 deluxe. Made of felt material. Size: 3-5/8” L X 3-5/8” W.

560-101 60832

Starter Dog / Starter Pawl. Found on many older Remington chain saws using an aluminum starter cup. Used on older Poulan, Homelite, Remington and Stihl chain saws. Remington models: Pl-4, Sl-4A, Bantam etc. Size: Dog width: 1/2” with a 3/8” ID.

560-102

Starter Dog WasherThis is a fibre washer used on older Fairbanks Morse, Remington etc. chain saws that used a starter dog assembly and aluminum starter cup.

FOR SACHS DOLMAR - SEE “DOLMAR /

MAKITA” SECTION.SEARS / ROPER / AYP605-907 9163H

Air FilterFits AYP / Sears/ Roper Chain Saw. Sears model 3.7 cubic inch Size: 3-7/8” L X 3-5/8” W

605-914 643A1289918R

Air FilterFits chain saws. Size: 4-1/4” L X 2-1/2” W

625-157 42051

Starter SpringFor chain saw models: 358-354810, 358-354830 (3.4, 3.7 CU. IN. Poulan)

SHINDAIWA605-319 38010-82581

Air filter Fits Cut off saws, models: EC7500 and EC7600. (includes foam pre filter)Size: 7” L X 4” W X 2” HT

625-900 22104-7530022104-75310

Starter SpringFor chain saw models: 305, 345, 346, 350, 355, 405, 406, 407, 410, 415, 416,440, 450, 451, 480, 485 and 500.

625-901 22100-75310

Starter SpringFor chain saw models:415 and 450 (older models)


16-32

POULAN continued REMINGTON continued


C C

Part# O.E.M Application Part# O.E.M Application625-325 F315882


625-427 295108


SOLO (Homelite 47/54)

625-826 26 00 166Starter Spring For chain saw models: 610, 611, 616, 647 and 654. (Fits HOMELITE Saw models 47 and 54)

625-828 26 00 167

Starter SpringFor chain saw models: 635 and 642.

STIHL605-708 1108-120-1600

Air FilterFits chain saw models: 08 and 08S

541-103 1108-140-1000Air filter capFits chain saw models: 08 and 08S. (For use with our 605-708 air filter)

605-719 1120-120-16001120-124-0800

Air filter Fits chain saw model: 009, 010, 011. Size: 3-7/8” L X 2-5/8” W

605-717 1130-124-0800Plate filter Fits chain saw models: 017, 018, MS170 and MS180. Size: 3-1/2” L X 2-9/16” W approximately.

605-687 1123-120-16131123-120-1612

Air FilterFits Chain Saw models: MS210, MS230 and MS250. Size: 3-5/8” L X 1-3/16” W X 1-3/8” HT.

605-679 1127-120-162111127-120-1620

Air Filter Fits chain saw models: 029, MS290, MS310 and MS390. Size: 4-9/16” L X 2-5/8” W X 1-1/2” HT. (Top and Bottom pictures shown (1) air filter only)

605-741 1121-120-1617

Air Filter Fits chain saw models:026 and MS260. (Top and Bottom pictures shown (1) air filter only)

605-733 1118-120-16101118-120-16111118-120-1615

Air Filter Fits chain saw models: 028, 028 Super and 028 Wood Boss. Size: 3-1/2” L X 2-1/4” W X 3/4” HT

605-753 1125-120-16151125-120-1620

Air FilterFits older Stihl models: 034, 034 Super and 036. Fits older 034 chainsaws before Serial Number 1 45 945 205. Fits older 036 chainsaws before serial number X 32 622 639. This filter doesn’t have the compensator hole, and is too narrow for newer models 034 & 036. Please verify serial number first before purchasing. Size: 3-1/4” L X 2-7/8” W X 1-1/8” HT

606-138 1119-140-1903 1119-140-1905

Air filter coverAftermarket box cover for chainsaw model 038 series. This plastic piece often takes most of abuse from day to day use and fades in colour. Includes attachment nut and mesh screen.

605-071 1119-120-16101119-120-16111119-120-1615

Air FilterFits chain saw models: 038, 038 Super, Magnum and Wood Boss. Size: 4-1/8” L X 3-1/8” W X 7/8” HT

605-675 1110-120-1601

Air FilterFits chain saw model: 041. Made of wire mesh & felt material. Size: 4-1/4” L X 4-1/8” W

16-33

SKIL STIHL continued


C C

Part# O.E.M Application Part# O.E.M Application541-106 1110-140-9500Air filter cap Fits chain saw models: 041, 051 and 070. (For use with our 605-675 / 605-676 / 605-686 air filters)

605-676 1111-120-1601Air FilterFits chain saw models: 051 and 076. Made of wire mesh and felt material. Size: 5” L X 4-1/4” W

605-683 1113-120-16021113-120-16031113-120-1612

Air Filter Fits chain saw models: 031 and 032. Size: 3-1/8” L X 2-5/8” W X 15/16” HT

605-744 1120-120-1610Air FilterFits chain saw models: 044 and 046 (older style) Nylon mesh material (Orange in colour)

605-735 0000-120-1653 / 0000-120-1654

Air FilterFits chain saw models: 044, 046, 064, 066, 088, MS440, MS441, MS460, MS640, MS650, MS660 and MS880. Felt cloth outer wrap with a foam filled interior. Designed for oil-less use. Size: 4-3/16” L X 3-1/8” W X 1-3/4” HT

605-764 1122-120-16151122-120-1620

Air Filter Fits chain saw model: 064 (older style) Nylon mesh material

605-686 1106-120-1602

Air Filter Fits chain saw model: 070. Made of wire mesh and felt material.Size: 6-3/8” L X 4-1/8” W X 1/8” HT

605-725 4201-140-1801

Air FilterFits Concrete / Cut off Saw models: TS350 and old style TS510 / TS760Inner filter - 2 bolt mount style (Inner filter for our 605-709)



605-709 4201-140-18054201-141-0300

Air Filter Fits Concrete / Cut off Saw models: TS350, TS350AVE, TS360, TS510 and TS760. Size: 3-7/8” OD X 2-3/8” ID X 2-7/8” HT (Also found on Sachs Cut off saws)

605-691 4201-141-0310

Air Filter Wrap Fits Concrete / Cut off Saw models: TS350, TS360 and TS510 / TS760. Felt wrap with stitched elastic for tight seal. (Pre filter for our 605-709)

605-055 4201-140-1802

Inner Air Filter Fits Concrete / Cut off Sawmodel: TS360. Inner filter - centre bolt mount style.(Inner filter for our 605-709)

605-336 4223-141-0300

Air FilterFits Concrete / Cut off Saw model: TS400 (air filter). Size: 5-3/8” L X 3-3/8” W X 1-15/16” HT. (Paper element with soft foam seal)

605-332 4223-140-03004223-140-1800

Air FilterFits Concrete / Cut off Saw model: TS400 (secondary filter). Size: 4-5/8” L X 2-11/16” W X Pipe: 1-1/8” OD X 7/8” HT

605-337 4223-141-0600

Air Filter Fits Concrete / Cut off Saw model: TS400 (pre filter). Size: 5” L X 3-1/8” W X 13/16” HT, Centre hole 5/16”, Offset hole 3/16” ID. (3) layer foam

16-34

STIHL continued STIHL continued


C C

Part# O.E.M Application Part# O.E.M Application605-348 4221-140-4400

4221-141-0300

Air Filter Fits Stihl Concrete / Cut off Saw models: TS460 / TS510 / TS760 (air filter). Size: 4-1/2” OD X 2-1/16” ID X 2-1/4” HT. (Use with our 605-343 & 605-346)

605-343 4221-140-1800

Air Filter Fits Stihl Concrete / Cut off Saw models: TS460 / TS510 / TS760 (inner filter). Size: 1-7/8” OD X 1-11/16” ID X 1-11/16” HT. (Use with our 605-348 and 605-346)

605-346 4221-141-0310

Air FilterFits Stihl Concrete / Cut off Saw models: TS460 / TS510 / TS760 (pre filter). Made of felt material.(Use with our 605-348 and 605-343)

605-692 4224-141-03004224-141-0300A

Air Filter Fits Concrete / Cut off Saw models: TS700 and TS800. Size: 5-1/2” L X 4-1/16” W X 1-3/4” HT. (Paper element with soft foam seal). Uses our 605-700 pre filter.

