Upload
vankhuong
View
260
Download
2
Embed Size (px)
Citation preview
AMERICA, INC.Sanitary Pumps and Equipment
serving the following industries:
313 W. Girard • Madison Heights, MI USA • 248.588.1500 • www.knollamerica.com
F o o d / b e v e r a g e • C o s m e t i C s • P h a r m a C e u t i C a l s • C h e m i C a l s
2016
ABOUT US
TABLE OF CONTENTS
KNOLL America, Inc. specializes in the engineering,
sales and service of sanitary pumps and drum
unloading equipment to all of North America. All
of our pumps have efficient, modern designs that
are easy to clean and service.
We serve sanitary applications for:
• Food and beverage
• Cosmetics
• Pharmaceuticals
• Chemicals
KNOLL America was established in 1995 and is
located in Madison Heights, Michigan (a suburb
of Detroit). Our goal is to exceed your expectations
in all areas of service.
AMERICA, INC.
313 W. Girard • Madison Heights, MI USA • FAX: 248.589.3400
248.588.1500 • www.knollamerica.com
AODD Pumps for Chemical Applications. . . . . . . . . . . 4 Food Grade AODD Pumps . . . . . . . . . . . . . . . . . . . . 10 3A Certified AODD Pumps . . . . . . . . . . . . . . . . . . . . 12 Drum Pump Motors . . . . . . . . . . . . . . . . . . . . . . . . 13 Mobile Drum Pumps . . . . . . . . . . . . . . . . . . . . . . . . 14 Food Grade Pulsation Dampeners . . . . . . . . . . . . . . . 16 Progressive Cavity Pump . . . . . . . . . . . . . . . . . . . . . 20 Centrifugal Pump. . . . . . . . . . . . . . . . . . . . . . . . . . 23 MAG Drive Centrifugal Pumps . . . . . . . . . . . . . . . . . 24 Check Valves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Plug Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Sight Glass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Probe Magnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Filter Bag Housings . . . . . . . . . . . . . . . . . . . . . . . . 34 Liquid Magnetic Filters . . . . . . . . . . . . . . . . . . . . . . 35 Liquid Filter & Strainer . . . . . . . . . . . . . . . . . . . . . . 36 Drum Unloader . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4
248.588.1500AMERICA, INC.
HOW IT WORKS AODD DIAPHRAGM PUMPS
HOW IT WORKS The compressed air introduced by the pneumatic
exchanger (A) behind one of the two diaphragms
generates compression and pushes the product into
the delivery duct (B), at the same time the opposing
diaphragm that is integral with the exchanger shaft
creates a vacuum and intakes the fluid (C). Once the
stroke has been completed, the pneumatic exchanger
diverts the compressed air behind the opposing
diaphragm and the cycle is reversed.
InSTallaTIOnDiaphragm pumps should
be mounted with provided
feet or bolted through pump
holes in frame foot.
BOXER PUMPSfor Industrial Applications
• Self-Priming
• Dry Operation
• Non-Lubricated Air
• Stall Prevention with Pneumatic Circuit
• Adjustable Flow Rate and Pressure
Max. Viscosity 10,000 CPS at 68°F
• Not all orientations available for all pump types.
248.588.1500AMERICA, INC.
5
MIDGET BOX
CUBIC 15
Intake/Delivery Connection: G 1/4” f Air Connection: G 1/8” f Max. Self-Priming: 9 feet Max. Flow Rate: 1.3 GPM Max. Head: 90 PSI Max. Air Supply Pressure: 90 PSI Max. Diameter of Passing Solids: N/A
Construction PolypropyleneMax. Viscosity 5,000 cps
MINIATURE AODD PUMPS
ITem # PumP HOuSIng DIaPHRagmS BallS Ball SeaTS unIT PRIce
CU15-PNTTP Polypropylene NBR+PTFE PTFE Polypropylene $371.00
CU15-PNTTA Polypropylene NBR+PTFE PTFE Aisi 316 $371.00
CU15-PNTTI Polypropylene NBR+PTFE PTFE PE-UHMW $371.00
CU15-PNTDP Polypropylene NBR+PTFE EPDM Polypropylene $371.00
CU15-PNTDA Polypropylene NBR+PTFE EPDM Aisi 316 $371.00
CU15-PNTDI Polypropylene NBR+PTFE EPDM PE-UHMW $371.00
CU15-ECNTTE ECTFE+CF NBR+PTFE PTFE ECTFE $600.00
CU15-ECNTTA ECTFE+CF NBR+PTFE PTFE Aisi 316 $559.00
ITem # PumP HOuSIng DIaPHRagmS BallS Ball SeaTS unIT PRIce
MID-PNTGR Polypropylene NBR+PTFE PYREX PPS-V $259.00
Other pump material combinations available. Please contact for item information and pricing.
Other pump material combinations available. Please contact for item information and pricing.
Intake/Delivery Connection: G 3/8” f Air Connection: G 3/8” f Max. Self-Priming: 9 feet Max. Flow Rate: 4.5 GPM Max. Head: 90 PSI Max. Air Supply Pressure: 90 PSI Max. Diameter of Passing Solids: 0.02”
Construction Polypropylene & HALAR (ECTE)Max. Viscosity 5,000 cps
Pricing subject to O.E.M. quantity discounting upon request.
Pricing subject to O.E.M. quantity discounting upon request.
Miniature AODD Pumps for Chemical Applications
Miniature AODD Pumps for Chemical Applications
MICROBOXER 30 Diaphragm Pumps for the chemical and paint industries
BOXER 50 Diaphragm Pumps for the chemical and paint industries
ITem # PumP HOuSIng DIaPHRagmS BallS Ball SeaTS O-RIngS SuggeSTeD PRODucT unIT PRIce
MB30-PHTTPD Polypropylene Hytrel PTFE Polypropylene EPDM Ethyl Acetate, Acetone, Acetic Acid, $270.00 Alcohol, Ammonia
MB30-PHTTPV Polypropylene Hytrel PTFE Polypropylene Viton Hydrochloric Acid, Nitric Acid, $270.00 Sulphuric Acid, Hydrogren Peroxide
MB30-FMTTFV PVDF Santoprene PTFE PTFE Viton Chromic Acid, Sulphuric Acid, Sodium $592.00 Hypochlorite, Hydrogen Peroxide
MB30-FMTTFT PVDF Santoprene PTFE PVDF PTFE Hydrofluoric Acid, Nitric Acid, $610.00 Halogenated Solvents
MB30-PD-DID Polypropylene EPDM EPDM PE- UHMW EPDM Water + Sand, Lime Milk $287.00
MB30-PHTAAD Polypropylene Hytrel Aisi 316 Aisi 316 EPDM Vinyl Glue $295.00
MB30-PMTTPD Polypropylene Santoprene PTFE Polypropylene EPDM Sodium Hydroxide $278.00
MB30-PHTAPV Polypropylene Hytrel+PTFE Aisi 316 Polypropylene Viton Isocyanate, Polyol $256.00
Port Size: 1/2” Max. Flow (GPM): 8 Max. Pressure: 90 PSI Max. Solid Size: 1/16” Max. Self Priming: 15 ft.
Max. operating temperature 95ºC/203ºF
AISI 316 PP PVDF
MICROBOXER
6
ITem # PumP HOuSIng DIaPHRagmS BallS Ball SeaTS O-RIngS SuggeSTeD PRODucT unIT PRIce
B50-PHTTPD Polypropylene Hytrel PTFE Polypropylene EPDM Ethyl Acetate, Acetone, Acetic Acid, $396.00 Alcohol, Ammonia
B50-PHTTPV Polypropylene Hytrel PTFE Polypropylene Viton Hydrochloric Acid, Nitric Acid, $396.00 Sulphuric Acid, Hydrogren Peroxide
B50-FMTTFV PVDF Santoprene PTFE PTFE Viton Chromic Acid, Sulphuric Acid, Sodium $843.00 Hypochlorite, Hydrogen Peroxide
B50-FMTTFT PVDF Santoprene PTFE PVDF PTFE Hydrofluoric Acid, Nitric Acid, $843.00 Halogenated Solvents
B50-PD-DID Polypropylene EPDM EPDM PE- UHMW EPDM Water + Sand, Lime Milk $341.00
B50-PHTAAD Polypropylene Hytrel Aisi 316 Aisi 316 EPDM Vinyl Glue $398.00 B50-PMTTPD Polypropylene Santoprene PTFE Polypropylene EPDM Sodium Hydroxide $396.00
B50-PHTAPV Polypropylene Hytrel+PTFE Aisi 316 Polypropylene Viton Isocyanate, Polyol $372.00
Port Size: 1/2” Max. Flow (GPM): 13 Max. Pressure: 90 PSI Max. Solid Size: 1/16” Max. Self Priming: 15 ft.
Max. operating temperature 95ºC/203ºF
AISI 316 PP PVDF
Other pump material combinations available. Please contact for item information and pricing.
Other pump material combinations available. Please contact for item information and pricing.
248.588.1500AMERICA, INC.
Diaphragm Pumps for the chemical and paint industries BOXER 80/81
Diaphragm Pumps for the chemical and paint industries BOXER 100
ITem # PumP HOuSIng DIaPHRagmS BallS Ball SeaTS O-RIngS SuggeSTeD PRODucT unIT PRIce
B81-PHTTPD Polypropylene Hytrel PTFE Polypropylene EPDM Ethyl Acetate, Acetone, Acetic Acid, $417.00 Alcohol, Ammonia
B81-PHTTPV Polypropylene Hytrel PTFE Polypropylene Viton Hydrochloric Acid, Nitric Acid, $417.00 Sulphuric Acid, Hydrogren Peroxide
B81-FMTTFV PVDF Santoprene PTFE PTFE Viton Chromic Acid, Sulphuric Acid, Sodium $984.00 Hypochlorite, Hydrogen Peroxide
B81-FMTTFT PVDF Santoprene PTFE PVDF PTFE Hydrofluoric Acid, Nitric Acid, $984.00 Halogenated Solvents
B81-PD-DID Polypropylene EPDM EPDM PE- UHMW EPDM Water + Sand, Lime Milk $384.00
B81-PHTAAD Polypropylene Hytrel Aisi 316 Aisi 316 EPDM Vinyl Glue $439.00
B81-PMTTPD Polypropylene Santoprene PTFE Polypropylene EPDM Sodium Hydroxide $417.00
B81-PHTAPV Polypropylene Hytrel+PTFE Aisi 316 Polypropylene Viton Isocyanate, Polyol $411.00
Port Size: 1/2” Max. Flow (GPM): 26 Max. Pressure: 90 PSI Max. Solid Size: 1/8” Max. Self Priming: 15 ft.
