TSERIES

Full Metal Luminance

contacts

contact arrangement 1C (1 Form C), 2C (2 Form C)

contact material Ag alloy (24K gold tint)

regular insulating voltage 250VAC

maximum carry current 3A max.

maximum switching voltage 250VAC, 110VDC

rated load1A 24VDC / 120VAC

0.5A 250VAC

min applicable load 10mA 5VDC

LED

color red, green, yellow, blue, white, orange

appearance round

norminal voltage 24VDC, 12VDC, 6VDC, 220VAC, 110VAC

norminal current 15mA approx.

expected Life 1) 50,000hours

1) �Luminance is reduced to 50% of inital intensity after being lit for 50,000 hours continuously.

SPECIFICATION

Generalspecification

contact resistance max. 50mΩ

insulation resistance min. 100MΩ (500VDC)

dieletric strength 2,000VAC for1min.

vibration resistance 5~55Hz dual amplitude : 0.75mm

shock resistance endurance: 500m/s2, operation error : 200m/s2

expected life

mechanicalmomentary : 1,000,000 min, selector : 250,000 min,

alternate : 100,000 min.

electricalmomentary : min. 100,000 (frequency of on/off 1,200 times / hour)

alternate min. 50,000

ambient temperature -25℃ ~ +55℃ (with no icing)

ambient humidity 45% ~ 85%RH

degree of protection IP65 waterproof

terminal soldering temperature 20W 5sec / 260℃ 3sec

1 description 1 : pilot Lamp4 : 2step selector7 : 3 step Key

2 : momentary5 : 3step selector8 : emergency reset (nominal)

3 : alternate6 : 2 step key

2 illumination & bezel shape 1 : round7 : LED round

2 : square8 : LED square

3 : rectangular9 : LED rectangular

3 contact arrangement 0 : no contact 1 : 1a + 1b 2 : 2a + 2b

4 lens color R : redB : blue

G : greenO : orange

Y : yellowW : white

5 norminal votage 6VDC110VAC

12VDC220VAC

24VDC

T19 SeriesT19 - ❶ ❷ ❸ ❹ ❺

PART NUMBER DESCRIPTION

pilot lamp

bezel shape

momentary & alternate push button switch

bezel shape

selector switch

bezel shape

key switch

bezel shape

emergency reset switch

bezel shape

socket

K16-S113 (soldering socke) K16-S114 (P.C.B. socket)

24.0

18.0

DIMENSION

4.5

4.0

18.0

WIRING DIAGRAM

Bottom Viewilluminated

LED�LampTerminae

illuminated2a + 2b

illuminated1a + 1b

Panel cut-outpilot push button key selector switch emergency

19.0 + 0.2 19.0 + 0.2

Min

26.0

Min

35.0

Min 26.0 Min 35.0

SPECIFICATION

1 description 1 : pilot Lamp 2 : momentary 3 : alternate

2 illumination & bezel shape 1 : round 7 : LED round

3 contact arrangement 0 : no contact 1 : 1a + 1b (T22) 2 : 2a + 2b (T25)

4 lens color R : redB : blue

G : greenO : orange

Y : yellowW : white

5 norminal votage 6VDC110VAC

12VDC220VAC

24VDC

T22/25 SeriesT22/25 - ❶ ❷ ❸ ❹ ❺

generalpecification

regular insulating voltage 250VAC/DC

insulation resistance min 100MΩ (500VDC)

dieletric strength

between the charging section and the earth

min. 2,000VAC (1min.)

between the charging sections min. 1,500VAC (1min.)

expected lifemechanical

momentary : 1,000,000 min.

alternate : 250,000 min.

electrical min. 100,000

frequency of on/off 1200 times / hour

vibration dual wave length 0.1mm (10-55Hz)

impactoperation error : 100㎨durability : 500㎨

ambient temperature -20 ~ +70℃ (anti-freezing)

relative humidity 45 ~ 85%RH (at -5 ~ +40℃)

controlling protection structure IP65 (water/oil proof)

contacts

contact arrangementT22 : 1C(1a+1b)T25 : 1C(1a+1b), 2C(2a+2b)

contact material Ag alloy (24K gold tint)

regular insulating voltage 250VAC

regular applicable current 5A max.

max. on/off voltage 250VAC / 110VDC

regular current used

resistance load (AC12/DC12) induction load (AC13/DC13)

3A 24VDC 0.7A 24VDC

0.2A 125VDC 0.15A 125VDC

3A 110VAC 1A 110VAC

1.5A 250VAC 0.7A 250VAC

min. applicable current 10mA 5VDC

lit part

color red, green, yellow, blue, white

appearance round

regular current used 24VDC, 12VDC, 6VDC, 220VAC(to be released)

norminal current 15mA Approx.

expected life 50,000hrs

lamp type LED

PART NUMBER DESCRIPTION

pilot lamppanel cut-out

bezel shape

pilot lamppanel cut-out

bezel shape

DIMENSION

T22

T25

1. Connection of wires

1) Soldering

•The power consumption of the soldering iron must be 30 W or less.

•Use a 30 W soldering iron for 5 s or less, and a 20 W soldering iron for 10 s or less.

2) Tab terminal

•Use the #110 tab terminal.

3) Wires for connection

•Single wire: Max.Ø0.8mm

•Stranded wire: Max. 0.75mm2

2. Replacement/installation of the front button and LED

1) Button : Use a driver in the groove on the side of the button to remove it (To insert the button, push it until it clicks.).

2) LED : Pull the LED using a tool such as pliers. Assemble it in the reverse sequence of the disassembly.

3. Mounting the product on the panel

1) Press both the projections of the contact unit module with two fingers to remove the module from the operating unit.

2) The operating unit and contact unit module have their directivity. Use caution for insertion.

3) Separate the fixing ring and anti-rotation fixture from the operating unit.

4) Insert the operating unit in the panel, and assemble it in the reverse order of the disassembly.

5) The fixing ring can be firmly tightened using the K16-W1.

4. Contact block replacement/installation

1) Widen four projections on both sides of the contact unit module to separate the contact block.

2) Push the contact block into the empty space of the contact unit module to assemble it. The block is mounted with a click sound.

(Be sure to check the left and right sides are firmly locked.)

3) A maximum of three (3a+3b) contact blocks can be mounted.

5. When using a Ø16 small control switch as the power switch for the control unit, please follow the following instruction for longer product life span and reliability.

S/W Contact

S/W Contact

6. When rectifying the AC current for the DC power for lighting, the DC power must be a constant voltage source with a ripple range of 10 % or less. Otherwise, the LED life is significantly reduced7. Do not apply excessive impact or force to prevent damage to the product. When using the K16-W1 tool, do not tighten the fixing ring with an excessive force, because it may damage the product (When fixing the product on the panel, the tightening torque must be 0.6~1 N·m or less).8. When soldering the terminal for wiring, comply with the specified temperature and time. Failure to meet the specifications may lead to the damage and thermal defromation to the product.

pre-caution

1588-4036+82-32-575-4036

www.kacon.co.kr

Copyright ⓒ 2012 KOREA AUTO CONTROLS CO., LTD. All Rights Reserved.

ISBN-KAP-1207 1.0K