605-700 4224-140-1801

Air Filter Pre Filter (secondary filter)Fits Concrete / Cut off Saw models: TS700 and TS800. Size: 4-5/8” L X 3-1/4” W X 9/32” HT. For use with our 605-692 air filter.

Filter Kit for TS350 & TS510605-800 4201-140-1801

4201-140-18054201-141-0300 4201-141-0310

Air Filter (3) Piece Kit Fits Concrete / Cut off Saw models: TS350 and TS510


16-35

Air Filter Kit for STIHL TS360605-810 4201-140-1801

4201-140-18024201-141-0310

Air Filter (3) Piece Kit Fits Stihl Concrete / Cut off Saw model: TS360

Air Filter Kit for TS400605-820 4223-007-1010

4223-140-18004223-141-0300 4223-141-0600

Air Filter (3) Piece Kit Fits Stihl Concrete / Cut off Saw model: TS400. Kit includes: (1) 605-336, (1) 605-332 and (1) 605-337

Filter Kit for TS460, TS760605-840 4221-007-1002

4221-140-18004221-140-44004221-141-0310

Air Filter (3) Piece Kit Fits Concrete / Cut off Saw models: TS460 / TS760

Filter kit for TS410 and TS420605-850 4238-140-1800

4238-140-44014238-140-44024238-141-03004238-141-300B

Air Filter (2) Piece Kit Fits Concrete / Cut off Saw models: TS410 / TS420. (Includes (1) 605-559 pre filter and panel filter). The panel filter measures:5-3/4” L X 5-1/2” W X 1-3/4” HT approximately.

605-559 4238-140-1800

Air Filter Fits Stihl Concrete / Cut off Saw models: TS-410 and TS-420. Size: 5-5/16” L X 3-3/16” W. (For 2 pc kit - “pre filter and panel filter”, see part# 605-850)


C C

Part# O.E.M Application Part# O.E.M Application657-134 1118-790-9930Av BufferAnti Vibration Damping For chain saw models: 028 and 038. Size: Steel plate: 1-11/16” Long X 1-3/16” Wide, with (2) 3/16” holes

657-143 1125-790-9906AV Buffer For chain saw models: 034, 036, 044, 046, 064, 066, MS340, MS360, MS440, MS460, MS640 and MS660 also fits concrete saw / cut quik saw model: TS400. Size: 34mm” Bottom OD X 28mm Top OD with 6mm ID hole in the end. Overall HT: 27mm

657-136 1121-790-99061121-790-9909

Anti Vibration Damping For chain saw models: 024, 026, 028 and 038.Size: 15/16” OD (steel washer end) X 1-5/16” OD (rubber end) with a taper to 11/16” ID in rubber end. Overall height: 1-1/16”

657-135 1121-790-99111121-790-9912

Av Buffer Anti Vibration Damping for chain sawmodels: 024, 026, 038 & 088. Size: 1” OD (steel washer end) X 1-1/8” OD (rubber end) with a 3/8” ID in rubber end. Overall height: 1-1/16”

657-009 1111-790-9905

Av BufferFor chain saw models: 015AV, 051, 076 and TS510. Use on front handle, upper damper. Size: 1-1/4” OD with a 5/16” ID hole in the steel end.

657-010 1111-790-9915Av BufferFor chain saw models: 015AV, 051, 076 and TS510. Use on front handle, lower damper. Size: 1-11/16” OD with 25/32” ID hole in the steel end.

657-140 1111-790-9900Av BufferFits chain saw models: 051, 076 and TS510. Use on back handle. Size: 1-3/8” OD with 5/16” ID hole in the steel end.

657-532 1120-790-9600

Av Buffer For chain saw models: 010, 011, 012 AV and 019T.

657-081 1123-791-2800

Av BufferFor chain saw models: MS170, MS180, MS270 and MS280. Size: 22mm (top recessed) / 25mm (bottom) X 11mm ID (recessed at the top) X 30mm overall length


657-082 1123-790-9900Anti Vibration Damping For chain saw models: 021, 023, 025, MS210, MS230 and MS250. Size: 22mm (top) / 25mm (bottom) X 11mm ID X 30mm overall length

657-083 1123-791-2805Av Buffer For chain saw models: 021, 023, 025, 029, 039, MS210, MS230, MS250, MS290 and MS390. Size: 23mm OD X 8mm ID X 30mm overall length

657-084 1128-790-9900

Av BufferAnti Vibration Damping; Tank / Annular Buffer for chain saw models: 044, 046, MS440, and 460.(Two pictures shown for reference)

657-085 4224-790-9900

Av Buffer Anti Vibration Damping / Annular buffer for Concrete / Cut off / Cut quik saw model: TS700.(Two images shown for reference)

657-086 4221-792-9300

Av Buffer Anti Vibration Damping / Rubber buffer for Concrete / Cut off / Cut quik saw models: TS460, TS700 and TS800. Measures: 1-5/8” Long X 1-3/16” Wide X 5/8” Overall HT.(Two images shown for reference)

670-101 9220-260-1100

Bar Nut Fits chain saw models: 010, 015, 020, 028 (old), 031, 032, 041, 042, 045, 056 etc.Size: 8mm X 1.25 thread. For 13mm T-wrench

670-114 0000-955-0801

Bar Nuts Bar nuts for Chain Saw models: 021, 023, 025, 026, 028 series, 038 Super series, 044, 064 etc. Size: 8mm X 1.25 thread

653-122

Bar Plate Set Bar Plates for chain saw model: 08S (newer style)



16-36



C C


1111-664-1005Bar Plate Set For chain saw models: 050, 051 and 075.

875-272 9490-000-78409490-000-7850

Drive belt (cogged)For Cut Quik models: TS350, TS360 and TS460. Size: 3/8” W X 33-3/4” L

875-273 9490-000-7851Drive belt (cogged)For concrete / cut off saw model:TS400. Size: 3/8” W X 34-7/16” L

875-3820 9490-000-7901Drive belt (multi ribbed)For concrete / cut off saw models: TS410. Size: 1/2” W X 29-1/2” L. (Type 6) MULTI RIBBED

875-3821 9490-000-7900Drive belt (multi ribbed)For concrete / cut off saw models: TS420. Size: 7/16” W X 32” L. (Type 6) MULTI RIBBED

875-3822 9490-000-78919490-000-7892

Drive belt (cogged)For concrete / cut off saw models: TS510 and TS760 with 14” blade Size: 3/8” W X 36.3” L.

623-279 1110-129-1200Intake GasketFor chain saw model: 041.

For other Carburetor parts - see our “Carburetor Kits & Parts” section

606-776 9771-021-2580Clamping Collar For our 606-414 elbow. Fit chain saw model: 038 series.

606-414 1119-141-2200Carburetor Rubber ElbowIntake Manifold - Rubber Fits 038 series chain saw.

606-412 1125-141-2200

Carburetor Rubber ElbowIntake Manifold - Rubber. Fits chain saw models: 034, 036 and MS360.

606-418 1122-141-2201

Carburetor Rubber ElbowIntake Manifold - Rubber. Fits chain saw models: 066 and MS660.

606-775 1118-182-0900

Control ShaftFits 028 series chain saws.

651-152 1118-664-16001120-664-1500

Chain AdjusterFor chain saw models: 009, 028 and 038 series (old style)

651-155 1110-664-15001110-664-1600

Chain AdjusterFor chain saw models: 030, 031,032, 041, 042, 045, 048 and 056 series.

651-157 0000-951-2911 1106-644-15001106-644-15011106-664-1501

Chain AdjusterFor chain saw models: 08S, 08 Super, 050, 051, 070, 075 & 090.

651-159 1123-640-19001123-664-1400

Chain Adjuster For chain saw models: MS210, MS230 and MS250.