Max. operating temperature 95ºC/203ºF
AISI 316 PP PVDF
ITem # PumP HOuSIng DIaPHRagmS BallS Ball SeaTS O-RIngS SuggeSTeD PRODucT unIT PRIce
B100-PHTTPD Polypropylene Hytrel PTFE Polypropylene EPDM Ethyl Acetate, Acetone, Acetic Acid, $556.00 Alcohol, Ammonia
B100-PHTTPV Polypropylene Hytrel PTFE Polypropylene Viton Hydrochloric Acid, Nitric Acid, $556.00 Sulphuric Acid, Hydrogren Peroxide
B100-FMTTFV PVDF Santoprene PTFE PTFE Viton Chromic Acid, Sulphuric Acid, Sodium $1,435.00 Hypochlorite, Hydrogen Peroxide
B100-FMTTFT PVDF Santoprene PTFE PVDF PTFE Hydrofluoric Acid, Nitric Acid, $1,435.00 Halogenated Solvents
B100-PD-DID Polypropylene EPDM EPDM PE- UHMW EPDM Water + Sand, Lime Milk $521.00
B100-PHTAAD Polypropylene Hytrel Aisi 316 Aisi 316 EPDM Vinyl Glue $652.00
B100-PMTTPD Polypropylene Santoprene PTFE Polypropylene EPDM Sodium Hydroxide $556.00
B100-PHTAPV Polypropylene Hytrel+PTFE Aisi 316 Polypropylene Viton Isocyanate, Polyol $612.00
Port Size: 1” Max. Flow (GPM): 39 Max. Pressure: 90 PSI Max. Solid Size: 1/8” Max. Self Priming: 15 ft.
Max. operating temperature 95ºC/203ºF
AISI 316 PP PVDF
BOXER
7
Other pump material combinations available. Please contact for item information and pricing.
Other pump material combinations available. Please contact for item information and pricing.
248.588.1500AMERICA, INC.
ITem # PumP HOuSIng DIaPHRagmS BallS Ball SeaTS O-RIngS SuggeSTeD PRODucT unIT PRIce
B150-PHTTPD Polypropylene Hytrel PTFE Polypropylene EPDM Ethyl Acetate, Acetone, Acetic Acid, $777.00 Alcohol, Ammonia
B150-PHTTPV Polypropylene Hytrel PTFE Polypropylene Viton Hydrochloric Acid, Nitric Acid, $777.00 Sulphuric Acid, Hydrogren Peroxide
B150-FMTTFV PVDF Santoprene PTFE PTFE Viton Chromic Acid, Sulphuric Acid, Sodium $1,953.00 Hypochlorite, Hydrogen Peroxide
B150-FMTTFT PVDF Santoprene PTFE PVDF PTFE Hydrofluoric Acid, Nitric Acid, $1,953.00 Halogenated Solvents
B150-PD-DID Polypropylene EPDM EPDM PE- UHMW EPDM Water + Sand, Lime Milk $762.00 B150-PHTAAD Polypropylene Hytrel Aisi 316 Aisi 316 EPDM Vinyl Glue $845.00
B150-PMTTPD Polypropylene Santoprene PTFE Polypropylene EPDM Sodium Hydroxide $777.00
B150-PHTAPV Polypropylene Hytrel+PTFE Aisi 316 Polypropylene Viton Isocyanate, Polyol $825.00
BOXER 150 Diaphragm Pumps for the chemical and paint industries
BOXER 251 Diaphragm Pumps for the chemical and paint industries
ITem # PumP HOuSIng DIaPHRagmS BallS Ball SeaTS O-RIngS SuggeSTeD PRODucT unIT PRIce
B251-PHTTPD Polypropylene Hytrel PTFE Polypropylene EPDM Ethyl Acetate, Acetone, Acetic Acid, $971.00 Alcohol, Ammonia
B251-PHTTPV Polypropylene Hytrel PTFE Polypropylene Viton Hydrochloric Acid, Nitric Acid, $971.00 Sulphuric Acid, Hydrogren Peroxide
B251-FMTTFV PVDF Santoprene PTFE PTFE Viton Chromic Acid, Sulphuric Acid, Sodium $2,562.00 Hypochlorite, Hydrogen Peroxide
B251-FMTTFT PVDF Santoprene PTFE PVDF PTFE Hydrofluoric Acid, Nitric Acid, $2,562.00 Halogenated Solvents
B251-PD-DID Polypropylene EPDM EPDM PE- UHMW EPDM Water + Sand, Lime Milk $964.00
B251-PHTAAD Polypropylene Hytrel Aisi 316 Aisi 316 EPDM Vinyl Glue $1,070.00 B251-PMTTPD Polypropylene Santoprene PTFE Polypropylene EPDM Sodium Hydroxide $971.00
B251-PHTAPV Polypropylene Hytrel+PTFE Aisi 316 Polypropylene Viton Isocyanate, Polyol $1,029.00
Port Size: 1-1/4” Max. Flow (GPM): 58 Max. Pressure: 90 PSI Max. Solid Size: 13/64” Max. Self Priming: 15 ft.
Max. operating temperature 95ºC/203ºF
AISI 316 PP PVDF
Port Size: 1/2” Max. Flow (GPM): 90 Max. Pressure: 90 PSI Max. Solid Size: 15/64” Max. Self Priming: 15 ft.
Max. operating temperature 95ºC/203ºF
AISI 316 PP PVDF
BOXER
8
Other pump material combinations available. Please contact for item information and pricing.
Other pump material combinations available. Please contact for item information and pricing.
248.588.1500AMERICA, INC.
ITem # PumP HOuSIng DIaPHRagmS BallS Ball SeaTS O-RIngS SuggeSTeD PRODucT unIT PRIce
B502-PHTTPD Polypropylene Hytrel PTFE Polypropylene EPDM Ethyl Acetate, Acetone, Acetic Acid, $1,924.00 Alcohol, Ammonia
B502-PHTTPV Polypropylene Hytrel PTFE Polypropylene Viton Hydrochloric Acid, Nitric Acid, $1,924.00 Sulphuric Acid, Hydrogren Peroxide
B502-FMTTFV PVDF Santoprene PTFE PTFE Viton Chromic Acid, Sulphuric Acid, Sodium $6,522.00 Hypochlorite, Hydrogen Peroxide
B502-FMTTFT PVDF Santoprene PTFE PVDF PTFE Hydrofluoric Acid, Nitric Acid, $6,522.00 Halogenated Solvents
B502-PD-DID Polypropylene EPDM EPDM PE- UHMW EPDM Water + Sand, Lime Milk $1,765.00
B502-PHTAAD Polypropylene Hytrel Aisi 316 Aisi 316 EPDM Vinyl Glue $1,870.00
B502-PMTTPD Polypropylene Santoprene PTFE Polypropylene EPDM Sodium Hydroxide $1,924.00
B502-PHTAPV Polypropylene Hytrel+PTFE Aisi 316 Polypropylene Viton Isocyanate, Polyol $1,925.00
Diaphragm Pumps for the chemical and paint industries BOXER 502
Diaphragm Pumps for the chemical and paint industries BOXER 503
ITem # PumP HOuSIng DIaPHRagmS BallS Ball SeaTS O-RIngS SuggeSTeD PRODucT unIT PRIce
B503-PHTTPD Polypropylene Hytrel PTFE Polypropylene EPDM Ethyl Acetate, Acetone, Acetic Acid, $2,245.00 Alcohol, Ammonia
B503-PHTTPV Polypropylene Hytrel PTFE Polypropylene Viton Hydrochloric Acid, Nitric Acid, $2,245.00 Sulphuric Acid, Hydrogren Peroxide
B503-FMTTFV PVDF Santoprene PTFE PTFE Viton Chromic Acid, Sulphuric Acid, Sodium $7,485.00 Hypochlorite, Hydrogen Peroxide
B503-FMTTFT PVDF Santoprene PTFE PVDF PTFE Hydrofluoric Acid, Nitric Acid, $7,485.00 Halogenated Solvents
B503-PD-DID Polypropylene EPDM EPDM PE- UHMW EPDM Water + Sand, Lime Milk $1,890.00
B503-PHTAAD Polypropylene Hytrel Aisi 316 Aisi 316 EPDM Vinyl Glue $2,181.00
B503-PMTTPD Polypropylene Santoprene PTFE Polypropylene EPDM Sodium Hydroxide $2,245.00
B503-PHTAPV Polypropylene Hytrel+PTFE Aisi 316 Polypropylene Viton Isocyanate, Polyol $2,245.00
Port Size: 2” Max. Flow (GPM): 171 Max. Pressure: 90 PSI Max. Solid Size: 15/16” Max. Self Priming: 15 ft.
Max. operating temperature 95ºC/203ºF
AISI 316 PP PVDF
Port Size: 3” Max. Flow (GPM): 238 Max. Pressure: 90 PSI Max. Solid Size: 25/64” Max. Self Priming: 15 ft.
Max. operating temperature 95ºC/203ºF
AISI 316 PP
BOXER
9
Other pump material combinations available. Please contact for item information and pricing.
Other pump material combinations available. Please contact for item information and pricing.
PVDF
248.588.1500AMERICA, INC.
FOODBOXER 30 Diaphragm Pumps for the food industry using FDA approved elastomer
Port Size: 1/2” Max. Flow (GPM): 8 Max. Pressure: 90 PSI Max. Solid Size: 1/16” Max. Self Priming: 15 ft.
Max. operating temperature 95ºC/203ºF
FOODBOXER
10
FDAcompliant
ITem # DeScRIPTIOn PumP HOuSIng DIaPHRagmS BallS Ball SeaTS unIT PRIce
FB30-A-HTTAT Foodboxer 30, 1/2” ports AISI 316 Polished HYTREL+PTFE PTFE INOX INOX $790.00 flow rate 30 l/m
ITem # DeScRIPTIOn PumP HOuSIng DIaPHRagmS BallS Ball SeaTS unIT PRIce
FB50-A-HTTAT Foodboxer 50, 1/2” ports AISI 316 Polished HYTREL+PTFE PTFE INOX INOX $980.00 flow rate 50 l/m
FOODBOXER 50 Diaphragm Pumps for the food industry using FDA approved elastomer
Port Size: 1/2” Max. Flow (GPM): 13 Max. Pressure: 90 PSI Max. Solid Size: 1/16” Max. Self Priming: 15 ft.
Max. operating temperature 95ºC/203ºF
FDAcompliant
ITem # DeScRIPTIOn PumP HOuSIng DIaPHRagmS BallS Ball SeaTS unIT PRIce
FB80-A-HTTAT Foodboxer 80, 1” ports AISI 316 Polished HYTREL+PTFE PTFE INOX INOX $1,623.00 flow rate 100 l/m
FOODBOXER 80 Diaphragm Pumps for the food industry using FDA approved elastomer
Port Size: 1” Max. Flow (GPM): 26 Max. Pressure: 90 PSI Max. Solid Size: 1/8” Max. Self Priming: 15 ft.
Max. operating temperature 95ºC/203ºF
FDAcompliant
ITem # DeScRIPTIOn PumP HOuSIng DIaPHRagmS BallS Ball SeaTS unIT PRIce
FB100-A-HTTAT Foodboxer 100, 1” ports AISI 316 Polished HYTREL+PTFE PTFE INOX INOX $1,888.00 flow rate 30 l/m
FOODBOXER 100 Diaphragm Pumps for the food industry using FDA approved elastomer
Port Size: 1” Max. Flow (GPM): 39 Max. Pressure: 90 PSI Max. Solid Size: 1/8” Max. Self Priming: 15 ft.
