14

SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver

  • Upload
    others

  • View
    2

  • Download
    0

Embed Size (px)

Citation preview

Page 1: SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver
Page 2: SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver

SECURITY SYSTEMS

General DescriptionISO 9001: 2008

EN ISO 14001: 2004

Optima high security hydraulic arm barriers are designed especially for entrance points which have medium level of threat of vehicle attack or for the ones that have medium level security requirements. Optima high security hydraulic arm barriers are designed to K4 standards.

CABINETBarrier cabinet is designed to IP 55. Body front lid and top lid is manufactured from A1 Quality Steel. They are phosphate plated, RAL 2004 electrostatically powder coated and then furnaced. Anchoring to the floor is achieved by a galvanized anchoring plate. There are air circulation openings on the front lid which is opened by a key. ARMThe beam of the barricade is 100 mm diameter steel tubing or 100x100 mm box beam with locking structure welded on both sides. Arm supports are fabricated from box beams. Maximum arm length can be as long as 10 meters.

HYDRAULIC POWER UNIT AND CONTROL ELECTRONICSAll the hydraulic components are tested at 250 bars although normal operating pressure is around 75-100 bars. Manuel hand pump is standard in HAB series, therefore in case of power failure it is possible to raise and lower the barrier by manual hand pump. Hydraulic cylinder has cushions at both ends. Cooler fan or heater can be integrated inside the cabinet optionally. Optima barriers are controlled with the help of advanced microelectronics. Unit comes with a desktop control keyboard. Motor is driven by a contactor and protected by a thermic breaker. The low current voltage required by the system is supplied by a switch mode power supply. There is a fuse for every component in the system.Traffic light can be integrated to prevent accidents, the traffic lights have independent lights for arm lowered (red color) and arm raised (green color). The lights change state automatically depending on barrier position. In addition to this, radio control receiver, transmitter and antenna, safety photocell, loop detectors, flashing lights, card reader etc. can be integrated to the system easily. Barrier control system can be controlled remotely and connected to an external computer system via a communication link (ethernet). All the cables running in the system are color coded and numbered for easy tracking. It possible to check the position of barrier by using SCADA system or any control system.

Hydraulic Arm Barriers

www.optima-engineering.com

Gate Barriers

HYDRAULIC ARM BARRIERS

Page 3: SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver

OPTIONAL ACCESSORIES 1. Red/green traffic lights. 2. Flashing light 3. Safety photocell, stand and casing4. Inductive loop detector5. Card reader system6. Uniterrupted power supply (UPS)7. Transformer to convert to power. 8. STOP sign in middle of barrier arm. 9. Heater or cooler fan.

www.optima-engineering.com

SIDE VIEW TOP VIEW

1120

mm

Up to 10000 mm

435 mm

435 mm

520

mm

ENVIRONMENTAL CONDITIONS AND POWER REQUIREMENT Between 20°C and +75°C, %95 non condensing humidity, 380-415 VAC, 50-60 Hz (or 220-240 VAC, 50-60 Hz optional)

Page 4: SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver

SECURITY SYSTEMS

General DescriptionISO 9001: 2008

EN ISO 14001: 2004

OPTIMA HDAB-CT Series Crash Tested Hydraulic Drop Arm Barriers are designed especially for entrances where there is a threat of suicide vehicle attack, or for the entrances that have very high security requirements. If there is a threat of vehicle attack in addition to the control of vehicle access in high security applications, hydraulic drop arm barriers are one of the best and most secure solutions. Even though the attack is from high tonnage vehicles with high speeds, it is not possible for the vehicle to keep on moving forward anymore beyond the arm of the barrier. Optima Hydraulic Crash Tested Drop Arm Barriers are designed for PAS68:2013 crash rating and classified as PAS 68:2013 Rising Gate V/7500[N3]/80/90:0.0/2.1. (This means that M50-P1 "zero penetration" according to American standard). Drive unit is electro-hydraulic, but in case of power failure drop arm barrier can be lowered or lifted manually with the help of hand pump. Thanks to advanced control electronics, raise/lower function can be achieved by every kind of card readers, biometric readers like fingerprint or hand shape, radio control, on/off key switch etc. Besides, safety accessories like photocells, inductive loop detectors, flashing lights or red/green traffic lights can be integrated to the system very easily.

Optima HDAB-CT Series Crash Tested Hydraulic Drop Arm Barrier is BSI PAS 68:2013 Rising Gate V/7500[N3]/80/90:0.0/2.1. zero penetration crash tested and certified.

CONSTRUCTION The arm of the barrier which is called the "crash beam" is supported by two "support columns" in both ends when closed. Both support columns and the crash beam is manufactured by welding NPU and NPI beams, constructing a robust steel structure. Steel construction is sand blasted and primer coated or hot dip galvanized, to prevent corrosion. Additionally the parts which stand above the ground level are yellow-black painted.