651-158 1122-664-22001122-664-45001125-007-10211125-640-19009646-945-0490

Chain Adjuster KitFor chain saw models: 024, 026, 034, 035, 044, 046, 220, MS240, MS260, MS270, MS340, MS341, MS360, MS362, MS440, MS441, MS460, MS640, MS660. Includes: Tension Slide (1125-640-1900), Spur Gear, Adjusting Screw, Rubber O-ring 7X1.5 NOT shown in picture (9646-945-0490), Cover plate (1122-664-2200, Support (1122-664-4500).

646-112 1121-160-2051

Clutch Assembly For chain saw models: 026 and MS260. (Washer plate included as shown in picture). Measures: 2.675” OD X 0.403” Thick. 19mm nut attached to this clutch for removal.

16-37



C C


Clutch Assembly For chain saw models: 029 and 039. (Washer plate included as shown in picture). Measures: 2.928” OD X 0.403” Thick. 19mm nut attached to this clutch for removal.

646-116 1108-160-2002

Clutch AssemblyFor chain saw model: 08S and Cut Quik models: TS350 and TS360. Measures: 2-19/32” OD X 1/2” ID X 3/16” keyway

646-120 1119-160-2000

Clutch Assembly For chain saw model: 038 series. Measures: 2-3/4” OD X 9/16” ID - 5/8” Overall HT.

646-117 1125-165-2052

Clutch Assembly For chain saw models: 036 / MS360. Measures: 2.894” OD X 0.390” Thick. 19mm nut attached to this clutch for removal.

646-123 1125-160-2006Clutch Assembly For concrete / cut quik saw model: TS400. Measures: 2.885” OD

646-119 1122-160-2005

Clutch AssemblyFor chain saw models: 064, 066, MS640 and MS660.(Washer plate included as shown in picture). Measures: 3.140” OD X 0.460” Thick. 19mm nut attached to this clutch for removal.

646-124 1128-160-2004

Clutch AssemblyFor chain saw models: 044, 046, MS440, MS460, also fits MS341 & MS361. (Washer plate included as shown in picture). Measures: 2.916” OD X 0.392” Thick. 19mm nut attached to this clutch for removal.

621-135 0000-997-5625

Clutch SpringFor chain saw models: 015 & 024 (old style). Measures: 5-3/4” overall length.

621-138 0000-997-5425Clutch Spring For chain saw model: 028 (old).Measures: 5-7/8” overall length.

621-137 0000-997-5811Clutch Spring Fits chain saw models: 028 (new), 031, 041, 08 and 08S. Size: 15/16” overall length.

621-141 0000-997-6002Clutch SpringFor chain saw models: 051 and 075. Size: 1-1/4” length.

621-159 0000-997-0909Clutch Spring Fits chain saw models: 029,034, 036, MS 290, 340, 360, 390. Size: 7/8” overall length

621-152 000-997-0907

Clutch SpringFits chain saw models: 038, MS380. Size: 13/16” overall length

621-160 0000-997-0911

Clutch Spring Fits Stihl chain saw models:064, 066, MS640 and MS660. Size: 7/8” overall length

570-281 1121-020-12081121-020-1209

Cylinder Assy (44mm)Fits chain saw models: 026 / MS260.

570-205 1121-020-1217

Cylinder Assy (44.7 mm) Fits chain saw models: 026 / MS260. Note: With serial numbers after 2 62 187 362See our website.






026 / MS260

026 / MS260

16-38



C C


Cylinder Assy (44 mm) Fits chain saw model: 041.

570-216 1118-020-1202

Cylinder Assy (46mm) Fits chain saw model: 028 Super.

570-155 1108-020-1220

Cylinder Assy (47mm)Fits Cut Quik Saw model: TS-350. (Also fits 08 & 08S Chain Saws)

570-194 1135-020-1202

Cylinder Assy (47mm)Fits chain saw model: MS361. Bore: 47 mm, Stroke: 34 mm, Displacement: 59 cc, Rings: 47 mm X 1.2 mm.

570-190 1127-020-12141127-020-1215 1127-020-1217 1127-020-1218

Cylinder Assy (47mm)Fits Stihl chain saw models: MS310 & 029 / MS290 - read on. Give your Stihl 029 / MS290 (46 mm bore) an upgrade from 56.5 cc to 59 cc. This cylinder will also replace the older 029 (45mm bore, before SN# X 39 305 257) as well. Bore: 47 mm, Stroke: 34 mm, Displacement: 59 cc, Rings: 47 mm X 1.5 mm.

041

028 Super

TS-350 Cut Quik

MS361

MS310 029 / MS290

570-251 1125-020-12061125-020-12091125-020-12131125-020-1215

Cylinder Assy (48mm) Fits chain saw models: 034 Super, 036 & MS360. This cylinder will replace the following Stihl#’s 1125-020-1206, 1125-020-1209 & 1125-020-1213. NOTE: On older 034 saw (46mm) slight modification is required. Instructions are enclosed. This upgrade will increase your older 034 from 56.5cc to 61.5cc. (Replaces our 570-250)

570-278 4221-020-1201

Cylinder Assy (48mm) Fits Cut Quik Saw model: TS460. Note: This cylinder assemblyhas the threaded hole beside the spark plug for a decompressor. Note: Decompression valve NOT included.

570-196 1127-020-1216

Cylinder Assy (49mm)Fits Stihl chain saw models: 039 and MS390

570-227 4201-020-1200

Cylinder Assy (49mm) Fits Cut Quik Saw model: TS-360Replace your TS-350 with this C & P for extra power.

570-208 1119-020-1201

Cylinder Assy (50mm) Fits chain saw model: 038 Super.

034 Super036 & MS360

TS460

039 & MS390

TS-360

038 Super

16-39



C C


1128-020-1217

Cylinder Assy (52mm) Fits chain saw models: 046 & MS460.

570-162 1111-020-1200

Cylinder Assy (52mm)Fits chain saw models: 051 and Cut Quik model TS-510.

570-212 1122-020-1211

Cylinder Assy (54mm) Fits chain saw models: 066 & MS660.

570-200 1128-020-1121

Cylinder Assy (54mm)Fits chain saw models: 046 / MS460 (BIG BORE). Bore: 54 mm, Stroke: 36 mm, Displacement: 82.5 cc, Rings: 54 mm X 1.2 mm.

570-204 4224-020-1202

Cylinder Assy (56mm)Fits Stihl concrete / cut off saw model: TS700 and TS800.

046 & MS460

051 / TS-510

066 & MS660

046 / MS460

TS700 & TS800

570-210 1128-020-1227

Cylinder Assy (50mm) Fits chain saw models: 044(after serial# X 29 382 283) MS440.

570-209 1138-020-1201

Cylinder Assy (50mm) Fits chain saw model: MS441 and MS441C.

570-276 4238-020-1202

Cylinder Assy (50mm)Fits Cut Quik Saw models: TS410 and TS420. Decompression valve NOT included. Comes with threaded plug only.Also see our 640-285 Gasket Set.

570-272 1119-020-12021119-020-1215

Cylinder Assy (52mm) Fits chain saw model: 038 Magnum.

NOTE: This cylinder is NOT equipped with a De-compression valve hole. For a cylinder with a Decompression valve hole see our 570-206. (Also see our 623-132, 623-672, 640-238 or 640-272).

570-206 1119-020-1204

Cylinder Assy (52mm)Fits chain saw model: MS381.

Note: Decompression valve NOT included, use our 570-004 Decompression valve. Bore: 52 mm, Stroke: 36 mm, Displacement: 76.5 cc, Rings: 52 mm X 1.5 mm.

044 / MS440

MS441 / MS441C

TS410 & TS420

038 Magnum

MS381

16-40



C C


Piston Assembly (44.7mm) Fits Stihl chain saw models: 026 and MS260. NOTE: This piston assembly fits the newer 026, MS260 Stihl models after serial# 2 62 187 362. NOTE: For the older 44mm piston assembly see our 572-525.

572-384 1118-030-2001

Piston Assembly (44mm)Fits Chain Saw models: 028 and 028 Wood Boss

“older style”.

572-255 1110-030-20021110-030-2000

Piston Assembly (44mm)Fits Stihl chain saw model: 041 old style.

572-699 1113-030-2001

Piston Assembly (44mm)Fits Chain Saw model: 031.