Max. operating temperature 95ºC/203ºF
FDAcompliant
248.588.1500AMERICA, INC.
Diaphragm Pumps for the food industry using FDA approved elastomer FOODBOXER 503FDAcompliant
Diaphragm Pumps for the food industry using FDA approved elastomer FOODBOXER 502FDAcompliant
Diaphragm Pumps for the food industry using FDA approved elastomer FOODBOXER 251FDAcompliant
Diaphragm Pumps for the food industry using FDA approved elastomer FOODBOXER 150 Port Size: 1-1/4” Max. Flow (GPM): 58 Max. Pressure: 90 PSI Max. Solid Size: 13/64” Max. Self Priming: 15 ft.
Max. operating temperature 95ºC/203ºF
FOODBOXER
11
FDAcompliant
ITem # DeScRIPTIOn PumP HOuSIng DIaPHRagmS BallS Ball SeaTS unIT PRIce
FB150-A-HTTAT Foodboxer 150, 1-1/4” ports AISI 316 Polished HYTREL+PTFE PTFE INOX INOX $2,660.00 flow rate 220 l/m
ITem # DeScRIPTIOn PumP HOuSIng DIaPHRagmS BallS Ball SeaTS unIT PRIce
FB251-A-HTTAT Foodboxer 251, 1-1/2” ports AISI 316 Polished HYTREL+PTFE PTFE INOX INOX $3,431.00 flow rate 340 l/m
ITem # DeScRIPTIOn PumP HOuSIng DIaPHRagmS BallS Ball SeaTS unIT PRIce
FB502-A-HTTAT Foodboxer 502, 2” ports AISI 316 Polished HYTREL+PTFE PTFE INOX INOX $6,907.00 flow rate 650 l/m
ITem # DeScRIPTIOn PumP HOuSIng DIaPHRagmS BallS Ball SeaTS unIT PRIce
FB503-A-HTTAT Foodboxer 503, 3” ports AISI 316 Polished HYTREL+PTFE PTFE INOX INOX $10,400.00 flow rate 850 l/m
Port Size: 1-1/2” Max. Flow (GPM): 90 Max. Pressure: 90 PSI Max. Solid Size: 15/64” Max. Self Priming: 18 ft.
Max. operating temperature 95ºC/203ºF
Port Size: 2” Max. Flow (GPM): 171 Max. Pressure: 90 PSI Max. Solid Size: 5/16” Max. Self Priming: 12 ft.
Max. operating temperature 95ºC/203ºF
Port Size: 3” Max. Flow (GPM): 238 Max. Pressure: 90 PSI Max. Solid Size: 25/64” Max. Self Priming: 15 ft.
Max. operating temperature 95ºC/203ºF
248.588.1500AMERICA, INC.
SANIBOXER
12
FDAcompliant
ITem # DeScRIPTIOn PumP HOuSIng DIaPHRagmS BallS Ball SeaTS 0-RIngS unIT PRIce
SB100A-DTTAT Saniboxer SB100, 1-1/2 AISI 316 Polished PTFE PTFE INOX INOX PTFE $5,100.00 Clamp connections flow rate 30 GPM
FAST EMPTYING SYSTEM360º Rotation for Piping Accessibility
Easy-Clean ValvePatent System
Types of Installation
Suction/Delivery Connections: 1-1/2” Air Connection: 3/8” Max. Pressure: 90 PSI Dry Suction Capability: 12 ft.
*Negative suction installation up to 5,000 cps*Positive suction installation up to 2,000 cps
Max. flow rate: 30 GPM Max. Diameter of Solids: 1/8”
Max. operating temperature 95ºC/203ºF
248.588.1500AMERICA, INC.
Self-Priming Positive Suction Head
SANIBOXER Sanitary Diaphragm Pump for handling food and pharmaceutical fluids
FDAcompliant
ITem # DeScRIPTIOn PumP HOuSIng DIaPHRagmS BallS Ball SeaTS 0-RIngS unIT PRIce
SB251A-DTTAT Saniboxer SB251, 2” AISI 316 Polished HYTREL+PTFE PTFE Aisi 316 PTFE $7,200.00 Clamp connections flow rate 79 GPM
SB251A-HTTAT Saniboxer SB251, 2” AISI 316 Polished HYTREL+PTFE Aisi 326 Aisi 316 PTFE $7,200.00 Clamp connections flow rate 79 GPM
3A certificationpending
SANIBOXER 251 Suction/Delivery Connections: 2” CLAMP Air Connection: 1/2” G Max. Pressure: 101 PSI Dry Suction Capability: 16 ft. Max. flow rate: 79 GPM Max. Diameter of Solids: 7/32”
Max. operating temperature 95ºC/203ºF
TR
13
Drum Transfer Pumps for portable drum-transfer immersion pumping of corrosive liquids TR – MOTOR
ITem # DeScRIPTIOn mOTOR mOTOR mOTOR mOTOR FlOW RaTe VIScOSITY WeIgHT unIT POWeR VOlTage PROTecTIOn claSS (gPm) (cPS) PRIce
MOTOREEL0.5 Electric Motor 500 Watt 500 Watt 230V/115V IP 54 F 21 600 8.1 lbs. $279.00 single phase *on request
MOTOREEL0.8 Electric Motor 800 Watt 500 Watt 230V IP 54 F 23 900 8.1 lbs. $279.00 single phase
MOTORE-EL- Electric Motor 550 Watt 550 Watt 230V IP 54 F 26 600 24.3 lbs. $1,839.00JP400 w/earth cable & EX plug single phase
ITem # DeScRIPTIOn mOTOR FlOW RaTe VIScOSITY WeIgHT unIT POWeR (gPm) PRIce
MOTORE-PN-0.3 Pneumatic Motor 300 Watt 21 600 2.4 lbs. $385.00
MOTORE-PN-JPAIR1 Pneumatic Motor 300 Watt 23 400 6.6 lbs. $790.00 II 2 G Ex de IIA T6 (80ºC) X
MOTORE-PN-JPAIR3 Pneumatic Motor 400 Watt 32 600 N/A $1,132.00 II 2 G Ex de IIA T6 (80ºC) X
250 Watt 300 Watt 400 Watt
500 Watt 800 Watt 550 Watt
248.588.1500AMERICA, INC.
TR - PUMP 3 FOOT lengTH
14
PTB 03 ATEX 400X II1/2 G c IIB T4
248.588.1500AMERICA, INC.
Drum Transfer Pumps for portable drum-transfer immersion pumping of corrosive liquids Suction Hose: 1-21/32” Hose Clamp: 63/64” Total Weight: 3.0 lbs.
Max. operating temperature 60ºC/140ºF
TRP BODY PP
Drum Transfer Pumps for portable drum-transfer immersion pumping of corrosive liquids Suction Hose: 1-37/64” Hose Clamp: 63/64” Total Weight: 3.5 lbs.
Max. operating temperature 95ºC/203ºF
TRF BODY PVDF
Drum Transfer Pumps for portable drum-transfer immersion pumping of corrosive liquids Suction Hose: 1-21/32” Hose Clamp: 63/64” Total Weight: 9.5 lbs.
Max. operating temperature 95ºC/203ºF
TRA BODY AISI 316
Drum Transfer Pumps for portable drum-transfer immersion pumping of corrosive liquids Suction Hose: 1-21/32” Hose Clamp: 63/64” Total Weight: 6.6, 9.7, or 11.7 lbs.Max. operating temperature 95ºC/203ºF
TRAX BODY AISI 316
ITem# SucTIOn SHaFT BuSHIng ROTOR InTaKe PORT InTeRnal PaRTS unIT PRIce HOuSIng maTeRIal maTeRIal maTeRIal
TRPH0900 Polyproplene Hastelloy PTFE ECTFE Polyproplene Polyproplene+PTFE $368.00
TRPS0900 Polyproplene Aisi 316 PTFE ECTFE Polyproplene Polyproplene+PTFE $285.00
ITem# SucTIOn SHaFT BuSHIng ROTOR InTaKe PORT InTeRnal PaRTS unIT PRIce HOuSIng maTeRIal maTeRIal maTeRIal
TRFH0900 PVDF Hastelloy PTFE ECTFE ECTFE PVDF+PTFE $647.00
ITem# SucTIOn SHaFT BuSHIng ROTOR InTaKe PORT InTeRnal PaRTS unIT PRIce HOuSIng maTeRIal maTeRIal maTeRIal
TRA0900 Aisi 316 Aisi 316 PTFE ECTFE ECTFE PVDF+PPS-V $480.00
ITem# SucTIOn SHaFT BuSHIng ROTOR InTaKe PORT InTeRnal PaRTS unIT PRIce HOuSIng maTeRIal maTeRIal maTeRIal
TRAX0900 Aisi 316 Aisi 316 PTFE ECTFE ECTFE PVDF+PPS-V $480.00
4 FOOT lengTH TR – PUMP
15
248.588.1500AMERICA, INC.
Drum Transfer Pumps for portable drum-transfer immersion pumping of corrosive liquids
PTB 03 ATEX 400X II1/2 G c IIB T4
Drum Transfer Pumps for portable drum-transfer immersion pumping of corrosive liquids
Max. operating temperature 60ºC/140ºF
TRP BODY PP
Drum Transfer Pumps for portable drum-transfer immersion pumping of corrosive liquids
Max. operating temperature 95ºC/203ºF
TRF BODY PVDF
Drum Transfer Pumps for portable drum-transfer immersion pumping of corrosive liquids
Max. operating temperature 95ºC/203ºF
TRA BODY AISI 316
Drum Transfer Pumps for portable drum-transfer immersion pumping of corrosive liquids
Max. operating temperature 95ºC/203ºF
TRAX BODY AISI 316
ITem# SucTIOn SHaFT BuSHIng ROTOR InTaKe PORT InTeRnal PaRTS unIT PRIce HOuSIng maTeRIal maTeRIal maTeRIal
TRPH1200 Polyproplene Hastelloy PTFE ECTFE Polyproplene Polyproplene+PTFE $368.00
TRPS1200 Polyproplene Aisi 316 PTFE ECTFE Polyproplene Polyproplene+PTFE $285.00
ITem# SucTIOn SHaFT BuSHIng ROTOR InTaKe PORT InTeRnal PaRTS unIT PRIce HOuSIng maTeRIal maTeRIal maTeRIal
TRFH1200 PVDF Hastelloy PTFE ECTFE ECTFE PVDF+PTFE $647.00
ITem# SucTIOn SHaFT BuSHIng ROTOR InTaKe PORT InTeRnal PaRTS unIT PRIce HOuSIng maTeRIal maTeRIal maTeRIal
TRA1200 Aisi 316 Aisi 316 PTFE ECTFE ECTFE PVDF+PPS-V $480.00
ITem# SucTIOn SHaFT BuSHIng ROTOR InTaKe PORT InTeRnal PaRTS unIT PRIce HOuSIng maTeRIal maTeRIal maTeRIal
TRAX1200 Aisi 316 Aisi 316 PTFE ECTFE ECTFE PVDF+PPS-V $480.00
Suction Hose: 1-21/32” Hose Clamp: 63/64” Total Weight: 3.7 lbs.
