BATTERY HOLDER

PROPERLY CRADLED IN CENTER SUPPORT

CENTER SUPPORT

CRADLE

CLICK!

CLICK!

CLICK!

CLICK!

CLICK!CLICK!

EQUALLY SPACED

2 - 5 in (51 - 127 mm)

SHADES UP TO48 in (1219 mm)

SHADESWIDER THAN

48 in (1219 mm)

2 - 5 in (51 - 127 mm)

EQUALLY SPACED

2 - 5 in (51 - 127 mm)

SHADES UP TO48 in (1219 mm)

SHADESWIDER THAN

48 in (1219 mm)

2 - 5 in (51 - 127 mm)

Roller Shade• Installation and Setup Guide—Please Read Before Installing and OperatingBattery-Powered Window Shade with RF Wireless Remote Control English

Lutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036-1299, U.S.A.

12/2013P/N 045404 Rev. B Lutron, O, Serena and Pico are registered trademarks of Lutron Electronics Co., Inc.

1 Mounting the Back Cover:

3 Hanging the shade: 2 Installing the Center Support:

2.1 Position the Center Support E midway across the mounted Back Cover as shown and lock it into the Back Cover with an audible “click.”

3.1 Rest the inner part of each end bracket (shaded below), on the lower tab of the mounted Back Cover A .

3.2 Push the top of the shade into the Back Cover, locking the brackets with an audible “click” at each end.

1.2 According to the mounting option chosen on the original order, fasten the Back Cover A , to the mounting surface using the mounting screws provided B or other appropriate fasteners.

**NOTE: Depending on the size of your shade and the depth of your trim, or the roll direction of your shade, you may be able to mount the shade directly to the wall above the trim without using the spacers.

In this arrangement, the top of the Back Cover must be a minimum of 51/4 in (133 mm) above the top of the trim.

NOTE: It is recommended that shades wider than 48 in (1219 mm) are installed by 2 persons.

TO REMOVE THE SHADE: With the shade firmly supported, press down on the release tab at the top of each end bracket.

WIDE SHADES WITH CENTER SUPPORT: The Center Support is positioned to cradle the shade’s battery holder. On wide shades, the center of the battery holder may sag during installation step 3.1, requiring you to lift it up and into the cradle as you proceed to step 3.2.

*NOTE: If your shade was ordered with Optional Fascia, the fascia will be attached at the factory and wrapped with the shade during packaging. Leave the wrapping in place during installation for added stability. After the shade is hung securely, use scissors to cut the wrap material from below the shade, then remove it by pulling it out through the top of the shade.

#2 PhillipsDriver Bit

Pencil

Level

D-Cell Alkaline Batteries(6 or 8 depending on shade size)

Power Drill

Back CoverA Mounting Screws(qty. varies with shade size)

B

Serena® Roller Shade Assembly(standard system or with optional fascia*)

Spacers (included only when outside mount above trim is specified)

D Center Support (included only with shades wider than 48 in / 1219 mm)

E

E

A

A

B

B

A

C

Outside Mount on Trim

Outside Mount above Trim

A

Align the top of the

Back Cover with the top

edge of the trim

B

B

Included in the box:

Other items you’ll need:

NOTE: The Center Support is included only with shades wider than 48 in (1219 mm). If the width of your shade is 48 in (1219 mm) or less, skip this step.

5.25 in(133 mm)

min.

Wall Regularroll

Reverseroll

Trim

Equal depth both sides

Equal space both sidesA

NOTE: Ensure the Back Cover is centered in the window opening. There must be equal space between each end and the side trim.

Inside Mount

B

B

Spacers D between the Back

Cover and the mounting surface

(included only when outside mount above

trim is specified)**

C

MOUNTINGOPTION:

MOUNTINGOPTION:

MOUNTINGOPTION:

Thank You!Congratulations on your purchase of a Serena® remote-controlled shade by Lutron®. We trust you will be delighted with the comfort and convenience these shades will bring to your home.

Be sure to register your shade(s) and share your experience with our products at www.lutron.com/serenaregistration.

As the world leader in light and shade control, we thank you for selecting Serena shades and look forward to working with you again. If you have any questions, please email us at serenashades@lutron.com or call our 24/7 customer support hotline at 888.445.8063.

Sincerely,The Lutron Serena Team

= Optional Fascia

1/8 in (3.2 mm)Drill Bit

! CAUTION: RISK OF FALLING OBJECTS. Securely install the shade system per the mounting instructions. Failure to do so could result in minor or moderate injury.

NOTE: The Back Cover features grooves to help stabilize the point of your drill bit.

1.1 Hold the Back Cover A up to the mounting surface. Approximate its final position centered on the window, and use a pencil to mark mounting screw locations on the Back Cover. To ensure the Back Cover is properly mounted, we recommend:

a. Plan to install a mounting screw 2 - 5 in (51 - 127 mm) from each end of the Back Cover.

c. Locate the mounting screws so that they drive into studs or solid trim. For surfaces other than solid wood, use appropriate expansion anchors, toggle bolts, or other fasteners (not included).

d. Verify that the mounted Back Cover is level, centered on, and parallel to, the window opening.

1.2 Pre-drill the Back Cover A at the pencil marks, using a 1/8 in (3.2 mm) drill bit.

b. For shades wider than 48 in (1219 mm), plan to install two additional mounting screws, equally spaced across the Back Cover. DO NOT install a screw at the center of the Back Cover.