572-388 1113-030-2003


572-449 1118-030-2003

Piston Assembly (46mm)Fits chain saw model: 028 Super. Replacement piston assembly for our 570-216.

572-605 1125-030-2002

Piston Assembly (46mm)Fits chain saw models: 034 / MS340.

572-602 1135-030-2000

Piston Assembly (47mm)Fits chain saw model: MS361. (ring thickness 1.2)

570-214 4205-020-1200

Cylinder Assy (58mm)Fits Stihl concrete / cut off saw model: TS760.

572-590 4119-030-2003

Piston Assembly (38mm)Fits Trimmer models: FS220 and FS220R.

572-601 1123-030-2001


572-604 1121-030-2005


572-607 1123-030-2003

Piston Assembly (42mm)Fits Stihl chain saw models: MS250. Note: For 025 model with larger 42.5mm bore see our 572-603 piston assembly.

572-603 1123-030-2011

Piston Assembly (42.5mm) Fits chain saw models: 025. Note: For MS250 model with smaller 42mm bore see our 572-607 piston assembly.

572-525 1121-030-2001

Piston Assembly (44mm) Fits chain saw models: 026 and MS260. NOTE: This piston assembly fits the older 026, MS260 Stihl models before serial# 2 62 187 362. They WILL NOT fit the newer MS260 models with the larger 44.67mm bore.

TS760

16-41



C C


Piston Assembly (50 mm)Fits Stihl chain saw models: 044 / MS440; with a 10mm piston pin.

572-610 1128-030-2015

Piston Assembly (50mm)Fits chain saw models: 044 / MS440. With 12mm piston pin.

572-617 4238-030-2003

Piston Assembly (50mm) Fits Cut Quik Saw model: TS410. (Replacement piston assembly for our 570-276)

572-611 1115-030-2000

Piston Assembly (50mm)Fits Stihl chain saw model: 045.

572-515 1119-030-20021119-030-2003

Piston Assembly (52mm) Fits chain saw model: 038 Magnum, MS380, MS381. (Replacement piston assembly for our 570-272.)

572-261 1111-030-2000

Piston Assembly (52mm)Fits chain saw models: 051 and Cut Quik Saw model TS-510.(Replacement piston assembly for our 570-162.)

572-612 1128-030-2009

Piston Assembly (52mm)Fits chain saw models: 044 Big Bore, 046 and MS460.

572-615 1122-030-2001


572-247 1108-030-2020

Piston Assembly (47mm)Fits chain saw models: 08, 08S, and Cut Quik model TS-350. (Replacement piston assembly for our 570-155.)

572-608 1113-030-2001

Piston Assembly (47mm)Fits Stihl chain saw models: MS310.

572-497 1125-030-2001

Piston Assembly (48mm) Fits chain saw models: 034 Super and 036.

572-614 4221-020-1201

Piston Assembly (48mm) Fits Cut Quik Saw model: TS460. Replacement piston assembly for our 570-278.

572-606 1127-030-2005


572-460 4201-030-2000

Piston Assembly (49mm) Fits Cut Quik model: TS-360. Replacement piston assembly for our 570-227

572-521 4223-030-2000

Piston Assembly (49mm) Fits Cut Quik Saw model: TS400. Replacement piston assembly for our 570-277

572-441 1119-030-2001

Piston Assembly (50mm) Fits chain saw model: 038 Super. (Replacement piston assembly for our 570-208.)

16-42



C C

Part# O.E.M Application Part# O.E.M Application574-144 1118-034-3001Piston Ring (46mm X 1.5mm)Fits chain saw models: 028 Super and 034 (with smaller 46mm bore). Replacement ring for our 572-449 piston assembly.(Priced Individually - 2 Required)

574-119 1108-034-3001

Piston Ring (47mm X 1.5mm)Fits chain saw models:08, 08S and Cut Quik model TS-350. (Priced Individually - 2 Required)

574-158 1125-034-3001

Piston Ring (48mm X 1.5mm) Fits chain saw models: 034 Super, 036 and MS360. Replacement piston ring for our 572-497.(Priced Individually - 2 Required)

574-143 1127-034-3006 4201-034-3000

Piston Ring (49mm X 1.5mm) Fits Cut Quik Saw model: TS-360 and TS400.(Priced Individually - 2 Required)

574-137 1119-034-3000

Piston Ring (50mm X 1.5mm)For chain saw model: 038 Super. (Priced Individually - 2 Required)

574-106 1115-034-30011115-034-3010

Piston Ring (52mm X 1.5mm) Fits chain saw model: 038 Magnum, 051 and TS510 cut quik saws. (Priced Individually - 2 Required)

574-248 1115-034-3010

Piston Ring Set (52mm X 1.5mm) Fits chain saw models: 038 Magnum, MS380, MS381, 045, 048, 050, 051 and 056. (Priced and sold in sets)

574-254 1115-034-3012

Piston Ring Set (54mm X 1.5mm) Fits chain saw models: 045 and 056. (Priced and sold in sets)

Note: “Piston Rings” are priced and sold individually. “Piston Ring Sets”

are priced and sold as a set of 2

572-613 1115-030-2001

Piston Assembly (52mm)Fits chain saw models: 045 and 056AV - older version.

572-390 1115-030-2002


572-616 1122-030-2005


572-620 1111-030-2002

Piston Assembly (58mm)Fits chain saw models: 075, 076 and TS760.

572-619 1106-030-20031106-030-2000


572-626 1124-030-2005

Piston Assembly (60mm)Fits chain saw models: 084 and 088.

574-212 1121-034-3005

Piston Ring Set (42mm X 1.5mm) Fits chain saw models: 024 / MS240. (Priced and sold in sets)

574-170 1110-034-30001110-034-30031121-034-3010

Piston Ring (44mm X 1.5mm)Fits chain saw models: 026 and MS260. Also fits chain saw model: 041. Replacement ring for our 572-525 piston assembly. (Priced Individually - 2 Required)

574-216 1110-034-3000

Piston Ring Set (44mm X 1.5mm) Fits chain saw models: 028, 030, 031 and 041.(Priced and sold in sets)

16-43



C C


Bearing - Piston Wrist pin bearing. For Chain Saw models: 023, 025, MS230, MS250, 024, 026, MS260 and others. (Size: 10mm X 13mm X 12.5mm).

591-101 9512-003-3140Bearing - PistonWrist pin bearing for chain saw models:08S & 038, 038 Super / Magnum and Concrete Saw models TS350 & TS360.

591-104 9512-003-3061

Bearing - Piston Wrist pin bearing for Chain Saw models: 044, 046, MS440 and MS460. (Size: 12mm X 15mm X 15mm).

591-106 9512-003-3281

Bearing - Piston Wrist pin bearing for Chain Saw models: 066 & MS660. (Size: 12mm X 17mm X 13mm).

591-110 9512-003-3440

Bearing - Piston Wrist pin bearing for Chain Saw models: 051 & 075

590-150 1119-030-0400

Crankshaft Assembly For chain saw models: 038, 038 Super and 038 Magnum.

590-117 1110-030-0401

Crankshaft Assembly. For Stihl chain saw model: 041.

590-119 1111-030-0402

Crankshaft Assembly For chain saw models: 051, 075 and Cut Quik Saw model TS-510.

590-116 1108-030-0402

Crankshaft Assembly For Cut Quik Saw models: TS-350 and TS-360, also fits Chain Saw models: 08 and 08S.

590-156 4223-030-0400

Crankshaft Assembly For Cut Quik Saw model: TS400.



590-120 1106-030-0400

Crankshaft Assembly For chain saw models: 070 and 090.