Suction Hose: 1-37/64” Hose Clamp: 63/64” Total Weight: 4.11 lbs.
Suction Hose: 1-21/32” Hose Clamp: 63/64” Total Weight: 11.6 lbs.
Suction Hose: 1-21/32” Hose Clamp: 63/64” Total Weight: 6.6, 9.7, or 11.7 lbs.
PULSATION DAMPENERSPULSATION DAMPENERS
16
248.588.1500AMERICA, INC.
FeaTuReS• Available in PP, PVDF, PPS-V, AISI 316
• Automatic dampening control
• Suitable for demanding applications
• Use in potentially-explosive atmospheres (ATEX certifications)
• Use in environments subject to high humidity
• Actuated using non lubricated air
• Range of construction materials ensures correct fluid compatibility
• User-friendly parts replacement and maintenance
• Excellent performance and value for money
HOW IT WORKSThe compressed air entering the back-pressure chamber behind the diaphragm creates a pneumatic cushion that adjusts automatically to compensate the shock produced by the pressure pulse of the fluid generated by the pump.
EQUAFLUX automatic diaphragm pulsation dampeners feature solid build and high performance. They are fitted to the discharge line of diaphragm pumps in order to smooth pulsating flows and can be used with liquids having high apparent viscosity even if containing suspended solids of considerable size.
EQUAFLUX dampeners automatically adapt to system conditions without the need for manual adjustment or calibration. The ability to minimise pulsations, vibrations and water hammer means that this component pro-vides excellent protection and smooth system flow. The huge choice of construction materials allows selection of optimum chemical compatibility with the fluid and/or environment without neglecting the temperature range. Dampeners are also available for use in poten-tially explosive atmospheres (ATEX certification).
Air supply
Delivery
Intake
248.588.1500AMERICA, INC.
17
PRODucT aIR cOnnecTIOn maX. aIR SuPPlY WeIgHT OPeRaTIOn DImenSIOn unIT PRIce ITem # cOnnecT (IncHeS) PReSSuRe (PSI) aPPlIcaBIlITY (lBS.) TemP. (IncHeS) EQ303P-HT G 3” 5/16” 101 BOXER 503 PP 50.7 min+37ºF 15.6x20.4 $1,338.00 max. 149ºF
EQ303FC-MT G 3” 5/16” 101 BOXER 503 PVDF 62.8 min+37ºF 15.6x20.5 $4,636.00 max. 203ºF
EQUAFLUX 303PP PVDF
PULSATION DAMPENERS
EQUAFLUX FOOD AISI 316
PRODucT aIR cOnnecTIOn maX. aIR SuPPlY WeIgHT OPeRaTIOn DImenSIOn unIT PRIce ITem # cOnnecT (IncHeS) PReSSuRe (PSI) aPPlIcaBIlITY (lBS.) TemP. (IncHeS) FQ051A-HT G 1/2” 3/13” 101 FOODBOXER 30 – min+37ºF 5.2x4.6 $364.00 max. 203ºF
FQ100A-HT G 1” 3/13” 101 FOODBOXER 50 – min+37ºF 7.2x5.9 $640.00 and 80 max. 203ºF
FQ200A-HT G 1-1/2” 3/13” 101 FOODBOXER 100, – min+37ºF 10.3x10 $1,033.00 BOXER 80 Aisi 316 max. 203ºF
FQ302A-HT G 2” 5/16” 101 FOODBOXER 502 – min+37ºF 14x13.9 $3,394.00 max. 203ºF
FQ 51 FQ 100 FQ 200 FQ 302
Automatic Diaghragm Pulsation Dampener for demanding & high viscosity applications
Automatic Diaghragm Pulsation Dampener for demanding & high viscosity applications
PRODucT aIR cOnnecTIOn maX. aIR SuPPlY WeIgHT OPeRaTIOn DImenSIOn unIT PRIce ITem # cOnnecT (IncHeS) PReSSuRe (PSI) aPPlIcaBIlITY (lBS.) TemP. (IncHeS) EQ051P-HT G 3/4” 3/13” 101 MIDGETBOX PP, 1.1 min+37ºF 4.7x4.6 $121.00 MICROBOXER PP max. 149ºF
EQ051FC-MT G 3/4” 3/13” 101 MICROBOXER PVDF 1.1 min+37ºF 4.7x4.6 $162.00 and Aisi 316 max. 203ºF
EQ051A-HT G 1/2” 3/13” 101 MICROBOXER – min+37ºF 5.3x4.6 $364.00 Aisi max. 203ºF
EQUAFLUX 51 Automatic Diaghragm Pulsation Dampener for demanding & high viscosity applications
PP PVDF AISI
PULSATION DAMPENERS
18
248.588.1500AMERICA, INC.
EQUAFLUX 100 Automatic Diaghragm Pulsation Dampener for demanding & high viscosity applications
PRODucT aIR cOnnecTIOn maX. aIR SuPPlY WeIgHT OPeRaTIOn DImenSIOn unIT PRIce ITem # cOnnecT (IncHeS) PReSSuRe (PSI) aPPlIcaBIlITY (lBS.) TemP. (IncHeS) EQ100P-HT G 1” 3/13” 101 BOXER 50 PP, 3.3 min+37ºF 7x6.7 $181.00 BOXER 81 PP max. 149ºF
EQ100FC-MT G 1” 3/13” 101 MINIBOXER Aisi 316, 3.7 min+37ºF 7x6.8 $333.00 BOXER 50 PVDF, max. 203ºF BOXER 80 Aisi 316
EQ100A-HT G 1” 3/13” 101 MICROBOXER Aisi 316, – min+37ºF 7.2x6 $640.00 BOXER 80 Aisi 316 max. 203ºF
PP PVDF AISI
Automatic Diaghragm Pulsation Dampener for demanding & high viscosity applications EQUAFLUX 200PULSATION DAMPENERS
19
248.588.1500AMERICA, INC.
PRODucT aIR cOnnecTIOn maX. aIR SuPPlY WeIgHT OPeRaTIOn DImenSIOn unIT PRIce ITem # cOnnecT (IncHeS) PReSSuRe (PSI) aPPlIcaBIlITY (lBS.) TemP. (IncHeS) EQ200P-HT G 1-1/2” 3/13” 101 BOXER 100 PP, 8.3 min+37ºF 11.1x10 $329.00 BOXER 150 PP, max. 149ºF BOXER 251 PP
EQ200FC-MT G 1-1/2” 3/13” 101 BOXER 100 PVDF 9.9 min+37ºF 11.1x11 $592.00 and Aisi 316, max. 203ºF BOXER 150 PVDF and Aisi 316, BOXER 251 PVDF and Aisi 316
EQ200A-HT G 1-1/2” 3/13” 101 BOXER 150 Aisi, – min+37ºF 10.4x10 $1,033.00 BOXER 251 Aisi, max. 203ºF BOXER 100 Aisi
PP PVDF AISI
Automatic Diaghragm Pulsation Dampener for demanding & high viscosity applications EQUAFLUX 302PP PVDF AISI
PRODucT aIR cOnnecTIOn maX. aIR SuPPlY WeIgHT OPeRaTIOn DImenSIOn unIT PRIce ITem # cOnnecT (IncHeS) PReSSuRe (PSI) aPPlIcaBIlITY (lBS.) TemP. (IncHeS) EQ302P-HT G 2” 5/16” 101 BOXER 502 in PP 50.7 min+37ºF 15.6x20.3 $1,276.00 max. 203ºF
EQ302FC-MT G 2” 5/16” 101 BOXER 503 in PVDF 62.8 min+37ºF 15.6x20.4 $4,555.00 max. 203ºF
EQ302A-HT G 2” 5/16” 101 BOXER 502 Aisi 70.5 min+37ºF 14x13.9 $2,901.00 max. 203ºF
PROGRESSIVE CAVITY PUMP
20
248.588.1500AMERICA, INC.
PROGRESSIVE CAVITY PUMP MX For Sanitary Applications
FeaTuReS• Compatible with CIP and SIP• Hygienic design• Design with minimal dead space• Extremely easy to service• Intelligent interfaces
mODulaR DeSIgnThe modular design of the MX makes it suitable for numerous applications and extremely easy to maintain. The wide variety of components enable the pump to be modified in the optimum way to suite customers’ specific applications.
PeRFecT FOR PumPIng THe FOllOWIng FluIDS • Viscous • Thixotropic • Shear Sensitive • Abrasive • Solids in Suspension • Corrosive
Modular designClamping closure
Non-slipconnectingelements
Low clearancevolume design Intelligent
interfaces
EvenWall®Prepared
for heatingUniversal
joint sleeve
Spacioussealing
chamberBearing housing sealed
on both sides
DeSIgn FeaTuReS
aDVanTageS• 10 bar per pressure stage thanks to EvenWall®
technology• Compact assembly length at high pressures• Low-impact product delivery• Quick and easy to clean• Captive connecting elements• Modular design• Outstanding stability under pressure
• Greatest Flow Rate: Up to 26,500 Gallons per hour• Highest Pressure: 580 P.S.I. standard - 1,150 P.S.I. on selected models• Largest Solids handling: Soft pieces up to 3” in diameter without damage
PeRFORmance caPaBIlITIeS
PROGRESSIVE CAVITY PUMP MXPROGRESSIVE CAVITY PUMP
21
248.588.1500AMERICA, INC.
For Sanitary Applications
PeRFORmance PRESSURE BOOSTPump for 1,160 P.S.I. Application.
HOPPERFor pumping high viscous liquids.
DOUBLE JACKETEDFor temperature regulation
with water or oil.
SUCTIONFor high vacuum applications requiring suction lift up to 28 ft.
SUBMERGEDFor emptying bins, drums, mixers and large product bags up to 60 G.P.M.
FRee PaSSage mODel FlOW (gPH) (IncHeS)
MX 20 1,480 .87 MX 30 5,284 1.89 MX 50 26,500 3.00
All Models 580 P.S.I. Standard
For pricing, fill out the checklist on the next page for a Progressive Cavity Pump quotation.
PROGRESSIVE CAVITY PUMP
22
248.588.1500AMERICA, INC.
PROGRESSIVE CAVITY PUMP MX For Sanitary Applications
cHecKlIST
cOnTacT DeTaIlS
Company
Address
Contact Person
Telephone / E-mail /
PROceSS DeScRIPTIOn
PRODucT SPecIFIcaTIOn
Medium
Flow rate (GPH)
Viscosity (cP)
Density (kg/dm3)
Temperature (ºF)
Concentration (%)
Particle size (inches)
Discharge pressure (PSI)
Inlet pressure (PSI)
Arrangement
Regulations
Cleaning M CIP M SIP M Manual
Medium
Temperature (ºF)
Concentration (%)
Comments
23
CENTRIFUGAL PUMP SANITARY NON-SELF PRIMINGCENTRIFUGAL PUMP248.588.1500
AMERICA, INC.
maX. maX. mODel HP R.P.m. InleT SIZe OuTleT SIZe FlOW RaTe @ DIScHaRge (Head)
KN25/2 1 3500 2” 1-1/2” 57 GPM @ 20 ft. KN25/3 1-1/2” 3500 2” 1-1/2” 48 GPM @ 48 ft. KN25/4 2 3500 2” 1-1/2” 40 GPM @ 60 ft.