HYDRAULIC POWER UNIT AND CONTROL ELECTRONICS All the hydraulic components are tested at 250 bars although normal operating pressure is around 75-100 bars. Manuel hand pump is standard in HDAB-CT Series Crash Tested Hydraulic Drop Arm Barriers, therefore in case of power failure it is possible to raise and lower the barrier by manual hand pump. Coolers or heaters are can be integrated to the hydraulic power unit optionally. Control electronics utilized in hydraulic drop arm barrier is microprocessor controlled. Two keyboards with emergency stop are standard; one desktop, other being integrated in the hydraulic power unit. Motor is driven by a contactor and protected by a thermic breaker. The low current voltage required by the system is supplied by a switch mode power supply. There is a fuse for every component in the system.

HDAB-CT Series Crash Tested Hydraulic Drop Arm Barriers

Gate Barriers

HDAB-CT SERIES CRASH TESTED HYDRAULIC DROP ARM BARRIERS

www.optima.tc

Page 5: SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver

Traffic light can be integrated to prevent accidents, the traffic lights have independent lights for barrier lowered (red color) and barrier raised (green color). The lights change state automatically depending on barrier position. In addition to this, loop detector can be connected to prevent accidents. Radio control receiver, transmitter and antenna, card reader etc. can be integrated to any access control system. The crash barrier control system can be controlled remotely and connected to an external computer system via a communication link (ethernet). All the cables running in the system are color coded and numbered for easy tracking. It possible to check the position of barrier by using SCADA system or any control system.

ENVIRONMENTAL CONDITIONS AND POWER REQUIREMENT Between -20°C and +65°C, %95 non condensing humidity, 3 phase 380-415 V 50-60 Hz (or 220 V, 50-60 Hz, optional)

OPTIONAL ACCESSORIES 1. Flashing or red/green lights2. Radio control receiver, transmitter and antenna 3. Safety photocell, stand and casing4. Inductive loop detector5. Drainage pump6. Card reader system7. Hydraulic accumulator8. Uninterrupted power supply (UPS) 9. DC motor and pump10. Different colors

ARM LENGTH: From 4.5m to 8m

www.optima.tc

Page 6: SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver

TOP VIEW

FRONT VIEW

PASSAGE WAY

72° (max.)

PASSAGE WAY

www.optima.tc

FRONT VIEW

GROUND LEVEL

GROUND LEVEL

4000

CONCRETE

CONCRETE

CONCRETE

Page 7: SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver

SECURITY SYSTEMS

General DescriptionISO 9001: 2008

EN ISO 14001: 2004

Manual Drop Arm Barriers are designed especially for entrances where there is a threat of suicide vehicle attact, or for the entrances that have high security requirements. This product is preferred especially at sites where there is no electricity. Besides it’s definitely more economical when compared to hydraulic driven barriers. As the control of the manual drop arm barrier is by manpower, the vehicle traffic may slow down but from security point of view, manual drop arm barriers have the same strength as the hydraulic driven barriers.

STRUCTURE AND OPERATIONThe arm of the barrier which is called the "crash beam" is supported by two "support columns" in both ends when closed. Drive of the barrier is manual, i.e. by manpower. To ease the usage, a counterweight mechanism is used in the system. The structure is extremely strong and crash rated. Required foundation depth is around 500mm. This manual drop arm barrier requires only 15kg force to raise or lower. Therefore, the manual drop arm barrier can be used by anyone, the guard doesn’t have to be a strong person. Mechanism contain a locking unit which accepts a padlock for securing the barrier when it is in the "UP" or “DOWN” position. Steel construction is either sand blasted, 3 layer primary coated and yellow/black painted or hot dip galvanised, in order to prevent corrosion. The unit comes as one piece, which enables a very easy and quick installation.

ENVIRONMENTAL CONDITIONSBetween -20°C and +65°C, %95 non condensing humidity.

Manual Drop Arm Barriers

www.optima-engineering.com

Gate Barriers

MANUAL DROP ARM BARRIERS

Page 8: SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver

www.optima-engineering.com

SIDE VIEW (Open)

SIDE VIEW (Close)

FRONT VIEW (Open)

FRONT VIEW (Close)

4500

135

5

915

1825

210

4500

135

5

1825

210

Locking Unit

Page 9: SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver

SECURITY SYSTEMS

General DescriptionISO 9001: 2008

EN ISO 14001: 2004

Electromechanical barriers are designed for the controlled flow of traffic, especially for the parking places.

CABINET Barrier cabinet is designed to IP 55. Body font lid and top lid is manufactured from A1 Quality Steel. They are phosphate plated, painted to RAL 2004 and then furnaced. Anchoring to the floor is achieved by a galvanized anchoring plate. There are air circulation openings on the front lid which is opened by a key.

CONTROL ELECTRONICS Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver cards, safety photocells, open/close buttons, loop detectors, flashing lights etc. can be integrated to the control electronics easily. Closing the barrier can be utilized by automatic time delay facility, as well as inputs from other sources. Time delay can be adjusted between 0-50 seconds. Control electronics is mounted in a IP 65 proof plastic box, as most of the installations are made outdoors. Unit comes with a start stop button.