592-109 9503-003-0540Bearing - Crankshaft Fits chain saw models: 051 and 075 - (clutch side) Size: 20mm ID X 47mm OD X 14mm HT. (Bearing# 6204/C3) Open both sides

593-102 9503-003-0310Bearing - CrankshaftFits chain saw model: 041 - (flywheel side)Size: 15mm ID X 32mm OD X 9mm HT.(Bearing# 6002/C3) Open both sides

593-103 9503-003-04409503-003-0450

Bearing - CrankshaftFits Stihl chain saw models: (flywheel side) 038, 038 Super, 038 Magnum, 051, 075 and TS-510 and TS-400 (recoil side) cut quik saws. Also Stihl TS480i, TS500i, TS700 and TS800 Cutquik saws.Size: 17mm ID X 40mm OD X 12mm HT.(Bearing# 6203/C3) Open both sides

592-106 9503-003-03409503-003-0341

Bearing - Crankshaft Fits models: 08S, 038,038 Super, 038 Magnum and 041 - (clutch side). Cut-Quik models: TS350 & TS360 - (clutch & flywheel side); also fits Cut-Quik model: TS400. Fits models 034, 036, 044, 046, MS360, MS440 and MS460 (flywheel side). Size: 15mm (37/64”) ID X 35mm (1-3/8”) OD X 11mm (7/16”) HT (Bearing# 6202 - open both sides)

570-002 4223-020-94004238-020-9400Wacker# 0104064

Decompression Valve For Chain Saw and Concrete saw cylinder assemblies. Fits models: TS400, TS700 and TS800

570-004 1128-020-9400

Decompression ValveFor Chain Saw and Concrete saw cylinder assemblies. Fits models: 026, 036, 044, 046, 066, MS260, MS360, MS440, MS441, MS460, MS650, MS660.

640-269

Gasket Set Fits chain saw model: 028 Super. (No oil seals included)



16-44



C C


Gasket SetFits chain saw models: 034, 034 Super, 036 (No oil seals included)

640-268

Gasket SetFits chain saw models:034, 036, MS340 and MS360.(Oil seals included (1) 622-241 (15mm ID X 29.6mm OD X 4mm) + (1) 622-226 (12mm ID X 20mm OD X 5mm).

640-272

Gasket Set Fits chain saw model: 038 series. (Includes oil seals)

640-136Gasket Set Fits chain saw models: 050 and 051. (No oil seals included)(While Quantities Last)

640-287

Gasket Set Fits chain saw models: 08, 08S and Cut Quik models: TS-350 and TS-360. (Includes oil seals)

640-181 4223-007-1050

Gasket Set Fits Cut Quik model: TS400. (oil seals included)

640-285 4238-007-1003

Gasket Set Fits cut quik / concrete saw models: TS410 and TS420. (Includes oil seals)For use with our 570-276 Cylinder Assembly.

640-275

Gasket Set Fits chain saw models: 044 and MS440. (Includes oil seals)


640-279

Gasket Set Fits chain saw models: 046 and MS460. (Includes oil seals)

640-280Gasket SetFits chain saw models: 066 / MS660. (Includes oil seals)

640-281

Gasket SetFits Stihl concrete saw / cut quik saw model: TS460.

640-282

Gasket SetFits Stihl concrete saw / cut quik saw model: TS760. (Oil seals included)

623-611 1118-029-2305Head / Base GasketFits chain saw models:026, 028, 031 and 032.

623-672 1119-029-2300

Head / Base Gasket Fits chain saw models: 038, 038 Super & 038 Magnum.(Fits our 570-208 and 570-272).

623-678 1110-029-2300

Head / Base Gasket Fits chain saw model: 041.

623-687 1108-029-2300

Head / Base Gasket Fits chain saw models: 08, 08S &Cut Quik models: TS-350 and TS-360.

623-431 1111-029-2300

Head / Base Gasket Fits chain saw models: 051 and Concrete saw model: TS510.

623-612

Head / Base Gasket onlyFits Stihl chain saw models: 044 / MS440. (Metal).

16-45



C C



623-614


623-615

Head / Base Gasket onlyFits Stihl concrete / cut quik saw model: TS400. (Metal).

610-170 1115-350-35030000-350-3500

Fuel Filter For chain saw models using 1/4” molded fuel lines. Models: 038, 044, 044, 046, MS460, 064, 066 etc. (Orange colour).

610-055 1110-358-1800Replacement Fuel Filter Element For our 610-170. Will replaces the original Stihl element. Measures: 1” L X 3/4” OD (Made of foam material).

613-605 0000-350-35001115-350-3503

Fuel Filter - In Tank Use with molded fuel lines. Fits chain saw models: 034, 036, 038 etc with molded fuel lines. Measures: 11/16” OD X 1-5/8” overall length.

613-607 0000-350-35041115-350-3503

Fuel Filter - In TankFor use with molded fuel lines. Fits chain saw models: 034, 036, 038, 044, MS440, 046, MS460, 064, MS640, 066, MS660 etc with molded fuel lines. NOTE: Similar to our our 613-605 but larger diameter. Recommended for larger cc Stihl chain saws. etc. Measures: 1-3/4” overall length X 23mm diameter.

610-125 1123-358-77011123-358-7702

Molded Fuel Line Fits chain saw models: 021, 023, 025, MS210, MS230, MS250.Note: Designed to be used with engines manufactured before January 2012; Not to be used with engines manufactured after January 2012.

610-122 1127-358-7702

Molded Fuel LineFits chain saw models: 029, 034, 036, 039, MS290, MS360, MS390.

610-121 1119-358-77001118-358-7701

Molded Fuel Line For chain saw models: 034, 034 Super and 036 (previous to serial number) X39108850; 038 series as well as model 064 (previous to serial number X19512349.) Measures: 4-3/4” Long

610-128 1119-358-7702

Molded Fuel LineFits chain saw models: MS381

610-129 1128-358-7701

Molded Fuel Line Fits chain saw models: MS341, MS361, 044, 046, MS440 & MS460.

610-130 1124-358-7700

Molded Fuel Line For Stihl. Fits chain saw models: 066, MS650 and MS660.

610-132 1106-647-9404

Molded Oiler Hose / Oil TubeFits the following chain saw models: 028, 030, 031, 032, 038, 070, 075, 090, MS 380, MS 381. This hose connects to the oil pump.

610-134 1122-647-9400

Molded Oiler Hose / Oil Tube ONLY, Pick-up filter body not included. Oil pump pick-up hose only. Fits the following Stihl chain saw models: 024, 026, 034, 034, 036, 036QS, 064, 066, MS240, MS260, MS260C, MS340, MS341, MS360, MS360C, MS361, MS361C, MS362, MS362C, MS441, MS441C, MS640, MS650 and MS660.

550-120 1110-350-0502Fuel Cap For chain saw models: 041, 051 and 075.

550-145 0000-350-05201117-350-0500

Fuel & Oil Cap (40mm) Gas Cap for chain saw models: 020, 021, 023, 024, 025, 026,028, 028 Super, 029, 034, 034 Super, 036, 038 series, 039, 044, 046, MS290, MS310 and MS390. Oil Cap for Stihl chain saw models: 044, 046, 050, 064, 084, MS640, MS650 and MS660.

550-158 0000-350-0531 1124-350-0500

Fuel Cap For chain saw models: 064, 066, MS660 and 084. Thread OD: 1.54” or 39.06mm

16-46



C C

Part# O.E.M Application Part# O.E.M Application550-121 1107-350-0500Fuel Cap For chain saw models: 08, 08S, 070, 090 and Cut Quik models: TS-350 and TS-360.

551-149 0000-350-05101117-640-3600

Oil Cap and Fuel Cap (30mm) For chain saw models: 009, 010, 011, 012, 020, 021, 023, 024, 025, 026, 028, 028 Super, 032, 034, 034 Super, 036, 038, 042 and 048. Fuel Cap for chain saw model: 048.

551-155 0000-350-0526Oil Cap For chain saw models: HT 100, HT 101, HT 130, HT 131, HT 250, HT 70, HT 73, HT 75, HTE 60, HT-KM.Gas CAP For the following models: 021, 023, 025, 026, 034, 036, 036QS, MC 200, MS 171, MS 181/C, MS 192/C/T, MS 200/T, MS 210/C, MS 211, MS 230/C, MS 240, MS 250/C, MS 260/C, MS 340, MS 360/C and MS 381.(Flip Top Style). Size: O-Ring Seal OD = 1.20”. NOTE 1: Two pictures shown for reference.NOTE 2: NOT compatible with > 10% ethanol fuel.