FOR THe FOOD, BReWeRY anD BeVeRage InDuSTRYexcellent Pump for c.I.P. ServiceNon self-priming centrifugal pumps for applications involving low viscosity liquids similar to water. The pumps are 316 series stainless steel, semi-open impeller with quick release clamp. Pumps feature a hygienic chamfered O-ring and mechanical seal. The O-ring and mechanical elastomers are NBR material standard. The pump hous-ing is machined with a drainage connection. The pumps are mounted onto NEMA wash down motors. The cart-mounted version includes an electric control with breaker and 12 feet of cable.
Optional features quoted separately upon request: • Explosion proof motors • O-ring and seal materials: EPDM, FKM • Discharge ball or butterfly valve • Diaphragm drainage valve • Drainage valve • Stainless steel motors • Discharge check valve and plug valve • Trimmed impeller • Alternative connections
Pending
DeSIgn FeaTuReSFlow Rate Max.: 65 G.P.M.Discharge Head Max.: 65 ft.Operating Temperature Max.: 265ºFOperating Pressure Max.: 150 P.S.I.
mODel PRIcIng PumP & mOBIle PumP mODel mOTOR OnlY WITH cOnTROl & caBle
KN25/2 $1,875.00 $3,275.00 KN25/3 $1,955.00 $3,355.00 KN25/4 $2,130.00 $3,530.00
FlOW cHaRacTeRISTIcS Kn25
01360131012601210116011101060101096091086
75
65
55
42
30
18
6
FEET
GALLONS PER MINUTE
22 44 66
2
3
42
3
4
HorsepowerRequirements
1 H.P
1-1/2 H.P.
2 H.P.
Voltage 460 – 3 phase
PumP PeRFORmance TaBle mODel FlOW @ HeaD In FeeT
KN25/2 31 40 44 36 57 20 KN25/3 26 55 35 54 48 48 KN25/4 22 66 29 62 40 60
MAG DRIVE CENTRIFUGAL PUMPS
24
248.588.1500AMERICA, INC.
These pumps are suitable for various applications in the chemical, plating and water treatment fields. Simplicity of design insures the minimum compo-nents for cost and ease of repair. The elimination of the shaft seal limits liquid leakage of aggressive fluids due to the lack of component wear.
OPERATION AND INSTALLATION
Pumps cannot be operated in dry run condition. They are designed for clean liquids only. Dirty or contaminated fluids can reduce pump life. Pump should be mounted horizontal and below the liquid level to prevent dry running.
Pump housing and impeller material is either polypropylene (PP) or polyvinylidene (PVDF).
Fluid Temperature: PP -50°F to 149°F PVDF -50°F to 194°F
Viscosity up to 150 CPS
1234567
Components
Shaft
Thrust bearingwasher
Bearing
O-ring
Impeller
Pump Casing
Head thrustbearing washer
MaterialAlumina Ceramics 99,7%
PTFE +30% Graphite
PTFE +30% Graphite
VITON/EPDM
PP/PVDF+CF
PP/PVDF+CF
AluminaCeramics 99,7%
MAG DRIVE CENTRIFUGAL PUMPS For Chemical Applications
MAG DRIVE CENTRIFUGAL PUMPS MAG DRIVE CENTRIFUGAL PUMPS248.588.1500
AMERICA, INC.
Options available upon request. TEFC motors, inlet and outlet flanges, and viton o-rings.
25
For Chemical Applications
CHECK VALVESDesigned for vertical installation at the bottom end of the suction pipe on both centrifugal and pneumatic pumps. These non-return valves prevent fluid from flowing out of the suction pipe. This allows the pump to remain primed at all times.
POlYPROPYleneITem # SIZe BSPP PRIce
VALVFN000012APP 1/2” $77.00
VALVFN000100APP 1” $98.00
VALVFN000114APP 1-1/4” $122.00
VALVFN000112APP 1-1/2” $215.00
VALVFN000200APP 2” $250.00
PVDFITem # SIZe BSPP PRIce
VALVFN000012AFV 1/2” $105.00
VALVFN000100AFV 1” $155.00
VALVFN000114AFV 1-1/4” $350.00
VALVFN000112AFV 1-1/2” $380.00
VALVFN000200AFV 2” $590.00
POlYPROPYleneITem # mOTOR H.P. ImPelleR (mm) InleT nTP OuTleT nTP maX HeaD In maX FlOW In PRIce male Female meTeRS g.P.m.
DM06PP 1/2 0.81 3/4” 1” 10 35 $675.00
DM10PP 3/4 0.85 1” 1-1/2” 10 55 $755.00
DM12PP 1 0.98 1” 1-1/2” 14 70 $790.00
DM14PP 2 1.08 1-1/4” 1-1/4” 15 90 $1,915.00
DM15PP 3 0.123 1-1/4” 1-1/4” 20 120 $980.00
DM30PP 5 0.134 1-1/2” 2” 25 180 $1,530.00
PVDFITem # mOTOR H.P. ImPelleR (mm) InleT nTP OuTleT nTP maX HeaD In maX FlOW In PRIce male Female meTeRS g.P.m.
DM06FC 1/2 0.81 3/4” 1” 10 35 $790.00
DM10FC 3/4 0.85 1” 1-1/2” 10 55 $1,040.00
DM12FC 1 0.98 1” 1-1/2” 14 70 $1,160.00
DM14FC 2 1.08 1-1/4” 1-1/4” 15 90 $2,520.00
DM15FC 3 0.123 1-1/4” 1-1/4” 20 120 $1,520.00
DM30FC 5 0.134 1-1/2” 2” 25 180 $2,160.00
Pump housing and impellermaterial is either polypropylene (PP) or polyvinylidene (PVDF)
PERFORMANCE CURVE
CHECK VALVES
26
248.588.1500AMERICA, INC.
CHECK VALVES – 64 SERIES
SANITARY CLAMP CHECK VALVES
BUTT-WELD CHECK VALVES
aPPlIcaTIOn Check valves, also known as “non-return valves”, are designed for use in process piping installation to prevent reverse flow.
WORKIng PRIncIPleA check valve opens when the pressure below the valve plug exceeds the pres-sure above the valve plug and the spring force. The valve closes when pressure equalization has been achieved.
STanDaRD DeSIgnThe forged stainless steel valve body ensures non-porous, smooth surfaces and dimensionally stable construction. The valve body is in two parts, assembled by means of a standard clamp and sealed with a standard gasket. The self-drain-ing design of the lower valve body enables flushing of the product. Ribbed construction of the stainless steel disc resists heavy pressure hammer, minimizes the resistance to flow and also serves as a guide to the valve plug. All seats and seals are made from FDA approved materials.
aVaIlaBle SIZeS1”, 1-1/2”, 2”, 2-1/2”, 3”, 4”
OPTIOnSEnd Connections, Sanitary Clamp, Butt-Weld, I-Line, Vitone/Silicone O-Rings and Gasket on request.
SPRIngSStronger springs are available for higher pressures.
ITem # SIZe maTeRIal Seal FInISH PRIce
K64CV104PSS 1” 304L PTFE Std (180G) $184.00
K64CV154PSS 1-1/2” 304L PTFE Std (180G) $234.00
K64CV204PSS 2” 304L PTFE Std (180G) $316.00
K64CV254PSS 2-1/2” 304L PTFE Std (180G) $464.00
K64CV304PSS 3” 304L PTFE Std (180G) $606.00
K64CV354PSS 4” 304L PTFE Std (180G) $885.00
ITem # SIZe maTeRIal Seal FInISH PRIce
K64CV106PSS 1” 316L PTFE Std (180G) $220.00
K64CV156PSS 1-1/2” 316L PTFE Std (180G) $294.00
K64CV206PSS 2” 316L PTFE Std (180G) $382.00
K64CV256PSS 2-1/2” 316L PTFE Std (180G) $561.00
K64CV306PSS 3” 316L PTFE Std (180G) $734.00
K64CV356PSS 4” 316L PTFE Std (180G) $1,068.00
ITem # SIZe maTeRIal Seal FInISH PRIce
W64CV104PSS 1” 304L PTFE Std (180G) $174.00
W64CV154PSS 1-1/2” 304L PTFE Std (180G) $231.00
W64CV204PSS 2” 304L PTFE Std (180G) $300.00
W64CV254PSS 2-1/2” 304L PTFE Std (180G) $439.00
W64CV304PSS 3” 304L PTFE Std (180G) $574.00
W64CV354PSS 4” 304L PTFE Std (180G) $838.00
ITem # SIZe maTeRIal Seal FInISH PRIce
W64CV106PSS 1” 316L PTFE Std (180G) $209.00
W64CV156PSS 1-1/2” 316L PTFE Std (180G) $278.00
W64CV206PSS 2” 316L PTFE Std (180G) $360.00
W64CV256PSS 2-1/2” 316L PTFE Std (180G) $531.00
W64CV306PSS 3” 316L PTFE Std (180G) $692.00
W64CV356PSS 4” 316L PTFE Std (180G) $1,010.00
304l SanITaRY clamP cHecK ValVeS 316l SanITaRY clamP cHecK ValVeS
304l BuTT-WelD cHecK ValVeS 316l BuTT-WelD cHecK ValVeS
CHECK VALVES
27
248.588.1500AMERICA, INC.
CHECK VALVES – 64 SERIES
MATERIAL Product Wetted Steel Parts: AISI 316L or AISI 304L Other Steel Parts: AISI 304
FDA SEALS O-Ring: PTFE Gasket: PTFE Optional: Vitone or Silicone
NOMINAL PRESSURE Max. Product Pressure: 150 PSI maximum (10 Bars) Standard Cracking Pressure: 0.5 PSI (0.035 Bars)
SURFACE FINISH Surface in Contact with Product: Ra </= µ in (Grit 220g) Optional: Ra </= µ in (Grit 320g)
*Electropolishing available upon request*Pressure drop/capacity diagram on request
TecHnIcal SPecIFIcaTIOnS
DImenSIOnS 1” 1-1/2” 2” 2-1/2” 3” 4”
A 3-3/4 3-3/4 4-3/64 4-13/32 4-31/32 5-3/8
B 2 2-17/32 3-1/64 3-19/32 4-11/16 5-5/64
OD 1 1-1/2 2 2-1/2 3 4
ID 7/8 1-3/8 1-7/8 2-3/8 2-55/64 3-27/32
Butt-Weld
A
B
OD
ID
1” 1½” 2” 2 ½” 3” 4”
2
1
7/8
2 17/32
1 ½
1 3/8
3 1/64
2
1 7/8
3 19/32
2 ½
2 3/8
4 11/16
3
2 55/64
5 5/64
4
3 27/32
3 3/4 3 3/4 4 3/64 4 13/32 4 31/32 5 3/8
Dimensions
Butt-W eld
A
ODID
B
DImenSIOnS 1” 1-1/2” 2” 2-1/2” 3” 4”
A 3-3/4 3-3/4 4-3/64 4-13/32 4-31/32 5-3/8
B 2 2-17/32 3-1/64 3-19/32 4-11/16 5-5/64
ID 7/8 1-3/8 1-7/8 2-3/8 2-55/64 3-27/32
DImenSIOnSSanitary clamp
PLUG VALVES – 11 SERIES
28
248.588.1500AMERICA, INC.