MOTOR AND REDUCER A high torque AC motor is utilized in the barrier. Coupled to the motor, there is a reducer with 1/62 reduction ratio. Casing of the reducer is injection aluminium, preventing formatting of rust. All the gears in the reducer (worm, spur etc.) are heat treated so that wear is reduced is to a minimum. Single row, radial contact ball bearings are utilized for smooth operation. A cooling fan exists at the back of the motor, running full time to cool the motor.

ARM Arm is aluminium with a special elliptical like cross section design. This special design enables a safety gasket to be mounted under the arm, besides increase the arm's inertia (i.e. increased durability against impact, wind force etc.) It is manufactured by a special mould, with extrusion process. On the arm, there are red phosphorescent stickers as a night time warning. Two ends of the arm is closed by aluminium coloured plastic caps.

MECHANISM WITH MANUAL OPERATION All the elements of the mechanism are manufactured on CNC machines. A 10 mm allen key is put through a hole on the outer surface of the barrier to provide manual operation by hand.

Electromechanical Barriers

www.optima-engineering.com

Gate Barriers

ELECTROMECHANICAL BARRIERS

Page 10: SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver

ENVIRONMENTAL CONDITIONS AND POWER REQUIREMENT Between -15°, and + 55°C, %95 non-condensing humidity; 220V 50-60 Hz.

OPTIONAL ACCESSORIES 1. Flashing lamp (flashes while the arm is in motion) 2. Barrier skirt (aluminium) 3. Protection bar (2" tubing, galvanized, RAL 2004 painted, furnaced) 4. Safety photocell 5. Stand and casing for safety photocell against direct sunlight, rain, snow, etc. 6. Loop detector 7. Radio receiver card 8. Transmitter 9. Antenna10. Stop sign in the middle of aluminium barrier arm11. LED light under the aluminium barrier arm

TYPE DESCRIPTION B300 3m maximum arm length, opening time approximately 3 seconds B600 6m maximum arm length, opening time approximately 6 seconds

www.optima-engineering.com

TOP VIEW

SIDE VIEW

1080

mm

Max 3000 mm (B300)Max 6000 mm (B600)

Max 3000/ 6000 mm

310mm

280mm

Page 11: SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver

�������������

������������ ������������������

� ��������������

� ������������������������������������������������������������������������������������� ���������������!��"���� ���� �����������������������������������#�������

������������ �� �������������������������������� �� ��$��%������&�'��������������(���)��*����*���+��,�����������-��������������.��������/���� ����0���!��

�������� �1��������� ������������������� ��������������������������������2���#���� ���������������������1��������������#������������������ �����������"�����������������#����������������2���������������������#������#�������'������$��������������������3�����"��������������2���������3���������������������2��������������*��4���� ���"��������������"�������"��������������������� �������������� ����0���!������ ��0��������������5������� �����������������6��6'"����������#�������������#������7$����������� ������������� � ��������������#��������������������� � �������������������������������������������� ������ ���������#�����������891�.8���������������������������� ��������������������-�����������������������������:���������������� ��������� �0�����#� ����#��������������������0�������#�������������

�������� �� ��� ���� �� ��������������������������������������� ���6�����������������������# �������� �����'������

�� �����������

�������������� �������

�����������

��������������

�������������� �������

Page 12: SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver

�������������� �������

�������

���������

Page 13: SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver

�������������

������������ ������������������

� ��������������

��������������������������� ���������������� ��������������������� ��������������������������������������������� ������������������������������������� �����������������!"���������� ���������������������������������#�������������������������$��������%�����������������������������%����������& ��������������������'���#������������� ��(��������)�������

�������������������������������������������������������� �����������������������������������������������������������������������������*����������� ��%�����$��������������������������������������������%���+����*�������������������������������������� ����������������',-�.//�������$��������*��������� ���������$�������������������������������������������������������������� �������� ��������0������������������������������$������������� ���������������� ������1��������������������������������������������� ��������������������������������������$�$����������������$������������������������������������

���� �� �������������2�������������������������3-��� ������������������������� ��'���#�������$�������������������%�������%���������������������������������������������������� ��������������� ��������������������#���������������������������2����������������������������� ����������� ������������������������������#�������������������������������������������������������%�����������������������������������������������������������4$������������/�5�6/�������

�� ��� ������

�������������� �������

�����������

�������������

��������� ��������

Page 14: SECURITY SYSTEMS Gate Barriers · Optima barriers are controlled with the help of advanced microelectronics. Barrier works with 220-240V, 50-60 Hz. Every kind of radio control receiver

����������� �����������������������������2�������5./7������8667���9�:6����5������������$��������../�;�6/�<+

����� ��������!��=�������������#�����������.��'������������������%��������������������������>��?������ ��������������������������'���#������������������� 6��-�� ���������"������������

���������������2/�� ���������� ����������������#�������������� ��(��������)�������2!"� !"��������� ����������������#�������������� ��(��������!/������

�������������� �������

�������

��������