550-160 0000-350-0525Fuel CapFor chain saw models: 020, 021 023, 024, 025, 026, 029, 034, 036, 039, 044, 046, 088, BG45, BG46, BG55, MS171, MS181, MS192, MS200, MS210, MS211, MS230, MS240, MS250, MS260, MS270, MS290, MS310, MS340, MS341, MS360, MS361, MS362, MS380, MS381, MS440, MS441, MS460 and MS880. (Flip Top Style). Size: O-Ring Seal OD = 1.35”. Note: NOT compatible with > 10% ethanol fuel.

550-164 4223-350-0500

Fuel Cap / Gas Cap For Stihl concrete / cut quik saw model: TS400. Note: NOT compatible with > 10% ethanol fuel.

627-038 1119-640-71001119-642-1501

Oil Pump Spur Gear & Oiler Worm Gear Set for Stihl. Includes (1) oil pump spur gear (Replaces Stihl# 1119-642-1501). This nylon gear drives the oiler gear on saw & fits Stihl chainsaw models: 038, MS380 & MS381 ONLY. Also included is (1) oiler worm gear (Replaces Stihl# 1119-640-7100). This nylon sprocket comes complete with bushing attached. It drives the oiler and fits on Stihl chainsaw models: 038, MS380, MS381 as well as 028, 042 and 048 models.

627-380 1119-640-3200

Oiler / Oil Pump AssemblyFits chain saw models: 038, MS380, MS381, 042AV and 048.

627-326 1121-007-10431121-640-3203

Oiler / Oil Pump Assembly Fits chain saw models: 024, 026, MS240 and MS260.

627-336 1125-640-3201

Oiler / Oil Pump AssemblyFits chain saw models: 034, 036 and MS360.

627-346 1128-640-3206

Oiler / Oil Pump Assembly Fits chain saw models: 046, MS460, MS441 & MS441C.

627-660 1122-640-3205

Oiler / Oil Pump Assembly Fits chain saw models: 066 / MS660.

627-026 1121-640-7111

Worm GearFits chain saw models: 026, MS260 and (Later Type) MS240 and MS261.

627-029 1125-640-71101125-647-2400

Worn Gear and Spring Fits chain saw models: 029, 034, 036, 039.

600-169 0000-400-1306

Electronic Coil Fits chain saw models: 009, 010, 011, 012, 020, 020T, 021, 023, 025, MC 200, MS200, MS210, MS230 and MS250.

16-47



C C


1110-430-02101121-430-0200

Stop Switch Kill Switch for chain saw models: 024, 026, 070 and Cut Quik Saw models 08S, TS-350 and TS-360. Measures: 3/4” X 1” X 1-1/2”

430-017 Universal Type

Toggle Kill Switch Kill switch found on many small older Chain Saw models with spade terminal wire end.

636-150 1121-140-0606

Muffler / Exhaust For chain saw models: 024, 026 and MS260.

636-152 1127-140-0605

Muffler / Exhaust For chain saw models: 029, 039, MS290, MS310 and MS390.

636-151 1125-140-0607Muffler / Exhaust For chain saw models: 036, MS360 and will fit some 034 Super models - see measurements. Mounting bolt holes measure: 1.69” / (43mm) center to center / bolt holes measure: 7.3mm OD. Muffler measures: 3” deep approximately.

636-138 1119-140-0604

Muffler For chain saw models: MS381. (Uses our 623-132 exhaust gasket). For older 038 series see our 636-139 muffler.

636-139 1119-007-10051119-140-06001119-007-1027

Muffler / Exhaust For chain saw models: 038 and 038 Super. Note: Front and back images shown for reference. (Uses our 623-132 exhaust gasket)

623-132 1117-149-0601 1115-149-0601

Chainsaw Exhaust Gasket For chain saw models: 038 series.

600-402 1123-400-1301

Electronic Coil Fits chain saw model: MS250.

600-358 0000-400-1300

Electronic Ignition For chain saw models: 024, 026, 028, 028WB, 029, 034,034AV, 036, 038, 039, 044, 048, 064, MS240, MS260, MS290, MS310, MS340,MS360, MS380, MS381, MS390, MS440 and MS640; also Trimmer models: FS360 and FS420.

600-406 1122-400-1314

Electronic Ignition. Fits on Stihl chain saw models: 046, 066, MS460, MS650 and MS660

600-400 4223-400-1303

Ignition Coil For concrete / cut quik saw. Fits model: TS400. Two bolt style (bolts not included). Coil comes complete with 13” of 5mm coil wire.

600-100Ignition Coil and Core For chain saw models: 08 and 08S. NOTE: Found on other equipment using the old 08 style power plant. ie: Stihl auger etc.

600-901

Ignition Coil and Core For chain saw models: 041 and 045.

600-401 1111-400-13051113-400-1305

Ignition Coil For chain saw models: 051 NOTE 1: We are not certain which OEM# (original equipment manufacturer number) is correct. Please see picture for reference. (While Quantities Last)

16-48



C C


Muffler / Exhaust Muffler for chain saw models: 040, 041 and 041G. (Uses our 623-157 exhaust gasket)

636-154 1128-140-0616

Muffler / Exhaust Dual port muffler for chain saw models: 044, 046, MS440 & MS460. This is an aftermarket muffler. The dual port design add power. Complete with front baffle and spark arrester screens.

636-156 1122-140-0614

Muffler / Exhaust Single Port muffler for chain saw models: 066, MS660 & MS650.

636-153 1122-140-06131122-140-0800

Muffler / ExhaustDual Port muffler for chain saw models: 066, MS660 and MS650. (Also see our 636-156)

636-117 1108-140-0600

Muffler / Exhaust For models:08 and 08S. Note: Front and back images shown for reference.

636-171 4201-140-06074201-149-0601

Muffler / Exhaust For Cut Quik Saw models: TS350 and older TS360. NOTE: photo shows front and back images.

622-226 9640-003-1190

Oil seal For models: 020, 024, 026, 034, 036, MS360, FS220, & 280 Size: 12mm X 20mm OD X 5mm.

622-233 9640-003-13409640-006-1314

Oil seal For chain saw models: 028, 030, 031, 032, 038, MS380, MS381 (Magneto side). Trimmer models: FS360, FS420, FS500 and FS550 and Blower models: BR 320, BR 340 L, BR 380, BR 400, BR420, BR420 C, SR 320, SR 400, SR 340 and SR 420. Size: 13mm X 22mm OD X 5mm


622-241 9640-003-1600

Oil Seal (Clutch Side). Fits chain saw models: 026, 028 Super, 034, 036, 044, MS440, 046 and MS460. Trimmer models: FS360, FS420, FS500 and FS550. Size: 15mm X 29.6mm OD X 4mm HT. NOTE: You can find (1) 622-241 oil seal in our 640-268 gasket set.

622-266 9640-003-1880Oil Seal (PTO side) Fits chain saw models: 038 and 038 Super. Size: 17mm X 39.5mm OD X 5mm

622-249 9640-003-1610Oil Seal (PTO & Mag side)Fits chain saw models: 08 / 08S & Cut Quik models: TS350and TS360.

615-514 0000-350-6202 1130-350-6200

Primer Bulb AssemblyFits Zama carburetors. Found on Stihl concrete / cut off saw models: TS400, TS800; Mounting hole: .576” (Uses our 615-028 replacement primer bulb). Note: This primer assembly has a coil spring inside the primer bulb.

135-110 1128-405-1000Spark Plug Boot with SpringFor chain saw models: 009, 010, 011, 012, 017, 018, 020, 021, 023, 024, 025, 026, 029, 034, 036, 039, 044, 046, 056, 064, 066, 084, 088, MS170, MS180, MS192T, MS210, MS230, MS240, MS250, MS270, MS290, MS310, MS340, MS341, MS360, MS361, MS380, MS390, MS440, MS441, MS460, MS640, MS650, MS660 and MS880.

135-061 UniversalSpark Plug Wire (5mm OD)Plug Wire for chain saw models: 08, 08S and Cut Quik Saw models:TS-350 and TS-360. Quality black hypolon outer case with COPPER (not carbon) inner wire. 5mm Spark (Priced and Sold in 10 meter / 33 FT rolls)

650-141 1118-648-04001119-648-0400

Sprocket Side CoverFor chain saw models: 024 and 028 (new).