SanITaRY clamP Plug ValVe 304l
BODYITem # SIZe maT. Seal FInISH cOnFIg. PRIce
K11PV104ES2 1” 304L EPDM Std (180G) 2-WAY $360.00
K11PV154ES2 1-1/2” 304L EPDM Std (180G) 2-WAY $502.00
K11PV204ES2 2” 304L EPDM Std (180G) 2-WAY $637.00
K11PV254ES2 2-1/2” 304L EPDM Std (180G) 2-WAY $976.00
K11PV304ES2 3” 304L EPDM Std (180G) 2-WAY $1,923.00
K11PV404ES2 4” 304L EPDM Std (180G) 2-WAY $2,772.00
K11PV104ES3 1” 304L EPDM Std (180G) 3-WAY $413.00
K11PV154ES3 1-1/2” 304L EPDM Std (180G) 3-WAY $542.00
K11PV204ES3 2” 304L EPDM Std (180G) 3-WAY $694.00
K11PV254ES3 2-1/2” 304L EPDM Std (180G) 3-WAY $1,125.00
K11PV304ES3 3” 304L EPDM Std (180G) 3-WAY $1,690.00
K11PV404ES3 4” 304L EPDM Std (180G) 3-WAY $2,772.00
SanITaRY clamP Plug ValVe 316l
BODYITem # SIZe maT. Seal FInISH cOnFIg. PRIce
K11PV106ES2 1” 316L EPDM Std (180G) 2-WAY $437.00
K11PV156ES2 1-1/2” 316L EPDM Std (180G) 2-WAY $605.00
K11PV206ES2 2” 316L EPDM Std (180G) 2-WAY $769.00
K11PV256ES2 2-1/2” 316L EPDM Std (180G) 2-WAY $1,178.00
K11PV306ES2 3” 316L EPDM Std (180G) 2-WAY $1,800.00
K11PV406ES2 4” 316L EPDM Std (180G) 2-WAY $3,349.00
K11PV106ES3 1” 316L EPDM Std (180G) 3-WAY $498.00
K11PV156ES3 1-1/2” 316L EPDM Std (180G) 3-WAY $654.00
K11PV206ES3 2” 316L EPDM Std (180G) 3-WAY $836.00
K11PV256ES3 2-1/2” 316L EPDM Std (180G) 3-WAY $1,355.00
K11PV306ES3 3” 316L EPDM Std (180G) 3-WAY $2,039.00
K11PV406ES3 4” 316L EPDM Std (180G) 3-WAY $4,101.00
SANITARY BUTT-WELD PLUG VALVESanITaRY BuTT-WelD Plug ValVe 304l
BODYITem # SIZe maT. Seal FInISH cOnFIg. PRIce
W11PV104ES2 1” 304L EPDM Std (180G) 2-WAY $340.00
W11PV154ES2 1-1/2” 304L EPDM Std (180G) 2-WAY $479.00
W11PV204ES2 2” 304L EPDM Std (180G) 2-WAY $605.00
W11PV254ES2 2-1/2” 304L EPDM Std (180G) 2-WAY $929.00
W11PV304ES2 3” 304L EPDM Std (180G) 2-WAY $1,415.00
W11PV404ES2 4” 304L EPDM Std (180G) 2-WAY $2,634.00
W11PV104ES3 1” 304L EPDM Std (180G) 3-WAY $392.00
W11PV154ES3 1-1/2” 304L EPDM Std (180G) 3-WAY $510.00
W11PV204ES3 2” 304L EPDM Std (180G) 3-WAY $653.00
W11PV254ES3 2-1/2” 304L EPDM Std (180G) 3-WAY $1,063.00
W11PV304ES3 3” 304L EPDM Std (180G) 3-WAY $1,600.00
W11PV404ES3 4” 304L EPDM Std (180G) 3-WAY $3,219.00
SanITaRY BuTT-WelD Plug ValVe 316l
BODYITem # SIZe maT. Seal FInISH cOnFIg. PRIce
W11PV106ES2 1” 316L EPDM Std (180G) 2-WAY $414.00
W11PV156ES2 1-1/2” 316L EPDM Std (180G) 2-WAY $573.00
W11PV206ES2 2” 316L EPDM Std (180G) 2-WAY $733.00
W11PV256ES2 2-1/2” 316L EPDM Std (180G) 2-WAY $1,118.00
W11PV306ES2 3” 316L EPDM Std (180G) 2-WAY $1,709.00
W11PV406ES2 4” 316L EPDM Std (180G) 2-WAY $3,181.00
W11PV106ES3 1” 316L EPDM Std (180G) 3-WAY $473.00
W11PV156ES3 1-1/2” 316L EPDM Std (180G) 3-WAY $619.00
W11PV206ES3 2” 316L EPDM Std (180G) 3-WAY $792.00
W11PV256ES3 2-1/2” 316L EPDM Std (180G) 3-WAY $1,282.00
W11PV306ES3 3” 316L EPDM Std (180G) 3-WAY $1,931.00
W11PV406ES3 4” 316L EPDM Std (180G) 3-WAY $3,889.00
SANITARY CLAMP PLUG VALVE
PLUG VALVES – 11 SERIES
29
248.588.1500AMERICA, INC.
aPPlIcaTIOn Stainless steel hygienic plug valves are used in the food, dairy and chemical industries. Plug valves are used in installations where a sanitary closing or divert style valve with a minimum pressure drop is required.
STanDaRD DeSIgnThe plug valve consists of a valve body, plug and cover made from quality stainless steel. The plug is coated with a hard chrome coating followed by precision grinding and lapping to ensure leak proof and easy operation. A long, round handle allows for better leverage and smooth operation. A high degree of taper on the plug reduces the torque required to open or close the valve.
aVaIlaBle SIZeS1”, 1-1/2”, 2”, 2-1/2”, 3”, 4”
OPTIOnSEnd Connections, Sanitary Clamp and Butt-Weld, or others on request.
maTeRIalAISI 316L or AISI 304L
MATERIAL Product Wetted Steel Parts: AISI 316L or AISI 304L Other Steel Parts: AISI 304
FDA SEALS Rubber Parts: EPDM Thrust Washer: PTFE
NOMINAL PRESSURE Max. Product Pressure: 58 PSI maximum (4 Bars) Test pressure 70 PSI (5 Bars) (Leakage test according to BS EN 12266-1
SURFACE FINISH Surface in Contact with Product: Ra </= 25 µ in (Grit 220g) Optional: Ra </= 15 µ in (Grit 320g) upon request
CONNECTIONS OPTIONAL Sanitary Clamp (ISO 2852/BS 4825-3) Butt Weld (ISO 2037/BS 4825-1) I-Line upon request
TecHnIcal SPecIFIcaTIOnS PLUG VALVE SPECIFICATIONS
Butt-Weld
DImenSIOnS 1” 1-1/2” 2” 2-1/2” 3” 4”
A 4-9/16 5-13/16 6-13/16 8-1/4 9-7/16 11-13/16
B 3-35/64 4-39/64 6-11/16 5-19/32 6-1/16 6-25/32
C 3-15/16 4-17/32 4-13/16 6-19/64 8 8-17/64
OD 1 1-1/2 2 2-1/2 3 4
ID 7/8 1-3/8 1-7/8 2-3/8 2-55/64 3-27/32
L 2-15/32 3-11/64 3-11/32 3-15/16 4-17/32 5-14/32
D 1-27/64 1-13/16 2-9/64 2-43/64 2-3/4 2-13/16
DImenSIOnS 1” 1-1/2” 2” 2-1/2” 3” 4”
A 4-9/16 5-13/16 6-13/16 8-1/4 9-7/16 11-13/16
B 3-35/64 4-39/64 6-11/16 5-19/32 6-1/16 6-25/32
C 3-15/16 4-17/32 4-13/16 6-19/64 8 8-17/64
ID 7/8 1-3/8 1-7/8 2-3/8 2-55/64 3-27/32
L 2-9/32 2-29/32 3-13/32 4-1/8 4-23/32 5-29/32
D 1-27/64 1-13/16 2-9/64 2-43/64 2-3/4 2-13/16
DImenSIOnS
Sanitary clamp
SIGHT GLASS
30
248.588.1500AMERICA, INC.
SIGHT GLASS – 95 SERIES
SanITaRY clamP SIgHT glaSS 304lITem # SIZe maTeRIal Seal FInISH TuBe guaRD PRIce
K955G104PSSLWG 1” 304L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $140.00
K955G154PSSLWG 1-1/2” 304L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $166.00
K955G204PSSLWG 2” 304L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $185.00
K955G254PSSLWG 2-1/2” 304L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $237.00
K955G304PSSLWG 3” 304L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $307.00
K955G404PSSLWG 4” 304L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $405.00
SanITaRY clamP SIgHT glaSS 316lITem # SIZe maTeRIal Seal FInISH TuBe guaRD PRIce
K955G106PSSLWG 1” 316L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $168.00
K955G156PSSLWG 1-1/2” 316L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $197.00
K955G206PSSLWG 2” 316L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $218.00
K955G256PSSLWG 2-1/2” 316L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $282.00
K955G306PSSLWG 3” 316L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $361.00
K955G406PSSLWG 4” 316L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $475.00
SANITARY BUTT-WELD SIGHT GLASSSanITaRY BuTT-WelD SIgHT glaSS 304lITem # SIZe maTeRIal Seal FInISH TuBe guaRD PRIce
W955G104PSSLWG 1” 304L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $132.00
W955G154PSSLWG 1-1/2” 304L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $158.00
W955G204PSSLWG 2” 304L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $177.00
W955G254PSSLWG 2-1/2” 304L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $228.00
W955G304PSSLWG 3” 304L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $291.00
W955G404PSSLWG 4” 304L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $384.00
SanITaRY BuTT-WelD SIgHT glaSS 316lITem # SIZe maTeRIal Seal FInISH TuBe guaRD PRIce
W955G106PSSLWG 1” 316L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $159.00
W955G156PSSLWG 1-1/2” 316L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $187.00
W955G206PSSLWG 2” 316L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $208.00
W955G256PSSLWG 2-1/2” 316L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $269.00
W955G306PSSLWG 3” 316L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $343.00
W955G406PSSLWG 4” 316L PTFE Std (180G) Food Grade Polycarbonate (Lexan)/Std. Polycarbonate $453.00
STANDARDSIGHT GLASS
GUARDEDSIGHT GLASS
SIGHT GLASS
31
248.588.1500AMERICA, INC.
aPPlIcaTIOn Inline sight glasses are used in pipelines for visual observation of product flow.