Tape Measure

Open

Close

Shade All

1 2

3 4

Open

Close

Shade All

1 2

3 4

Lutron Electronics Co., Inc.7200 Suter RoadCoopersburg, PA 18036-1299, U.S.A.

12/2013P/N 045404 Rev. B Lutron, O, Serena and Pico are registered trademarks of Lutron Electronics Co., Inc.

Serena® Roller Shade Installation and Setup Guide Page 2

The favorite level is factory programmed to the midpoint between the factory programmed upper and lower shade limits.

SET UPPER LIMITWith the shade at the

preferred upper limit, press and hold the Open Button.

A diagram on the battery holder shows quantity and orientation. When all batteries are inserted properly, the shade button LED (see section 5 ) will flash red/green as the shade powers up.

6 Adjusting shade limits (OPTIONAL):

The shade’s upper and lower limits are pre-programmed based on the window dimensions and mounting option. If adjustment is needed, follow these steps:

A Serena® roller shade

NOTE: Restoring a Serena® roller shade to its factory default settings will remove all control assignments and favorite programming. Upper and lower limits are retained.

• Tap the Shade button 3 times, (triple-tap), then press and hold. The Shade Button LED will illuminate and flash GREEN rapidly while you continue to hold.

• Release the button and immediately triple-tap it again; (do not hold). The Shade Button LED will flash GREEN rapidly, then flash RED/GREEN three times, and turn off. When the LED stops flashing, the shade has been restored to factory default settings.

C Serena® 4-Group RF remote control*

• Tap the All Shade Groups button.

• Tap the Open or Close button 3 times, (triple-tap), then press and hold. The All Shade Groups button LED will illuminate and stay on for approximately 3 to 5 seconds while you continue to hold.

• Keep the button pressed until the All Shade Groups button LED turns off.

• Release the button and immediately triple-tap it again; (do not hold). The LED’s of Shade Group buttons 1 - 4, and the All Shade Groups button will illuminate and stay on for approximately 3 to 5 seconds. When all LED’s turn off, the control has been restored to factory default settings.

B Pico® wireless control*

• Tap the Open or Close button 3 times, (triple-tap), then press and hold. The LED next to the Open button will illuminate and stay on while you continue to hold.

• Release the button and immediately triple-tap it again; (do not hold). The LED will flash quickly. When the LED stops flashing, the control has been restored to factory default settings.

Serena® 4-Group RF remote control

Shade Button with LED

5 Assigning a remote control:

Pico® wireless control

Without Optional Fascia: rotate the top section forward. Without Optional Fascia: rotate the top section back to the closed position

OpenOpen

FavoriteFavorite

Close

Close

Shade Groups

Lower

Lower

All Shade Groups

Raise

Raise

5.1 Assign a Pico® wireless control

c. Press and hold the Close button.

a. Tap the Shade Button.

a. Tap the Shade Button.

b. The Shade Button illuminates.

b. The Shade Button illuminates.

d. The Shade Button flashes. Assignment is complete.

d. The Shade Button flashes. Assignment is complete.

e. Repeat for additional shade/control assignments.

e. Repeat for additional shade/control assignments.

5.2 Assign a Serena® 4-Group RF remote control

c. Choose a Shade Group button. Press and hold.

d. The Shade Button flashes, then stays on.

Compatible remote controls (sold separately)

c. Press and hold the Open and Raise Buttons.

e. Use the Raise and Lower Buttons to position the shade at the preferred upper or lower limit.

a. Tap the Shade Button.

b. The Shade Button illuminates.

g. The Shade Button flashes. Limit set is complete.

4 Installing the batteries:

4.1 Open the battery holder at the top of the shade. 4.2 Insert new D-cell alkaline batteries. 4.3 Return the battery holder to the closed position.

Worldwide Headquarters | USALutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036-1299 USATEL: 1.610.282.3800 • FAX: 1.610.282.3090Technical Support: 1.800.523.9466 • Toll Free: 1.888.LUTRON1Email: shadinginfo@lutron.com • Online: www.lutron.com/shadingsolutions

Europe Headquarters | United KingdomLutron EA Ltd. 6 Sovereign Close, London, E1W3JF, UKTEL: +44.(0)20.7702.0657 • FAX: +44.(0)20.7480.6899Technical Support: +44.(0)20.7680.4481FREEPHONE: 0800.282.107

For complete warranty information, please see: www.serenashades.com/warranty

OR SET LOWER LIMITWith the shade at the

preferred lower limit, press and hold the Close Button.

With Optional Fascia: pull out, then down on the fascia. With Optional Fascia: push the fascia up, then in.

Restoring factory default settings:

*NOTE: Restoring factory default settings will remove all shade assignments and favorite programming.

f.

b. Press and hold the Favorite Button.

c. The Shade Button flashes. Favorite level is set.

a. Use the Raise and Lower Buttons to position the shade at the desired favorite level.

NOTE: When setting differing favorite levels among multiple shades assigned to the same control, disconnect power to the shades you do not want affected by removing one battery from each.

FCC InformationModels: SYC-J-EDU-R2, QSFC-J-EDU-R2This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may

cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003.

IC InformationThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject tot he following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired

operation of the device.

7 Setting a favorite level (OPTIONAL):