650-154 1125-640-17011125-648-0402

Sprocket Side Cover Fits chain saw models: 024, 026, 028 Super, 029, 034, 036, 038, 038 Magnum. (Made of Plastic)


16-49



C C


Sprocket Side CoverFor chain saw models: 08 and 08S. Complete with tank cover.

681-134Sprocket Needle BearingFits many chain saw manufacturers drive sprockets. Fits chain saw models: 009, 010, 011, 012, 021, 023, 024, 025, 026, 34 and 36 (PRIOR TO x25809074). (Size: 10mm X 13mm X 10mm) NOTE: This bearing will not replace the plastic needle bearing type used on newer models.

681-125 0000-993-3008Sprocket Needle Bearing For chain saw models: 08S and Cut-Quik models: TS350 and TS360. (Size: 15mm X 18mm X 17mm) NOTE: This bearing will not replace the plastic needle bearing type used on newer models.

681-128Sprocket Needle Bearing Fits models: 028 series.(Size: 10mm X 13mm X 23mm)

681-127Sprocket Needle Bearing Fits chain saw models: 038. 042, 048 (Spur Only)(Size: 12mm X 16mm X 24mm)

681-126 9512-933-2382

Sprocket Needle Bearing Fits our chain saw sprockets fitting on models: 044, 046, MS440, MS460, 064, 066, MS640 and MS660. NOTE: Will also replace the original STIHL (plastic cased needle bearing) in the MS390. (Size: 10mm X 16mm X 12mm)

681-129Sprocket Needle BearingFits our chain saw sprockets fitting on models: 084, 088. (Size: 12mm X 17mm X 13mm)

671-110

Sprocket Nut Fits chain saw models: 08, 08S; also found on older Cut Quik model: TS350

672-110Flywheel Nut Fits chainn saw models: 08, 042, 045, 056, 070, 090; also found on Cut Quik models: TS350 & TS360


655-029 1127-080-2103 / A

Starter Assembly For chain saw models: 029, 031, 039, MS290, MS310, MS390.This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawls, handle etc. Just needs to be bolted on. (Housing is made of plastic).

655-034 1125-080-2105

Starter AssemblyFor chain saw models: 034, 034 AV, 034 Super, 036, MS340 and MS360.This aftermarket assembly comes complete with housing,starter pulley, spring, rope, pawls, handle etc. Just needs to be bolted on. (Made of metal).

655-038 1119-080-1800

Starter Assembly For chain saw models: 038 series. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawls, handle etc. Just needs to be bolted on. (Made of cast metal).

655-044 1128-080-2104

Starter Assembly For chain saw models: 044, 046, MS440 and MS460. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawls, handle etc. Just needs to be bolted on. (Made of cast metal).

655-066 1122-080-2110

Starter Assembly For chain saw models: 066, MS650 and MS660. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawls, handle etc. Just needs to be bolted on. (Made of cast metal).

16-50



C C

Part# O.E.M Application Part# O.E.M Application655-035 1108-080-2101 / 1108-080-2115

Starter Assembly For chain saw model: 08 & 08S and Concrete / Cut Quik saw model: TS350. This aftermarket assembly comes complete with plastic housing, metal starter pulley, spring, rope, pawl, elasto starter handle etc. Just needs to be bolted on. (This assembly is the newer - 1 nylon starter pawl set up).

655-040 4223-190-0401

Starter Assembly For concrete saw / cut quik saw model: TS400. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawl, handle etc. Just needs to be bolted on. (Made of Nylon)

655-042 4238-190-0300 / 4238-190-0301 4238-190-0302 / 4238-190-0402B

Starter AssemblyFor concrete saw / cut quik saw models: TS410 and TS420. This aftermarket assembly comes complete with housing, starter pulley, spring, rope, pawl, handle etc. Just needs to be bolted on. (Made of Nylon)

560-119

Starter Handle For chain saw models: 010,011, 015, 021, 028, 031 and 032.

560-213 1121-195-3400

Starter Handle For chain saw models: 021, 023, 024, 026, 028, 028 Super, 034, 034 Super, 036, 044, 046, 064, 066 (New style), concrete saw models: TS350, TS360, TS510 and TS360

560-118 1110-195-3400

Starter HandleFor chain saw models: 08, 038, 041, 042, 050, 051, 056, 070, 075 and 090. (Old style)




560-120 1113-195-82000000-190-3400

Elasto Starter Handle and RopeFor many Stihl saws. Medium starter handle with rubber buffer to help obsorb the kick that you get from some of the larger Stihl saws. Rope diameter is 4mm X 36 inches long.

560-121 1122-190-3400

Elasto Starter Handle and Rope For many Stihl saws.Large starter handle with rubber buffer to help obsorb the kick that you get from some of the larger Stihl saws. Rope diameter is 4.5mm X 38 inches long.

560-111 1118-195-7200Starter Pawl (nylon)For Stihl chain saw models: 009, 010, 011, 012, 024, 028 (old style) and 032.

560-170 1117-195-7200Starter Pawl (nylon)For Stihl chain saw models: 08, 038, 042, 048, 051, 056 and 070 (old style). Size: 1.11” overall length X

.375” overall height not including positioning nub.

560-202 1124-195-04011124-195-7200

Starter Pawl (nylon)For Stihl chain saw models: 038, 041, 042, 045, 048, 050, 051, 056, 064, 066, 070, 076, 08S, 084, 088, MS380, MS640, MS650, MS660, MS880; also fits Cut Quik Saw models TS350 and TS360.Size: 1.12” overall length X .475” overall height not including positioning nub. (newer style)

560-203 1125-195-72004116-195-7200

Starter Pawl (nylon)For chain saw models: 009, 010, 011, 012, 017, 018, 019T, 020, 020T, 021, 023, 024, 025, 026, 028, 029, 034, 036, 039, 044, 046, MS170, MS180, MS190T, MS191T, MS192T, MS200, MS200T, MS210, MS230, MS2400, MS250, MS260, MS270, MS290, MS310, MS3400, MS341, MS360, MS 361, MS440 and MS460.

560-784 0000-195-72004116-195-7200

Starter Pawl (metal pin)Fits concrete saw model: TS400; as well as models: BR320, BR320L, BR340, BR340L, BR380, BR400, BR420, BR500, BR550, BR600 back pack blowers; FR220, FS106, FS160, FS180, FS220, FS280.

16-51



C C


Spring Clip / Pawl Spring Fits chain saw models: 009, 010, 011, 012, 024,026, 028, 032 old style. (For use with our 560-111 starter pawls).

630-111 1128-195-3500

Spring Clip / Pawl Spring Fits chain saw models: 024, 026, 028, 034, 036, MS360, 039, MS390, 044, MS440, 046, MS460 etc. (For use with our 560-203 starter pawls).

630-118 1124-195-3500

Spring Clip / Pawl Spring Fits chain saw models: 064, 066, MS640, MS660 and 084. Size: 1-3/4” overall length X 1-1/8” approximately(For use with our 560-202 starter pawls).

630-179 1117-195-3500

Spring Clip / Pawl SpringFits chain saw models: 038, 041, 042, 045, 048, 050, 051, 056, 070, 076, 08S, MS380 & MS381.