WORKIng PRIncIPle Once the sight glass is installed, inline product will flow through the inside of the unit allowing for easy visual examination of liquid flow.
STanDaRD DeSIgnThe food grade polycarbonate tube is as clear as glass and it is unbreakable under normal use. It is mounted under two forged stainless steel studs and nuts. The forged stainless steel flanges ensure non porous, smooth surface and dimensionally stable construction.
aVaIlaBle SIZeS1”, 1-1/2”, 2”, 2-1/2”, 3”, 4”
OPTIOnSBorosilicate glass tubeEnd Connections: Sanitary Clamp and Butt-WeldGuard: The outer polycarbonate guard protects the inner glass from being broken or damaged.
FDa Seal maTeRIalStandard: PTFE/Silicone (Combo)
MATERIAL Product Wetted Steel Parts: AISI 316L or AISI 304L
FDA SEALS Standard: PTFE/Silicone (Combo)
TUBE Standard: Food grade polycarbonate (Lexan) Optional: Borosilicate Glass
NOMINAL PRESSURE Max. Product Pressure: 10 bar maximum (145 PSI) (Lexan) 10 bar maximum (145 PSI) (Borosilicate) Working Temperature: 215º Fahrenheit max. (Lexan) 350º Fahrenheit max. (Borosilicate)
SURFACE FINISH Surface in Contact with Product: Ra </= 23 µ in (Grit 180g) Optional: Ra </= 16 µ in (Grit 240g) Ra </= 10 µ in (Grit 320g)
CONNECTIONS OPTIONAL Sanitary Clamp (ISO 2852/BS 4825) Butt Weld (ISO 2037/BS 4825) I-Line upon request
TecHnIcal SPecIFIcaTIOnS
Butt-Weld
DImenSIOnS 1” 1-1/2” 2” 2-1/2” 3” 4”
A 2-1/8 2-15/16 3-11/32 3-3/4 4-1/8 5-1/2
B 6-17/32 6-17/32 6-17/32 6-17/32 6-17/32 6-17/32
ID 7/8 1-3/8 1-7/8 2-3/8 2-55/64 3-27/32
OD 1 1-1/2 2 2-1/2 3 4
SIGHT GLASS – 95 SERIES
DImenSIOnS 1” 1-1/2” 2” 2-1/2” 3” 4”
A 2-1/8 2-15/16 3-11/32 3-3/4 4-1/8 5-1/2
B 6-17/32 6-17/32 6-17/32 6-17/32 6-17/32 6-17/32
ID 7/8 1-3/8 1-7/8 2-3/8 2-55/64 3-27/32
DImenSIOnS
Sanitary clamp
PROBE MAGNET
32
248.588.1500AMERICA, INC.
SAMPLING PROBE MAGNET – HIGH INTENSITY – RARE EARTH
SamPlIng PROBe magneTITem # lengTH l lengTH l2 lengTH l3 WeIgHT (KgS) PRIce
MSP100 100 265 395 0.9 $315.00
MSP200 200 365 495 1.2 $360.00
MSP300 300 465 595 1.6 $605.00
The High Intensity Magnetic Sampling Probe is ideal for quality control personnel to quickly and easily carry out product purity inspections on any powder, granulate or liquids for ferrous or para-magnetic contamination.
The probe should be used for sample inspection of product at inward goods, prior to despatch and at critical control points throughout the process line for batch testing.
Simply allow the processed product to pass over the magnetic section of the probe or agitate any static product. Any ferrous or paramagnetic contamination present will be highly visible when concentrated on the probes surface.
cleanIngCleaning can be conducted in seconds. Remove the unit from the sampling area and whilst holding the body of the probe simply pull the rear handle backward, this will release any attracted contami-nation enabling further analysis to be conducted.
SuITaBle PRODucTSAny powders, granulates, liquids, sauces, juices, chocolate etc.
SuITaBle lOcaTIOnSAny existing sampling points or packaged product.
BeneFITS• Easy to clean
• Simple to use
• Indicates if contamination is present
• Removes micron sized contaminants
• Meets audit requirements
• Rare Earth 9,000 Gauss
All dimensions in mm.
PROBE MAGNET
33
248.588.1500AMERICA, INC.
TecHnIcal SPecIFIcaTIOnS
SAMPLING PROBE MAGNET – HIGH INTENSITY – RARE EARTH
ITem # lengTH l lengTH l2 lengTH l3 WeIgH (KgS)
MSP100 100 265 395 0.9
MSP200 200 365 495 1.2
MSP300 300 465 595 1.6
PERFORMANCE Magnetic Performance: 9,000 Gauss High Strength Performance Reading: On tube surface Magnetic Material: Rare Earth Neodymium Iron Boron Magnet Grade: N45 – Inspected & confirmed via hystergraph prior to use Temperature: -20º C/ + 90º C
MATERIALS Tubing: 316 Grade Stainless Steel – Aerospace Quality Other Parts: 316 Grade Stainless Steel Surface Finish: Polished to 0.6µm
OPTIONS High temperature Samarium Cobalt magnetic material + 250º C Pharmaceutical specification Magnetic lengths up to 1000mm ATEX certified
All dimensions in mm.
JACKETED
High Intensity Magnetic Filtration for protection against ferrous and paramagnetic contamination
SINGLE WALL
FILTER BAG HOUSINGS
34
248.588.1500AMERICA, INC.
FILTER BAG HOUSINGS
STanDaRD FeaTuReS 304L & 316L Stainless Steel
Electro Polish Finish
Permanently Piped Vessels
Stainless Steel Restrainer Basket
3-Lug Hinged Lid
Side Inlet/Bottom Outlet
NPT or Sanitary Connections
Viton Seals
Adjujstable 304L Stainless Legs
Wall Mount Bracket Available for #4
OPTIOnal FeaTuReS Inlet/Outlet Connection Sizes
Seal Material
Vent, Gauge, Drain Ports
Drawings Available Upon Request
#4 SIZe Bag HOuSIngS (300 PSI)
ITEM # CONNECTION DESCRIPTION PRICE
00401123L010N1V4 1” NPT 304 STAINLESS STEEL $1,375.00
00401123L010N1V6 1” NPT 316 STAINLESS STEEL $1,387.00
00401123L010S1V4 1” SANITARY 304 STAINLESS STEEL $1,375.00
00401123L010S1V6 1” SANITARY 316 STAINLESS STEEL $1,387.00
00401123L010S1V6-3A 1” SANITARY USDA/3A STANDARDS $3,148.00
#1 SIZe Bag HOuSIngS (100 PSI) ITEM # CONNECTION DESCRIPTION PRICE
L0801153L015N1V4 1.5” NPT 304 STAINLESS STEEL $2,083.00
L0801153L015N1V6 1.5” NPT 316 STAINLESS STEEL $2,107.00
L0801153L015S1V4 1.5” SANITARY 304 STAINLESS STEEL $2,083.00
L0801153L015S1V6 1.5” SANITARY 316 STAINLESS STEEL $2,107.00
L0801153L015S1V6-3A 1.5” SANITARY USDA/3A STANDARDS $4,981.00
#2 SIZe Bag HOuSIngS (100 PSI) ITEM # CONNECTION DESCRIPTION PRICE
L0801303L020N1V4 2” NPT 304 STAINLESS STEEL $2,317.00
L0801303L020N1V6 2” NPT 316 STAINLESS STEEL $2,707.00
L0801303L020S1V4 2” SANITARY 304 STAINLESS STEEL $2,317.00
L0801303L020S1V6 2” SANITARY 316 STAINLESS STEEL $2,707.00
L0801303L020S1V6-3A 2” SANITARY USDA/3A STANDARDS $5,279.00
LIQUID FILTER MAGNETLIQUID FILTER MAGNET
35
248.588.1500AMERICA, INC.
StandardDesign
JacketedDesign
ITem # SPOuT DIa. a DIa. B lengTH c HeIgHT D nO. RODS WeIgHTS (Kg) unIT PRIce ILF200/50 50 200 350 200 7 22 $6,602.00
ILF200/75 75 200 350 200 7 22 $7,253.00
ILF300/50 50 300 450 300 9 36 $10,254.00
ILF300/75 75 300 450 300 9 36 $10,353.00
ILF300/100 100 300 450 300 9 36 $10,551.00
Operating temperature -4ºF/+203ºF All dimensions in mm
Mag. Performance: 9,000 Gauss High Strength Perf. Reading: On Tube Surface Mag. Material: N45 - Inspected & confirmed via hystergraph prior use Pressure: 87 PSI
PeRFORmance
Housing: 316 Grade SS Tubing: 316 Grade SS - Aerospace Quality Other Parts: 316 Grade SS Surface Finish: Brushed Internally/Externally to 1.2 um Sealing: Silicon Rubber O-ring, brown Band Clamp: 304 Grade SS
maTeRIalS
ITem # SPOuT DIa. a DIa. B lengTH c HeIgHT D nO. RODS WeIgHTS (Kg) unIT PRIce ILF200/50/J 50 200 350 200 7 22 $7,730.00
ILF200/75/J 75 200 350 200 7 22 $8,428.00
ILF300/50/J 50 300 450 300 9 36 $10, 856.00
ILF300/75/J 75 300 450 300 9 36 $11,024.00
ILF300/100/J 100 300 450 300 9 36 $11,191.00
Operating temperature -4ºF/+203ºF All dimensions in mm Price may vary due to special modification of flange connection
Suitable products: Chocolate, Molasses, Jam, Syrup, Juice, Soup, Brine, Paste’s,
Spreads and Beverages.
Double wall for heated pipe lines JACKETED
High Intensity Magnetic Filtration for protection against ferrous and paramagnetic contamination
SINGLE WALL
LIQUID FILTER & STRAINER
36
248.588.1500AMERICA, INC.
LIQUID FILTER & STRAINER 25 Series (In-line) / 24 Series (90 Angle)
aPPlIcaTIOnStainless steel filters and strainers are used in liquid flow systems for removal of various size particles.
WORKIng PRIncIPleFilters allow the removal of fine particles from various liquids. The stainless steel mesh can be reused after cleaning. Strainers are coarse filters that remove larger particles.
STanDaRD DeSIgnThe filters and strainers consist of a housing with an inlet and outlet. Inside the housing the straining element is fixed in such a way that the flow is forced through it. This element consists of a backup tube and straining mesh which is fitted between two flanges by means of a rubber gasket. The flanges clamp to the housing with a standard clamp and
Side Entry
In-Line
gasket, allowing for easy assembly and disassembly for cleaning or inspection. All seats and seals are made from FDA approved materials.
aVaIlaBle SIZeSIn-line1”, 1 ½”, 2”, 2 ½”, 3”, 4”
Side entry1”, 1 ½”, 2”, 2 ½”, 3”
OPTIOnSIn-line or side entry styles.FDA Seal Materials : Silicone (Std.), EPDM, VitonLong or Short Lengthsend connections: Sanitary ClampStraining mesh: 6-200 mesh1/4” or 1/8” holes in backup tube
LIQUID FILTER & STRAINERLIQUID FILTER & STRAINER
37
248.588.1500AMERICA, INC.
MATERIAL Product Wetted Steel Parts: AISI 316L
FDA SEALS Standard: SILICONE Optional: Viton, EPDM
NOMINAL PRESSURE Maximum Product Pressure: 117 PSI maximum (8 bars) Test Pressure: 145 PSl (10 bars)
FILTER AREA Short: 1 sq.ft. (0.65 actual) Long: 2 sq.ft. (1.94 actual)
SuRFace FInISH Surface in Contact with Product: Ra </= 23 µ in (Grit 180g) Optional: Ra </= 16 µ in (Grit 240g) Ra </= 10 µ in (Grit 320g) *Electropolishing available upon request
CONNECTIONS Sanitary Clamp (ISO 2852 / BS 4825)
TecHnIcalSPecIFIcaTIOnS
25 Series (In-line) / 24 Series (90 Angle)
meSH mIcROn RaTIng aRea BeT. WIReS % OPen WIRe SIZe
6* 3353 0.132 62.7 0.035
8* 2540 0.100 64.0 0.025
10 1095 0.075 56.3 0.025
12 1524 0.060 51.8 0.023
16 1130 0.045 50.7 0.018
20 864 0.034 46.2 0.016
30 533 0.021 40.2 0.016
40 381 0.015 36.0 0.010
50 280 0.011 30.3 0.009
60 229 0.009 30.5 0.008
80 178 0.007 31.4 0.006
100 140 0.004 37.4 0.003
150 104 0.004 37.4 0.093
200 73 0.003 33.6 0.002
*Non-standard size mesh – please consult factory for price & delivery
LIQUID FILTER & STRAINER
38
248.588.1500AMERICA, INC.
LIQUID FILTER & STRAINER 25 Series (In-line) / 24 Series (90 Angle)
SHORT a B c D e
1 15-3/4 15-15/16 12-7/16 3-1/2 4-1/2
1-1/2 15-3/4 15-15/16 12-3/16 3-1/2 4-1/2
2 15-3/4 15-15/16 11-11/16 3-1/2 4-1/2
2-1/2 15-3/4 15-15/16 11-7/16 3-1/2 4-1/2
3 15-3/4 15-15/16 11-7/16 3-1/2 4-1/2
4 NA 15-15/16 10-15/16 3-1/2 4-1/2
cla
mP
cla
mP
lOng a B c D e
1 35-3/8 35-1/2 32 3-1/2 4-1/2
1-1/2 35-3/8 35-1/2 31-3/4 3-1/2 4-1/2
2 35-3/8 35-1/2 31-1/2 3-1/2 4-1/2
2-1/2 35-3/8 35-1/2 31-1/4 3-1/2 4-1/2
3 35-3/8 35-1/2 31 3-1/2 4-1/2
4 NA 35-1/2 30-1/2 3-1/2 4-1/2
6
5
4
3
2
1
025 50 100 125 150 175 200 GPM
Pre
ssur
e D
rop
(PS
I)
PROPeR FIlTeRIng RecOmmenDaTIOnSThese filters and strainers are designed for particulate removal in liquid flow systems. They are not made to remove product impurities or odors. Effective-ness of the filter and strainers vary according to line pressure, size and amount of particles in a product, etc.
FILTER MEDIA SHOULD BE CHANGED IF THERE IS A PRESSURE DROP OF 2 TO 5 PSI OVER NORMAL PRESSURE.When using strainers or filters with a high speed or positive displacement pump, use a by-pass or pressure relief system to protect the strainers and filters.
Curve is based on waterShort version max. Flow 125 gpmLong version max. Flow 200 gpm
FIlTeR/STRaIneR PReSSuRe DROP cuRVeFor long and short units25 Series & 24 Series
LIQUID FILTER & STRAINERLIQUID FILTER & STRAINER248.588.1500
AMERICA, INC.
25 Series (In-line) / 24 Series (90 Angle)
EndConn’s Style Size Material Seals Finish Length Mesh
BackupTubeHoles
STYle 25 Inline 24 90 Angle
SIZe 10 1” 15 1.5” 20 2” 25 2.5” 30 3” 40 4”
SealS S SILICONE / Std E EPDM V Viton
FInISH S Std (180G) X 240 Grit Y 320 Grit XE 240/EP YE 320/EP
enD cOnnecTIOn K Sanitary Clamp
maTeRIal 6 AISI 316L
lengTH S Short L Long
meSH 6 * 6 Mesh 8 * 8 Mesh 10 10 Mesh 12 12 Mesh 16 16 Mesh 20 20 Mesh 24 24 Mesh 30 30 Mesh 40 40 Mesh 50 50 Mesh 60 60 Mesh 80 80 Mesh 100 100 Mesh 150 150 Mesh 200 200 Mesh
F
Type
HOleS 4 1/4” 8 1/8”
*Non-standard size mesh,call for more information.
FIlTeR & STRaIneR ORDeRIng SYSTem
Price adders for non standard finish and seals can be quoted upon request.
Price for 4” side entry strainers can be quoted upon request.
All filters include the housing, back up tube and straining mesh (10-200) size.
SHORT In-lIne FIlTeRS & STRaIneRScODe maTeRIal 1” 1.5” 2” 2.5” 3”MSP100
K-25-F 316 $1,320.00 $1,320.00 $1,320.00 $1,320.00 $1,320.00
lOng In-lIne FIlTeRS & STRaIneRScODe maTeRIal 1” 1.5” 2” 2.5” 3”MSP100
K-25-F 316 $1,530.00 $1,530.00 $1,530.00 $1,530.00 $1,530.00
SHORT 90-DegRee angle FIlTeRS & STRaIneRScODe maTeRIal 1” 1.5” 2” 2.5” 3”MSP100
K-24-F 316 $1,320.00 $1,320.00 $1,320.00 $1,320.00 $1,320.00
lOng 90-DegRee angle FIlTeRS & STRaIneRScODe maTeRIal 1” 1.5” 2” 2.5” 3”MSP100
K-24-F 316 $1,530.00 $1,530.00 $1,530.00 $1,530.00 $1,530.00
39
DRUM UNLOADER
40
248.588.1500AMERICA, INC.
ARTICULATING ARM 55-GALLON DRUM UNLOADER For Sanitary Applications
VeRSaTIle. eFFIcIenT. POWeRFul.
• Labor saving single arm with swivel for unloading 4 drums on a pallet without repositioning drums.
• Easily moved arm saves time lost in drum alignment associ-ated with traditional stationary unloaders.
• Unloaders are equipped with high volume progressive cavity pumps capable of up to 25 gallons per minute and 150 PSI.
• Pumps are perfect for highly viscous products or fluids with suspended solids.
• Pumps are excellent for accurate metering of the container contents during unloading.
• The electric driven pump is quieter and more efficient to operate than traditional air driven pumps.
WHIcH PumP IS RIgHT FOR YOu? High Viscous Product medium Viscous Submersible
Pump and following plate compress highly viscous product that is too thick to flow.
Hygienic pump capable of submersion in medium viscous liquids.
20 g.P.m.150 P.S.I.
20 g.P.m.150 P.S.I.
•Unloader must be firmly fixed to the floor to prevent tipping.
articulating arm accessory mixer for drum or vat mixing
air Operated Double Diaphragm Pump for medium to light viscosity fluids to 75 g.P.m.
For pricing on the Drum Unloader, fill out the check list on Drum Unloaders/Articulating Arms for a quotation.
ARTICULATING ARM 55-GALLON DRUM UNLOADERDRUM UNLOADER
41
248.588.1500AMERICA, INC.
For Sanitary Applications
For pricing on the Drum Unloader, fill out the check list on Drum Unloaders/Articulating Arms for a quotation.For pricing on the Drum Unloader, fill out the check list on Drum Unloaders/Articulating Arms for a quotation.
30.11in
764.80mm
AIRPANEL
19.69in500mm Sq
BASE
FOLLOWER PLATES AVAILABLE FOR
[21.5in OR 22.5in]546.1mm OR 571.5mm
BARREL DIAMETERS
15.50inR394mm
Min. Working Radius
53.15inR1350mm
Max. WorkingRadius
113.58in2885mm
26.31in
668.26mm
ELECTRICALPANEL
Labor saving single arm with swivel for unloading 4 drums on a pallet without repositioning drums.
aVaIlaBle OPTIOnS IncluDe
• Stainless Steel Motor• Variable Speed Motor• Dry Run Protection• CIP Ports• Mixer Accessory• Various Pump Options
See our Drum Unloader Videos on our website atwww.KnollAmerica.com
DRUM UNLOADER
42
248.588.1500AMERICA, INC.
STATIONARY 55-GALLON DRUM UNLOADER For Sanitary Applications
For pricing on the Drum Unloader, fill out the check list on Drum Unloaders/Articulating Arms for a quotation.
eXcellenT cHOIce FOR THe FOllOWIng ReaSOnS
• Efficient electrical energy saving over air compressor costs.
• High-viscous material pumping (e.g. peanut butter or tomato paste).
• Accurate metering of the container contents during unloading is easily accomplished.
• Faster unloading of containers at up to 60 G.P.M. and 150 P.S.I.
• Quieter operation during constant unloading periods.
aVaIlaBle OPTIOnS
• Stainless Steel Motor• Variable Speed Motor• Dry Run Protection• CIP Ports• Moveable Frame
Three methods of Pump cleaning
1. Dissassembly of entire pump.2. Pumping of cleaning solutions.3. CIP or SIP
20 g.P.m.Capable of unloading a 55 gallon drum in 3 minutes.
60 g.P.m.Capable of unloading a 55 gallon drum in less than 1 minute.
Various materials are available for following plate wipers. The standard material is FDA Silicone Rubber.
Both the 20 and the 60 G.P.M. pump models can be double jacketed which allows heating the product, resulting in increased flow ability.
ARTICULATING ARM 55-GALLON DRUM UNLOADERDRUM UNLOADER
43
248.588.1500AMERICA, INC.
For Sanitary Applications
For pricing on the Drum Unloader, fill out the check list on Drum Unloaders/Articulating Arms for a quotation.
cHecKlIST
cOnTacT DeTaIlS
Company
Address
Contact Person
Telephone / E-mail /
PROceSS DeScRIPTIOn (including number of barrels unloaded per day)
Inside Barrel Diameter (inches)
model M Articulating Arm M Stationary Unloader
PRODucT SPecIFIcaTIOn
Medium
Flow rate (GPH)
Viscosity (cP)
Temperature (ºF)
Particle size (inches)
Discharge pressure (PSI)
Cleaning M CIP M SIP M Manual
Medium
Temperature (ºF)
Concentration (%)
Options
Comments
Desired Unloading Time Per Barrel