560-189 1123-195-0400

Starter Pulley (nylon)Fits chain saw models: 017, 018, 019, 020, 021, 023, 025, MS170 / 180 / 190 / 191 / 192 / 200 MS210, MS230 and MS250. Measures: 2-1/2” OD (2) pawl pulley

560-190 1118-190-1000

Starter Pulley (nylon)For chain saw models: 028 and 024 (old style). Measures: 2-9/16” OD (1) pawl pulley

560-201 1125-195-04001125-195-0401

Starter Pulley (nylon)For chain saw models: 024, 028 (new-style) and 034. Measures: 2-3/4” OD (2) pawl pulley

560-237 1128-195-0400

Starter Pulley (nylon) For chain saw models: 029, 034, 036, 039, 044, 046, MS261, MS271, MS290, MS291, MS310, MS311, MS340, MS341, MS360, MS361, MS362, MS390, MS391, MS440, MS441 and MS460.Measures: 2-11/16” OD (2) pawl pulley




560-224 1117-007-10141117-195-0402

Starter Pulley (metal)For chain saw models: 038, 041, 042, 045, 048, 051, 056, 08, 070, 075, 076, and Cut Quik models: TS350, TS360, TS510 & S760. Measures: 3-1/8” OD (2) pawl pulley(Uses our 560-202 & 630-179)

560-146 1107-190-1000

Starter Pulley (metal)For chain saw models: 08, 08S and 070. Measures: 3” OD (2) pawl pulley

560-200 1122-195-0400

Starter Pulley (nylon)For chain saw models: 08S, 051, 064, 066, MS640, MS650 and MS660. Measures: 2-27/32” OD (2) pawl pulley

560-225 4238-190-1001

Starter Pulley With brass bushing. For Cut Quik / Cut off saw models: TS410, TS420, TS480i and TS500i. Measures: 3” (76.82mm) Bottom OD X 2.74” (69.63mm) Top OD X .412 (10.47mm) ID / Bore. (1) pawl pulley. Uses our 560-784 Starter Pawl.(Two Images shown for reference)

560-101 1106-190-4600

Starter Dog Assembly (Large)Found on many older chain saws using an aluminum starter cup. Size: Dog width: 1/2” with a 3/8” ID.

560-116 0000-961-5116

Starter Ring (nylon)For chain saw models: 08S, 041, 045 and 070. Size: 2-1/4” OD

625-500 1111-195-1600

Starter SpringFor chain saw models: FS08, FS410, 410AV, 410 AVE (...5816400)

16-52

STIHL continuedSTIHL continued


C C



625-502 1116-195-1600

Starter SpringFor chain saw models: 009, 010, 011 (...X12725130) and 015.

625-503 1118-190-0600

Starter SpringFor chain saw models: 024, 026, 028, 032 and 034.

625-504 1114-190-0600

Starter SpringFor chain saw model: FS150, 151, 200AV and 200AVSE.

625-506 1115-190-0600

Starter SpringFor chain saw model: 045. (...#5919431)

625-507 1160-190-0600Starter SpringFor chain saw models: 08, 070, 090, 510 and Cut Quik Saw model: TS350 (old model - wide spring).

625-508 1117-190-0600


625-509 1117-190-0601Starter SpringFor chain saw models: 038, MS380, 041 (#5816401...), 042 (after serial# 5676790), 045 (before serial# 5919431...), 048, 050, 051 (after serial# 674961...), 056, 070, 075, 076 and Cut Quik models: TS-350, TS-360, TS510 and TS760 (new model - narrow spring).

625-510 1110-190-0600

Starter SpringFor chain saw models: 040 and 041 (...#2663618).

625-511 1120-195-1600

Starter SpringFor chain saw models: 009, 010, 011 (X12725130...) and 012.

625-516 1128-190-0600

Starter SpringFor chain saw models: 036, 044 and 046.

625-517 1122-190-0600


625-522 1122-190-0605

Starter Spring For chain saw models: 066, MS650 and MS660. Comes complete with nylon case.

625-518 1124-190-0600


625-519 1129-190-0600

Starter SpringFor chain saw models: 017, 021, 023, 025, 029 and 039.

625-520 4223-190-0600

Starter SpringFor Cut Quik Saw / Concrete Saw model: TS400. Measures: 2.348” diameter

625-521 1129-190-0601

Starter SpringFor chain saw models: 034, 044 and 046.

625-526 4282-190-06004282-195-0300

Starter SpringFor Cut Quik Saw / Concrete Saw model: TS410 and TS420. Measures: 2.479” diameter

16-53

STIHL continuedSTIHL continued


C C


9490-000-7850

Drive Belt (Cogged Belt)For concrete / cut off saw models: TS350, TS360 and TS460. Size: 3/8” W X 33-3/4” L

875-273 9490-000-7851

Drive Belt (Cogged Belt)For concrete / cut off saw model: TS400. Size: 3/8” W X 34-7/16” L

875-3822 9490-000-78919490-000-7892

Drive Belt (Cogged Belt)For concrete / cut off saw model: TS510 & TS760, with 14” blade Size: 3/8” W X 36.3” L(Kevlar - Cogged Raw Edge V-Belt).

875-3821 9490-000-7900

Drive Belt (Multi Ribbed)For concrete / cut off saw models: TS420. Size: 7/16” W X 32” L.

875-3820 9490-000-7901

Drive Belt (Multi Ribbed)For concrete / cut off saw models: TS410. Size: 1/2” W X 29-1/2” L.

654-143 1121-790-1701

Tube Handle For chain saw model: 024.

654-139 1118-790-1700

Tube Handle For chain saw models: 028 and 028 Super.

654-137 1119-790-1700

Tube HandleFor chain saw models: 038 and 038 Super.




654-128 1110-790-1510

Tube HandleFor chain saw model: 041 (old style).

654-133 1110-790-1716

Tube Handle For chain saw model: 041 (new style).

654-126 1108-790-1500

Tube Handle For chain saw model: 08S and Cut Quik models: TS350 & TS360.

654-145 1122-790-1700

Tube Handle For chain saw models: 064 and 066.

654-125

Wrap HandleFor chain saw models: MS230 and MS250.

654-129

Wrap HandleFor chain saw models: MS290 and MS390.

654-140 1128-790-17501128-790-1753

Wrap HandleFor chain saw models: 044, 046, MS440 and MS460.





16-54



C C


T Wrench / ScrenchFits models: 009, 010, 011, 015, 020, 021, 023, 024, 025, 026, 028, 031, 032, 034, 036, 038, 041, 048 and 056.Bar nut= 1/2” or 13mm. Spark plug = 3/4” or 19mmA = 6-3/4”, B = 1-1/16”, C = 1

705-590

T Wrench / ScrenchFits chain saw models: 044, MS440, 046, MS460, 064, MS640. Bar nut= 1/2” or 13mm. Spark plug = 3/4” or 19mmA = 7”, B = 1-5/8”, C = 1”

705-635 Carlton# 41C1719

T Wrench / Scrench.Bar nut= 11/16” or 17mm. Spark plug = 3/4” or 19mmA = 6-3/4”, B = 1-5/16”, C = 1-5/16”

705-525

T Wrench / Scrench Fits chain saw models: 08S, 051, 051, 075, 090 and Cut Quik models: TS350 & TS360.Bar nut= 11/16” or 17mm. Spark plug = 13/16” or 21mmA = 7”, B = 1-11/16”, C = 1-5/8”

705-202 5910-890-2400

Torx WrenchFor bolts found on Stihl equipment. Special 6 - sided torx head. NOTE: Picture shows a close up of torx end for reference

A

B

C

A

B

C

A

B

C

A

B

C

705-592 Carlton# 41C1319TOregon# 57-019

T Wrench / ScrenchUsed on Husqvarna and Stihl cut quik / cut off / concrete saws. Fits Stihl concrete / cutquik saw models: TS350, TS350AVE, TS360, TS400, TS460, TS700 and TS800.Size: 1/2” (13mm) Bar Nut X 3/4” (19mm) Spark Plug X (B = 2”) + (C = 1”) = 3” total with a 7-3/4” long handle. T27 Torx End.

705-634

T Wrench / ScrenchFits most new Stihl chain saws.Size: 11/16” (17mm) Bar Nut X 3/4” (19mm) Spark Plug X (B = 1-7/16”) + (C = 1-1/2”) = 2-15/16” total with a 7-3/4” long handle. T27 Torx End.

TANAKA625-850 779 00601 203

Starter Spring For chain saw models: ECS-350 and 355.

625-854 777 11600 911

Starter SpringFor chain saw models: ECS-506 and 650.

625-858 778 00601 900778 01800 900

Starter Spring For chain saw models: ECS-351, 356, 405 and 415.

625-859 778 11600 910

Starter SpringFor chain saw models: ECS-505.

16-55


Documents

Section16 Part1 A-H - Banta · PDF fileand trimmer models with spade terminal wire end. 135-053 Spark Plug Boot For many Chain Saws & Trimmers. ... Size: 1/8” ID X 3/16” OD (50